[openwrt/openwrt] ramips: add support for Cudy C200P
LEDE Commits
lede-commits at lists.infradead.org
Tue Oct 7 16:00:55 PDT 2025
hauke pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/2b7fffa963bb2d45a0d13e75cb882308937a61d5
commit 2b7fffa963bb2d45a0d13e75cb882308937a61d5
Author: Marcin Leksmark <lexmark3200 at wp.pl>
AuthorDate: Tue Sep 23 18:37:25 2025 +0200
ramips: add support for Cudy C200P
This patch adds support for Cudy C200P.
Specifications:
SoC: MediaTek MT7621AT
RAM: 256 MB (DDR3)
Flash: 16 MB (NOR)
POE Chip: IP804AR
Interfaces:
Switch: 1 WAN, 4 LAN (Gigabit)
Gigabit RJ45 PoE Ports on 2~5
Max Power on a Single PoE Ports 30W
PoE Ports : The PoE ports comply with IEEE 802.3at/af standards.
Ports: 1 USB-A 3.0 Ports
LED:
System
PoE Max Status
Link/ACT/PoE Status of Each PoE Port
Physical Buttons:
Reset Button
Power Input:
DC Jack
Power Methods:
DC: 54V 1.11A
802.3at/af PoE
Passive PoE: 24/48V
Max Power Consumption (W):
Total: 60W
PoE: 55W
PoE (when USB Device is plugged in): 50W
No PoE: 5W
Installation:
To install OpenWRT, you need the intermediate firmware from Cudy. (U-boot is locked). After installing the intermediate firmware, you can install OpenWRT via sysupgrade.
Recovery:
TFTP available.
1. Place the recovery.bin in the serving directory of your TFTP server.
2. Set your IP to 192.168.1.88/24.
3. Press the “Reset” button of Cudy router and hold it. Before the Cudy router is powered on and before TFTP start to download the firmware, don't release the “Reset” button.
4. Power on the Cudy router.
5. You can release the reset button only when TFTP starts downloading firmware.
6. When the SYSTEM LED turns solid green, the upgrade is complete.
Serial:
1. Serial connection parameters: 115200 / 8N1
2. Serial connection voltage: 3.3V
PoE is not supported at the time of PR. The IP804R chip is not yet supported by OpenWRT.
Signed-off-by: Marcin Leksmark <lexmark3200 at wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20165
Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
---
target/linux/ramips/dts/mt7621_cudy_c200p.dts | 185 +++++++++++++++++++++
target/linux/ramips/image/mt7621.mk | 10 ++
.../mt7621/base-files/etc/board.d/02_network | 7 +-
3 files changed, 199 insertions(+), 3 deletions(-)
diff --git a/target/linux/ramips/dts/mt7621_cudy_c200p.dts b/target/linux/ramips/dts/mt7621_cudy_c200p.dts
new file mode 100644
index 0000000000..fc85202560
--- /dev/null
+++ b/target/linux/ramips/dts/mt7621_cudy_c200p.dts
@@ -0,0 +1,185 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ compatible = "cudy,c200p", "mediatek,mt7621-soc";
+ model = "Cudy C200P";
+
+ aliases {
+ led-boot = &led_status_green;
+ led-failsafe = &led_status_green;
+ led-running = &led_status_green;
+ label-mac-device = &gmac0;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ watchdog {
+ compatible = "linux,wdt-gpio";
+ gpios = <&gpio 10 GPIO_ACTIVE_HIGH>;
+ hw_algo = "toggle";
+ hw_margin_ms = <1000>;
+ always-running;
+ };
+
+ gpio-export {
+ compatible = "gpio-export";
+ #size-cells = <0>;
+
+ pse {
+ gpio-export,name = "pse";
+ gpio-export,output = <1>;
+ gpios = <&gpio 14 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_status_green: led-status-green {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ };
+
+ led-poe-green {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_INDICATOR;
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+®_vbus {
+ /delete-property/ regulator-always-on;
+ gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+};
+
+&i2c {
+ status = "okay";
+};
+
+&gmac0 {
+ nvmem-cells = <&macaddr_bdinfo_de00 0>;
+ nvmem-cell-names = "mac-address";
+};
+
+&spi0 {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition at 30000 {
+ label = "u-boot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition at 50000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x50000 0xfa0000>;
+ };
+
+ partition at ff0000 {
+ label = "bdinfo";
+ reg = <0xff0000 0x10000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_bdinfo_de00: macaddr at de00 {
+ compatible = "mac-base";
+ reg = <0xde00 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&state_default {
+ gpio {
+ groups = "jtag", "uart2", "uart3", "wdt";
+ function = "gpio";
+ };
+};
+
+&gmac1 {
+ status = "okay";
+ label = "wan";
+ phy-handle = <ðphy4>;
+
+ nvmem-cells = <&macaddr_bdinfo_de00 1>;
+ nvmem-cell-names = "mac-address";
+};
+
+ðphy4 {
+ /delete-property/ interrupts;
+};
+
+&switch0 {
+ ports {
+ port at 0 {
+ status = "okay";
+ label = "lan5";
+ };
+
+ port at 1 {
+ status = "okay";
+ label = "lan4";
+ };
+
+ port at 2 {
+ status = "okay";
+ label = "lan3";
+ };
+
+ port at 3 {
+ status = "okay";
+ label = "lan2";
+ };
+ };
+};
diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk
index b8a7d2d220..ac7ca0bd58 100644
--- a/target/linux/ramips/image/mt7621.mk
+++ b/target/linux/ramips/image/mt7621.mk
@@ -806,6 +806,16 @@ define Device/cudy_r700
endef
TARGET_DEVICES += cudy_r700
+define Device/cudy_c200p
+ $(Device/dsa-migration)
+ DEVICE_VENDOR := Cudy
+ DEVICE_MODEL := C200P
+ IMAGE_SIZE := 15872k
+ UIMAGE_NAME := R74
+ DEVICE_PACKAGES := -uboot-envtools -wpad-basic-mbedtls kmod-usb3
+endef
+TARGET_DEVICES += cudy_c200p
+
define Device/cudy_x6-v1
$(Device/dsa-migration)
IMAGE_SIZE := 32256k
diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network
index 81fea421c7..202cac598a 100644
--- a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network
@@ -119,6 +119,10 @@ ramips_setup_interfaces()
uci add_list firewall. at zone[1].network='eth_data'
uci add_list firewall. at zone[1].network='eth_om'
;;
+ cudy,c200p|\
+ mikrotik,routerboard-750gr3)
+ ucidef_set_interfaces_lan_wan "lan2 lan3 lan4 lan5" "wan"
+ ;;
dlink,covr-x1860-a1)
ucidef_set_interfaces_lan_wan "ethernet" "internet"
;;
@@ -137,9 +141,6 @@ ramips_setup_interfaces()
gnubee,gb-pc2)
ucidef_set_interface_lan "ethblack ethblue ethyellow"
;;
- mikrotik,routerboard-750gr3)
- ucidef_set_interfaces_lan_wan "lan2 lan3 lan4 lan5" "wan"
- ;;
mikrotik,routerboard-760igs)
ucidef_set_interfaces_lan_wan "lan2 lan3 lan4 lan5" "wan sfp"
;;
More information about the lede-commits
mailing list