[openwrt/openwrt] ramips: mt76x8: add support for Cudy LT400E v1
LEDE Commits
lede-commits at lists.infradead.org
Mon Jan 19 16:47:47 PST 2026
hauke pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/1c62e21a8d4a11f169a00a8de0ee8e8d9c73c94c
commit 1c62e21a8d4a11f169a00a8de0ee8e8d9c73c94c
Author: Kamil Jońca <kjonca at onet.pl>
AuthorDate: Tue Jan 6 09:03:33 2026 +0100
ramips: mt76x8: add support for Cudy LT400E v1
This commit adds support for the Cudy LT400E v1,
an indoor 4G/LTE WiFi router.
It has 4x10/100 Mbps Ethernet ports, a 2.4 GHz radio,
and a Quectel 4G/LTE EC200A modem.
Hardware:
SoC: MediaTek MT7628NN
Flash: 8 MiB SPI
RAM: 64 MiB
Ethernet: 4x10/100 Mbps
WiFi: 2.4 GHz (embedded MT7628, 802.11n)
WWAN: Quectel EC200A-EL 4G/LTE Cat 4 modem
SIM: nano-SIM slot
Buttons: 1 Reset button, 1 WPS button
LEDs: 10x (blue)
Power: 12 V DC barrel jack
Installation:
The stock firmware is a customized variant of OpenWrt, which implements
a signature check that only allows flashing official firmware. Cudy
offers, on their website [1][6], intermediate OpenWrt firmware images
which do not implement the signature check. After flashing the
intermediate image, the upstream (i.e., official) OpenWrt image can be
installed. See the device's entry in OpenWrt's Wiki for more details [2].
Cellular network:
The Quectel EC200A modem is internally connected to the SoC via USB, and
operates in ECM mode, supported by the CDC Ether driver [3]. When
inserting a SIM card in the slot, if no PIN is needed, the network
interface "usb0" is brought up and the cellular connection works out of
the box. To interact with the modem directly (unlock the PIN, change APN
and PDP settings, etc.), AT commands can be sent with picocom to serial
port /dev/ttyUSB2 [4].
Recovery:
The stock firmware can be recovered via TFTP, as the bootloader (based
on U-Boot) implements a recovery client. Set up a TFTP server on your
computer with IP 192.168.88.1/24 serving the stock firmware from Cudy's
website renamed to "recovery.bin". Press the Reset button (keep it
pressed), power on the device, wait for the TFTP server to send the
recovery.bin file, then release the Reset button. The router will take a
couple of minutes to reboot and set up the stock firmware. See the
device's entry in OpenWrt's Wiki for more details [2].
Discussion:
Use the dedicated thread in OpenWrt's forum to discuss any aspects [5].
Acknowledgments:
The code to support this device is largely based on the sources kindly
provided by Cudy in compliance with the GPL license. Thanks for
supporting the OpenWrt community.
Links:
[1] https://www.cudy.com/blogs/faq/openwrt-software-download
[2] https://openwrt.org/toh/cudy/lt400e_v1
[3] https://openwrt.org/docs/guide-user/network/wan/wwan/ethernetoverusb_cdc
[4] https://openwrt.org/docs/guide-user/network/wan/wwan/at_commands
[5] https://forum.openwrt.org/t/242466
[6] https://drive.google.com/drive/folders/1BKVarlwlNxf7uJUtRhuMGUqeCa5KpMnj
Co-authored-by: rogerpueyo <roger.pueyo at guifi.net>
Signed-off-by: Kamil Jońca <kjonca at onet.pl>
Link: https://github.com/openwrt/openwrt/pull/21246
Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
---
.../linux/ramips/dts/mt7628an_cudy_lt400e-v1.dts | 225 +++++++++++++++++++++
target/linux/ramips/image/mt76x8.mk | 11 +
.../ramips/mt76x8/base-files/etc/board.d/01_leds | 8 +
.../mt76x8/base-files/etc/board.d/02_network | 7 +
4 files changed, 251 insertions(+)
diff --git a/target/linux/ramips/dts/mt7628an_cudy_lt400e-v1.dts b/target/linux/ramips/dts/mt7628an_cudy_lt400e-v1.dts
new file mode 100644
index 0000000000..5ced75c65c
--- /dev/null
+++ b/target/linux/ramips/dts/mt7628an_cudy_lt400e-v1.dts
@@ -0,0 +1,225 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7628an.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ compatible = "cudy,lt400e-v1", "mediatek,mt7628an-soc";
+ model = "Cudy LT400E v1";
+
+ aliases {
+ led-boot = &led_power;
+ led-running = &led_power;
+ led-failsafe = &led_power;
+ led-upgrade = &led_power;
+ label-mac-device = ðernet;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
+ };
+
+ internet {
+ function = LED_FUNCTION_MOBILE;
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
+ };
+
+ wifi {
+ function = LED_FUNCTION_WLAN;
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
+ };
+
+ lan1 {
+ function = LED_FUNCTION_LAN;
+ color = <LED_COLOR_ID_BLUE>;
+ function-enumerator = <1>;
+ gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
+ };
+
+ lan2 {
+ function = LED_FUNCTION_LAN;
+ color = <LED_COLOR_ID_BLUE>;
+ function-enumerator = <2>;
+ gpios = <&gpio 43 GPIO_ACTIVE_LOW>;
+ };
+
+ lan3 {
+ function = LED_FUNCTION_LAN;
+ color = <LED_COLOR_ID_BLUE>;
+ function-enumerator = <3>;
+ gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
+ };
+
+ lan4 {
+ function = LED_FUNCTION_LAN;
+ color = <LED_COLOR_ID_BLUE>;
+ function-enumerator = <4>;
+ gpios = <&gpio 45 GPIO_ACTIVE_LOW>;
+ };
+
+ signal1 {
+ label = "blue:signal1";
+ gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+ };
+
+ signal2 {
+ label = "blue:signal2";
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ };
+
+ led-signal3 {
+ label = "blue:signal3";
+ gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-export {
+ compatible = "gpio-export";
+
+ usb4g {
+ gpio-export,name = "4g";
+ gpio-export,output = <0>;
+ gpios = <&gpio 3 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+};
+
+
+&state_default {
+ gpio {
+ groups = "i2c", "gpio", "wdt", "p0led_an", "wled_an";
+ function = "gpio";
+ };
+};
+
+&pcie0 {
+ wifi at 0,0 {
+ compatible = "mediatek,mt76";
+ reg = <0x0000 0 0 0 0>;
+ nvmem-cells = <&eeprom_factory_8000>, <&macaddr_bdinfo_de00 2>;
+ nvmem-cell-names = "eeprom", "mac-address";
+ ieee80211-freq-limit = <5000000 6000000>;
+ };
+};
+
+&wmac {
+ status = "okay";
+
+ nvmem-cells = <&eeprom_factory_0>, <&macaddr_bdinfo_de00 0>;
+ nvmem-cell-names = "eeprom", "mac-address";
+};
+
+ðernet {
+ nvmem-cells = <&macaddr_bdinfo_de00 0>;
+ nvmem-cell-names = "mac-address";
+};
+
+&ehci {
+ status = "okay";
+};
+
+&ohci {
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition at 30000 {
+ label = "u-boot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ eeprom_factory_0: eeprom at 0 {
+ reg = <0x0 0x400>;
+ };
+
+ eeprom_factory_8000: eeprom at 8000 {
+ reg = <0x8000 0x4da8>;
+ };
+ };
+ };
+
+ partition at 50000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x50000 0x7a0000>;
+ };
+
+ partition at ff0000 {
+ label = "bdinfo";
+ reg = <0x7f0000 0x10000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_bdinfo_de00: macaddr at de00 {
+ compatible = "mac-base";
+ reg = <0xde00 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+ };
+ };
+ };
+ };
+};
diff --git a/target/linux/ramips/image/mt76x8.mk b/target/linux/ramips/image/mt76x8.mk
index 50c8ed726f..e379f253d4 100644
--- a/target/linux/ramips/image/mt76x8.mk
+++ b/target/linux/ramips/image/mt76x8.mk
@@ -199,6 +199,17 @@ define Device/creality_wb-01
endef
TARGET_DEVICES += creality_wb-01
+define Device/cudy_lt400e-v1
+ IMAGE_SIZE := 7808k
+ DEVICE_VENDOR := Cudy
+ DEVICE_MODEL := LT400E
+ DEVICE_VARIANT := v1
+ DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-usb-net-cdc-ether \
+ kmod-usb-serial-option
+ SUPPORTED_DEVICES += cudy,lt400e
+endef
+TARGET_DEVICES += cudy_lt400e-v1
+
define Device/cudy_m1200-v1
IMAGE_SIZE := 15872k
DEVICE_VENDOR := Cudy
diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
index 94855c5ff7..c44975ae46 100644
--- a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
@@ -27,6 +27,14 @@ yuncore,m300)
creality,wb-01)
ucidef_set_led_switch "lan" "lan" "blue:lan" "switch0" "0x1"
;;
+cudy,lt400e-v1)
+ ucidef_set_led_switch "lan1" "lan1" "blue:lan-1" "switch0" "0x08"
+ ucidef_set_led_switch "lan2" "lan2" "blue:lan-2" "switch0" "0x04"
+ ucidef_set_led_switch "lan3" "lan3" "blue:lan-3" "switch0" "0x02"
+ ucidef_set_led_switch "lan4" "lan4" "blue:lan-4" "switch0" "0x01"
+ ucidef_set_led_netdev "wifi" "wifi" "blue:wlan" "phy0-ap0"
+ ucidef_set_led_netdev "internet" "internet" "blue:internet" "usb0"
+ ;;
cudy,wr1000)
ucidef_set_led_switch "wan" "wan" "blue:wan" "switch0" "0x10"
ucidef_set_led_switch "lan1" "lan1" "blue:lan1" "switch0" "0x08"
diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
index 832207dcf1..f0d86bb366 100644
--- a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
@@ -100,6 +100,13 @@ ramips_setup_interfaces()
ucidef_add_switch "switch0" \
"4:lan" "6 at eth0"
;;
+ cudy,lt400e-v1)
+ ucidef_add_switch "switch0" \
+ "3:lan:1" "2:lan:2" "1:lan:3" "0:lan:4" "6 at eth0"
+ ucidef_set_interface "wwan" device "usb0" protocol "dhcp"
+ uci add_list firewall. at zone[1].network='wwan'
+ uci add_list firewall. at zone[1].network='wwan6'
+ ;;
cudy,m1200-v1|\
cudy,tr1200-v1)
ucidef_add_switch "switch0" \
More information about the lede-commits
mailing list