[openwrt/openwrt] ipq40xx: add support for Netgear RBR20
LEDE Commits
lede-commits at lists.infradead.org
Sat Nov 15 02:24:53 PST 2025
robimarko pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/251d551fa6be3d367086abb8a7f6413384cc4775
commit 251d551fa6be3d367086abb8a7f6413384cc4775
Author: Christoph Krapp <achterin at gmail.com>
AuthorDate: Thu Oct 23 09:10:31 2025 +0200
ipq40xx: add support for Netgear RBR20
This device shares a lot of similarities with the LBR20 - the RBR20 just
misses the LTE modem and its formfactor is alot smaller. Other than that
the LED configuration matches other RBR devices but the RBR20 has less
LEDs than its larger counterparts.
Hardware
--------
SOC: Qualcomm IPQ4019
FLASH: 256MB (Winbond W29N02GVSIAF)
RAM: 512MB (Nanya NT5CC256M16EP-EK)
WIFI: Qualcomm IPQ4019
Qualcomm Atheros QCA9886
ETH: 1x WAN, 1x LAN
LED: 5 (4 RGB at top, 1 RG at back)
BTN: WPS, Reset
UART: 115200 8N1 (dotted Pin = VCC) VCC-TX-RX-GND
MAC addresses
-------------
LAN Label MAC (stored in boarddata1 offset 0x0)
WAN LAN + 1 (stored in boarddata1 offset 0x6)
2.4G LAN
5GLow LAN + 3 (stored in boarddata1 offset 0xc)
5GUpper LAN + 2 (stored in boarddata1 offset 0x12)
Installation
------------
Either use the vendor ui upgrade method or nmrpflash to install the
factory image.
Signed-off-by: Christoph Krapp <achterin at gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20560
Signed-off-by: Robert Marko <robimarko at gmail.com>
---
.../boot/uboot-tools/uboot-envtools/files/ipq40xx | 3 +-
package/firmware/ipq-wifi/Makefile | 2 +
.../ipq40xx/base-files/etc/board.d/02_network | 1 +
.../ipq40xx/base-files/lib/upgrade/platform.sh | 1 +
.../arch/arm/boot/dts/qcom/qcom-ipq4019-rbr20.dts | 489 +++++++++++++++++++++
target/linux/ipq40xx/image/generic.mk | 21 +
6 files changed, 516 insertions(+), 1 deletion(-)
diff --git a/package/boot/uboot-tools/uboot-envtools/files/ipq40xx b/package/boot/uboot-tools/uboot-envtools/files/ipq40xx
index 717158b042..b3d18980d5 100644
--- a/package/boot/uboot-tools/uboot-envtools/files/ipq40xx
+++ b/package/boot/uboot-tools/uboot-envtools/files/ipq40xx
@@ -54,7 +54,8 @@ aruba,ap-365)
ubootenv_add_uci_config "/dev/mtd8" "0x0" "0x10000" "0x10000"
;;
buffalo,wtr-m2133hp|\
-netgear,lbr20)
+netgear,lbr20|\
+netgear,rbr20)
ubootenv_add_uci_config "/dev/mtd8" "0x0" "0x40000" "0x20000"
;;
linksys,ea6350v3)
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile
index 2c7bf397a0..6ba5cc6037 100644
--- a/package/firmware/ipq-wifi/Makefile
+++ b/package/firmware/ipq-wifi/Makefile
@@ -61,6 +61,7 @@ ALLWIFIBOARDS:= \
meraki_z3 \
netgear_lbr20 \
netgear_rax120v2 \
+ netgear_rbk20 \
netgear_sxk80 \
netgear_wax214 \
netgear_wax218 \
@@ -237,6 +238,7 @@ $(eval $(call generate-ipq-wifi-package,meraki_mr30h,Meraki MR30H))
$(eval $(call generate-ipq-wifi-package,meraki_z3,Meraki Z3))
$(eval $(call generate-ipq-wifi-package,netgear_lbr20,Netgear LBR20))
$(eval $(call generate-ipq-wifi-package,netgear_rax120v2,Netgear RAX120v2))
+$(eval $(call generate-ipq-wifi-package,netgear_rbk20,Netgear RBK20))
$(eval $(call generate-ipq-wifi-package,netgear_sxk80,Netgear SXK80))
$(eval $(call generate-ipq-wifi-package,netgear_wax214,Netgear WAX214))
$(eval $(call generate-ipq-wifi-package,netgear_wax218,Netgear WAX218))
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 727165870c..737fcee083 100644
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -42,6 +42,7 @@ ipq40xx_setup_interfaces()
linksys,whw03v2|\
luma,wrtq-329acn|\
mikrotik,cap-ac|\
+ netgear,rbr20|\
netgear,wac510|\
sony,ncp-hg100-cellular|\
wallys,dr40x9|\
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index 58108fce73..248832d467 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -123,6 +123,7 @@ platform_do_upgrade() {
luma,wrtq-329acn|\
mobipromo,cm520-79f|\
netgear,lbr20|\
+ netgear,rbr20|\
netgear,wac510|\
p2w,r619ac-64m|\
p2w,r619ac-128m|\
diff --git a/target/linux/ipq40xx/files-6.12/arch/arm/boot/dts/qcom/qcom-ipq4019-rbr20.dts b/target/linux/ipq40xx/files-6.12/arch/arm/boot/dts/qcom/qcom-ipq4019-rbr20.dts
new file mode 100644
index 0000000000..269be9fdfb
--- /dev/null
+++ b/target/linux/ipq40xx/files-6.12/arch/arm/boot/dts/qcom/qcom-ipq4019-rbr20.dts
@@ -0,0 +1,489 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Netgear RBR20";
+ compatible = "netgear,rbr20";
+
+ chosen {
+ bootargs-append = "ubi.mtd=ubi root=/dev/ubiblock0_0";
+ };
+
+ aliases {
+ led-boot = &led_status_white;
+ led-failsafe = &led_status_red;
+ led-running = &led_status_green;
+ led-upgrade = &led_status_blue;
+ label-mac-device = &gmac;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&tlmm 22 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ led-1 {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&tlmm 23 GPIO_ACTIVE_HIGH>;
+ panic-indicator;
+ };
+
+ led_status_green: led-2 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&tlmm 24 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_status_red: led-3 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_status_blue: led-4 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_status_white: led-5 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&tlmm 27 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ soc {
+ tcsr at 1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr at 194b000 {
+ status = "okay";
+
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ };
+
+ ess_tcsr at 1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr at 1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+ };
+};
+
+&prng {
+ status = "okay";
+};
+
+&mdio {
+ status = "okay";
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+};
+
+&crypto {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&tlmm {
+ mdio_pins: mdio-pinmux {
+ mux_mdio {
+ pins = "gpio6";
+ function = "mdio";
+ bias-pull-up;
+ };
+
+ mux_mdc {
+ pins = "gpio7";
+ function = "mdc";
+ bias-pull-up;
+ };
+ };
+
+ serial_pins: serial-pinmux {
+ function = "blsp_uart0";
+ pins = "gpio16", "gpio17";
+ bias-disable;
+ };
+
+ nand_pins: nand-pins {
+ pullups {
+ pins = "gpio53", "gpio58", "gpio59";
+ function = "qpic";
+ bias-pull-up;
+ };
+
+ pulldowns {
+ pins = "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio60", "gpio61",
+ "gpio62", "gpio63", "gpio64",
+ "gpio65", "gpio66", "gpio67",
+ "gpio68", "gpio69";
+ function = "qpic";
+ bias-pull-down;
+ };
+ };
+};
+
+&nand {
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ nand at 0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "0:SBL1";
+ reg = <0x00000000 0x00100000>;
+ read-only;
+ };
+
+ partition at 100000 {
+ label = "0:MIBIB";
+ reg = <0x00100000 0x00100000>;
+ read-only;
+ };
+
+ partition at 200000 {
+ label = "0:BOOTCONFIG";
+ reg = <0x00200000 0x00100000>;
+ read-only;
+ };
+
+ partition at 300000 {
+ label = "0:QSEE";
+ reg = <0x00300000 0x00100000>;
+ read-only;
+ };
+
+ partition at 400000 {
+ label = "0:QSEE_1";
+ reg = <0x00400000 0x00100000>;
+ read-only;
+ };
+
+ partition at 500000 {
+ label = "0:CDT";
+ reg = <0x00500000 0x00080000>;
+ read-only;
+ };
+
+ partition at 580000 {
+ label = "0:CDT_1";
+ reg = <0x00580000 0x00080000>;
+ read-only;
+ };
+
+ partition at 600000 {
+ label = "0:BOOTCONFIG1";
+ reg = <0x00600000 0x00080000>;
+ read-only;
+ };
+
+ partition at 680000 {
+ label = "0:APPSBLENV";
+ reg = <0x00680000 0x00080000>;
+ };
+
+ partition at 700000 {
+ label = "0:APPSBL";
+ reg = <0x00700000 0x00200000>;
+ read-only;
+ };
+
+ partition at 900000 {
+ label = "0:APPSBL_1";
+ reg = <0x00900000 0x00200000>;
+ read-only;
+ };
+
+ partition at b00000 {
+ label = "0:ART";
+ reg = <0x00b00000 0x00080000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ precal_art_1000: precal at 1000 {
+ reg = <0x1000 0x2f20>;
+ };
+
+ precal_art_5000: precal at 5000 {
+ reg = <0x5000 0x2f20>;
+ };
+
+ precal_art_9000: precal at 9000 {
+ reg = <0x9000 0x2f20>;
+ };
+ };
+ };
+
+ partition at b80000 {
+ label = "0:ART.bak";
+ reg = <0x00b80000 0x00080000>;
+ read-only;
+ };
+
+ partition at c00000 {
+ label = "config";
+ reg = <0x00c00000 0x00100000>;
+ read-only;
+ };
+
+ partition at d00000 {
+ label = "boarddata1";
+ reg = <0x00d00000 0x00080000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ mac_address_lan: macaddr at 0 {
+ compatible = "mac-base";
+ reg = <0x0 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ mac_address_wan: macaddr at 6 {
+ compatible = "mac-base";
+ reg = <0x6 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ mac_address_wlan_5g: macaddr at c {
+ compatible = "mac-base";
+ reg = <0xc 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ mac_address_wlan_2nd5g: macaddr at 12 {
+ compatible = "mac-base";
+ reg = <0x12 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+ };
+ };
+
+ partition at d80000 {
+ label = "boarddata2";
+ reg = <0x00d80000 0x00040000>;
+ read-only;
+ };
+
+ partition at dc0000 {
+ label = "pot";
+ reg = <0x00dc0000 0x00100000>;
+ read-only;
+ };
+
+ partition at ec0000 {
+ label = "boarddata1.bak";
+ reg = <0x00ec0000 0x00080000>;
+ read-only;
+ };
+
+ partition at f40000 {
+ label = "boarddata2.bak";
+ reg = <0x00f40000 0x00040000>;
+ read-only;
+ };
+
+ partition at f80000 {
+ label = "language";
+ reg = <0x00f80000 0x00300000>;
+ read-only;
+ };
+
+ partition at 1280000 {
+ label = "cert";
+ reg = <0x01280000 0x00080000>;
+ read-only;
+ };
+
+ partition at 1300000 {
+ label = "ntgrdata";
+ reg = <0x01300000 0x09300000>;
+ };
+
+ partition at a600000 {
+ label = "kernel";
+ reg = <0x0a600000 0x00700000>;
+ };
+
+ partition at ad00000 {
+ label = "ubi";
+ reg = <0x0ad00000 0x05300000>;
+ };
+ };
+ };
+};
+
+&blsp1_i2c3 {
+ status = "okay";
+
+ led-controller at 27 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "ti,tlc59108"; /* really is tlc59208f */
+ reg = <0x27>;
+
+ led0 at 0 {
+ function = LED_FUNCTION_BACKLIGHT;
+ function-enumerator = <0>;
+ color = <LED_COLOR_ID_WHITE>;
+ reg = <0x0>;
+ linux,default-trigger = "default-on";
+ };
+
+ led1 at 1 {
+ function = LED_FUNCTION_BACKLIGHT;
+ function-enumerator = <1>;
+ color = <LED_COLOR_ID_WHITE>;
+ reg = <0x1>;
+ linux,default-trigger = "default-on";
+ };
+
+ led2 at 2 {
+ function = LED_FUNCTION_BACKLIGHT;
+ function-enumerator = <2>;
+ color = <LED_COLOR_ID_WHITE>;
+ reg = <0x2>;
+ linux,default-trigger = "default-on";
+ };
+
+ led3 at 3 {
+ function = LED_FUNCTION_BACKLIGHT;
+ function-enumerator = <3>;
+ color = <LED_COLOR_ID_WHITE>;
+ reg = <0x3>;
+ linux,default-trigger = "default-on";
+ };
+ };
+};
+
+&blsp1_uart1 {
+ status = "okay";
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&gmac {
+ status = "okay";
+
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&mac_address_lan 0>;
+};
+
+&switch {
+ status = "okay";
+};
+
+&swport4 {
+ status = "okay";
+
+ label = "wan";
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&mac_address_wan 0>;
+};
+
+&swport5 {
+ status = "okay";
+
+ label = "lan";
+};
+
+&pcie0 {
+ status = "okay";
+
+ perst-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
+};
+
+&pcie_bridge0 {
+ wifi at 0,0 {
+ compatible = "qcom,ath10k";
+ reg = <0x00010000 0 0 0 0>;
+ ieee80211-freq-limit = <5170000 5350000>;
+ nvmem-cell-names = "pre-calibration", "mac-address";
+ nvmem-cells = <&precal_art_9000>, <&mac_address_wlan_2nd5g 0>;
+ qcom,ath10k-calibration-variant = "Netgear-RBK20";
+ };
+};
+
+&wifi0 {
+ status = "okay";
+ nvmem-cell-names = "pre-calibration", "mac-address";
+ nvmem-cells = <&precal_art_1000>, <&mac_address_lan 0>;
+ qcom,ath10k-calibration-variant = "Netgear-RBK20";
+};
+
+&wifi1 {
+ status = "okay";
+ ieee80211-freq-limit = <5470000 5815000>;
+ nvmem-cell-names = "pre-calibration", "mac-address";
+ nvmem-cells = <&precal_art_5000>, <&mac_address_wlan_5g 0>;
+ qcom,ath10k-calibration-variant = "Netgear-RBK20";
+};
diff --git a/target/linux/ipq40xx/image/generic.mk b/target/linux/ipq40xx/image/generic.mk
index 8961d7faf7..af637c4ba3 100644
--- a/target/linux/ipq40xx/image/generic.mk
+++ b/target/linux/ipq40xx/image/generic.mk
@@ -911,6 +911,27 @@ define Device/netgear_lbr20
endef
TARGET_DEVICES += netgear_lbr20
+define Device/netgear_rbr20
+ $(call Device/DniImage)
+ SOC := qcom-ipq4019
+ DEVICE_VENDOR := NETGEAR
+ DEVICE_MODEL := RBR20
+ NETGEAR_BOARD_ID := RBR20
+ NETGEAR_HW_ID := 29765641+0+256+512+2x2+2x2+2x2
+ KERNEL_SIZE := 7340032
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ UBINIZE_OPTS := -E 5
+ IMAGE/factory.img := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | \
+ append-uImage-fakehdr filesystem | pad-to $$$$(KERNEL_SIZE) | \
+ append-ubi | netgear-dni
+ IMAGE/sysupgrade.bin := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | \
+ append-uImage-fakehdr filesystem | sysupgrade-tar kernel=$$$$@ | \
+ append-metadata
+ DEVICE_PACKAGES := ipq-wifi-netgear_rbk20 ath10k-firmware-qca9888-ct
+endef
+TARGET_DEVICES += netgear_rbr20
+
define Device/netgear_rbx40
$(call Device/netgear_orbi)
NETGEAR_HW_ID := 29765515+0+4096+512+2x2+2x2+2x2
More information about the lede-commits
mailing list