[openwrt/openwrt] mediatek: add support for Keenetic/Netcraze (K/N)AP-630
LEDE Commits
lede-commits at lists.infradead.org
Fri Feb 13 15:35:21 PST 2026
hauke pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/20644af030672d74f978d77142c5267757af2efa
commit 20644af030672d74f978d77142c5267757af2efa
Author: Maxim Anisimov <maxim.anisimov.ua at gmail.com>
AuthorDate: Wed Jan 21 18:09:31 2026 +0300
mediatek: add support for Keenetic/Netcraze (K/N)AP-630
This commit adds support for Keenetic/Netcraze (K/N)AP-630
Specification:
- MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
- 512MB RAM
- 128MB SPI NAND
- 1 led with two colors (green, orange)
- 1 button (reset)
- 1 2.5Gbit POE ethernet port based on Airoha EN8811H phy
Serial Interface:
- 3 Pins GND, RX, TX
- Settings: 115200, 8N1
Notes:
- The device supports dual boot mode
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Copy image to tftp server.
a) Keenetic
Rename "openwrt-mediatek-filogic-keenetic_kap-630-squashfs-factory.bin"
to "KAP-630_recovery.bin" and place it in tftp server directory.
b) Netcraze
Rename "openwrt-mediatek-filogic-netcraze_nap-630-squashfs-factory.bin"
to "NAP-630_recovery.bin" and place it in tftp server directory.
3. Connect PC with ethernet port, press the reset button, power up
the device and keep button pressed until status led start blinking.
4. Device will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua at gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21634
Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
---
.../mediatek/dts/mt7981b-keenetic-kap-630.dts | 8 +
.../mediatek/dts/mt7981b-keenetic-kap-630.dtsi | 245 +++++++++++++++++++++
.../mediatek/dts/mt7981b-netcraze-nap-630.dts | 8 +
.../filogic/base-files/etc/board.d/02_network | 2 +
.../etc/hotplug.d/ieee80211/11_fix_wifi_mac | 4 +-
target/linux/mediatek/image/filogic.mk | 35 +++
6 files changed, 301 insertions(+), 1 deletion(-)
diff --git a/target/linux/mediatek/dts/mt7981b-keenetic-kap-630.dts b/target/linux/mediatek/dts/mt7981b-keenetic-kap-630.dts
new file mode 100644
index 0000000000..25357e9a8b
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7981b-keenetic-kap-630.dts
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+#include "mt7981b-keenetic-kap-630.dtsi"
+
+/ {
+ model = "Keenetic KAP-630";
+ compatible = "keenetic,kap-630", "mediatek,mt7981";
+};
diff --git a/target/linux/mediatek/dts/mt7981b-keenetic-kap-630.dtsi b/target/linux/mediatek/dts/mt7981b-keenetic-kap-630.dtsi
new file mode 100644
index 0000000000..35fa54a284
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7981b-keenetic-kap-630.dtsi
@@ -0,0 +1,245 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+
+/dts-v1/;
+#include "mt7981b.dtsi"
+
+/ {
+ aliases {
+ label-mac-device = &gmac0;
+ led-boot = &status_led_green;
+ led-failsafe = &status_led_orange;
+ led-running = &status_led_green;
+ led-upgrade = &status_led_green;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ button-reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&pio 24 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ status_led_green: led-0 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&pio 11 GPIO_ACTIVE_HIGH>;
+ };
+
+ status_led_orange: led-1 {
+ color = <LED_COLOR_ID_ORANGE>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&pio 12 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ virtual_flash {
+ compatible = "mtd-concat";
+ devices = <&firmware1 &firmware2>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "kernel";
+ reg = <0x0 0x600000>;
+ };
+
+ partition at 400000 {
+ label = "ubi";
+ reg = <0x600000 0x0>;
+ };
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+ð {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio_pins>;
+
+ gmac0: mac at 0 {
+ compatible = "mediatek,eth-mac";
+ reg = <0>;
+ phy-mode = "2500base-x";
+ phy-handle = <&phy10>;
+
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&macaddr_factory_a>;
+ };
+};
+
+&mdio_bus {
+ /* Airoha EN8811H */
+ phy10: ethernet-phy at a {
+ reg = <0xa>;
+ interrupt-parent = <&pio>;
+ interrupts = <38 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&pio 22 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <20000>;
+ };
+};
+
+&pio {
+ spi0_flash_pins: spi0-pins {
+ mux {
+ function = "spi";
+ groups = "spi0", "spi0_wp_hold";
+ };
+
+ conf-pu {
+ pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
+ };
+
+ conf-pd {
+ pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
+ };
+ };
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_flash_pins>;
+ status = "okay";
+
+ /* Winbond W25N01GVZEIG (128M) */
+ spi_nand at 0 {
+ compatible = "spi-nand";
+ reg = <0>;
+
+ spi-max-frequency = <52000000>;
+ spi-tx-buswidth = <4>;
+ spi-rx-buswidth = <4>;
+
+ mediatek,nmbm;
+ mediatek,bmt-max-ratio = <1>;
+ mediatek,bmt-max-reserved-blocks = <64>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* bl2 */
+ partition at 0 {
+ label = "preloader";
+ reg = <0x0 0x80000>;
+ read-only;
+ };
+
+ /* fip */
+ partition at 80000 {
+ label = "u-boot";
+ reg = <0x80000 0x200000>;
+ read-only;
+ };
+
+ partition at 280000 {
+ label = "u-config";
+ reg = <0x280000 0x80000>;
+ read-only;
+ };
+
+ partition at 300000 {
+ label = "rf-eeprom";
+ reg = <0x300000 0x200000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ eeprom_factory_0: eeprom at 0 {
+ reg = <0x0 0x1000>;
+ };
+
+ macaddr_factory_a: macaddr at a {
+ reg = <0xa 0x6>;
+ };
+ };
+ };
+
+ firmware1: partition at 500000 {
+ label = "firmware_1";
+ reg = <0x500000 0x3500000>;
+ };
+
+ partition at 3a00000 {
+ label = "config_1";
+ reg = <0x3a00000 0x80000>;
+ read-only;
+ };
+
+ partition at 3a80000 {
+ label = "dump";
+ reg = <0x3a80000 0x80000>;
+ read-only;
+ };
+
+ partition at 3c00000 {
+ label = "u-state";
+ reg = <0x3c00000 0x20000>;
+ read-only;
+ };
+
+ partition at 3e80000 {
+ label = "u-config_res";
+ reg = <0x3e80000 0x80000>;
+ read-only;
+ };
+
+ partition at 3f00000 {
+ label = "rf-eeprom_res";
+ reg = <0x3f00000 0x200000>;
+ read-only;
+ };
+
+ firmware2: partition at 4100000 {
+ label = "firmware_2";
+ reg = <0x4140000 0x3500000>;
+ };
+
+ partition at 7600000 {
+ label = "config_2";
+ reg = <0x7600000 0x80000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&wifi {
+ nvmem-cell-names = "eeprom";
+ nvmem-cells = <&eeprom_factory_0>;
+ status = "okay";
+};
+
+&sgmiisys0 {
+ /delete-node/ mediatek,pnswap;
+};
diff --git a/target/linux/mediatek/dts/mt7981b-netcraze-nap-630.dts b/target/linux/mediatek/dts/mt7981b-netcraze-nap-630.dts
new file mode 100644
index 0000000000..81b0b51707
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7981b-netcraze-nap-630.dts
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+#include "mt7981b-keenetic-kap-630.dtsi"
+
+/ {
+ model = "Netcraze NAP-630";
+ compatible = "netcraze,nap-630", "mediatek,mt7981";
+};
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
index 9cdb56bc6a..69e403f937 100644
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
@@ -110,6 +110,8 @@ mediatek_setup_interfaces()
cudy,ap3000-v1|\
cudy,re3000-v1|\
kebidumei,ax3000-u22|\
+ keenetic,kap-630|\
+ netcraze,nap-630|\
netgear,eax17|\
netgear,wax220|\
openfi,6c|\
diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
index ea31a60308..5950a590a8 100644
--- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
+++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
@@ -153,9 +153,11 @@ case "$board" in
jdcloud,re-cp-03)
[ "$PHYNBR" = "1" ] && mmc_get_mac_binary factory 0xa > /sys${DEVPATH}/macaddress
;;
+ keenetic,kap-630|\
keenetic,kn-3711|\
keenetic,kn-3811|\
- keenetic,kn-3911)
+ keenetic,kn-3911|\
+ netcraze,nap-630)
[ "$PHYNBR" = "1" ] && \
macaddr_setbit_la "$(mtd_get_mac_binary rf-eeprom 0x4)" > /sys${DEVPATH}/macaddress
;;
diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk
index 4758b238d1..283ee32536 100644
--- a/target/linux/mediatek/image/filogic.mk
+++ b/target/linux/mediatek/image/filogic.mk
@@ -1785,6 +1785,32 @@ define Device/kebidumei_ax3000-u22
endef
TARGET_DEVICES += kebidumei_ax3000-u22
+define Device/keenetic_kap-630-common
+ DEVICE_DTS_DIR := ../dts
+ DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware \
+ kmod-phy-airoha-en8811h
+ UBINIZE_OPTS := -E 5
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ KERNEL_SIZE := 6144k
+ IMAGE_SIZE := 108544k
+ KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb | \
+ append-squashfs4-fakeroot
+ IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+ IMAGES += factory.bin
+ IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | \
+ append-ubi | check-size | zyimage -d $$(ZYIMAGE_ID) -v "$$(DEVICE_MODEL)"
+endef
+
+define Device/keenetic_kap-630
+ DEVICE_VENDOR := Keenetic
+ DEVICE_MODEL := KAP-630
+ DEVICE_DTS := mt7981b-keenetic-kap-630
+ ZYIMAGE_ID := 0x810630
+ $(call Device/keenetic_kap-630-common)
+endef
+TARGET_DEVICES += keenetic_kap-630
+
define Device/keenetic_kn-1812-common
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7992-firmware kmod-usb3 \
@@ -2228,6 +2254,15 @@ define Device/netcore_n60-pro
endef
TARGET_DEVICES += netcore_n60-pro
+define Device/netcraze_nap-630
+ DEVICE_VENDOR := Netcraze
+ DEVICE_MODEL := NAP-630
+ DEVICE_DTS := mt7981b-netcraze-nap-630
+ ZYIMAGE_ID := 0xC10630
+ $(call Device/keenetic_kap-630-common)
+endef
+TARGET_DEVICES += netcraze_nap-630
+
define Device/netcraze_nc-1812
DEVICE_VENDOR := Netcraze
DEVICE_MODEL := NC-1812
More information about the lede-commits
mailing list