[openwrt/openwrt] mvebu: Add support for WD MyCloud EX2 Ultra
LEDE Commits
lede-commits at lists.infradead.org
Sun Jan 4 15:27:17 PST 2026
hauke pushed a commit to openwrt/openwrt.git, branch openwrt-25.12:
https://git.openwrt.org/a1bb2cbb9dc1243f149a9f50b5f686dca091c9b6
commit a1bb2cbb9dc1243f149a9f50b5f686dca091c9b6
Author: Robert Senderek <robert.senderek at 10g.pl>
AuthorDate: Wed Nov 12 10:08:37 2025 +0100
mvebu: Add support for WD MyCloud EX2 Ultra
Hardware
--------
Marvell Armada 385 (MV88F6820)
1GB RAM
256MB NAND
1x 1Gbit
2x USB 3.0
2x SATA-III
UART: 115200 8N1 3.3V
RTC
Weltrend MCU WT6703F connected via UART1 for Power LED / PWM Fan / hw reset / WoL
Installation
------------
Connect UART 3.3V adapter to JP2 pins: 1-RX / 2-GND / 5-TX
Use USB2.0 FAT32 pendrive with openwrt-mvebu-cortexa9-wd_cloud-ex2-ultra-initramfs-kernel.bin
1. stop boot by pressing 1
2. usb start
3. fatload usb 0:1 0x02000000 openwrt-mvebu-cortexa9-wd_cloud-ex2-ultra-initramfs-kernel.bin;bootm 0x02000000 -
4. do backup mtd1 mtd3
5. use sysupgrade
Or tftp
1. stop boot by pressing 1
2. setenv ethact egiga2;setenv serverip 192.168.11.114;setenv ipaddr 192.168.11.113
3. tftpboot 0x02000000 openwrt-mvebu-cortexa9-wd_cloud-ex2-ultra-initramfs-kernel.bin; bootm 0x02000000 -
4. do backup mtd1 mtd3
5. use sysupgrade
or Evgeny Kolesnikov <evgenyz at gmail.com> method from his failed PR 2040
- Using original firmware's network settings obtain SSH access to the device.
- Put *-image-cfs-factory.bin and *-uImage-factory.bin images into device's /tmp directory.
- Write kernel (uImage) image 'flash_eraseall /dev/mtd1 && nandwrite --markbad -p /dev/mtd1 /tmp/*-uImage-factory.bin'.
- Write rootfs (image-cfs) image 'ubiformat /dev/mtd3 -f /tmp/*-image.cfs-factory.bin -y'.
- Reboot the device.
Installation (upgrade):
Use *-sysupgrade.bin in a usual way.
Weltrend MCU control is done via uart1 19200
install coreutils-stty
stty -F /dev/ttyS1 raw speed 19200
stty -F /dev/ttyS1 raw speed 19200
PWM Fan Control
off: 00
echo -n -e '\xfa\x02\x00\x00\x00\x00\xfb' > /dev/ttyS1
slow: 5F
echo -n -e '\xfa\x02\x00\x5f\x00\x00\xfb' > /dev/ttyS1
max: FF
echo -n -e '\xfa\x02\x00\xff\x00\x00\xfb' > /dev/ttyS1
Power LED Control
Blue
echo -n -e '\xfa\x26\x00\x11\x00\x01\xfb' > /dev/ttyS1
Red
echo -n -e '\xfa\x26\x00\x14\x00\x01\xfb' > /dev/ttyS1
Orange
echo -n -e '\xfa\x26\x00\x12\x00\x01\xfb' > /dev/ttyS1
more here: https://github.com/c-MM/mcm-daemon/blob/master/mcm.h
Signed-off-by: Robert Senderek <robert.senderek at 10g.pl>
Link: https://github.com/openwrt/openwrt/pull/17779
(cherry picked from commit 96ad29a0f3e5fd1c05d685aa3cda1e7940fa4e5c)
Link: https://github.com/openwrt/openwrt/pull/21364
Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
---
.../cortexa9/base-files/etc/board.d/02_network | 2 +
.../cortexa9/base-files/lib/upgrade/platform.sh | 1 +
.../dts/marvell/armada-385-wd_cloud-ex2-ultra.dts | 13 +
.../marvell/armada-385-wd_cloud-mirror-gen2.dts | 359 +--------------------
...ud-mirror-gen2.dts => armada-385-wd_cloud.dtsi} | 8 -
target/linux/mvebu/image/cortexa9.mk | 17 +
6 files changed, 35 insertions(+), 365 deletions(-)
diff --git a/target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network b/target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network
index 484ebe3db2..cd0f4c99c4 100644
--- a/target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network
+++ b/target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network
@@ -14,6 +14,7 @@ mvebu_setup_interfaces()
case "$board" in
ctera,c200-v2|\
synology,ds213j|\
+ wd,cloud-ex2-ultra|\
wd,cloud-mirror-gen2)
ucidef_set_interface_lan "eth0" "dhcp"
;;
@@ -96,6 +97,7 @@ mvebu_setup_macs()
lan_mac=$label_mac
wan_mac=$label_mac
;;
+ wd,cloud-ex2-ultra|\
wd,cloud-mirror-gen2)
# mac address is on ubi "config" or ubi "reserve2" in text file.
# ubi "reserve2" /dev/mtd7 is twice small and only contains basic OEM factory info
diff --git a/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh b/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh
index 9f24fcfdef..a30f4bc1e2 100755
--- a/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh
+++ b/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh
@@ -32,6 +32,7 @@ platform_do_upgrade() {
nand_do_upgrade "$1"
;;
buffalo,ls421de|\
+ wd,cloud-ex2-ultra|\
wd,cloud-mirror-gen2)
nand_do_upgrade "$1"
;;
diff --git a/target/linux/mvebu/files/arch/arm/boot/dts/marvell/armada-385-wd_cloud-ex2-ultra.dts b/target/linux/mvebu/files/arch/arm/boot/dts/marvell/armada-385-wd_cloud-ex2-ultra.dts
new file mode 100644
index 0000000000..e9e2dc4186
--- /dev/null
+++ b/target/linux/mvebu/files/arch/arm/boot/dts/marvell/armada-385-wd_cloud-ex2-ultra.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/dts-v1/;
+#include "armada-385-wd_cloud.dtsi"
+
+/ {
+ model = "WD MyCloud Ex2 Ultra";
+ compatible = "wd,cloud-ex2-ultra", "marvell,armada385", "marvell,armada380";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x40000000>; /* 1GB */
+ };
+};
diff --git a/target/linux/mvebu/files/arch/arm/boot/dts/marvell/armada-385-wd_cloud-mirror-gen2.dts b/target/linux/mvebu/files/arch/arm/boot/dts/marvell/armada-385-wd_cloud-mirror-gen2.dts
index 97edc4ca46..03b6d7b18f 100644
--- a/target/linux/mvebu/files/arch/arm/boot/dts/marvell/armada-385-wd_cloud-mirror-gen2.dts
+++ b/target/linux/mvebu/files/arch/arm/boot/dts/marvell/armada-385-wd_cloud-mirror-gen2.dts
@@ -1,368 +1,13 @@
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Device Tree file for Western Digital My Cloud Mirror Gen 2
- * (BWVZ/Grand Teton)
- *
- * Copyright (C) 2020
- *
- * Based on the code from:
- *
- * Copyright (C) 2019 Evgeny Kolesnikov <evgenyz at gmail.com>
- * Copyright (C) 2016 Martin Mueller <mm at sig21.net>
- * Copyright (C) 2013 Gregory CLEMENT <gregory.clement at free-electrons.com>
- * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
- *
- */
-
/dts-v1/;
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/leds/common.h>
-#include "armada-385.dtsi"
+#include "armada-385-wd_cloud.dtsi"
/ {
model = "WD MyCloud Mirror Gen 2 (BWVZ/Grand Teton)";
compatible = "wd,cloud-mirror-gen2", "marvell,armada385", "marvell,armada380";
- aliases {
- led-boot = &led_boot;
- led-failsafe = &led_boot;
- led-upgrade = &led_boot;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- append-rootblock = "nullparameter="; /* override the bootloader args */
- };
-
memory {
device_type = "memory";
- reg = <0x00000000 0x20000000>; /* 512 MB */
- };
-
- soc {
- ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
- MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
- MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
- MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
- MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
-
- internal-regs {
- timer at c200 {
- status = "okay";
- };
-
- i2c0: i2c at 11000 {
- status = "okay";
- clock-frequency = <100000>;
- };
-
- i2c1: i2c at 11100 {
- status = "okay";
- clock-frequency = <100000>;
- };
-
- serial at 12000 {
- status = "okay";
- };
-
- /* Connected to Welltrend 6703F-OG240WT MCU
- * which controls power, fan and other things
- */
- serial at 12100 {
- status = "okay";
- };
-
- pinctrl at 18000 {
- /* use only one pin for UART1, as mpp20 is used by sata0 */
- uart1_pins: uart-pins-1 {
- marvell,pins = "mpp19";
- marvell,function = "ua1";
- };
-
- xhci0_vbus_pins: xhci0-vbus-pins {
- marvell,pins = "mpp26";
- marvell,function = "gpio";
- };
-
- xhci1_vbus_pins: xhci1-vbus-pins {
- marvell,pins = "mpp27";
- marvell,function = "gpio";
- };
-
- sata0_pins: sata-pins-0 {
- marvell,pins = "mpp55";
- marvell,function = "sata0";
- };
-
- sata1_pins: sata-pins-1 {
- marvell,pins = "mpp56";
- marvell,function = "sata1";
- };
-
- sata_leds: sata-leds {
- marvell,pins = "mpp43", "mpp52", "mpp53", "mpp54";
- marvell,function = "gpio";
- };
-
- btn_pins: btn-pins {
- marvell,pins = "mpp50";
- marvell,function = "gpio";
- };
- };
-
- usb at 58000 {
- status = "okay";
- };
-
- phy: mdio at 72004 {
- phy0: ethernet-phy at 0 {
- /* Init ETH LEDs */
- marvell,reg-init = <3 16 0 0x101e>;
- reg = <0>;
- };
- };
-
- sata at a8000 {
- status = "okay";
- };
-
- nand-controller at d0000 {
- status = "okay";
-
- nand: nand at 0 {
- reg = <0>;
- label = "pxa3xx_nand-0";
- nand-rb = <0>;
- marvell,nand-keep-config;
- #marvell,nand-enable-arbiter; //optional
- nand-on-flash-bbt;
- nand-ecc-strength = <4>;
- nand-ecc-step-size = <512>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition at 0 {
- label = "U-Boot";
- reg = <0x00000000 0x00500000>; /* 5 MB */
- read-only;
- };
-
- partition at 500000 {
- label = "kernel";
- reg = <0x00500000 0x00500000>; /* 5 MB */
- };
-
- partition at a00000 {
- label = "uRamdisk";
- reg = <0x00a00000 0x00500000>; /* 5 MB */
- read-only;
- };
-
- partition at f00000 {
- label = "ubi";
- reg = <0x00f00000 0x0b900000>; /* 185 MB */
- };
-
- partition at c800000 {
- label = "rescue fw";
- reg = <0x0c800000 0x00f00000>; /* 15 MB */
- read-only;
- };
-
- partition at d70000 {
- label = "config";
- reg = <0x0d700000 0x01400000>; /* 20 MB */
- read-only;
- };
-
- partition at eb00000 {
- label = "reserve1";
- reg = <0x0eb00000 0x00a00000>; /* 10 MB */
- read-only;
- };
-
- partition at f500000 {
- label = "reserve2";
- reg = <0x0f500000 0x00a00000>; /* 10 MB */
- read-only;
- };
- };
- };
- };
-
- usb3 at f0000 {
- usb-phy = <&usb3_0_phy>;
- status = "okay";
- };
-
- usb3 at f8000 {
- usb-phy = <&usb3_1_phy>;
- status = "okay";
- };
- };
- };
-
- gpio-leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&sata_leds>;
-
- led_boot: s1red {
- label = "red:hdd1";
- gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
- };
- s2red {
- label = "red:hdd2";
- gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
- };
- s1blue {
- label = "blue:hdd1";
- gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
- linux,default-trigger = "ata1";
- };
- s2blue {
- label = "blue:hdd2";
- gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
- linux,default-trigger = "ata2";
- };
- };
-
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&btn_pins>;
-
- reset {
- label = "reset";
- linux,code = <KEY_RESTART>; // Restart=0x198, Power=0x116
- gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-
- usb3_0_phy: usb3_0_phy {
- compatible = "usb-nop-xceiv";
- vcc-supply = <®_usb3_0_vbus>;
- };
-
- usb3_1_phy: usb3_1_phy {
- compatible = "usb-nop-xceiv";
- vcc-supply = <®_usb3_1_vbus>;
- };
-
- reg_usb3_0_vbus: usb3-vbus0 {
- compatible = "regulator-fixed";
- regulator-name = "usb3-vbus0";
- pinctrl-names = "default";
- pinctrl-0 = <&xhci0_vbus_pins>;
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- enable-active-high;
- regulator-always-on;
- gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
- };
-
- reg_usb3_1_vbus: usb3-vbus1 {
- compatible = "regulator-fixed";
- regulator-name = "usb3-vbus1";
- pinctrl-names = "default";
- pinctrl-0 = <&xhci1_vbus_pins>;
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- enable-active-high;
- regulator-always-on;
- gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>;
- };
-
- reg_sata0: pwr-sata0 {
- compatible = "regulator-fixed";
- regulator-name = "pwr_en_sata0";
- regulator-min-microvolt = <12000000>;
- regulator-max-microvolt = <12000000>;
- enable-active-high;
- regulator-boot-on;
- gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
- };
-
- reg_5v_sata0: v5-sata0 {
- compatible = "regulator-fixed";
- regulator-name = "v5.0-sata0";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- vin-supply = <®_sata0>;
- };
-
- reg_12v_sata0: v12-sata0 {
- compatible = "regulator-fixed";
- regulator-name = "v12.0-sata0";
- regulator-min-microvolt = <12000000>;
- regulator-max-microvolt = <12000000>;
- vin-supply = <®_sata0>;
- };
-
- reg_sata1: pwr-sata1 {
- compatible = "regulator-fixed";
- regulator-name = "pwr_en_sata1";
- regulator-min-microvolt = <12000000>;
- regulator-max-microvolt = <12000000>;
- enable-active-high;
- regulator-boot-on;
- gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
- };
-
- reg_5v_sata1: v5-sata1 {
- compatible = "regulator-fixed";
- regulator-name = "v5.0-sata1";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- vin-supply = <®_sata1>;
- };
-
- reg_12v_sata1: v12-sata1 {
- compatible = "regulator-fixed";
- regulator-name = "v12.0-sata1";
- regulator-min-microvolt = <12000000>;
- regulator-max-microvolt = <12000000>;
- vin-supply = <®_sata1>;
- };
-};
-
-&bm {
- status = "okay";
-};
-
-&bm_bppi {
- status = "okay";
-};
-
-ð2 {
- status = "okay";
- phy = <&phy0>;
- phy-mode = "sgmii";
- buffer-manager = <&bm>;
- bm,pool-long = <0>;
- bm,pool-short = <1>;
-};
-
-&ahci0 {
- status = "okay";
- #address-cells = <1>;
- #size-cells = <0>;
-
- sata-port at 0 {
- reg = <0>;
- target-supply = <®_sata0>;
- #thermal-sensor-cells = <0>;
- };
-
- sata-port at 1 {
- reg = <1>;
- target-supply = <®_sata1>;
- #thermal-sensor-cells = <1>;
+ reg = <0x00000000 0x20000000>; /* 512MB */
};
};
diff --git a/target/linux/mvebu/files/arch/arm/boot/dts/marvell/armada-385-wd_cloud-mirror-gen2.dts b/target/linux/mvebu/files/arch/arm/boot/dts/marvell/armada-385-wd_cloud.dtsi
similarity index 97%
copy from target/linux/mvebu/files/arch/arm/boot/dts/marvell/armada-385-wd_cloud-mirror-gen2.dts
copy to target/linux/mvebu/files/arch/arm/boot/dts/marvell/armada-385-wd_cloud.dtsi
index 97edc4ca46..f32c838977 100644
--- a/target/linux/mvebu/files/arch/arm/boot/dts/marvell/armada-385-wd_cloud-mirror-gen2.dts
+++ b/target/linux/mvebu/files/arch/arm/boot/dts/marvell/armada-385-wd_cloud.dtsi
@@ -21,9 +21,6 @@
#include "armada-385.dtsi"
/ {
- model = "WD MyCloud Mirror Gen 2 (BWVZ/Grand Teton)";
- compatible = "wd,cloud-mirror-gen2", "marvell,armada385", "marvell,armada380";
-
aliases {
led-boot = &led_boot;
led-failsafe = &led_boot;
@@ -35,11 +32,6 @@
append-rootblock = "nullparameter="; /* override the bootloader args */
};
- memory {
- device_type = "memory";
- reg = <0x00000000 0x20000000>; /* 512 MB */
- };
-
soc {
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
diff --git a/target/linux/mvebu/image/cortexa9.mk b/target/linux/mvebu/image/cortexa9.mk
index 6c6889b542..570251424b 100644
--- a/target/linux/mvebu/image/cortexa9.mk
+++ b/target/linux/mvebu/image/cortexa9.mk
@@ -463,6 +463,23 @@ define Device/synology_ds213j
endef
TARGET_DEVICES += synology_ds213j
+define Device/wd_cloud-ex2-ultra
+ $(Device/NAND-128K)
+ DEVICE_VENDOR := Western Digital
+ DEVICE_MODEL := MyCloud EX2 Ultra
+ DEVICE_PACKAGES += -uboot-envtools mkf2fs e2fsprogs \
+ partx-utils kmod-hwmon-drivetemp -ppp -kmod-nft-offload -dnsmasq \
+ -odhcpd-ipv6only
+ DEVICE_DTS := armada-385-wd_cloud-ex2-ultra
+ KERNEL_SIZE := 5120k
+ KERNEL := kernel-bin | append-dtb | uImage none
+ KERNEL_INITRAMFS := kernel-bin | append-dtb | uImage none
+ IMAGES += image-cfs-factory.bin uImage-factory.bin
+ IMAGE/image-cfs-factory.bin := append-ubi
+ IMAGE/uImage-factory.bin := append-kernel
+endef
+TARGET_DEVICES += wd_cloud-ex2-ultra
+
define Device/wd_cloud-mirror-gen2
$(Device/NAND-128K)
DEVICE_VENDOR := Western Digital
More information about the lede-commits
mailing list