[openwrt/openwrt] mediatek: filogic: add support for Cudy WR3000P v1
LEDE Commits
lede-commits at lists.infradead.org
Sun Sep 7 05:47:04 PDT 2025
hauke pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/04e9d154f209c0390d962c10e75ed3c49bd5a9e9
commit 04e9d154f209c0390d962c10e75ed3c49bd5a9e9
Author: Michal Halva <hedik01 at gmail.com>
AuthorDate: Sat Aug 2 20:46:14 2025 +0200
mediatek: filogic: add support for Cudy WR3000P v1
Hardware
--------
MediaTek MT7981 WiSoC
512MB DDR4 RAM
128MB SPI-NAND
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
4 LAN MediaTek MT7531 PHY
1 WAN RTL8221B-VB-CG 2.5Gbps PHY
UART: 115200 8N1 3.3V
USB2 Port
PoE on WAN Port
MAC:
LAN MAC: label mac
WAN MAC: label mac + 1
2.4G MAC: label mac
5G MAC: label mac + 1 with LA bit set
Gotchas:
WAN LED does not light up (might require further DTS tweaks)
PoE on WAN port was not tested
This commit is heavily based on WR3000H one, I've just ported DTS differences
from the official image to get USB support and proper LED mapping.
Installation
------------
[Untested as I've received and used a transitional image from Cudy]
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device + press reset pin. Keep pressing reset pin to enter the U-Boot shell.
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.88. Rename the image to "cudy3000p.bin"
4. Download and boot the OpenWrt initramfs image.
$ tftpboot 0x46000000 cudy3000s.bin; bootm 0x46000000
5. Transfer the OpenWrt sysupgrade image to the device using scp.
Install with sysupgrade.
Signed-off-by: Michal Halva <hedik01 at gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19636
Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
---
.../linux/mediatek/dts/mt7981b-cudy-wr3000p-v1.dts | 153 +++++++++++++++++++++
.../filogic/base-files/etc/board.d/01_leds | 3 +-
.../etc/hotplug.d/ieee80211/11_fix_wifi_mac | 1 +
.../filogic/base-files/lib/upgrade/platform.sh | 3 +-
target/linux/mediatek/image/filogic.mk | 17 +++
5 files changed, 175 insertions(+), 2 deletions(-)
diff --git a/target/linux/mediatek/dts/mt7981b-cudy-wr3000p-v1.dts b/target/linux/mediatek/dts/mt7981b-cudy-wr3000p-v1.dts
new file mode 100644
index 0000000000..0bee64d7b8
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7981b-cudy-wr3000p-v1.dts
@@ -0,0 +1,153 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+/dts-v1/;
+
+#include "mt7981b-cudy-wr3000-nand.dtsi"
+
+/ {
+ model = "Cudy WR3000P v1";
+ compatible = "cudy,wr3000p-v1", "mediatek,mt7981";
+
+ aliases {
+ label-mac-device = &gmac0;
+ led-boot = &led_status;
+ led-failsafe = &led_status;
+ led-running = &led_status;
+ led-upgrade = &led_status;
+ serial0 = &uart0;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_status: led-status {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 11 GPIO_ACTIVE_LOW>;
+ };
+
+ led-internet {
+ function = LED_FUNCTION_WAN_ONLINE;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 6 GPIO_ACTIVE_LOW>;
+ };
+
+ led-wlan2g {
+ function = LED_FUNCTION_WLAN_2GHZ;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 7 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ led-wlan5g {
+ function = LED_FUNCTION_WLAN_5GHZ;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ led-wan {
+ function = LED_FUNCTION_WAN;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 5 GPIO_ACTIVE_LOW>;
+ };
+
+ led-usb {
+ function = LED_FUNCTION_USB;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 4 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ usb_vbus: regulator-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+ regulator-boot-on;
+ };
+};
+
+ð {
+ gmac1: mac at 1 {
+ compatible = "mediatek,eth-mac";
+ reg = <1>;
+ phy-handle = <&phy6>;
+ phy-mode = "2500base-x";
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&macaddr_bdinfo_de00 1>;
+ label = "wan";
+ };
+};
+
+&mdio_bus {
+ phy6: ethernet-phy at 6 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <6>;
+ reset-assert-us = <100000>;
+ reset-deassert-us = <100000>;
+ reset-gpios = <&pio 3 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&switch {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ label = "lan4";
+ };
+
+ port at 1 {
+ reg = <1>;
+ label = "lan3";
+ };
+
+ port at 2 {
+ reg = <2>;
+ label = "lan2";
+ };
+
+ port at 3 {
+ reg = <3>;
+ label = "lan1";
+ };
+
+ port at 6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+};
+
+&xhci {
+ vusb33-supply = <®_3p3v>;
+ vbus-supply = <&usb_vbus>;
+ mediatek,u3p-dis-msk = <0x01>;
+ phys = <&u2port0 PHY_TYPE_USB2>;
+ status = "okay";
+};
+
+&usb_phy {
+ status = "okay";
+};
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
index b590ddb7e0..0fe1dfc351 100644
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
@@ -59,7 +59,8 @@ wavlink,wl-wn573hx3)
cudy,wr3000-v1)
ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan"
;;
-cudy,wr3000h-v1)
+cudy,wr3000h-v1|\
+cudy,wr3000p-v1)
ucidef_set_led_netdev "lan1" "lan1" "white:lan-1" "lan1" "link tx rx"
ucidef_set_led_netdev "lan2" "lan2" "white:lan-2" "lan2" "link tx rx"
ucidef_set_led_netdev "lan3" "lan3" "white:lan-3" "lan3" "link tx rx"
diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
index e54056d165..c26ccf1d28 100644
--- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
+++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
@@ -90,6 +90,7 @@ case "$board" in
cudy,wr3000e-v1|\
cudy,wr3000s-v1|\
cudy,wr3000h-v1|\
+ cudy,wr3000p-v1|\
cudy,wr3000-v1)
addr=$(mtd_get_mac_binary bdinfo 0xde00)
# Originally, phy0 is phy1 mac with LA bit set. However, this would conflict
diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
index a29ad2a6f6..8f9515e304 100755
--- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
+++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
@@ -131,7 +131,8 @@ platform_do_upgrade() {
CI_KERNPART="linux"
nand_do_upgrade "$1"
;;
- cudy,wr3000h-v1)
+ cudy,wr3000h-v1|\
+ cudy,wr3000p-v1)
CI_UBIPART="ubi"
nand_do_upgrade "$1"
;;
diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk
index 0e3103cd6b..bc2b5bba8f 100644
--- a/target/linux/mediatek/image/filogic.mk
+++ b/target/linux/mediatek/image/filogic.mk
@@ -969,6 +969,23 @@ define Device/cudy_wr3000h-v1
endef
TARGET_DEVICES += cudy_wr3000h-v1
+define Device/cudy_wr3000p-v1
+ DEVICE_VENDOR := Cudy
+ DEVICE_MODEL := WR3000P
+ DEVICE_VARIANT := v1
+ DEVICE_DTS := mt7981b-cudy-wr3000p-v1
+ DEVICE_DTS_DIR := ../dts
+ SUPPORTED_DEVICES += R57
+ UBINIZE_OPTS := -E 5
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ IMAGE_SIZE := 65536k
+ KERNEL_IN_UBI := 1
+ IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+ DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware
+endef
+TARGET_DEVICES += cudy_wr3000p-v1
+
define Device/dlink_aquila-pro-ai-m30-a1
DEVICE_VENDOR := D-Link
DEVICE_MODEL := AQUILA PRO AI M30
More information about the lede-commits
mailing list