[openwrt/openwrt] qualcommax: 6.12: drop upstreamed patches
LEDE Commits
lede-commits at lists.infradead.org
Fri May 16 08:57:48 PDT 2025
robimarko pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/dbf9c83e7a8fb7d0ba348949459a5bac9632cb1a
commit dbf9c83e7a8fb7d0ba348949459a5bac9632cb1a
Author: Robert Marko <robimarko at gmail.com>
AuthorDate: Fri May 9 11:55:27 2025 +0200
qualcommax: 6.12: drop upstreamed patches
Drop patches that are already present in kernel 6.12.
Link: https://github.com/openwrt/openwrt/pull/18795
Signed-off-by: Robert Marko <robimarko at gmail.com>
---
...s-arm-qcom-ids-Add-IDs-for-IPQ8174-family.patch | 29 --
...pufreq-qcom-nvmem-add-support-for-IPQ6018.patch | 123 -------
...pufreq-qcom-nvmem-add-support-for-IPQ8074.patch | 113 ------
...ss-ipq6018-add-the-GPLL0-clock-also-as-cl.patch | 43 ---
...com-ipq8074-include-the-GPLL0-as-clock-pr.patch | 32 --
...m64-dts-qcom-ipq6018-include-the-GPLL0-as.patch | 35 --
...7-clk-qcom-gcc-ipq6018-add-QUP6-I2C-clock.patch | 57 ---
...-arm64-dts-qcom-ipq6018-use-CPUFreq-NVMEM.patch | 85 -----
...4-dts-ipq6018-Add-remaining-QUP-UART-node.patch | 81 -----
...dts-qcom-Fix-hs_phy_irq-for-QUSB2-targets.patch | 95 -----
...pinlock-qcom-Remove-IPQ6018-SOC-specific-.patch | 32 --
...6.9-arm64-dts-qcom-ipq6018-add-tsens-node.patch | 34 --
...-arm64-dts-qcom-ipq6018-add-thermal-zones.patch | 180 ----------
...c-ipq6018-add-qdss_at-clock-needed-for-wi.patch | 50 ---
...-usb-fix-serdes-init-sequence-for-IPQ6018.patch | 58 ---
...-arm64-dts-qcom-ipq8074-Add-QUP4-SPI-node.patch | 38 --
...com-ipq8074-Remove-unused-gpio-from-QPIC-.patch | 32 --
...-v6.7-arm64-dts-qcom-ipq5018-add-watchdog.patch | 31 --
...-scm-support-indicating-SDI-default-state.patch | 41 ---
...firmware-qcom-scm-disable-SDI-if-required.patch | 83 -----
...ings-qcom-scm-document-IPQ5018-compatible.patch | 25 --
...Q5018-indicate-that-SDI-shoud-be-disabled.patch | 26 --
...dings-phy-qcom-m31-Add-IPQ5018-compatible.patch | 28 --
...-compatible-phy-init-sequence-for-IPQ5018.patch | 89 -----
...-bindings-usb-dwc3-Add-IPQ5018-compatible.patch | 41 ---
...64-dts-qcom-ipq5018-Add-USB-related-nodes.patch | 86 -----
...-dts-qcom-ipq5018-add-QUP1-SPI-controller.patch | 56 ---
...-clock-qcom-a53pll-add-IPQ5018-compatible.patch | 25 --
...qcom-apss-ipq-pll-add-support-for-IPQ5018.patch | 62 ----
...s-qcom-ipq5018-enable-the-CPUFreq-support.patch | 98 ------
...5018-add-few-more-reserved-memory-regions.patch | 66 ----
...romer-ops-for-IPQ5018-to-fix-boot-failure.patch | 83 -----
...com-apss-ipq-pll-fix-PLL-rate-for-IPQ5018.patch | 32 --
...c-ipq6018-update-sdcc-max-clock-frequency.patch | 26 --
....11-arm64-dts-qcom-ipq6018-add-sdhci-node.patch | 47 ---
...k-rcg-introduce-support-for-multiple-conf.patch | 83 -----
...k-rcg2-add-support-for-rcg2-freq-multi-op.patch | 296 ----------------
...c-ipq8074-rework-nss_port5-6-clock-to-mul.patch | 227 ------------
...com-ipq8074-switch-PCIe-QMP-PHY-to-new-st.patch | 122 -------
...com-ipq8074-pass-QMP-PCI-PHY-PIPE-clocks-.patch | 39 ---
...11-PCI-qcom-Use-devm_clk_bulk_get_all-API.patch | 388 ---------------------
...m64-dts-qcom-ipq8074-Add-PCIe-bridge-node.patch | 52 ---
...m64-dts-qcom-ipq6018-Add-PCIe-bridge-node.patch | 35 --
43 files changed, 3304 deletions(-)
diff --git a/target/linux/qualcommax/patches-6.12/0001-v6.7-dt-bindings-arm-qcom-ids-Add-IDs-for-IPQ8174-family.patch b/target/linux/qualcommax/patches-6.12/0001-v6.7-dt-bindings-arm-qcom-ids-Add-IDs-for-IPQ8174-family.patch
deleted file mode 100644
index c1381a7bf3..0000000000
--- a/target/linux/qualcommax/patches-6.12/0001-v6.7-dt-bindings-arm-qcom-ids-Add-IDs-for-IPQ8174-family.patch
+++ /dev/null
@@ -1,29 +0,0 @@
-From 93e161c8f4b9b051e5e746814138cb5520b4b897 Mon Sep 17 00:00:00 2001
-From: Robert Marko <robimarko at gmail.com>
-Date: Fri, 1 Sep 2023 20:10:04 +0200
-Subject: [PATCH] dt-bindings: arm: qcom,ids: Add IDs for IPQ8174 family
-
-IPQ8174 (Oak) family is part of the IPQ8074 family, but the ID-s for it
-are missing so lets add them.
-
-Signed-off-by: Robert Marko <robimarko at gmail.com>
-Reviewed-by: Kathiravan T <quic_kathirav at quicinc.com>
-Acked-by: Conor Dooley <conor.dooley at microchip.com>
-Link: https://lore.kernel.org/r/20230901181041.1538999-1-robimarko@gmail.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- include/dt-bindings/arm/qcom,ids.h | 3 +++
- 1 file changed, 3 insertions(+)
-
---- a/include/dt-bindings/arm/qcom,ids.h
-+++ b/include/dt-bindings/arm/qcom,ids.h
-@@ -203,6 +203,9 @@
- #define QCOM_ID_SM6125 394
- #define QCOM_ID_IPQ8070A 395
- #define QCOM_ID_IPQ8071A 396
-+#define QCOM_ID_IPQ8172 397
-+#define QCOM_ID_IPQ8173 398
-+#define QCOM_ID_IPQ8174 399
- #define QCOM_ID_IPQ6018 402
- #define QCOM_ID_IPQ6028 403
- #define QCOM_ID_SDM429W 416
diff --git a/target/linux/qualcommax/patches-6.12/0002-v6.7-cpufreq-qcom-nvmem-add-support-for-IPQ6018.patch b/target/linux/qualcommax/patches-6.12/0002-v6.7-cpufreq-qcom-nvmem-add-support-for-IPQ6018.patch
deleted file mode 100644
index 95c6c9505d..0000000000
--- a/target/linux/qualcommax/patches-6.12/0002-v6.7-cpufreq-qcom-nvmem-add-support-for-IPQ6018.patch
+++ /dev/null
@@ -1,123 +0,0 @@
-From 47e161a7873b0891f4e01a69a839f6161d816ea8 Mon Sep 17 00:00:00 2001
-From: Robert Marko <robimarko at gmail.com>
-Date: Wed, 25 Oct 2023 14:57:57 +0530
-Subject: [PATCH] cpufreq: qcom-nvmem: add support for IPQ6018
-
-IPQ6018 SoC series comes in multiple SKU-s, and not all of them support
-high frequency OPP points.
-
-SoC itself does however have a single bit in QFPROM to indicate the CPU
-speed-bin.
-That bit is used to indicate frequency limit of 1.5GHz, but that alone is
-not enough as IPQ6000 only goes up to 1.2GHz, but SMEM ID can be used to
-limit it further.
-
-IPQ6018 compatible is blacklisted from DT platdev as the cpufreq device
-will get created by NVMEM CPUFreq driver.
-
-Signed-off-by: Robert Marko <robimarko at gmail.com>
-[ Viresh: Fixed rebase conflict. ]
-Signed-off-by: Viresh Kumar <viresh.kumar at linaro.org>
----
- drivers/cpufreq/cpufreq-dt-platdev.c | 1 +
- drivers/cpufreq/qcom-cpufreq-nvmem.c | 58 ++++++++++++++++++++++++++++
- 2 files changed, 59 insertions(+)
-
---- a/drivers/cpufreq/cpufreq-dt-platdev.c
-+++ b/drivers/cpufreq/cpufreq-dt-platdev.c
-@@ -177,6 +177,7 @@ static const struct of_device_id blockli
- { .compatible = "ti,am625", },
- { .compatible = "ti,am62a7", },
-
-+ { .compatible = "qcom,ipq6018", },
- { .compatible = "qcom,ipq8064", },
- { .compatible = "qcom,apq8064", },
- { .compatible = "qcom,msm8974", },
---- a/drivers/cpufreq/qcom-cpufreq-nvmem.c
-+++ b/drivers/cpufreq/qcom-cpufreq-nvmem.c
-@@ -30,6 +30,8 @@
-
- #include <dt-bindings/arm/qcom,ids.h>
-
-+#define IPQ6000_VERSION BIT(2)
-+
- struct qcom_cpufreq_drv;
-
- struct qcom_cpufreq_match_data {
-@@ -207,6 +209,57 @@ len_error:
- return ret;
- }
-
-+static int qcom_cpufreq_ipq6018_name_version(struct device *cpu_dev,
-+ struct nvmem_cell *speedbin_nvmem,
-+ char **pvs_name,
-+ struct qcom_cpufreq_drv *drv)
-+{
-+ u32 msm_id;
-+ int ret;
-+ u8 *speedbin;
-+ *pvs_name = NULL;
-+
-+ ret = qcom_smem_get_soc_id(&msm_id);
-+ if (ret)
-+ return ret;
-+
-+ speedbin = nvmem_cell_read(speedbin_nvmem, NULL);
-+ if (IS_ERR(speedbin))
-+ return PTR_ERR(speedbin);
-+
-+ switch (msm_id) {
-+ case QCOM_ID_IPQ6005:
-+ case QCOM_ID_IPQ6010:
-+ case QCOM_ID_IPQ6018:
-+ case QCOM_ID_IPQ6028:
-+ /* Fuse Value Freq BIT to set
-+ * ---------------------------------
-+ * 2’b0 No Limit BIT(0)
-+ * 2’b1 1.5 GHz BIT(1)
-+ */
-+ drv->versions = 1 << (unsigned int)(*speedbin);
-+ break;
-+ case QCOM_ID_IPQ6000:
-+ /*
-+ * IPQ6018 family only has one bit to advertise the CPU
-+ * speed-bin, but that is not enough for IPQ6000 which
-+ * is only rated up to 1.2GHz.
-+ * So for IPQ6000 manually set BIT(2) based on SMEM ID.
-+ */
-+ drv->versions = IPQ6000_VERSION;
-+ break;
-+ default:
-+ dev_err(cpu_dev,
-+ "SoC ID %u is not part of IPQ6018 family, limiting to 1.2GHz!\n",
-+ msm_id);
-+ drv->versions = IPQ6000_VERSION;
-+ break;
-+ }
-+
-+ kfree(speedbin);
-+ return 0;
-+}
-+
- static const struct qcom_cpufreq_match_data match_data_kryo = {
- .get_version = qcom_cpufreq_kryo_name_version,
- };
-@@ -221,6 +274,10 @@ static const struct qcom_cpufreq_match_d
- .genpd_names = qcs404_genpd_names,
- };
-
-+static const struct qcom_cpufreq_match_data match_data_ipq6018 = {
-+ .get_version = qcom_cpufreq_ipq6018_name_version,
-+};
-+
- static int qcom_cpufreq_probe(struct platform_device *pdev)
- {
- struct qcom_cpufreq_drv *drv;
-@@ -353,6 +410,7 @@ static const struct of_device_id qcom_cp
- { .compatible = "qcom,apq8096", .data = &match_data_kryo },
- { .compatible = "qcom,msm8996", .data = &match_data_kryo },
- { .compatible = "qcom,qcs404", .data = &match_data_qcs404 },
-+ { .compatible = "qcom,ipq6018", .data = &match_data_ipq6018 },
- { .compatible = "qcom,ipq8064", .data = &match_data_krait },
- { .compatible = "qcom,apq8064", .data = &match_data_krait },
- { .compatible = "qcom,msm8974", .data = &match_data_krait },
diff --git a/target/linux/qualcommax/patches-6.12/0003-v6.7-cpufreq-qcom-nvmem-add-support-for-IPQ8074.patch b/target/linux/qualcommax/patches-6.12/0003-v6.7-cpufreq-qcom-nvmem-add-support-for-IPQ8074.patch
deleted file mode 100644
index 5640038404..0000000000
--- a/target/linux/qualcommax/patches-6.12/0003-v6.7-cpufreq-qcom-nvmem-add-support-for-IPQ8074.patch
+++ /dev/null
@@ -1,113 +0,0 @@
-From 0b9cd949136f1b63f7aa9424b6e583a1ab261e36 Mon Sep 17 00:00:00 2001
-From: Robert Marko <robimarko at gmail.com>
-Date: Fri, 13 Oct 2023 19:20:02 +0200
-Subject: [PATCH] cpufreq: qcom-nvmem: add support for IPQ8074
-
-IPQ8074 comes in 3 families:
-* IPQ8070A/IPQ8071A (Acorn) up to 1.4GHz
-* IPQ8172/IPQ8173/IPQ8174 (Oak) up to 1.4GHz
-* IPQ8072A/IPQ8074A/IPQ8076A/IPQ8078A (Hawkeye) up to 2.2GHz
-
-So, in order to be able to share one OPP table lets add support for IPQ8074
-family based of SMEM SoC ID-s as speedbin fuse is always 0 on IPQ8074.
-
-IPQ8074 compatible is blacklisted from DT platdev as the cpufreq device
-will get created by NVMEM CPUFreq driver.
-
-Signed-off-by: Robert Marko <robimarko at gmail.com>
-Acked-by: Konrad Dybcio <konrad.dybcio at linaro.org>
-[ Viresh: Fixed rebase conflict. ]
-Signed-off-by: Viresh Kumar <viresh.kumar at linaro.org>
----
- drivers/cpufreq/cpufreq-dt-platdev.c | 1 +
- drivers/cpufreq/qcom-cpufreq-nvmem.c | 48 ++++++++++++++++++++++++++++
- 2 files changed, 49 insertions(+)
-
---- a/drivers/cpufreq/cpufreq-dt-platdev.c
-+++ b/drivers/cpufreq/cpufreq-dt-platdev.c
-@@ -179,6 +179,7 @@ static const struct of_device_id blockli
-
- { .compatible = "qcom,ipq6018", },
- { .compatible = "qcom,ipq8064", },
-+ { .compatible = "qcom,ipq8074", },
- { .compatible = "qcom,apq8064", },
- { .compatible = "qcom,msm8974", },
- { .compatible = "qcom,msm8960", },
---- a/drivers/cpufreq/qcom-cpufreq-nvmem.c
-+++ b/drivers/cpufreq/qcom-cpufreq-nvmem.c
-@@ -32,6 +32,11 @@
-
- #define IPQ6000_VERSION BIT(2)
-
-+enum ipq8074_versions {
-+ IPQ8074_HAWKEYE_VERSION = 0,
-+ IPQ8074_ACORN_VERSION,
-+};
-+
- struct qcom_cpufreq_drv;
-
- struct qcom_cpufreq_match_data {
-@@ -260,6 +265,44 @@ static int qcom_cpufreq_ipq6018_name_ver
- return 0;
- }
-
-+static int qcom_cpufreq_ipq8074_name_version(struct device *cpu_dev,
-+ struct nvmem_cell *speedbin_nvmem,
-+ char **pvs_name,
-+ struct qcom_cpufreq_drv *drv)
-+{
-+ u32 msm_id;
-+ int ret;
-+ *pvs_name = NULL;
-+
-+ ret = qcom_smem_get_soc_id(&msm_id);
-+ if (ret)
-+ return ret;
-+
-+ switch (msm_id) {
-+ case QCOM_ID_IPQ8070A:
-+ case QCOM_ID_IPQ8071A:
-+ case QCOM_ID_IPQ8172:
-+ case QCOM_ID_IPQ8173:
-+ case QCOM_ID_IPQ8174:
-+ drv->versions = BIT(IPQ8074_ACORN_VERSION);
-+ break;
-+ case QCOM_ID_IPQ8072A:
-+ case QCOM_ID_IPQ8074A:
-+ case QCOM_ID_IPQ8076A:
-+ case QCOM_ID_IPQ8078A:
-+ drv->versions = BIT(IPQ8074_HAWKEYE_VERSION);
-+ break;
-+ default:
-+ dev_err(cpu_dev,
-+ "SoC ID %u is not part of IPQ8074 family, limiting to 1.4GHz!\n",
-+ msm_id);
-+ drv->versions = BIT(IPQ8074_ACORN_VERSION);
-+ break;
-+ }
-+
-+ return 0;
-+}
-+
- static const struct qcom_cpufreq_match_data match_data_kryo = {
- .get_version = qcom_cpufreq_kryo_name_version,
- };
-@@ -278,6 +321,10 @@ static const struct qcom_cpufreq_match_d
- .get_version = qcom_cpufreq_ipq6018_name_version,
- };
-
-+static const struct qcom_cpufreq_match_data match_data_ipq8074 = {
-+ .get_version = qcom_cpufreq_ipq8074_name_version,
-+};
-+
- static int qcom_cpufreq_probe(struct platform_device *pdev)
- {
- struct qcom_cpufreq_drv *drv;
-@@ -412,6 +459,7 @@ static const struct of_device_id qcom_cp
- { .compatible = "qcom,qcs404", .data = &match_data_qcs404 },
- { .compatible = "qcom,ipq6018", .data = &match_data_ipq6018 },
- { .compatible = "qcom,ipq8064", .data = &match_data_krait },
-+ { .compatible = "qcom,ipq8074", .data = &match_data_ipq8074 },
- { .compatible = "qcom,apq8064", .data = &match_data_krait },
- { .compatible = "qcom,msm8974", .data = &match_data_krait },
- { .compatible = "qcom,msm8960", .data = &match_data_krait },
diff --git a/target/linux/qualcommax/patches-6.12/0004-v6.7-clk-qcom-apss-ipq6018-add-the-GPLL0-clock-also-as-cl.patch b/target/linux/qualcommax/patches-6.12/0004-v6.7-clk-qcom-apss-ipq6018-add-the-GPLL0-clock-also-as-cl.patch
deleted file mode 100644
index ddd53f9d42..0000000000
--- a/target/linux/qualcommax/patches-6.12/0004-v6.7-clk-qcom-apss-ipq6018-add-the-GPLL0-clock-also-as-cl.patch
+++ /dev/null
@@ -1,43 +0,0 @@
-From c917237a7cb17b97cc48e073881a9873f3caeaa2 Mon Sep 17 00:00:00 2001
-From: Kathiravan Thirumoorthy <quic_kathirav at quicinc.com>
-Date: Thu, 14 Sep 2023 12:29:57 +0530
-Subject: [PATCH] clk: qcom: apss-ipq6018: add the GPLL0 clock also as clock
- provider
-
-While the kernel is booting up, APSS PLL will be running at 800MHz with
-GPLL0 as source. Once the cpufreq driver is available, APSS PLL will be
-configured and select the rate based on the opp table and the source will
-be changed to APSS_PLL_EARLY.
-
-Without this patch, CPU Freq driver reports that CPU is running at 24MHz
-instead of the 800MHz.
-
-Reviewed-by: Konrad Dybcio <konrad.dybcio at linaro.org>
-Tested-by: Robert Marko <robimarko at gmail.com>
-Signed-off-by: Kathiravan Thirumoorthy <quic_kathirav at quicinc.com>
----
- drivers/clk/qcom/apss-ipq6018.c | 3 +++
- 1 file changed, 3 insertions(+)
-
---- a/drivers/clk/qcom/apss-ipq6018.c
-+++ b/drivers/clk/qcom/apss-ipq6018.c
-@@ -20,16 +20,19 @@
-
- enum {
- P_XO,
-+ P_GPLL0,
- P_APSS_PLL_EARLY,
- };
-
- static const struct clk_parent_data parents_apcs_alias0_clk_src[] = {
- { .fw_name = "xo" },
-+ { .fw_name = "gpll0" },
- { .fw_name = "pll" },
- };
-
- static const struct parent_map parents_apcs_alias0_clk_src_map[] = {
- { P_XO, 0 },
-+ { P_GPLL0, 4 },
- { P_APSS_PLL_EARLY, 5 },
- };
-
diff --git a/target/linux/qualcommax/patches-6.12/0005-v6.7-arm64-dts-qcom-ipq8074-include-the-GPLL0-as-clock-pr.patch b/target/linux/qualcommax/patches-6.12/0005-v6.7-arm64-dts-qcom-ipq8074-include-the-GPLL0-as-clock-pr.patch
deleted file mode 100644
index 6b7dd2f261..0000000000
--- a/target/linux/qualcommax/patches-6.12/0005-v6.7-arm64-dts-qcom-ipq8074-include-the-GPLL0-as-clock-pr.patch
+++ /dev/null
@@ -1,32 +0,0 @@
-From 3b48a7d925a757b3fa53c04baaf68bb8313c3ffb Mon Sep 17 00:00:00 2001
-From: Kathiravan Thirumoorthy <quic_kathirav at quicinc.com>
-Date: Thu, 14 Sep 2023 12:29:58 +0530
-Subject: [PATCH] arm64: dts: qcom: ipq8074: include the GPLL0 as clock
- provider for mailbox
-
-While the kernel is booting up, APSS PLL will be running at 800MHz with
-GPLL0 as source. Once the cpufreq driver is available, APSS PLL will be
-configured to the rate based on the opp table and the source also will
-be changed to APSS_PLL_EARLY. So allow the mailbox to consume the GPLL0,
-with this inclusion, CPU Freq correctly reports that CPU is running at
-800MHz rather than 24MHz.
-
-Signed-off-by: Kathiravan Thirumoorthy <quic_kathirav at quicinc.com>
-Reviewed-by: Konrad Dybcio <konrad.dybcio at linaro.org>
----
- arch/arm64/boot/dts/qcom/ipq8074.dtsi | 4 ++--
- 1 file changed, 2 insertions(+), 2 deletions(-)
-
---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
-+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
-@@ -723,8 +723,8 @@
- compatible = "qcom,ipq8074-apcs-apps-global",
- "qcom,ipq6018-apcs-apps-global";
- reg = <0x0b111000 0x1000>;
-- clocks = <&a53pll>, <&xo>;
-- clock-names = "pll", "xo";
-+ clocks = <&a53pll>, <&xo>, <&gcc GPLL0>;
-+ clock-names = "pll", "xo", "gpll0";
-
- #clock-cells = <1>;
- #mbox-cells = <1>;
diff --git a/target/linux/qualcommax/patches-6.12/0006-v6.7-arm64-dts-qcom-ipq6018-include-the-GPLL0-as.patch b/target/linux/qualcommax/patches-6.12/0006-v6.7-arm64-dts-qcom-ipq6018-include-the-GPLL0-as.patch
deleted file mode 100644
index d407b9c5c4..0000000000
--- a/target/linux/qualcommax/patches-6.12/0006-v6.7-arm64-dts-qcom-ipq6018-include-the-GPLL0-as.patch
+++ /dev/null
@@ -1,35 +0,0 @@
-From 0133c7af3aa0420778d106cb90db708cfa45f2c6 Mon Sep 17 00:00:00 2001
-From: Kathiravan Thirumoorthy <quic_kathirav at quicinc.com>
-Date: Thu, 14 Sep 2023 12:29:59 +0530
-Subject: [PATCH] arm64: dts: qcom: ipq6018: include the GPLL0 as clock
- provider for mailbox
-
-While the kernel is booting up, APSS clock / CPU clock will be running
-at 800MHz with GPLL0 as source. Once the cpufreq driver is available,
-APSS PLL will be configured to the rate based on the opp table and the
-source also will be changed to APSS_PLL_EARLY. So allow the mailbox to
-consume the GPLL0, with this inclusion, CPU Freq correctly reports that
-CPU is running at 800MHz rather than 24MHz.
-
-Signed-off-by: Kathiravan Thirumoorthy <quic_kathirav at quicinc.com>
-Reviewed-by: Konrad Dybcio <konrad.dybcio at linaro.org>
-Link: https://lore.kernel.org/r/20230913-gpll_cleanup-v2-9-c8ceb1a37680@quicinc.com
-[bjorn: Updated commit message, as requested by Kathiravan]
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- arch/arm64/boot/dts/qcom/ipq6018.dtsi | 4 ++--
- 1 file changed, 2 insertions(+), 2 deletions(-)
-
---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
-+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
-@@ -620,8 +620,8 @@
- compatible = "qcom,ipq6018-apcs-apps-global";
- reg = <0x0 0x0b111000 0x0 0x1000>;
- #clock-cells = <1>;
-- clocks = <&a53pll>, <&xo>;
-- clock-names = "pll", "xo";
-+ clocks = <&a53pll>, <&xo>, <&gcc GPLL0>;
-+ clock-names = "pll", "xo", "gpll0";
- #mbox-cells = <1>;
- };
-
diff --git a/target/linux/qualcommax/patches-6.12/0007-v6.7-clk-qcom-gcc-ipq6018-add-QUP6-I2C-clock.patch b/target/linux/qualcommax/patches-6.12/0007-v6.7-clk-qcom-gcc-ipq6018-add-QUP6-I2C-clock.patch
deleted file mode 100644
index eb68b87640..0000000000
--- a/target/linux/qualcommax/patches-6.12/0007-v6.7-clk-qcom-gcc-ipq6018-add-QUP6-I2C-clock.patch
+++ /dev/null
@@ -1,57 +0,0 @@
-From 3dcf7b59393812a5fbd83f8cd8d34b94afb4c4d1 Mon Sep 17 00:00:00 2001
-From: Robert Marko <robimarko at gmail.com>
-Date: Sat, 21 Oct 2023 13:55:18 +0200
-Subject: [PATCH] clk: qcom: gcc-ipq6018: add QUP6 I2C clock
-
-QUP6 I2C clock is listed in the dt bindings but it was never included in
-the GCC driver.
-So lets add support for it, it is marked as criticial as it is used by RPM
-to communicate to the external PMIC over I2C so this clock must not be
-disabled.
-
-Signed-off-by: Robert Marko <robimarko at gmail.com>
-Reviewed-by: Kathiravan Thirumoorthy <quic_kathirav at quicinc.com>
-Reviewed-by: Konrad Dybcio <konrad.dybcio at linaro.org>
-Link: https://lore.kernel.org/r/20231021115545.229060-1-robimarko@gmail.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- drivers/clk/qcom/gcc-ipq6018.c | 21 +++++++++++++++++++++
- 1 file changed, 21 insertions(+)
-
---- a/drivers/clk/qcom/gcc-ipq6018.c
-+++ b/drivers/clk/qcom/gcc-ipq6018.c
-@@ -2121,6 +2121,26 @@ static struct clk_branch gcc_blsp1_qup5_
- },
- };
-
-+static struct clk_branch gcc_blsp1_qup6_i2c_apps_clk = {
-+ .halt_reg = 0x07010,
-+ .clkr = {
-+ .enable_reg = 0x07010,
-+ .enable_mask = BIT(0),
-+ .hw.init = &(struct clk_init_data){
-+ .name = "gcc_blsp1_qup6_i2c_apps_clk",
-+ .parent_hws = (const struct clk_hw *[]){
-+ &blsp1_qup6_i2c_apps_clk_src.clkr.hw },
-+ .num_parents = 1,
-+ /*
-+ * RPM uses QUP6 I2C to communicate with the external
-+ * PMIC so it must not be disabled.
-+ */
-+ .flags = CLK_SET_RATE_PARENT | CLK_IS_CRITICAL,
-+ .ops = &clk_branch2_ops,
-+ },
-+ },
-+};
-+
- static struct clk_branch gcc_blsp1_qup6_spi_apps_clk = {
- .halt_reg = 0x0700c,
- .clkr = {
-@@ -4277,6 +4297,7 @@ static struct clk_regmap *gcc_ipq6018_cl
- [GCC_BLSP1_QUP4_SPI_APPS_CLK] = &gcc_blsp1_qup4_spi_apps_clk.clkr,
- [GCC_BLSP1_QUP5_I2C_APPS_CLK] = &gcc_blsp1_qup5_i2c_apps_clk.clkr,
- [GCC_BLSP1_QUP5_SPI_APPS_CLK] = &gcc_blsp1_qup5_spi_apps_clk.clkr,
-+ [GCC_BLSP1_QUP6_I2C_APPS_CLK] = &gcc_blsp1_qup6_i2c_apps_clk.clkr,
- [GCC_BLSP1_QUP6_SPI_APPS_CLK] = &gcc_blsp1_qup6_spi_apps_clk.clkr,
- [GCC_BLSP1_UART1_APPS_CLK] = &gcc_blsp1_uart1_apps_clk.clkr,
- [GCC_BLSP1_UART2_APPS_CLK] = &gcc_blsp1_uart2_apps_clk.clkr,
diff --git a/target/linux/qualcommax/patches-6.12/0008-v6.8-arm64-dts-qcom-ipq6018-use-CPUFreq-NVMEM.patch b/target/linux/qualcommax/patches-6.12/0008-v6.8-arm64-dts-qcom-ipq6018-use-CPUFreq-NVMEM.patch
deleted file mode 100644
index 6198e24f38..0000000000
--- a/target/linux/qualcommax/patches-6.12/0008-v6.8-arm64-dts-qcom-ipq6018-use-CPUFreq-NVMEM.patch
+++ /dev/null
@@ -1,85 +0,0 @@
-From 83afcf14edb9217e58837eb119da96d734a4b3b1 Mon Sep 17 00:00:00 2001
-From: Robert Marko <robimarko at gmail.com>
-Date: Sat, 21 Oct 2023 14:00:07 +0200
-Subject: [PATCH] arm64: dts: qcom: ipq6018: use CPUFreq NVMEM
-
-IPQ6018 comes in multiple SKU-s and some of them dont support all of the
-OPP-s that are current set, so lets utilize CPUFreq NVMEM to allow only
-supported OPP-s based on the SoC dynamically.
-
-As an example, IPQ6018 is generaly rated at 1.8GHz but some silicon only
-goes up to 1.5GHz and is marked as such via an eFuse.
-
-Signed-off-by: Robert Marko <robimarko at gmail.com>
-Reviewed-by: Konrad Dybcio <konrad.dybcio at linaro.org>
-Link: https://lore.kernel.org/r/20231021120048.231239-1-robimarko@gmail.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- arch/arm64/boot/dts/qcom/ipq6018.dtsi | 14 +++++++++++++-
- 1 file changed, 13 insertions(+), 1 deletion(-)
-
---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
-+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
-@@ -96,42 +96,49 @@
- };
-
- cpu_opp_table: opp-table-cpu {
-- compatible = "operating-points-v2";
-+ compatible = "operating-points-v2-kryo-cpu";
-+ nvmem-cells = <&cpu_speed_bin>;
- opp-shared;
-
- opp-864000000 {
- opp-hz = /bits/ 64 <864000000>;
- opp-microvolt = <725000>;
-+ opp-supported-hw = <0xf>;
- clock-latency-ns = <200000>;
- };
-
- opp-1056000000 {
- opp-hz = /bits/ 64 <1056000000>;
- opp-microvolt = <787500>;
-+ opp-supported-hw = <0xf>;
- clock-latency-ns = <200000>;
- };
-
- opp-1320000000 {
- opp-hz = /bits/ 64 <1320000000>;
- opp-microvolt = <862500>;
-+ opp-supported-hw = <0x3>;
- clock-latency-ns = <200000>;
- };
-
- opp-1440000000 {
- opp-hz = /bits/ 64 <1440000000>;
- opp-microvolt = <925000>;
-+ opp-supported-hw = <0x3>;
- clock-latency-ns = <200000>;
- };
-
- opp-1608000000 {
- opp-hz = /bits/ 64 <1608000000>;
- opp-microvolt = <987500>;
-+ opp-supported-hw = <0x1>;
- clock-latency-ns = <200000>;
- };
-
- opp-1800000000 {
- opp-hz = /bits/ 64 <1800000000>;
- opp-microvolt = <1062500>;
-+ opp-supported-hw = <0x1>;
- clock-latency-ns = <200000>;
- };
- };
-@@ -322,6 +329,11 @@
- reg = <0x0 0x000a4000 0x0 0x2000>;
- #address-cells = <1>;
- #size-cells = <1>;
-+
-+ cpu_speed_bin: cpu-speed-bin at 135 {
-+ reg = <0x135 0x1>;
-+ bits = <7 1>;
-+ };
- };
-
- prng: qrng at e3000 {
diff --git a/target/linux/qualcommax/patches-6.12/0009-v6.8-arm64-dts-ipq6018-Add-remaining-QUP-UART-node.patch b/target/linux/qualcommax/patches-6.12/0009-v6.8-arm64-dts-ipq6018-Add-remaining-QUP-UART-node.patch
deleted file mode 100644
index af3e132584..0000000000
--- a/target/linux/qualcommax/patches-6.12/0009-v6.8-arm64-dts-ipq6018-Add-remaining-QUP-UART-node.patch
+++ /dev/null
@@ -1,81 +0,0 @@
-From e6c32770ef83f3e8cc057f3920b1c06aa9d1c9c2 Mon Sep 17 00:00:00 2001
-From: Chukun Pan <amadeus at jmu.edu.cn>
-Date: Sun, 3 Dec 2023 23:39:14 +0800
-Subject: [PATCH] arm64: dts: qcom: ipq6018: Add remaining QUP UART node
-
-Add node to support all the QUP UART node controller inside of IPQ6018.
-Some routers use these bus to connect Bluetooth chips.
-
-Signed-off-by: Chukun Pan <amadeus at jmu.edu.cn>
-Link: https://lore.kernel.org/r/20231203153914.532654-1-amadeus@jmu.edu.cn
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- arch/arm64/boot/dts/qcom/ipq6018.dtsi | 50 +++++++++++++++++++++++++++
- 1 file changed, 50 insertions(+)
-
---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
-+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
-@@ -459,6 +459,26 @@
- qcom,ee = <0>;
- };
-
-+ blsp1_uart1: serial at 78af000 {
-+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
-+ reg = <0x0 0x78af000 0x0 0x200>;
-+ interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
-+ clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
-+ <&gcc GCC_BLSP1_AHB_CLK>;
-+ clock-names = "core", "iface";
-+ status = "disabled";
-+ };
-+
-+ blsp1_uart2: serial at 78b0000 {
-+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
-+ reg = <0x0 0x78b0000 0x0 0x200>;
-+ interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
-+ clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
-+ <&gcc GCC_BLSP1_AHB_CLK>;
-+ clock-names = "core", "iface";
-+ status = "disabled";
-+ };
-+
- blsp1_uart3: serial at 78b1000 {
- compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
- reg = <0x0 0x078b1000 0x0 0x200>;
-@@ -467,6 +487,36 @@
- <&gcc GCC_BLSP1_AHB_CLK>;
- clock-names = "core", "iface";
- status = "disabled";
-+ };
-+
-+ blsp1_uart4: serial at 78b2000 {
-+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
-+ reg = <0x0 0x078b2000 0x0 0x200>;
-+ interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
-+ clocks = <&gcc GCC_BLSP1_UART4_APPS_CLK>,
-+ <&gcc GCC_BLSP1_AHB_CLK>;
-+ clock-names = "core", "iface";
-+ status = "disabled";
-+ };
-+
-+ blsp1_uart5: serial at 78b3000 {
-+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
-+ reg = <0x0 0x78b3000 0x0 0x200>;
-+ interrupts = <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>;
-+ clocks = <&gcc GCC_BLSP1_UART5_APPS_CLK>,
-+ <&gcc GCC_BLSP1_AHB_CLK>;
-+ clock-names = "core", "iface";
-+ status = "disabled";
-+ };
-+
-+ blsp1_uart6: serial at 78b4000 {
-+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
-+ reg = <0x0 0x078b4000 0x0 0x200>;
-+ interrupts = <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>;
-+ clocks = <&gcc GCC_BLSP1_UART6_APPS_CLK>,
-+ <&gcc GCC_BLSP1_AHB_CLK>;
-+ clock-names = "core", "iface";
-+ status = "disabled";
- };
-
- blsp1_spi1: spi at 78b5000 {
diff --git a/target/linux/qualcommax/patches-6.12/0010-v6.9-arm64-dts-qcom-Fix-hs_phy_irq-for-QUSB2-targets.patch b/target/linux/qualcommax/patches-6.12/0010-v6.9-arm64-dts-qcom-Fix-hs_phy_irq-for-QUSB2-targets.patch
deleted file mode 100644
index 6559f3bbe9..0000000000
--- a/target/linux/qualcommax/patches-6.12/0010-v6.9-arm64-dts-qcom-Fix-hs_phy_irq-for-QUSB2-targets.patch
+++ /dev/null
@@ -1,95 +0,0 @@
-From 2c6597c72e9722ac020102d5af40126df0437b82 Mon Sep 17 00:00:00 2001
-From: Krishna Kurapati <quic_kriskura at quicinc.com>
-Date: Fri, 26 Jan 2024 00:29:18 +0530
-Subject: [PATCH] arm64: dts: qcom: Fix hs_phy_irq for QUSB2 targets
-
-On several QUSB2 Targets, the hs_phy_irq mentioned is actually
-qusb2_phy interrupt specific to QUSB2 PHY's. Rename hs_phy_irq
-to qusb2_phy for such targets.
-
-In actuality, the hs_phy_irq is also present in these targets, but
-kept in for debug purposes in hw test environments. This is not
-triggered by default and its functionality is mutually exclusive
-to that of qusb2_phy interrupt.
-
-Add missing hs_phy_irq's, pwr_event irq's for QUSB2 PHY targets.
-Add missing ss_phy_irq on some targets which allows for remote
-wakeup to work on a Super Speed link.
-
-Also modify order of interrupts in accordance to bindings update.
-Since driver looks up for interrupts by name and not by index, it
-is safe to modify order of these interrupts in the DT.
-
-Signed-off-by: Krishna Kurapati <quic_kriskura at quicinc.com>
-Link: https://lore.kernel.org/r/20240125185921.5062-2-quic_kriskura@quicinc.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- arch/arm64/boot/dts/qcom/ipq6018.dtsi | 13 +++++++++++++
- arch/arm64/boot/dts/qcom/ipq8074.dtsi | 14 ++++++++++++++
- arch/arm64/boot/dts/qcom/msm8953.dtsi | 7 +++++--
- arch/arm64/boot/dts/qcom/msm8996.dtsi | 8 ++++++--
- arch/arm64/boot/dts/qcom/msm8998.dtsi | 7 +++++--
- arch/arm64/boot/dts/qcom/sdm630.dtsi | 17 +++++++++++++----
- arch/arm64/boot/dts/qcom/sm6115.dtsi | 9 +++++++--
- arch/arm64/boot/dts/qcom/sm6125.dtsi | 9 +++++++--
- 8 files changed, 70 insertions(+), 14 deletions(-)
-
---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
-+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
-@@ -431,6 +431,12 @@
- <&gcc GCC_USB1_MOCK_UTMI_CLK>;
- assigned-clock-rates = <133330000>,
- <24000000>;
-+
-+ interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>,
-+ <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
-+ interrupt-names = "pwr_event",
-+ "qusb2_phy";
-+
- resets = <&gcc GCC_USB1_BCR>;
- status = "disabled";
-
-@@ -629,6 +635,13 @@
- <133330000>,
- <24000000>;
-
-+ interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
-+ <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
-+ <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
-+ interrupt-names = "pwr_event",
-+ "qusb2_phy",
-+ "ss_phy_irq";
-+
- resets = <&gcc GCC_USB0_BCR>;
- status = "disabled";
-
---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
-+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
-@@ -632,6 +632,13 @@
- <133330000>,
- <19200000>;
-
-+ interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
-+ <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
-+ <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
-+ interrupt-names = "pwr_event",
-+ "qusb2_phy",
-+ "ss_phy_irq";
-+
- power-domains = <&gcc USB0_GDSC>;
-
- resets = <&gcc GCC_USB0_BCR>;
-@@ -675,6 +682,13 @@
- <133330000>,
- <19200000>;
-
-+ interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>,
-+ <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
-+ <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
-+ interrupt-names = "pwr_event",
-+ "qusb2_phy",
-+ "ss_phy_irq";
-+
- power-domains = <&gcc USB1_GDSC>;
-
- resets = <&gcc GCC_USB1_BCR>;
diff --git a/target/linux/qualcommax/patches-6.12/0011-v6.8-hwspinlock-qcom-Remove-IPQ6018-SOC-specific-.patch b/target/linux/qualcommax/patches-6.12/0011-v6.8-hwspinlock-qcom-Remove-IPQ6018-SOC-specific-.patch
deleted file mode 100644
index 25d56870a4..0000000000
--- a/target/linux/qualcommax/patches-6.12/0011-v6.8-hwspinlock-qcom-Remove-IPQ6018-SOC-specific-.patch
+++ /dev/null
@@ -1,32 +0,0 @@
-From c3dc3d079d191c9149496b3c7fe1ece909386d93 Mon Sep 17 00:00:00 2001
-From: Vignesh Viswanathan <quic_viswanat at quicinc.com>
-Date: Tue, 5 Sep 2023 15:25:35 +0530
-Subject: [PATCH] hwspinlock: qcom: Remove IPQ6018 SOC specific compatible
-
-IPQ6018 has 32 tcsr_mutex hwlock registers with stride 0x1000.
-The compatible string qcom,ipq6018-tcsr-mutex is mapped to
-of_msm8226_tcsr_mutex which has 32 locks configured with stride of 0x80
-and doesn't match the HW present in IPQ6018.
-
-Remove IPQ6018 specific compatible string so that it fallsback to
-of_tcsr_mutex data which maps to the correct configuration for IPQ6018.
-
-Fixes: 5d4753f741d8 ("hwspinlock: qcom: add support for MMIO on older SoCs")
-Signed-off-by: Vignesh Viswanathan <quic_viswanat at quicinc.com>
-Reviewed-by: Konrad Dybcio <konrad.dybcio at linaro.org>
-Link: https://lore.kernel.org/r/20230905095535.1263113-3-quic_viswanat@quicinc.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- drivers/hwspinlock/qcom_hwspinlock.c | 1 -
- 1 file changed, 1 deletion(-)
-
---- a/drivers/hwspinlock/qcom_hwspinlock.c
-+++ b/drivers/hwspinlock/qcom_hwspinlock.c
-@@ -115,7 +115,6 @@ static const struct of_device_id qcom_hw
- { .compatible = "qcom,sfpb-mutex", .data = &of_sfpb_mutex },
- { .compatible = "qcom,tcsr-mutex", .data = &of_tcsr_mutex },
- { .compatible = "qcom,apq8084-tcsr-mutex", .data = &of_msm8226_tcsr_mutex },
-- { .compatible = "qcom,ipq6018-tcsr-mutex", .data = &of_msm8226_tcsr_mutex },
- { .compatible = "qcom,msm8226-tcsr-mutex", .data = &of_msm8226_tcsr_mutex },
- { .compatible = "qcom,msm8974-tcsr-mutex", .data = &of_msm8226_tcsr_mutex },
- { .compatible = "qcom,msm8994-tcsr-mutex", .data = &of_msm8226_tcsr_mutex },
diff --git a/target/linux/qualcommax/patches-6.12/0012-v6.9-arm64-dts-qcom-ipq6018-add-tsens-node.patch b/target/linux/qualcommax/patches-6.12/0012-v6.9-arm64-dts-qcom-ipq6018-add-tsens-node.patch
deleted file mode 100644
index 29d2de9b23..0000000000
--- a/target/linux/qualcommax/patches-6.12/0012-v6.9-arm64-dts-qcom-ipq6018-add-tsens-node.patch
+++ /dev/null
@@ -1,34 +0,0 @@
-From 0b17197055b528da22e9385200e61b847b499d48 Mon Sep 17 00:00:00 2001
-From: Mantas Pucka <mantas at 8devices.com>
-Date: Thu, 25 Jan 2024 11:04:11 +0200
-Subject: [PATCH] arm64: dts: qcom: ipq6018: add tsens node
-
-IPQ6018 has temperature sensing HW block compatible with IPQ8074. Add
-node for it.
-
-Signed-off-by: Mantas Pucka <mantas at 8devices.com>
-Link: https://lore.kernel.org/r/1706173452-1017-3-git-send-email-mantas@8devices.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- arch/arm64/boot/dts/qcom/ipq6018.dtsi | 10 ++++++++++
- 1 file changed, 10 insertions(+)
-
---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
-+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
-@@ -343,6 +343,16 @@
- clock-names = "core";
- };
-
-+ tsens: thermal-sensor at 4a9000 {
-+ compatible = "qcom,ipq6018-tsens", "qcom,ipq8074-tsens";
-+ reg = <0x0 0x004a9000 0x0 0x1000>,
-+ <0x0 0x004a8000 0x0 0x1000>;
-+ interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
-+ interrupt-names = "combined";
-+ #qcom,sensors = <16>;
-+ #thermal-sensor-cells = <1>;
-+ };
-+
- cryptobam: dma-controller at 704000 {
- compatible = "qcom,bam-v1.7.0";
- reg = <0x0 0x00704000 0x0 0x20000>;
diff --git a/target/linux/qualcommax/patches-6.12/0013-v6.9-arm64-dts-qcom-ipq6018-add-thermal-zones.patch b/target/linux/qualcommax/patches-6.12/0013-v6.9-arm64-dts-qcom-ipq6018-add-thermal-zones.patch
deleted file mode 100644
index 7e8c84558e..0000000000
--- a/target/linux/qualcommax/patches-6.12/0013-v6.9-arm64-dts-qcom-ipq6018-add-thermal-zones.patch
+++ /dev/null
@@ -1,180 +0,0 @@
-From 8f053e5616352943e16966f195f5a7a161e6fe7d Mon Sep 17 00:00:00 2001
-From: Mantas Pucka <mantas at 8devices.com>
-Date: Thu, 25 Jan 2024 11:04:12 +0200
-Subject: [PATCH] arm64: dts: qcom: ipq6018: add thermal zones
-
-Add thermal zones to make use of thermal sensors data. For CPU zone,
-add cooling device that uses CPU frequency scaling.
-
-Signed-off-by: Mantas Pucka <mantas at 8devices.com>
-Link: https://lore.kernel.org/r/1706173452-1017-4-git-send-email-mantas@8devices.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- arch/arm64/boot/dts/qcom/ipq6018.dtsi | 121 ++++++++++++++++++++++++++
- 1 file changed, 121 insertions(+)
-
---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
-+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
-@@ -9,6 +9,7 @@
- #include <dt-bindings/clock/qcom,gcc-ipq6018.h>
- #include <dt-bindings/reset/qcom,gcc-ipq6018.h>
- #include <dt-bindings/clock/qcom,apss-ipq.h>
-+#include <dt-bindings/thermal/thermal.h>
-
- / {
- #address-cells = <2>;
-@@ -43,6 +44,7 @@
- clock-names = "cpu";
- operating-points-v2 = <&cpu_opp_table>;
- cpu-supply = <&ipq6018_s2>;
-+ #cooling-cells = <2>;
- };
-
- CPU1: cpu at 1 {
-@@ -55,6 +57,7 @@
- clock-names = "cpu";
- operating-points-v2 = <&cpu_opp_table>;
- cpu-supply = <&ipq6018_s2>;
-+ #cooling-cells = <2>;
- };
-
- CPU2: cpu at 2 {
-@@ -67,6 +70,7 @@
- clock-names = "cpu";
- operating-points-v2 = <&cpu_opp_table>;
- cpu-supply = <&ipq6018_s2>;
-+ #cooling-cells = <2>;
- };
-
- CPU3: cpu at 3 {
-@@ -79,6 +83,7 @@
- clock-names = "cpu";
- operating-points-v2 = <&cpu_opp_table>;
- cpu-supply = <&ipq6018_s2>;
-+ #cooling-cells = <2>;
- };
-
- L2_0: l2-cache {
-@@ -890,6 +895,122 @@
- };
- };
-
-+ thermal-zones {
-+ nss-top-thermal {
-+ polling-delay-passive = <250>;
-+ polling-delay = <1000>;
-+ thermal-sensors = <&tsens 4>;
-+
-+ trips {
-+ nss-top-critical {
-+ temperature = <125000>;
-+ hysteresis = <1000>;
-+ type = "critical";
-+ };
-+ };
-+ };
-+
-+ nss-thermal {
-+ polling-delay-passive = <250>;
-+ polling-delay = <1000>;
-+ thermal-sensors = <&tsens 5>;
-+
-+ trips {
-+ nss-critical {
-+ temperature = <125000>;
-+ hysteresis = <1000>;
-+ type = "critical";
-+ };
-+ };
-+ };
-+
-+ wcss-phya0-thermal {
-+ polling-delay-passive = <250>;
-+ polling-delay = <1000>;
-+ thermal-sensors = <&tsens 7>;
-+
-+ trips {
-+ wcss-phya0-critical {
-+ temperature = <125000>;
-+ hysteresis = <1000>;
-+ type = "critical";
-+ };
-+ };
-+ };
-+
-+ wcss-phya1-thermal {
-+ polling-delay-passive = <250>;
-+ polling-delay = <1000>;
-+ thermal-sensors = <&tsens 8>;
-+
-+ trips {
-+ wcss-phya1-critical {
-+ temperature = <125000>;
-+ hysteresis = <1000>;
-+ type = "critical";
-+ };
-+ };
-+ };
-+
-+ cpu-thermal {
-+ polling-delay-passive = <250>;
-+ polling-delay = <1000>;
-+ thermal-sensors = <&tsens 13>;
-+
-+ trips {
-+ cpu-critical {
-+ temperature = <125000>;
-+ hysteresis = <1000>;
-+ type = "critical";
-+ };
-+
-+ cpu_alert: cpu-passive {
-+ temperature = <110000>;
-+ hysteresis = <1000>;
-+ type = "passive";
-+ };
-+ };
-+
-+ cooling-maps {
-+ map0 {
-+ trip = <&cpu_alert>;
-+ cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-+ <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-+ <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-+ <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-+ };
-+ };
-+ };
-+
-+ lpass-thermal {
-+ polling-delay-passive = <250>;
-+ polling-delay = <1000>;
-+ thermal-sensors = <&tsens 14>;
-+
-+ trips {
-+ lpass-critical {
-+ temperature = <125000>;
-+ hysteresis = <1000>;
-+ type = "critical";
-+ };
-+ };
-+ };
-+
-+ ddrss-top-thermal {
-+ polling-delay-passive = <250>;
-+ polling-delay = <1000>;
-+ thermal-sensors = <&tsens 15>;
-+
-+ trips {
-+ ddrss-top-critical {
-+ temperature = <125000>;
-+ hysteresis = <1000>;
-+ type = "critical";
-+ };
-+ };
-+ };
-+ };
-+
- timer {
- compatible = "arm,armv8-timer";
- interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
diff --git a/target/linux/qualcommax/patches-6.12/0014-v6.9-clk-qcom-gcc-ipq6018-add-qdss_at-clock-needed-for-wi.patch b/target/linux/qualcommax/patches-6.12/0014-v6.9-clk-qcom-gcc-ipq6018-add-qdss_at-clock-needed-for-wi.patch
deleted file mode 100644
index 5f0af1352a..0000000000
--- a/target/linux/qualcommax/patches-6.12/0014-v6.9-clk-qcom-gcc-ipq6018-add-qdss_at-clock-needed-for-wi.patch
+++ /dev/null
@@ -1,50 +0,0 @@
-From fd712118aa1aa758da1fd1546b3f8a1b00e42cbc Mon Sep 17 00:00:00 2001
-From: Mantas Pucka <mantas at 8devices.com>
-Date: Tue, 23 Jan 2024 11:26:09 +0200
-Subject: [PATCH] clk: qcom: gcc-ipq6018: add qdss_at clock needed for wifi
- operation
-
-Without it system hangs upon wifi firmware load. It should be enabled by
-remoteproc/wifi driver. Bindings already exist for it, so add it based
-on vendor code.
-
-Signed-off-by: Mantas Pucka <mantas at 8devices.com>
-Link: https://lore.kernel.org/r/1706001970-26032-1-git-send-email-mantas@8devices.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- drivers/clk/qcom/gcc-ipq6018.c | 17 +++++++++++++++++
- 1 file changed, 17 insertions(+)
-
---- a/drivers/clk/qcom/gcc-ipq6018.c
-+++ b/drivers/clk/qcom/gcc-ipq6018.c
-@@ -3524,6 +3524,22 @@ static struct clk_branch gcc_prng_ahb_cl
- },
- };
-
-+static struct clk_branch gcc_qdss_at_clk = {
-+ .halt_reg = 0x29024,
-+ .clkr = {
-+ .enable_reg = 0x29024,
-+ .enable_mask = BIT(0),
-+ .hw.init = &(struct clk_init_data){
-+ .name = "gcc_qdss_at_clk",
-+ .parent_hws = (const struct clk_hw *[]){
-+ &qdss_at_clk_src.clkr.hw },
-+ .num_parents = 1,
-+ .flags = CLK_SET_RATE_PARENT,
-+ .ops = &clk_branch2_ops,
-+ },
-+ },
-+};
-+
- static struct clk_branch gcc_qdss_dap_clk = {
- .halt_reg = 0x29084,
- .clkr = {
-@@ -4363,6 +4379,7 @@ static struct clk_regmap *gcc_ipq6018_cl
- [GCC_SYS_NOC_PCIE0_AXI_CLK] = &gcc_sys_noc_pcie0_axi_clk.clkr,
- [GCC_PCIE0_PIPE_CLK] = &gcc_pcie0_pipe_clk.clkr,
- [GCC_PRNG_AHB_CLK] = &gcc_prng_ahb_clk.clkr,
-+ [GCC_QDSS_AT_CLK] = &gcc_qdss_at_clk.clkr,
- [GCC_QDSS_DAP_CLK] = &gcc_qdss_dap_clk.clkr,
- [GCC_QPIC_AHB_CLK] = &gcc_qpic_ahb_clk.clkr,
- [GCC_QPIC_CLK] = &gcc_qpic_clk.clkr,
diff --git a/target/linux/qualcommax/patches-6.12/0015-v6.8-phy-qcom-qmp-usb-fix-serdes-init-sequence-for-IPQ6018.patch b/target/linux/qualcommax/patches-6.12/0015-v6.8-phy-qcom-qmp-usb-fix-serdes-init-sequence-for-IPQ6018.patch
deleted file mode 100644
index 9021b572e8..0000000000
--- a/target/linux/qualcommax/patches-6.12/0015-v6.8-phy-qcom-qmp-usb-fix-serdes-init-sequence-for-IPQ6018.patch
+++ /dev/null
@@ -1,58 +0,0 @@
-From 62a5df451ab911421da96655fcc4d1e269ff6e2f Mon Sep 17 00:00:00 2001
-From: Mantas Pucka <mantas at 8devices.com>
-Date: Tue, 23 Jan 2024 18:09:20 +0200
-Subject: [PATCH] phy: qcom-qmp-usb: fix serdes init sequence for IPQ6018
-
-Commit 23fd679249df ("phy: qcom-qmp: add USB3 PHY support for IPQ6018")
-noted that IPQ6018 init is identical to IPQ8074. Yet downstream uses
-separate serdes init sequence for IPQ6018. Since already existing IPQ9574
-serdes init sequence is identical, just reuse it and fix failing USB3 mode
-in IPQ6018.
-
-Fixes: 23fd679249df ("phy: qcom-qmp: add USB3 PHY support for IPQ6018")
-Signed-off-by: Mantas Pucka <mantas at 8devices.com>
-Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
-Link: https://lore.kernel.org/r/1706026160-17520-3-git-send-email-mantas@8devices.com
-Signed-off-by: Vinod Koul <vkoul at kernel.org>
----
- drivers/phy/qualcomm/phy-qcom-qmp-usb.c | 20 +++++++++++++++++++-
- 1 file changed, 19 insertions(+), 1 deletion(-)
-
---- a/drivers/phy/qualcomm/phy-qcom-qmp-usb.c
-+++ b/drivers/phy/qualcomm/phy-qcom-qmp-usb.c
-@@ -1314,6 +1314,26 @@ static const struct qmp_usb_offsets qmp_
- .rx = 0x1000,
- };
-
-+static const struct qmp_phy_cfg ipq6018_usb3phy_cfg = {
-+ .lanes = 1,
-+
-+ .serdes_tbl = ipq9574_usb3_serdes_tbl,
-+ .serdes_tbl_num = ARRAY_SIZE(ipq9574_usb3_serdes_tbl),
-+ .tx_tbl = msm8996_usb3_tx_tbl,
-+ .tx_tbl_num = ARRAY_SIZE(msm8996_usb3_tx_tbl),
-+ .rx_tbl = ipq8074_usb3_rx_tbl,
-+ .rx_tbl_num = ARRAY_SIZE(ipq8074_usb3_rx_tbl),
-+ .pcs_tbl = ipq8074_usb3_pcs_tbl,
-+ .pcs_tbl_num = ARRAY_SIZE(ipq8074_usb3_pcs_tbl),
-+ .clk_list = msm8996_phy_clk_l,
-+ .num_clks = ARRAY_SIZE(msm8996_phy_clk_l),
-+ .reset_list = msm8996_usb3phy_reset_l,
-+ .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l),
-+ .vreg_list = qmp_phy_vreg_l,
-+ .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l),
-+ .regs = qmp_v3_usb3phy_regs_layout,
-+};
-+
- static const struct qmp_phy_cfg ipq8074_usb3phy_cfg = {
- .lanes = 1,
-
-@@ -2239,7 +2259,7 @@ err_node_put:
- static const struct of_device_id qmp_usb_of_match_table[] = {
- {
- .compatible = "qcom,ipq6018-qmp-usb3-phy",
-- .data = &ipq8074_usb3phy_cfg,
-+ .data = &ipq6018_usb3phy_cfg,
- }, {
- .compatible = "qcom,ipq8074-qmp-usb3-phy",
- .data = &ipq8074_usb3phy_cfg,
diff --git a/target/linux/qualcommax/patches-6.12/0016-v6.8-arm64-dts-qcom-ipq8074-Add-QUP4-SPI-node.patch b/target/linux/qualcommax/patches-6.12/0016-v6.8-arm64-dts-qcom-ipq8074-Add-QUP4-SPI-node.patch
deleted file mode 100644
index 16d2437490..0000000000
--- a/target/linux/qualcommax/patches-6.12/0016-v6.8-arm64-dts-qcom-ipq8074-Add-QUP4-SPI-node.patch
+++ /dev/null
@@ -1,38 +0,0 @@
-From 6a25e70214fde6dcf900271c819c8d7fe7b9a4b0 Mon Sep 17 00:00:00 2001
-From: Robert Marko <robimarko at gmail.com>
-Date: Thu, 23 Nov 2023 13:12:54 +0100
-Subject: [PATCH] arm64: dts: qcom: ipq8074: Add QUP4 SPI node
-
-Add node to support the QUP4 SPI controller inside of IPQ8074.
-Some devices use this bus to communicate to a Bluetooth controller.
-
-Signed-off-by: Robert Marko <robimarko at gmail.com>
-Link: https://lore.kernel.org/r/20231123121324.1046164-1-robimarko@gmail.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- arch/arm64/boot/dts/qcom/ipq8074.dtsi | 14 ++++++++++++++
- 1 file changed, 14 insertions(+)
-
---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
-+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
-@@ -536,6 +536,20 @@
- status = "disabled";
- };
-
-+ blsp1_spi4: spi at 78b8000 {
-+ compatible = "qcom,spi-qup-v2.2.1";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <0x78b8000 0x600>;
-+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-+ clocks = <&gcc GCC_BLSP1_QUP4_SPI_APPS_CLK>,
-+ <&gcc GCC_BLSP1_AHB_CLK>;
-+ clock-names = "core", "iface";
-+ dmas = <&blsp_dma 18>, <&blsp_dma 19>;
-+ dma-names = "tx", "rx";
-+ status = "disabled";
-+ };
-+
- blsp1_i2c5: i2c at 78b9000 {
- compatible = "qcom,i2c-qup-v2.2.1";
- #address-cells = <1>;
diff --git a/target/linux/qualcommax/patches-6.12/0017-v6.9-arm64-dts-qcom-ipq8074-Remove-unused-gpio-from-QPIC-.patch b/target/linux/qualcommax/patches-6.12/0017-v6.9-arm64-dts-qcom-ipq8074-Remove-unused-gpio-from-QPIC-.patch
deleted file mode 100644
index e075c590fb..0000000000
--- a/target/linux/qualcommax/patches-6.12/0017-v6.9-arm64-dts-qcom-ipq8074-Remove-unused-gpio-from-QPIC-.patch
+++ /dev/null
@@ -1,32 +0,0 @@
-From 5f78d9213ae753e2242b0f6a5d4a5e98e55ddc76 Mon Sep 17 00:00:00 2001
-From: Paweł Owoc <frut3k7 at gmail.com>
-Date: Wed, 13 Mar 2024 11:27:06 +0100
-Subject: [PATCH] arm64: dts: qcom: ipq8074: Remove unused gpio from QPIC pins
-
-gpio16 will only be used for LCD support, as its NAND/LCDC data[8]
-so its bit 9 of the parallel QPIC interface, and ONFI NAND is only 8
-or 16-bit with only 8-bit one being supported in our case so that pin
-is unused.
-
-It should be dropped from the default NAND pinctrl configuration
-as its unused and only needed for LCD.
-
-Signed-off-by: Paweł Owoc <frut3k7 at gmail.com>
-Reviewed-by: Kathiravan Thirumoorthy <quic_kathirav at quicinc.com>
-Link: https://lore.kernel.org/r/20240313102713.1727458-1-frut3k7@gmail.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- arch/arm64/boot/dts/qcom/ipq8074.dtsi | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
-+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
-@@ -372,7 +372,7 @@
- "gpio5", "gpio6", "gpio7",
- "gpio8", "gpio10", "gpio11",
- "gpio12", "gpio13", "gpio14",
-- "gpio15", "gpio16", "gpio17";
-+ "gpio15", "gpio17";
- function = "qpic";
- drive-strength = <8>;
- bias-disable;
diff --git a/target/linux/qualcommax/patches-6.12/0018-v6.7-arm64-dts-qcom-ipq5018-add-watchdog.patch b/target/linux/qualcommax/patches-6.12/0018-v6.7-arm64-dts-qcom-ipq5018-add-watchdog.patch
deleted file mode 100644
index 8e973e63f2..0000000000
--- a/target/linux/qualcommax/patches-6.12/0018-v6.7-arm64-dts-qcom-ipq5018-add-watchdog.patch
+++ /dev/null
@@ -1,31 +0,0 @@
-From 9cbaee8379e620f82112002f973adde19679df31 Mon Sep 17 00:00:00 2001
-From: Robert Marko <robimarko at gmail.com>
-Date: Wed, 16 Aug 2023 18:14:00 +0200
-Subject: [PATCH] arm64: dts: qcom: ipq5018: add watchdog
-
-Add the required DT node for watchdog operation.
-
-Signed-off-by: Robert Marko <robimarko at gmail.com>
-Reviewed-by: Konrad Dybcio <konrad.dybcio at linaro.org>
-Link: https://lore.kernel.org/r/20230816161455.3310629-2-robimarko@gmail.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- arch/arm64/boot/dts/qcom/ipq5018.dtsi | 7 +++++++
- 1 file changed, 7 insertions(+)
-
---- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
-+++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
-@@ -181,6 +181,13 @@
- };
- };
-
-+ watchdog: watchdog at b017000 {
-+ compatible = "qcom,apss-wdt-ipq5018", "qcom,kpss-wdt";
-+ reg = <0x0b017000 0x40>;
-+ interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>;
-+ clocks = <&sleep_clk>;
-+ };
-+
- timer at b120000 {
- compatible = "arm,armv7-timer-mem";
- reg = <0x0b120000 0x1000>;
diff --git a/target/linux/qualcommax/patches-6.12/0019-v6.7-dt-bindings-firmware-qcom-scm-support-indicating-SDI-default-state.patch b/target/linux/qualcommax/patches-6.12/0019-v6.7-dt-bindings-firmware-qcom-scm-support-indicating-SDI-default-state.patch
deleted file mode 100644
index 46d3c61398..0000000000
--- a/target/linux/qualcommax/patches-6.12/0019-v6.7-dt-bindings-firmware-qcom-scm-support-indicating-SDI-default-state.patch
+++ /dev/null
@@ -1,41 +0,0 @@
-From 92dab9ea5f389c12828283146c60054642453a91 Mon Sep 17 00:00:00 2001
-From: Robert Marko <robimarko at gmail.com>
-Date: Wed, 16 Aug 2023 18:45:38 +0200
-Subject: [PATCH] dt-bindings: firmware: qcom,scm: support indicating SDI
- default state
-
-IPQ5018 has SDI (Secure Debug Image) enabled by TZ by default, and that
-means that WDT being asserted or just trying to reboot will hang the board
-in the debug mode and only pulling the power and repowering will help.
-Some IPQ4019 boards like Google WiFI have it enabled as well.
-
-So, lets add a boolean property to indicate that SDI is enabled by default
-and thus needs to be disabled by the kernel.
-
-Signed-off-by: Robert Marko <robimarko at gmail.com>
-Acked-by: Mukesh Ojha <quic_mojha at quicinc.com>
-Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski at linaro.org>
-Reviewed-by: Brian Norris <computersforpeace at gmail.com>
-Link: https://lore.kernel.org/r/20230816164641.3371878-1-robimarko@gmail.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- Documentation/devicetree/bindings/firmware/qcom,scm.yaml | 8 ++++++++
- 1 file changed, 8 insertions(+)
-
---- a/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
-+++ b/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
-@@ -89,6 +89,14 @@ properties:
- protocol to handle sleeping SCM calls.
- maxItems: 1
-
-+ qcom,sdi-enabled:
-+ description:
-+ Indicates that the SDI (Secure Debug Image) has been enabled by TZ
-+ by default and it needs to be disabled.
-+ If not disabled WDT assertion or reboot will cause the board to hang
-+ in the debug mode.
-+ type: boolean
-+
- qcom,dload-mode:
- $ref: /schemas/types.yaml#/definitions/phandle-array
- items:
diff --git a/target/linux/qualcommax/patches-6.12/0020-v6.7-firmware-qcom-scm-disable-SDI-if-required.patch b/target/linux/qualcommax/patches-6.12/0020-v6.7-firmware-qcom-scm-disable-SDI-if-required.patch
deleted file mode 100644
index 747ba7f285..0000000000
--- a/target/linux/qualcommax/patches-6.12/0020-v6.7-firmware-qcom-scm-disable-SDI-if-required.patch
+++ /dev/null
@@ -1,83 +0,0 @@
-From ff4aa3bc98258a240b9bbab53fd8d2fb8184c485 Mon Sep 17 00:00:00 2001
-From: Robert Marko <robimarko at gmail.com>
-Date: Wed, 16 Aug 2023 18:45:39 +0200
-Subject: [PATCH] firmware: qcom_scm: disable SDI if required
-
-IPQ5018 has SDI (Secure Debug Image) enabled by TZ by default, and that
-means that WDT being asserted or just trying to reboot will hang the board
-in the debug mode and only pulling the power and repowering will help.
-Some IPQ4019 boards like Google WiFI have it enabled as well.
-
-Luckily, SDI can be disabled via an SCM call.
-
-So, lets use the boolean DT property to identify boards that have SDI
-enabled by default and use the SCM call to disable SDI during SCM probe.
-It is important to disable it as soon as possible as we might have a WDT
-assertion at any time which would then leave the board in debug mode,
-thus disabling it during SCM removal is not enough.
-
-Signed-off-by: Robert Marko <robimarko at gmail.com>
-Reviewed-by: Guru Das Srinagesh <quic_gurus at quicinc.com>
-Link: https://lore.kernel.org/r/20230816164641.3371878-2-robimarko@gmail.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- drivers/firmware/qcom_scm.c | 30 ++++++++++++++++++++++++++++++
- drivers/firmware/qcom_scm.h | 1 +
- 2 files changed, 31 insertions(+)
-
---- a/drivers/firmware/qcom_scm.c
-+++ b/drivers/firmware/qcom_scm.c
-@@ -410,6 +410,29 @@ int qcom_scm_set_remote_state(u32 state,
- }
- EXPORT_SYMBOL_GPL(qcom_scm_set_remote_state);
-
-+static int qcom_scm_disable_sdi(void)
-+{
-+ int ret;
-+ struct qcom_scm_desc desc = {
-+ .svc = QCOM_SCM_SVC_BOOT,
-+ .cmd = QCOM_SCM_BOOT_SDI_CONFIG,
-+ .args[0] = 1, /* Disable watchdog debug */
-+ .args[1] = 0, /* Disable SDI */
-+ .arginfo = QCOM_SCM_ARGS(2),
-+ .owner = ARM_SMCCC_OWNER_SIP,
-+ };
-+ struct qcom_scm_res res;
-+
-+ ret = qcom_scm_clk_enable();
-+ if (ret)
-+ return ret;
-+ ret = qcom_scm_call(__scm->dev, &desc, &res);
-+
-+ qcom_scm_clk_disable();
-+
-+ return ret ? : res.result[0];
-+}
-+
- static int __qcom_scm_set_dload_mode(struct device *dev, bool enable)
- {
- struct qcom_scm_desc desc = {
-@@ -1474,6 +1497,13 @@ static int qcom_scm_probe(struct platfor
-
- __get_convention();
-
-+
-+ /*
-+ * Disable SDI if indicated by DT that it is enabled by default.
-+ */
-+ if (of_property_read_bool(pdev->dev.of_node, "qcom,sdi-enabled"))
-+ qcom_scm_disable_sdi();
-+
- /*
- * If requested enable "download mode", from this point on warmboot
- * will cause the boot stages to enter download mode, unless
---- a/drivers/firmware/qcom_scm.h
-+++ b/drivers/firmware/qcom_scm.h
-@@ -80,6 +80,7 @@ extern int scm_legacy_call(struct device
- #define QCOM_SCM_SVC_BOOT 0x01
- #define QCOM_SCM_BOOT_SET_ADDR 0x01
- #define QCOM_SCM_BOOT_TERMINATE_PC 0x02
-+#define QCOM_SCM_BOOT_SDI_CONFIG 0x09
- #define QCOM_SCM_BOOT_SET_DLOAD_MODE 0x10
- #define QCOM_SCM_BOOT_SET_ADDR_MC 0x11
- #define QCOM_SCM_BOOT_SET_REMOTE_STATE 0x0a
diff --git a/target/linux/qualcommax/patches-6.12/0021-v6.7-dt-bindings-qcom-scm-document-IPQ5018-compatible.patch b/target/linux/qualcommax/patches-6.12/0021-v6.7-dt-bindings-qcom-scm-document-IPQ5018-compatible.patch
deleted file mode 100644
index d36ccddd27..0000000000
--- a/target/linux/qualcommax/patches-6.12/0021-v6.7-dt-bindings-qcom-scm-document-IPQ5018-compatible.patch
+++ /dev/null
@@ -1,25 +0,0 @@
-From f6aa7386bc40b552eea8ec1b1d2168afe3b31110 Mon Sep 17 00:00:00 2001
-From: Robert Marko <robimarko at gmail.com>
-Date: Wed, 16 Aug 2023 18:45:40 +0200
-Subject: [PATCH] dt-bindings: firmware: qcom,scm: document IPQ5018 compatible
-
-It seems that IPQ5018 compatible was never documented in the bindings.
-
-Signed-off-by: Robert Marko <robimarko at gmail.com>
-Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski at linaro.org>
-Link: https://lore.kernel.org/r/20230816164641.3371878-3-robimarko@gmail.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- Documentation/devicetree/bindings/firmware/qcom,scm.yaml | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
-+++ b/Documentation/devicetree/bindings/firmware/qcom,scm.yaml
-@@ -24,6 +24,7 @@ properties:
- - qcom,scm-apq8064
- - qcom,scm-apq8084
- - qcom,scm-ipq4019
-+ - qcom,scm-ipq5018
- - qcom,scm-ipq5332
- - qcom,scm-ipq6018
- - qcom,scm-ipq806x
diff --git a/target/linux/qualcommax/patches-6.12/0022-v6.7-arm64-dts-qcom-IPQ5018-indicate-that-SDI-shoud-be-disabled.patch b/target/linux/qualcommax/patches-6.12/0022-v6.7-arm64-dts-qcom-IPQ5018-indicate-that-SDI-shoud-be-disabled.patch
deleted file mode 100644
index 6d598bf50f..0000000000
--- a/target/linux/qualcommax/patches-6.12/0022-v6.7-arm64-dts-qcom-IPQ5018-indicate-that-SDI-shoud-be-disabled.patch
+++ /dev/null
@@ -1,26 +0,0 @@
-From 79796e87215db9587d6c66ec6f6781e091bc6464 Mon Sep 17 00:00:00 2001
-From: Robert Marko <robimarko at gmail.com>
-Date: Wed, 16 Aug 2023 18:45:41 +0200
-Subject: [PATCH] arm64: dts: qcom: ipq5018: indicate that SDI should be
- disabled
-
-Now that SCM has support for indicating that SDI has been enabled by
-default, lets set the property so SCM disables it during probing.
-
-Signed-off-by: Robert Marko <robimarko at gmail.com>
-Link: https://lore.kernel.org/r/20230816164641.3371878-4-robimarko@gmail.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- arch/arm64/boot/dts/qcom/ipq5018.dtsi | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
-+++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
-@@ -57,6 +57,7 @@
- firmware {
- scm {
- compatible = "qcom,scm-ipq5018", "qcom,scm";
-+ qcom,sdi-enabled;
- };
- };
-
diff --git a/target/linux/qualcommax/patches-6.12/0023-v6.7-dt-bindings-phy-qcom-m31-Add-IPQ5018-compatible.patch b/target/linux/qualcommax/patches-6.12/0023-v6.7-dt-bindings-phy-qcom-m31-Add-IPQ5018-compatible.patch
deleted file mode 100644
index 777212249e..0000000000
--- a/target/linux/qualcommax/patches-6.12/0023-v6.7-dt-bindings-phy-qcom-m31-Add-IPQ5018-compatible.patch
+++ /dev/null
@@ -1,28 +0,0 @@
-From 1852dfaacd3f4358bbfca134b63a02bbb30c1136 Mon Sep 17 00:00:00 2001
-From: Nitheesh Sekar <quic_nsekar at quicinc.com>
-Date: Mon, 4 Sep 2023 12:06:32 +0530
-Subject: [PATCH] dt-bindings: phy: qcom,m31: Add IPQ5018 compatible
-
-IPQ5332 qcom,m31 phy driver can support IPQ5018.
-
-Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski at linaro.org>
-Signed-off-by: Nitheesh Sekar <quic_nsekar at quicinc.com>
-Link: https://lore.kernel.org/r/20230904063635.24975-2-quic_nsekar@quicinc.com
-Signed-off-by: Vinod Koul <vkoul at kernel.org>
----
- .../devicetree/bindings/phy/qcom,ipq5332-usb-hsphy.yaml | 4 +++-
- 1 file changed, 3 insertions(+), 1 deletion(-)
-
---- a/Documentation/devicetree/bindings/phy/qcom,ipq5332-usb-hsphy.yaml
-+++ b/Documentation/devicetree/bindings/phy/qcom,ipq5332-usb-hsphy.yaml
-@@ -17,7 +17,9 @@ description:
- properties:
- compatible:
- items:
-- - const: qcom,ipq5332-usb-hsphy
-+ - enum:
-+ - qcom,ipq5018-usb-hsphy
-+ - qcom,ipq5332-usb-hsphy
-
- "#phy-cells":
- const: 0
diff --git a/target/linux/qualcommax/patches-6.12/0024-v6.7-phy-qcom-m31-Add-compatible-phy-init-sequence-for-IPQ5018.patch b/target/linux/qualcommax/patches-6.12/0024-v6.7-phy-qcom-m31-Add-compatible-phy-init-sequence-for-IPQ5018.patch
deleted file mode 100644
index 248b47c694..0000000000
--- a/target/linux/qualcommax/patches-6.12/0024-v6.7-phy-qcom-m31-Add-compatible-phy-init-sequence-for-IPQ5018.patch
+++ /dev/null
@@ -1,89 +0,0 @@
-From 68320e35f8cb1987b4ad34347fc7033832da99e3 Mon Sep 17 00:00:00 2001
-From: Nitheesh Sekar <quic_nsekar at quicinc.com>
-Date: Mon, 4 Sep 2023 12:06:33 +0530
-Subject: [PATCH] phy: qcom-m31: Add compatible, phy init sequence for IPQ5018
-
-Add phy init sequence and compatible string for IPQ5018
-chipset.
-
-Signed-off-by: Nitheesh Sekar <quic_nsekar at quicinc.com>
-Link: https://lore.kernel.org/r/20230904063635.24975-3-quic_nsekar@quicinc.com
-Signed-off-by: Vinod Koul <vkoul at kernel.org>
----
- drivers/phy/qualcomm/phy-qcom-m31.c | 51 +++++++++++++++++++++++++++++
- 1 file changed, 51 insertions(+)
-
---- a/drivers/phy/qualcomm/phy-qcom-m31.c
-+++ b/drivers/phy/qualcomm/phy-qcom-m31.c
-@@ -82,6 +82,50 @@ struct m31_priv_data {
- unsigned int nregs;
- };
-
-+static const struct m31_phy_regs m31_ipq5018_regs[] = {
-+ {
-+ .off = USB_PHY_CFG0,
-+ .val = UTMI_PHY_OVERRIDE_EN
-+ },
-+ {
-+ .off = USB_PHY_UTMI_CTRL5,
-+ .val = POR_EN,
-+ .delay = 15
-+ },
-+ {
-+ .off = USB_PHY_FSEL_SEL,
-+ .val = FREQ_SEL
-+ },
-+ {
-+ .off = USB_PHY_HS_PHY_CTRL_COMMON0,
-+ .val = COMMONONN | FSEL | RETENABLEN
-+ },
-+ {
-+ .off = USB_PHY_REFCLK_CTRL,
-+ .val = CLKCORE
-+ },
-+ {
-+ .off = USB_PHY_UTMI_CTRL5,
-+ .val = POR_EN
-+ },
-+ {
-+ .off = USB_PHY_HS_PHY_CTRL2,
-+ .val = USB2_SUSPEND_N_SEL | USB2_SUSPEND_N | USB2_UTMI_CLK_EN
-+ },
-+ {
-+ .off = USB_PHY_UTMI_CTRL5,
-+ .val = 0x0
-+ },
-+ {
-+ .off = USB_PHY_HS_PHY_CTRL2,
-+ .val = USB2_SUSPEND_N | USB2_UTMI_CLK_EN
-+ },
-+ {
-+ .off = USB_PHY_CFG0,
-+ .val = 0x0
-+ },
-+};
-+
- static struct m31_phy_regs m31_ipq5332_regs[] = {
- {
- USB_PHY_CFG0,
-@@ -267,6 +311,12 @@ static int m31usb_phy_probe(struct platf
- return PTR_ERR_OR_ZERO(phy_provider);
- }
-
-+static const struct m31_priv_data m31_ipq5018_data = {
-+ .ulpi_mode = false,
-+ .regs = m31_ipq5018_regs,
-+ .nregs = ARRAY_SIZE(m31_ipq5018_regs),
-+};
-+
- static const struct m31_priv_data m31_ipq5332_data = {
- .ulpi_mode = false,
- .regs = m31_ipq5332_regs,
-@@ -274,6 +324,7 @@ static const struct m31_priv_data m31_ip
- };
-
- static const struct of_device_id m31usb_phy_id_table[] = {
-+ { .compatible = "qcom,ipq5018-usb-hsphy", .data = &m31_ipq5018_data },
- { .compatible = "qcom,ipq5332-usb-hsphy", .data = &m31_ipq5332_data },
- { },
- };
diff --git a/target/linux/qualcommax/patches-6.12/0025-v6.7-dt-bindings-usb-dwc3-Add-IPQ5018-compatible.patch b/target/linux/qualcommax/patches-6.12/0025-v6.7-dt-bindings-usb-dwc3-Add-IPQ5018-compatible.patch
deleted file mode 100644
index 146fcbff09..0000000000
--- a/target/linux/qualcommax/patches-6.12/0025-v6.7-dt-bindings-usb-dwc3-Add-IPQ5018-compatible.patch
+++ /dev/null
@@ -1,41 +0,0 @@
-From 3865a64284cc4845c61cf3dc6c7246349d80cc49 Mon Sep 17 00:00:00 2001
-From: Nitheesh Sekar <quic_nsekar at quicinc.com>
-Date: Thu, 31 Aug 2023 08:35:03 +0530
-Subject: [PATCH] dt-bindings: usb: dwc3: Add IPQ5018 compatible
-
-Document the IPQ5018 dwc3 compatible.
-
-Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski at linaro.org>
-Signed-off-by: Nitheesh Sekar <quic_nsekar at quicinc.com>
-Link: https://lore.kernel.org/r/20230831030503.17100-1-quic_nsekar@quicinc.com
-Signed-off-by: Greg Kroah-Hartman <gregkh at linuxfoundation.org>
----
- Documentation/devicetree/bindings/usb/qcom,dwc3.yaml | 3 +++
- 1 file changed, 3 insertions(+)
-
---- a/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
-+++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
-@@ -14,6 +14,7 @@ properties:
- items:
- - enum:
- - qcom,ipq4019-dwc3
-+ - qcom,ipq5018-dwc3
- - qcom,ipq5332-dwc3
- - qcom,ipq6018-dwc3
- - qcom,ipq8064-dwc3
-@@ -238,6 +239,7 @@ allOf:
- compatible:
- contains:
- enum:
-+ - qcom,ipq5018-dwc3
- - qcom,ipq5332-dwc3
- - qcom,msm8994-dwc3
- - qcom,qcs404-dwc3
-@@ -411,6 +413,7 @@ allOf:
- compatible:
- contains:
- enum:
-+ - qcom,ipq5018-dwc3
- - qcom,ipq5332-dwc3
- - qcom,sdm660-dwc3
- then:
diff --git a/target/linux/qualcommax/patches-6.12/0026-v6.8-arm64-dts-qcom-ipq5018-Add-USB-related-nodes.patch b/target/linux/qualcommax/patches-6.12/0026-v6.8-arm64-dts-qcom-ipq5018-Add-USB-related-nodes.patch
deleted file mode 100644
index 99fdae732a..0000000000
--- a/target/linux/qualcommax/patches-6.12/0026-v6.8-arm64-dts-qcom-ipq5018-Add-USB-related-nodes.patch
+++ /dev/null
@@ -1,86 +0,0 @@
-From e7166f2774aafefd29ff26ffbbb7f6d40ac8ea1c Mon Sep 17 00:00:00 2001
-From: Nitheesh Sekar <quic_nsekar at quicinc.com>
-Date: Mon, 4 Sep 2023 12:06:34 +0530
-Subject: [PATCH] arm64: dts: qcom: ipq5018: Add USB related nodes
-
-Add USB phy and controller nodes.
-
-Co-developed-by: Amandeep Singh <quic_amansing at quicinc.com>
-Signed-off-by: Amandeep Singh <quic_amansing at quicinc.com>
-Signed-off-by: Nitheesh Sekar <quic_nsekar at quicinc.com>
-Link: https://lore.kernel.org/r/20230904063635.24975-4-quic_nsekar@quicinc.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- arch/arm64/boot/dts/qcom/ipq5018.dtsi | 54 +++++++++++++++++++++++++++
- 1 file changed, 54 insertions(+)
-
---- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
-+++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
-@@ -94,6 +94,19 @@
- #size-cells = <1>;
- ranges = <0 0 0 0xffffffff>;
-
-+ usbphy0: phy at 5b000 {
-+ compatible = "qcom,ipq5018-usb-hsphy";
-+ reg = <0x0005b000 0x120>;
-+
-+ clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>;
-+
-+ resets = <&gcc GCC_QUSB2_0_PHY_BCR>;
-+
-+ #phy-cells = <0>;
-+
-+ status = "disabled";
-+ };
-+
- tlmm: pinctrl at 1000000 {
- compatible = "qcom,ipq5018-tlmm";
- reg = <0x01000000 0x300000>;
-@@ -156,6 +169,47 @@
- status = "disabled";
- };
-
-+ usb: usb at 8af8800 {
-+ compatible = "qcom,ipq5018-dwc3", "qcom,dwc3";
-+ reg = <0x08af8800 0x400>;
-+
-+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
-+ interrupt-names = "hs_phy_irq";
-+
-+ clocks = <&gcc GCC_USB0_MASTER_CLK>,
-+ <&gcc GCC_SYS_NOC_USB0_AXI_CLK>,
-+ <&gcc GCC_USB0_SLEEP_CLK>,
-+ <&gcc GCC_USB0_MOCK_UTMI_CLK>;
-+ clock-names = "core",
-+ "iface",
-+ "sleep",
-+ "mock_utmi";
-+
-+ resets = <&gcc GCC_USB0_BCR>;
-+
-+ qcom,select-utmi-as-pipe-clk;
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+ ranges;
-+
-+ status = "disabled";
-+
-+ usb_dwc: usb at 8a00000 {
-+ compatible = "snps,dwc3";
-+ reg = <0x08a00000 0xe000>;
-+ clocks = <&gcc GCC_USB0_MOCK_UTMI_CLK>;
-+ clock-names = "ref";
-+ interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
-+ phy-names = "usb2-phy";
-+ phys = <&usbphy0>;
-+ tx-fifo-resize;
-+ snps,is-utmi-l1-suspend;
-+ snps,hird-threshold = /bits/ 8 <0x0>;
-+ snps,dis_u2_susphy_quirk;
-+ snps,dis_u3_susphy_quirk;
-+ };
-+ };
-+
- intc: interrupt-controller at b000000 {
- compatible = "qcom,msm-qgic2";
- reg = <0x0b000000 0x1000>, /* GICD */
diff --git a/target/linux/qualcommax/patches-6.12/0027-v6.8-arm64-dts-qcom-ipq5018-add-QUP1-SPI-controller.patch b/target/linux/qualcommax/patches-6.12/0027-v6.8-arm64-dts-qcom-ipq5018-add-QUP1-SPI-controller.patch
deleted file mode 100644
index d0d9e45dec..0000000000
--- a/target/linux/qualcommax/patches-6.12/0027-v6.8-arm64-dts-qcom-ipq5018-add-QUP1-SPI-controller.patch
+++ /dev/null
@@ -1,56 +0,0 @@
-From a1f42e08f0f04b72a6597f080db4bfbb3737910c Mon Sep 17 00:00:00 2001
-From: Robert Marko <robimarko at gmail.com>
-Date: Wed, 4 Oct 2023 21:12:30 +0200
-Subject: [PATCH] arm64: dts: qcom: ipq5018: add QUP1 SPI controller
-
-Add the required BAM and QUP nodes for the QUP1 SPI controller on IPQ5018.
-
-Signed-off-by: Robert Marko <robimarko at gmail.com>
-Reviewed-by: Kathiravan Thirumoorthy <quic_kathirav at quicinc.com>
-Link: https://lore.kernel.org/r/20231004191303.331055-1-robimarko@gmail.com
-[bjorn: Padded address to 8 digits, fixed node sort order]
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- arch/arm64/boot/dts/qcom/ipq5018.dtsi | 24 ++++++++++++++++++++++++
- 1 file changed, 24 insertions(+)
-
---- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
-+++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
-@@ -159,6 +159,16 @@
- status = "disabled";
- };
-
-+ blsp_dma: dma-controller at 7884000 {
-+ compatible = "qcom,bam-v1.7.0";
-+ reg = <0x07884000 0x1d000>;
-+ interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
-+ clocks = <&gcc GCC_BLSP1_AHB_CLK>;
-+ clock-names = "bam_clk";
-+ #dma-cells = <1>;
-+ qcom,ee = <0>;
-+ };
-+
- blsp1_uart1: serial at 78af000 {
- compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
- reg = <0x078af000 0x200>;
-@@ -169,6 +179,20 @@
- status = "disabled";
- };
-
-+ blsp1_spi1: spi at 78b5000 {
-+ compatible = "qcom,spi-qup-v2.2.1";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <0x078b5000 0x600>;
-+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
-+ clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
-+ <&gcc GCC_BLSP1_AHB_CLK>;
-+ clock-names = "core", "iface";
-+ dmas = <&blsp_dma 4>, <&blsp_dma 5>;
-+ dma-names = "tx", "rx";
-+ status = "disabled";
-+ };
-+
- usb: usb at 8af8800 {
- compatible = "qcom,ipq5018-dwc3", "qcom,dwc3";
- reg = <0x08af8800 0x400>;
diff --git a/target/linux/qualcommax/patches-6.12/0028-v6.8-dt-bindings-clock-qcom-a53pll-add-IPQ5018-compatible.patch b/target/linux/qualcommax/patches-6.12/0028-v6.8-dt-bindings-clock-qcom-a53pll-add-IPQ5018-compatible.patch
deleted file mode 100644
index 314afa76d2..0000000000
--- a/target/linux/qualcommax/patches-6.12/0028-v6.8-dt-bindings-clock-qcom-a53pll-add-IPQ5018-compatible.patch
+++ /dev/null
@@ -1,25 +0,0 @@
-From 4d45d56e17348c6b6bb2bce126a4a5ea97b19900 Mon Sep 17 00:00:00 2001
-From: Gokul Sriram Palanisamy <quic_gokulsri at quicinc.com>
-Date: Mon, 25 Sep 2023 15:58:24 +0530
-Subject: [PATCH] dt-bindings: clock: qcom,a53pll: add IPQ5018 compatible
-
-Add IPQ5018 compatible to A53 PLL bindings.
-
-Signed-off-by: Gokul Sriram Palanisamy <quic_gokulsri at quicinc.com>
-Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski at linaro.org>
-Link: https://lore.kernel.org/r/20230925102826.405446-2-quic_gokulsri@quicinc.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- Documentation/devicetree/bindings/clock/qcom,a53pll.yaml | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/Documentation/devicetree/bindings/clock/qcom,a53pll.yaml
-+++ b/Documentation/devicetree/bindings/clock/qcom,a53pll.yaml
-@@ -16,6 +16,7 @@ description:
- properties:
- compatible:
- enum:
-+ - qcom,ipq5018-a53pll
- - qcom,ipq5332-a53pll
- - qcom,ipq6018-a53pll
- - qcom,ipq8074-a53pll
diff --git a/target/linux/qualcommax/patches-6.12/0029-v6.8-clk-qcom-apss-ipq-pll-add-support-for-IPQ5018.patch b/target/linux/qualcommax/patches-6.12/0029-v6.8-clk-qcom-apss-ipq-pll-add-support-for-IPQ5018.patch
deleted file mode 100644
index 46dede07ca..0000000000
--- a/target/linux/qualcommax/patches-6.12/0029-v6.8-clk-qcom-apss-ipq-pll-add-support-for-IPQ5018.patch
+++ /dev/null
@@ -1,62 +0,0 @@
-From 50492f929486c044b43cb3e2c0e040aa9b61ea2b Mon Sep 17 00:00:00 2001
-From: Gokul Sriram Palanisamy <quic_gokulsri at quicinc.com>
-Date: Mon, 25 Sep 2023 15:58:25 +0530
-Subject: [PATCH] clk: qcom: apss-ipq-pll: add support for IPQ5018
-
-IPQ5018 APSS PLL is of type Stromer. Reuse Stromer Plus PLL offsets,
-add configuration values and the compatible.
-
-Co-developed-by: Sricharan Ramabadhran <quic_srichara at quicinc.com>
-Signed-off-by: Sricharan Ramabadhran <quic_srichara at quicinc.com>
-Signed-off-by: Gokul Sriram Palanisamy <quic_gokulsri at quicinc.com>
-Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
-Link: https://lore.kernel.org/r/20230925102826.405446-3-quic_gokulsri@quicinc.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- drivers/clk/qcom/apss-ipq-pll.c | 21 +++++++++++++++++++++
- 1 file changed, 21 insertions(+)
-
---- a/drivers/clk/qcom/apss-ipq-pll.c
-+++ b/drivers/clk/qcom/apss-ipq-pll.c
-@@ -73,6 +73,20 @@ static struct clk_alpha_pll ipq_pll_stro
- },
- };
-
-+static const struct alpha_pll_config ipq5018_pll_config = {
-+ .l = 0x32,
-+ .config_ctl_val = 0x4001075b,
-+ .config_ctl_hi_val = 0x304,
-+ .main_output_mask = BIT(0),
-+ .aux_output_mask = BIT(1),
-+ .early_output_mask = BIT(3),
-+ .alpha_en_mask = BIT(24),
-+ .status_val = 0x3,
-+ .status_mask = GENMASK(10, 8),
-+ .lock_det = BIT(2),
-+ .test_ctl_hi_val = 0x00400003,
-+};
-+
- static const struct alpha_pll_config ipq5332_pll_config = {
- .l = 0x2d,
- .config_ctl_val = 0x4001075b,
-@@ -129,6 +143,12 @@ struct apss_pll_data {
- const struct alpha_pll_config *pll_config;
- };
-
-+static const struct apss_pll_data ipq5018_pll_data = {
-+ .pll_type = CLK_ALPHA_PLL_TYPE_STROMER_PLUS,
-+ .pll = &ipq_pll_stromer_plus,
-+ .pll_config = &ipq5018_pll_config,
-+};
-+
- static struct apss_pll_data ipq5332_pll_data = {
- .pll_type = CLK_ALPHA_PLL_TYPE_STROMER_PLUS,
- .pll = &ipq_pll_stromer_plus,
-@@ -195,6 +215,7 @@ static int apss_ipq_pll_probe(struct pla
- }
-
- static const struct of_device_id apss_ipq_pll_match_table[] = {
-+ { .compatible = "qcom,ipq5018-a53pll", .data = &ipq5018_pll_data },
- { .compatible = "qcom,ipq5332-a53pll", .data = &ipq5332_pll_data },
- { .compatible = "qcom,ipq6018-a53pll", .data = &ipq6018_pll_data },
- { .compatible = "qcom,ipq8074-a53pll", .data = &ipq8074_pll_data },
diff --git a/target/linux/qualcommax/patches-6.12/0030-v6.8-arm64-dts-qcom-ipq5018-enable-the-CPUFreq-support.patch b/target/linux/qualcommax/patches-6.12/0030-v6.8-arm64-dts-qcom-ipq5018-enable-the-CPUFreq-support.patch
deleted file mode 100644
index 72bec54cb3..0000000000
--- a/target/linux/qualcommax/patches-6.12/0030-v6.8-arm64-dts-qcom-ipq5018-enable-the-CPUFreq-support.patch
+++ /dev/null
@@ -1,98 +0,0 @@
-From 3e4b53e04281ed3d9c7a4329c027097265c04d54 Mon Sep 17 00:00:00 2001
-From: Gokul Sriram Palanisamy <quic_gokulsri at quicinc.com>
-Date: Mon, 25 Sep 2023 15:58:26 +0530
-Subject: [PATCH] arm64: dts: qcom: ipq5018: enable the CPUFreq support
-
-Add the APCS, A53 PLL, cpu-opp-table nodes to set
-the CPU frequency at 800MHz (idle) or 1.008GHz.
-
-Co-developed-by: Sricharan Ramabadhran <quic_srichara at quicinc.com>
-Signed-off-by: Sricharan Ramabadhran <quic_srichara at quicinc.com>
-Signed-off-by: Gokul Sriram Palanisamy <quic_gokulsri at quicinc.com>
-Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
-Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski at linaro.org>
-Link: https://lore.kernel.org/r/20230925102826.405446-4-quic_gokulsri@quicinc.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- arch/arm64/boot/dts/qcom/ipq5018.dtsi | 40 +++++++++++++++++++++++++++
- 1 file changed, 40 insertions(+)
-
---- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
-+++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
-@@ -5,6 +5,7 @@
- * Copyright (c) 2023 The Linux Foundation. All rights reserved.
- */
-
-+#include <dt-bindings/clock/qcom,apss-ipq.h>
- #include <dt-bindings/interrupt-controller/arm-gic.h>
- #include <dt-bindings/clock/qcom,gcc-ipq5018.h>
- #include <dt-bindings/reset/qcom,gcc-ipq5018.h>
-@@ -36,6 +37,8 @@
- reg = <0x0>;
- enable-method = "psci";
- next-level-cache = <&L2_0>;
-+ clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
-+ operating-points-v2 = <&cpu_opp_table>;
- };
-
- CPU1: cpu at 1 {
-@@ -44,6 +47,8 @@
- reg = <0x1>;
- enable-method = "psci";
- next-level-cache = <&L2_0>;
-+ clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
-+ operating-points-v2 = <&cpu_opp_table>;
- };
-
- L2_0: l2-cache {
-@@ -54,6 +59,25 @@
- };
- };
-
-+ cpu_opp_table: opp-table-cpu {
-+ compatible = "operating-points-v2";
-+ opp-shared;
-+
-+ /*
-+ opp-800000000 {
-+ opp-hz = /bits/ 64 <800000000>;
-+ opp-microvolt = <1100000>;
-+ clock-latency-ns = <200000>;
-+ };
-+ */
-+
-+ opp-1008000000 {
-+ opp-hz = /bits/ 64 <1008000000>;
-+ opp-microvolt = <1100000>;
-+ clock-latency-ns = <200000>;
-+ };
-+ };
-+
- firmware {
- scm {
- compatible = "qcom,scm-ipq5018", "qcom,scm";
-@@ -267,6 +291,24 @@
- clocks = <&sleep_clk>;
- };
-
-+ apcs_glb: mailbox at b111000 {
-+ compatible = "qcom,ipq5018-apcs-apps-global",
-+ "qcom,ipq6018-apcs-apps-global";
-+ reg = <0x0b111000 0x1000>;
-+ #clock-cells = <1>;
-+ clocks = <&a53pll>, <&xo_board_clk>, <&gcc GPLL0>;
-+ clock-names = "pll", "xo", "gpll0";
-+ #mbox-cells = <1>;
-+ };
-+
-+ a53pll: clock at b116000 {
-+ compatible = "qcom,ipq5018-a53pll";
-+ reg = <0x0b116000 0x40>;
-+ #clock-cells = <0>;
-+ clocks = <&xo_board_clk>;
-+ clock-names = "xo";
-+ };
-+
- timer at b120000 {
- compatible = "arm,armv7-timer-mem";
- reg = <0x0b120000 0x1000>;
diff --git a/target/linux/qualcommax/patches-6.12/0031-v6.8-arm64-dts-qcom-ipq5018-add-few-more-reserved-memory-regions.patch b/target/linux/qualcommax/patches-6.12/0031-v6.8-arm64-dts-qcom-ipq5018-add-few-more-reserved-memory-regions.patch
deleted file mode 100644
index 97631e715a..0000000000
--- a/target/linux/qualcommax/patches-6.12/0031-v6.8-arm64-dts-qcom-ipq5018-add-few-more-reserved-memory-regions.patch
+++ /dev/null
@@ -1,66 +0,0 @@
-From a427dd16e61f3d145bc24f0ed09692fc25931250 Mon Sep 17 00:00:00 2001
-From: Kathiravan Thirumoorthy <quic_kathirav at quicinc.com>
-Date: Wed, 25 Oct 2023 22:12:12 +0530
-Subject: [PATCH] arm64: dts: qcom: ipq5018: add few more reserved memory
- regions
-
-Like all other IPQ SoCs, bootloader will collect the system RAM contents
-upon crash for the post morterm analysis. If we don't reserve the memory
-region used by bootloader, obviously linux will consume it and upon next
-boot on crash, bootloader will be loaded in the same region, which will
-lead to loose some of the data, sometimes we may miss out critical
-information. So lets reserve the region used by the bootloader.
-
-Similarly SBL copies some data into the reserved region and it will be
-used in the crash scenario. So reserve 1MB for SBL as well.
-
-While at it, enable the SMEM support along with TCSR mutex.
-
-Signed-off-by: Kathiravan Thirumoorthy <quic_kathirav at quicinc.com>
-Reviewed-by: Konrad Dybcio <konrad.dybcio at linaro.org>
-Link: https://lore.kernel.org/r/20231025-ipq5018-misc-v1-1-7d14fde97fe7@quicinc.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- arch/arm64/boot/dts/qcom/ipq5018.dtsi | 24 ++++++++++++++++++++++++
- 1 file changed, 24 insertions(+)
-
---- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
-+++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
-@@ -106,6 +106,24 @@
- #size-cells = <2>;
- ranges;
-
-+ bootloader at 4a800000 {
-+ reg = <0x0 0x4a800000 0x0 0x200000>;
-+ no-map;
-+ };
-+
-+ sbl at 4aa00000 {
-+ reg = <0x0 0x4aa00000 0x0 0x100000>;
-+ no-map;
-+ };
-+
-+ smem at 4ab00000 {
-+ compatible = "qcom,smem";
-+ reg = <0x0 0x4ab00000 0x0 0x100000>;
-+ no-map;
-+
-+ hwlocks = <&tcsr_mutex 3>;
-+ };
-+
- tz_region: tz at 4ac00000 {
- reg = <0x0 0x4ac00000 0x0 0x200000>;
- no-map;
-@@ -166,6 +184,12 @@
- #power-domain-cells = <1>;
- };
-
-+ tcsr_mutex: hwlock at 1905000 {
-+ compatible = "qcom,tcsr-mutex";
-+ reg = <0x01905000 0x20000>;
-+ #hwlock-cells = <1>;
-+ };
-+
- sdhc_1: mmc at 7804000 {
- compatible = "qcom,ipq5018-sdhci", "qcom,sdhci-msm-v5";
- reg = <0x7804000 0x1000>;
diff --git a/target/linux/qualcommax/patches-6.12/0032-v6.10-clk-qcom-apss-ipq-pll-use-stromer-ops-for-IPQ5018-to-fix-boot-failure.patch b/target/linux/qualcommax/patches-6.12/0032-v6.10-clk-qcom-apss-ipq-pll-use-stromer-ops-for-IPQ5018-to-fix-boot-failure.patch
deleted file mode 100644
index ea6f61b57f..0000000000
--- a/target/linux/qualcommax/patches-6.12/0032-v6.10-clk-qcom-apss-ipq-pll-use-stromer-ops-for-IPQ5018-to-fix-boot-failure.patch
+++ /dev/null
@@ -1,83 +0,0 @@
-From: Gabor Juhos <j4g8y7 at gmail.com>
-Subject: [PATCH] clk: qcom: apss-ipq-pll: use stromer ops for IPQ5018 to fix boot failure
-Date: Fri, 15 Mar 2024 17:16:41 +0100
-
-Booting v6.8 results in a hang on various IPQ5018 based boards.
-Investigating the problem showed that the hang happens when the
-clk_alpha_pll_stromer_plus_set_rate() function tries to write
-into the PLL_MODE register of the APSS PLL.
-
-Checking the downstream code revealed that it uses [1] stromer
-specific operations for IPQ5018, whereas in the current code
-the stromer plus specific operations are used.
-
-The ops in the 'ipq_pll_stromer_plus' clock definition can't be
-changed since that is needed for IPQ5332, so add a new alpha pll
-clock declaration which uses the correct stromer ops and use this
-new clock for IPQ5018 to avoid the boot failure.
-
-Also, change pll_type in 'ipq5018_pll_data' to
-CLK_ALPHA_PLL_TYPE_STROMER to better reflect that it is a Stromer
-PLL and change the apss_ipq_pll_probe() function accordingly.
-
-1. https://git.codelinaro.org/clo/qsdk/oss/kernel/linux-ipq-5.4/-/blob/NHSS.QSDK.12.4/drivers/clk/qcom/apss-ipq5018.c#L67
-
-Fixes: 50492f929486 ("clk: qcom: apss-ipq-pll: add support for IPQ5018")
-Signed-off-by: Gabor Juhos <j4g8y7 at gmail.com>
----
- drivers/clk/qcom/apss-ipq-pll.c | 30 +++++++++++++++++++++++++++---
- 1 file changed, 27 insertions(+), 3 deletions(-)
-
---- a/drivers/clk/qcom/apss-ipq-pll.c
-+++ b/drivers/clk/qcom/apss-ipq-pll.c
-@@ -55,6 +55,29 @@ static struct clk_alpha_pll ipq_pll_huay
- },
- };
-
-+static struct clk_alpha_pll ipq_pll_stromer = {
-+ .offset = 0x0,
-+ /*
-+ * Reuse CLK_ALPHA_PLL_TYPE_STROMER_PLUS register offsets.
-+ * Although this is a bit confusing, but the offset values
-+ * are correct nevertheless.
-+ */
-+ .regs = ipq_pll_offsets[CLK_ALPHA_PLL_TYPE_STROMER_PLUS],
-+ .flags = SUPPORTS_DYNAMIC_UPDATE,
-+ .clkr = {
-+ .enable_reg = 0x0,
-+ .enable_mask = BIT(0),
-+ .hw.init = &(const struct clk_init_data) {
-+ .name = "a53pll",
-+ .parent_data = &(const struct clk_parent_data) {
-+ .fw_name = "xo",
-+ },
-+ .num_parents = 1,
-+ .ops = &clk_alpha_pll_stromer_ops,
-+ },
-+ },
-+};
-+
- static struct clk_alpha_pll ipq_pll_stromer_plus = {
- .offset = 0x0,
- .regs = ipq_pll_offsets[CLK_ALPHA_PLL_TYPE_STROMER_PLUS],
-@@ -144,8 +167,8 @@ struct apss_pll_data {
- };
-
- static const struct apss_pll_data ipq5018_pll_data = {
-- .pll_type = CLK_ALPHA_PLL_TYPE_STROMER_PLUS,
-- .pll = &ipq_pll_stromer_plus,
-+ .pll_type = CLK_ALPHA_PLL_TYPE_STROMER,
-+ .pll = &ipq_pll_stromer,
- .pll_config = &ipq5018_pll_config,
- };
-
-@@ -203,7 +226,8 @@ static int apss_ipq_pll_probe(struct pla
-
- if (data->pll_type == CLK_ALPHA_PLL_TYPE_HUAYRA)
- clk_alpha_pll_configure(data->pll, regmap, data->pll_config);
-- else if (data->pll_type == CLK_ALPHA_PLL_TYPE_STROMER_PLUS)
-+ else if (data->pll_type == CLK_ALPHA_PLL_TYPE_STROMER ||
-+ data->pll_type == CLK_ALPHA_PLL_TYPE_STROMER_PLUS)
- clk_stromer_pll_configure(data->pll, regmap, data->pll_config);
-
- ret = devm_clk_register_regmap(dev, &data->pll->clkr);
diff --git a/target/linux/qualcommax/patches-6.12/0033-v6.10-clk-qcom-apss-ipq-pll-fix-PLL-rate-for-IPQ5018.patch b/target/linux/qualcommax/patches-6.12/0033-v6.10-clk-qcom-apss-ipq-pll-fix-PLL-rate-for-IPQ5018.patch
deleted file mode 100644
index 4bf0598c36..0000000000
--- a/target/linux/qualcommax/patches-6.12/0033-v6.10-clk-qcom-apss-ipq-pll-fix-PLL-rate-for-IPQ5018.patch
+++ /dev/null
@@ -1,32 +0,0 @@
-From: Gabor Juhos <j4g8y7 at gmail.com>
-Subject: [PATCH] clk: qcom: apss-ipq-pll: fix PLL rate for IPQ5018
-Date: Tue, 26 Mar 2024 14:34:11 +0100
-
-According to ipq5018.dtsi, the maximum supported rate by the
-CPU is 1.008 GHz on the IPQ5018 platform, however the current
-configuration of the PLL results in 1.2 GHz rate.
-
-Change the 'L' value in the PLL configuration to limit the
-rate to 1.008 GHz. The downstream kernel also uses the same
-value [1]. Also add a comment to indicate the desired
-frequency.
-
-[1] https://git.codelinaro.org/clo/qsdk/oss/kernel/linux-ipq-5.4/-/blob/NHSS.QSDK.12.4/drivers/clk/qcom/apss-ipq5018.c?ref_type=heads#L151
-
-Fixes: 50492f929486 ("clk: qcom: apss-ipq-pll: add support for IPQ5018")
-Signed-off-by: Gabor Juhos <j4g8y7 at gmail.com>
----
- drivers/clk/qcom/apss-ipq-pll.c | 3 ++-
- 1 file changed, 2 insertions(+), 1 deletion(-)
-
---- a/drivers/clk/qcom/apss-ipq-pll.c
-+++ b/drivers/clk/qcom/apss-ipq-pll.c
-@@ -97,7 +97,7 @@ static struct clk_alpha_pll ipq_pll_stro
- };
-
- static const struct alpha_pll_config ipq5018_pll_config = {
-- .l = 0x32,
-+ .l = 0x2a,
- .config_ctl_val = 0x4001075b,
- .config_ctl_hi_val = 0x304,
- .main_output_mask = BIT(0),
diff --git a/target/linux/qualcommax/patches-6.12/0034-v6.11-clk-qcom-gcc-ipq6018-update-sdcc-max-clock-frequency.patch b/target/linux/qualcommax/patches-6.12/0034-v6.11-clk-qcom-gcc-ipq6018-update-sdcc-max-clock-frequency.patch
deleted file mode 100644
index ddd54079fb..0000000000
--- a/target/linux/qualcommax/patches-6.12/0034-v6.11-clk-qcom-gcc-ipq6018-update-sdcc-max-clock-frequency.patch
+++ /dev/null
@@ -1,26 +0,0 @@
-From f2743ae3ff84579981ac513f512b9df945d109c0 Mon Sep 17 00:00:00 2001
-From: Chukun Pan <amadeus at jmu.edu.cn>
-Date: Thu, 20 Jun 2024 23:01:21 +0800
-Subject: [PATCH] clk: qcom: gcc-ipq6018: update sdcc max clock frequency
-
-The mmc controller of the IPQ6018 does not support HS400 mode.
-So adjust the maximum clock frequency of sdcc to 200 MHz (HS200).
-
-Signed-off-by: Chukun Pan <amadeus at jmu.edu.cn>
-Link: https://lore.kernel.org/r/20240620150122.1406631-2-amadeus@jmu.edu.cn
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- drivers/clk/qcom/gcc-ipq6018.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/clk/qcom/gcc-ipq6018.c
-+++ b/drivers/clk/qcom/gcc-ipq6018.c
-@@ -1617,7 +1617,7 @@ static const struct freq_tbl ftbl_sdcc_a
- F(96000000, P_GPLL2, 12, 0, 0),
- F(177777778, P_GPLL0, 4.5, 0, 0),
- F(192000000, P_GPLL2, 6, 0, 0),
-- F(384000000, P_GPLL2, 3, 0, 0),
-+ F(200000000, P_GPLL0, 4, 0, 0),
- { }
- };
-
diff --git a/target/linux/qualcommax/patches-6.12/0035-v6.11-arm64-dts-qcom-ipq6018-add-sdhci-node.patch b/target/linux/qualcommax/patches-6.12/0035-v6.11-arm64-dts-qcom-ipq6018-add-sdhci-node.patch
deleted file mode 100644
index ed4b6d9e6d..0000000000
--- a/target/linux/qualcommax/patches-6.12/0035-v6.11-arm64-dts-qcom-ipq6018-add-sdhci-node.patch
+++ /dev/null
@@ -1,47 +0,0 @@
-From 5db216f6e1f85394e79dca74ceceb83b2f8566b5 Mon Sep 17 00:00:00 2001
-From: Chukun Pan <amadeus at jmu.edu.cn>
-Date: Thu, 20 Jun 2024 23:01:22 +0800
-Subject: [PATCH] arm64: dts: qcom: ipq6018: add sdhci node
-
-Add node to support mmc controller inside of IPQ6018.
-This controller supports both eMMC and SD cards.
-
-Tested with:
- eMMC (HS200)
- SD Card (SDR50/SDR104)
-
-Signed-off-by: Chukun Pan <amadeus at jmu.edu.cn>
-Link: https://lore.kernel.org/r/20240620150122.1406631-3-amadeus@jmu.edu.cn
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- arch/arm64/boot/dts/qcom/ipq6018.dtsi | 19 +++++++++++++++++++
- 1 file changed, 19 insertions(+)
-
---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
-+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
-@@ -470,6 +470,25 @@
- };
- };
-
-+ sdhc: mmc at 7804000 {
-+ compatible = "qcom,ipq6018-sdhci", "qcom,sdhci-msm-v5";
-+ reg = <0x0 0x07804000 0x0 0x1000>,
-+ <0x0 0x07805000 0x0 0x1000>;
-+ reg-names = "hc", "cqhci";
-+
-+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
-+ <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
-+ interrupt-names = "hc_irq", "pwr_irq";
-+
-+ clocks = <&gcc GCC_SDCC1_AHB_CLK>,
-+ <&gcc GCC_SDCC1_APPS_CLK>,
-+ <&xo>;
-+ clock-names = "iface", "core", "xo";
-+ resets = <&gcc GCC_SDCC1_BCR>;
-+ max-frequency = <192000000>;
-+ status = "disabled";
-+ };
-+
- blsp_dma: dma-controller at 7884000 {
- compatible = "qcom,bam-v1.7.0";
- reg = <0x0 0x07884000 0x0 0x2b000>;
diff --git a/target/linux/qualcommax/patches-6.12/0042-v6.10-clk-qcom-clk-rcg-introduce-support-for-multiple-conf.patch b/target/linux/qualcommax/patches-6.12/0042-v6.10-clk-qcom-clk-rcg-introduce-support-for-multiple-conf.patch
deleted file mode 100644
index 937e644626..0000000000
--- a/target/linux/qualcommax/patches-6.12/0042-v6.10-clk-qcom-clk-rcg-introduce-support-for-multiple-conf.patch
+++ /dev/null
@@ -1,83 +0,0 @@
-From d06b1043644a1831ab141bbee2669002bba15b0f Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth at gmail.com>
-Date: Wed, 20 Dec 2023 23:17:22 +0100
-Subject: [PATCH] clk: qcom: clk-rcg: introduce support for multiple conf for
- same freq
-
-Some RCG frequency can be reached by multiple configuration.
-
-We currently declare multiple configuration for the same frequency but
-that is not supported and always the first configuration will be taken.
-
-These multiple configuration are needed as based on the current parent
-configuration, it may be needed to use a different configuration to
-reach the same frequency.
-
-To handle this introduce 3 new macro, C, FM and FMS:
-
-- C is used to declare a freq_conf where src, pre_div, m and n are
- provided.
-
-- FM is used to declare a freq_multi_tbl with the frequency and an
- array of confs to insert all the config for the provided frequency.
-
-- FMS is used to declare a freq_multi_tbl with the frequency and an
- array of a single conf with the provided src, pre_div, m and n.
-
-Struct clk_rcg2 is changed to add a union type to reference a simple
-freq_tbl or a complex freq_multi_tbl.
-
-Signed-off-by: Christian Marangi <ansuelsmth at gmail.com>
-Acked-by: Stephen Boyd <sboyd at kernel.org>
-Link: https://lore.kernel.org/r/20231220221724.3822-2-ansuelsmth@gmail.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- drivers/clk/qcom/clk-rcg.h | 23 ++++++++++++++++++++++-
- 1 file changed, 22 insertions(+), 1 deletion(-)
-
---- a/drivers/clk/qcom/clk-rcg.h
-+++ b/drivers/clk/qcom/clk-rcg.h
-@@ -17,6 +17,23 @@ struct freq_tbl {
- u16 n;
- };
-
-+#define C(s, h, m, n) { (s), (2 * (h) - 1), (m), (n) }
-+#define FM(f, confs) { (f), ARRAY_SIZE(confs), (confs) }
-+#define FMS(f, s, h, m, n) { (f), 1, (const struct freq_conf []){ C(s, h, m, n) } }
-+
-+struct freq_conf {
-+ u8 src;
-+ u8 pre_div;
-+ u16 m;
-+ u16 n;
-+};
-+
-+struct freq_multi_tbl {
-+ unsigned long freq;
-+ size_t num_confs;
-+ const struct freq_conf *confs;
-+};
-+
- /**
- * struct mn - M/N:D counter
- * @mnctr_en_bit: bit to enable mn counter
-@@ -138,6 +155,7 @@ extern const struct clk_ops clk_dyn_rcg_
- * @safe_src_index: safe src index value
- * @parent_map: map from software's parent index to hardware's src_sel field
- * @freq_tbl: frequency table
-+ * @freq_multi_tbl: frequency table for clocks reachable with multiple RCGs conf
- * @clkr: regmap clock handle
- * @cfg_off: defines the cfg register offset from the CMD_RCGR + CFG_REG
- * @parked_cfg: cached value of the CFG register for parked RCGs
-@@ -149,7 +167,10 @@ struct clk_rcg2 {
- u8 hid_width;
- u8 safe_src_index;
- const struct parent_map *parent_map;
-- const struct freq_tbl *freq_tbl;
-+ union {
-+ const struct freq_tbl *freq_tbl;
-+ const struct freq_multi_tbl *freq_multi_tbl;
-+ };
- struct clk_regmap clkr;
- u8 cfg_off;
- u32 parked_cfg;
diff --git a/target/linux/qualcommax/patches-6.12/0043-v6.10-clk-qcom-clk-rcg2-add-support-for-rcg2-freq-multi-op.patch b/target/linux/qualcommax/patches-6.12/0043-v6.10-clk-qcom-clk-rcg2-add-support-for-rcg2-freq-multi-op.patch
deleted file mode 100644
index 478f60ed44..0000000000
--- a/target/linux/qualcommax/patches-6.12/0043-v6.10-clk-qcom-clk-rcg2-add-support-for-rcg2-freq-multi-op.patch
+++ /dev/null
@@ -1,296 +0,0 @@
-From 89da22456af0762477d8c1345fdd17961b3ada80 Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth at gmail.com>
-Date: Wed, 20 Dec 2023 23:17:23 +0100
-Subject: [PATCH] clk: qcom: clk-rcg2: add support for rcg2 freq multi ops
-
-Some RCG frequency can be reached by multiple configuration.
-
-Add clk_rcg2_fm_ops ops to support these special RCG configurations.
-
-These alternative ops will select the frequency using a CEIL policy.
-
-When the correct frequency is found, the correct config is selected by
-calculating the final rate (by checking the defined parent and values
-in the config that is being checked) and deciding based on the one that
-is less different than the requested one.
-
-These check are skipped if there is just one config for the requested
-freq.
-
-qcom_find_freq_multi is added to search the freq with the new struct
-freq_multi_tbl.
-__clk_rcg2_select_conf is used to select the correct conf by simulating
-the final clock.
-If a conf can't be found due to parent not reachable, a WARN is printed
-and -EINVAL is returned.
-
-Tested-by: Wei Lei <quic_leiwei at quicinc.com>
-Signed-off-by: Christian Marangi <ansuelsmth at gmail.com>
-Acked-by: Stephen Boyd <sboyd at kernel.org>
-Link: https://lore.kernel.org/r/20231220221724.3822-3-ansuelsmth@gmail.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- drivers/clk/qcom/clk-rcg.h | 1 +
- drivers/clk/qcom/clk-rcg2.c | 166 ++++++++++++++++++++++++++++++++++++
- drivers/clk/qcom/common.c | 18 ++++
- drivers/clk/qcom/common.h | 2 +
- 4 files changed, 187 insertions(+)
-
---- a/drivers/clk/qcom/clk-rcg.h
-+++ b/drivers/clk/qcom/clk-rcg.h
-@@ -190,6 +190,7 @@ struct clk_rcg2_gfx3d {
-
- extern const struct clk_ops clk_rcg2_ops;
- extern const struct clk_ops clk_rcg2_floor_ops;
-+extern const struct clk_ops clk_rcg2_fm_ops;
- extern const struct clk_ops clk_rcg2_mux_closest_ops;
- extern const struct clk_ops clk_edp_pixel_ops;
- extern const struct clk_ops clk_byte_ops;
---- a/drivers/clk/qcom/clk-rcg2.c
-+++ b/drivers/clk/qcom/clk-rcg2.c
-@@ -260,6 +260,115 @@ static int _freq_tbl_determine_rate(stru
- return 0;
- }
-
-+static const struct freq_conf *
-+__clk_rcg2_select_conf(struct clk_hw *hw, const struct freq_multi_tbl *f,
-+ unsigned long req_rate)
-+{
-+ unsigned long rate_diff, best_rate_diff = ULONG_MAX;
-+ const struct freq_conf *conf, *best_conf = NULL;
-+ struct clk_rcg2 *rcg = to_clk_rcg2(hw);
-+ const char *name = clk_hw_get_name(hw);
-+ unsigned long parent_rate, rate;
-+ struct clk_hw *p;
-+ int index, i;
-+
-+ /* Exit early if only one config is defined */
-+ if (f->num_confs == 1) {
-+ best_conf = f->confs;
-+ goto exit;
-+ }
-+
-+ /* Search in each provided config the one that is near the wanted rate */
-+ for (i = 0, conf = f->confs; i < f->num_confs; i++, conf++) {
-+ index = qcom_find_src_index(hw, rcg->parent_map, conf->src);
-+ if (index < 0)
-+ continue;
-+
-+ p = clk_hw_get_parent_by_index(hw, index);
-+ if (!p)
-+ continue;
-+
-+ parent_rate = clk_hw_get_rate(p);
-+ rate = calc_rate(parent_rate, conf->n, conf->m, conf->n, conf->pre_div);
-+
-+ if (rate == req_rate) {
-+ best_conf = conf;
-+ goto exit;
-+ }
-+
-+ rate_diff = abs_diff(req_rate, rate);
-+ if (rate_diff < best_rate_diff) {
-+ best_rate_diff = rate_diff;
-+ best_conf = conf;
-+ }
-+ }
-+
-+ /*
-+ * Very unlikely. Warn if we couldn't find a correct config
-+ * due to parent not found in every config.
-+ */
-+ if (unlikely(!best_conf)) {
-+ WARN(1, "%s: can't find a configuration for rate %lu\n",
-+ name, req_rate);
-+ return ERR_PTR(-EINVAL);
-+ }
-+
-+exit:
-+ return best_conf;
-+}
-+
-+static int _freq_tbl_fm_determine_rate(struct clk_hw *hw, const struct freq_multi_tbl *f,
-+ struct clk_rate_request *req)
-+{
-+ unsigned long clk_flags, rate = req->rate;
-+ struct clk_rcg2 *rcg = to_clk_rcg2(hw);
-+ const struct freq_conf *conf;
-+ struct clk_hw *p;
-+ int index;
-+
-+ f = qcom_find_freq_multi(f, rate);
-+ if (!f || !f->confs)
-+ return -EINVAL;
-+
-+ conf = __clk_rcg2_select_conf(hw, f, rate);
-+ if (IS_ERR(conf))
-+ return PTR_ERR(conf);
-+ index = qcom_find_src_index(hw, rcg->parent_map, conf->src);
-+ if (index < 0)
-+ return index;
-+
-+ clk_flags = clk_hw_get_flags(hw);
-+ p = clk_hw_get_parent_by_index(hw, index);
-+ if (!p)
-+ return -EINVAL;
-+
-+ if (clk_flags & CLK_SET_RATE_PARENT) {
-+ rate = f->freq;
-+ if (conf->pre_div) {
-+ if (!rate)
-+ rate = req->rate;
-+ rate /= 2;
-+ rate *= conf->pre_div + 1;
-+ }
-+
-+ if (conf->n) {
-+ u64 tmp = rate;
-+
-+ tmp = tmp * conf->n;
-+ do_div(tmp, conf->m);
-+ rate = tmp;
-+ }
-+ } else {
-+ rate = clk_hw_get_rate(p);
-+ }
-+
-+ req->best_parent_hw = p;
-+ req->best_parent_rate = rate;
-+ req->rate = f->freq;
-+
-+ return 0;
-+}
-+
- static int clk_rcg2_determine_rate(struct clk_hw *hw,
- struct clk_rate_request *req)
- {
-@@ -276,6 +385,14 @@ static int clk_rcg2_determine_floor_rate
- return _freq_tbl_determine_rate(hw, rcg->freq_tbl, req, FLOOR);
- }
-
-+static int clk_rcg2_fm_determine_rate(struct clk_hw *hw,
-+ struct clk_rate_request *req)
-+{
-+ struct clk_rcg2 *rcg = to_clk_rcg2(hw);
-+
-+ return _freq_tbl_fm_determine_rate(hw, rcg->freq_multi_tbl, req);
-+}
-+
- static int __clk_rcg2_configure(struct clk_rcg2 *rcg, const struct freq_tbl *f,
- u32 *_cfg)
- {
-@@ -371,6 +488,30 @@ static int __clk_rcg2_set_rate(struct cl
- return clk_rcg2_configure(rcg, f);
- }
-
-+static int __clk_rcg2_fm_set_rate(struct clk_hw *hw, unsigned long rate)
-+{
-+ struct clk_rcg2 *rcg = to_clk_rcg2(hw);
-+ const struct freq_multi_tbl *f;
-+ const struct freq_conf *conf;
-+ struct freq_tbl f_tbl = {};
-+
-+ f = qcom_find_freq_multi(rcg->freq_multi_tbl, rate);
-+ if (!f || !f->confs)
-+ return -EINVAL;
-+
-+ conf = __clk_rcg2_select_conf(hw, f, rate);
-+ if (IS_ERR(conf))
-+ return PTR_ERR(conf);
-+
-+ f_tbl.freq = f->freq;
-+ f_tbl.src = conf->src;
-+ f_tbl.pre_div = conf->pre_div;
-+ f_tbl.m = conf->m;
-+ f_tbl.n = conf->n;
-+
-+ return clk_rcg2_configure(rcg, &f_tbl);
-+}
-+
- static int clk_rcg2_set_rate(struct clk_hw *hw, unsigned long rate,
- unsigned long parent_rate)
- {
-@@ -383,6 +524,12 @@ static int clk_rcg2_set_floor_rate(struc
- return __clk_rcg2_set_rate(hw, rate, FLOOR);
- }
-
-+static int clk_rcg2_fm_set_rate(struct clk_hw *hw, unsigned long rate,
-+ unsigned long parent_rate)
-+{
-+ return __clk_rcg2_fm_set_rate(hw, rate);
-+}
-+
- static int clk_rcg2_set_rate_and_parent(struct clk_hw *hw,
- unsigned long rate, unsigned long parent_rate, u8 index)
- {
-@@ -395,6 +542,12 @@ static int clk_rcg2_set_floor_rate_and_p
- return __clk_rcg2_set_rate(hw, rate, FLOOR);
- }
-
-+static int clk_rcg2_fm_set_rate_and_parent(struct clk_hw *hw,
-+ unsigned long rate, unsigned long parent_rate, u8 index)
-+{
-+ return __clk_rcg2_fm_set_rate(hw, rate);
-+}
-+
- static int clk_rcg2_get_duty_cycle(struct clk_hw *hw, struct clk_duty *duty)
- {
- struct clk_rcg2 *rcg = to_clk_rcg2(hw);
-@@ -505,6 +658,19 @@ const struct clk_ops clk_rcg2_floor_ops
- };
- EXPORT_SYMBOL_GPL(clk_rcg2_floor_ops);
-
-+const struct clk_ops clk_rcg2_fm_ops = {
-+ .is_enabled = clk_rcg2_is_enabled,
-+ .get_parent = clk_rcg2_get_parent,
-+ .set_parent = clk_rcg2_set_parent,
-+ .recalc_rate = clk_rcg2_recalc_rate,
-+ .determine_rate = clk_rcg2_fm_determine_rate,
-+ .set_rate = clk_rcg2_fm_set_rate,
-+ .set_rate_and_parent = clk_rcg2_fm_set_rate_and_parent,
-+ .get_duty_cycle = clk_rcg2_get_duty_cycle,
-+ .set_duty_cycle = clk_rcg2_set_duty_cycle,
-+};
-+EXPORT_SYMBOL_GPL(clk_rcg2_fm_ops);
-+
- const struct clk_ops clk_rcg2_mux_closest_ops = {
- .determine_rate = __clk_mux_determine_rate_closest,
- .get_parent = clk_rcg2_get_parent,
---- a/drivers/clk/qcom/common.c
-+++ b/drivers/clk/qcom/common.c
-@@ -41,6 +41,24 @@ struct freq_tbl *qcom_find_freq(const st
- }
- EXPORT_SYMBOL_GPL(qcom_find_freq);
-
-+const struct freq_multi_tbl *qcom_find_freq_multi(const struct freq_multi_tbl *f,
-+ unsigned long rate)
-+{
-+ if (!f)
-+ return NULL;
-+
-+ if (!f->freq)
-+ return f;
-+
-+ for (; f->freq; f++)
-+ if (rate <= f->freq)
-+ return f;
-+
-+ /* Default to our fastest rate */
-+ return f - 1;
-+}
-+EXPORT_SYMBOL_GPL(qcom_find_freq_multi);
-+
- const struct freq_tbl *qcom_find_freq_floor(const struct freq_tbl *f,
- unsigned long rate)
- {
---- a/drivers/clk/qcom/common.h
-+++ b/drivers/clk/qcom/common.h
-@@ -45,6 +45,8 @@ extern const struct freq_tbl *qcom_find_
- unsigned long rate);
- extern const struct freq_tbl *qcom_find_freq_floor(const struct freq_tbl *f,
- unsigned long rate);
-+extern const struct freq_multi_tbl *qcom_find_freq_multi(const struct freq_multi_tbl *f,
-+ unsigned long rate);
- extern void
- qcom_pll_set_fsm_mode(struct regmap *m, u32 reg, u8 bias_count, u8 lock_count);
- extern int qcom_find_src_index(struct clk_hw *hw, const struct parent_map *map,
diff --git a/target/linux/qualcommax/patches-6.12/0044-v6.10-clk-qcom-gcc-ipq8074-rework-nss_port5-6-clock-to-mul.patch b/target/linux/qualcommax/patches-6.12/0044-v6.10-clk-qcom-gcc-ipq8074-rework-nss_port5-6-clock-to-mul.patch
deleted file mode 100644
index 5360771df2..0000000000
--- a/target/linux/qualcommax/patches-6.12/0044-v6.10-clk-qcom-gcc-ipq8074-rework-nss_port5-6-clock-to-mul.patch
+++ /dev/null
@@ -1,227 +0,0 @@
-From e88f03230dc07aa3293b6aeb078bd27370bb2594 Mon Sep 17 00:00:00 2001
-From: Christian Marangi <ansuelsmth at gmail.com>
-Date: Wed, 20 Dec 2023 23:17:24 +0100
-Subject: [PATCH] clk: qcom: gcc-ipq8074: rework nss_port5/6 clock to multiple
- conf
-
-Rework nss_port5/6 to use the new multiple configuration implementation
-and correctly fix the clocks for these port under some corner case.
-
-This is particularly relevant for device that have 2.5G or 10G port
-connected to port5 or port 6 on ipq8074. As the parent are shared
-across multiple port it may be required to select the correct
-configuration to accomplish the desired clock. Without this patch such
-port doesn't work in some specific ethernet speed as the clock will be
-set to the wrong frequency as we just select the first configuration for
-the related frequency instead of selecting the best one.
-
-Signed-off-by: Christian Marangi <ansuelsmth at gmail.com>
-Acked-by: Stephen Boyd <sboyd at kernel.org>
-Link: https://lore.kernel.org/r/20231220221724.3822-4-ansuelsmth@gmail.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- drivers/clk/qcom/gcc-ipq8074.c | 120 +++++++++++++++++++++------------
- 1 file changed, 76 insertions(+), 44 deletions(-)
-
---- a/drivers/clk/qcom/gcc-ipq8074.c
-+++ b/drivers/clk/qcom/gcc-ipq8074.c
-@@ -1677,15 +1677,23 @@ static struct clk_regmap_div nss_port4_t
- },
- };
-
--static const struct freq_tbl ftbl_nss_port5_rx_clk_src[] = {
-- F(19200000, P_XO, 1, 0, 0),
-- F(25000000, P_UNIPHY1_RX, 12.5, 0, 0),
-- F(25000000, P_UNIPHY0_RX, 5, 0, 0),
-- F(78125000, P_UNIPHY1_RX, 4, 0, 0),
-- F(125000000, P_UNIPHY1_RX, 2.5, 0, 0),
-- F(125000000, P_UNIPHY0_RX, 1, 0, 0),
-- F(156250000, P_UNIPHY1_RX, 2, 0, 0),
-- F(312500000, P_UNIPHY1_RX, 1, 0, 0),
-+static const struct freq_conf ftbl_nss_port5_rx_clk_src_25[] = {
-+ C(P_UNIPHY1_RX, 12.5, 0, 0),
-+ C(P_UNIPHY0_RX, 5, 0, 0),
-+};
-+
-+static const struct freq_conf ftbl_nss_port5_rx_clk_src_125[] = {
-+ C(P_UNIPHY1_RX, 2.5, 0, 0),
-+ C(P_UNIPHY0_RX, 1, 0, 0),
-+};
-+
-+static const struct freq_multi_tbl ftbl_nss_port5_rx_clk_src[] = {
-+ FMS(19200000, P_XO, 1, 0, 0),
-+ FM(25000000, ftbl_nss_port5_rx_clk_src_25),
-+ FMS(78125000, P_UNIPHY1_RX, 4, 0, 0),
-+ FM(125000000, ftbl_nss_port5_rx_clk_src_125),
-+ FMS(156250000, P_UNIPHY1_RX, 2, 0, 0),
-+ FMS(312500000, P_UNIPHY1_RX, 1, 0, 0),
- { }
- };
-
-@@ -1712,14 +1720,14 @@ gcc_xo_uniphy0_rx_tx_uniphy1_rx_tx_ubi32
-
- static struct clk_rcg2 nss_port5_rx_clk_src = {
- .cmd_rcgr = 0x68060,
-- .freq_tbl = ftbl_nss_port5_rx_clk_src,
-+ .freq_multi_tbl = ftbl_nss_port5_rx_clk_src,
- .hid_width = 5,
- .parent_map = gcc_xo_uniphy0_rx_tx_uniphy1_rx_tx_ubi32_bias_map,
- .clkr.hw.init = &(struct clk_init_data){
- .name = "nss_port5_rx_clk_src",
- .parent_data = gcc_xo_uniphy0_rx_tx_uniphy1_rx_tx_ubi32_bias,
- .num_parents = ARRAY_SIZE(gcc_xo_uniphy0_rx_tx_uniphy1_rx_tx_ubi32_bias),
-- .ops = &clk_rcg2_ops,
-+ .ops = &clk_rcg2_fm_ops,
- },
- };
-
-@@ -1739,15 +1747,23 @@ static struct clk_regmap_div nss_port5_r
- },
- };
-
--static const struct freq_tbl ftbl_nss_port5_tx_clk_src[] = {
-- F(19200000, P_XO, 1, 0, 0),
-- F(25000000, P_UNIPHY1_TX, 12.5, 0, 0),
-- F(25000000, P_UNIPHY0_TX, 5, 0, 0),
-- F(78125000, P_UNIPHY1_TX, 4, 0, 0),
-- F(125000000, P_UNIPHY1_TX, 2.5, 0, 0),
-- F(125000000, P_UNIPHY0_TX, 1, 0, 0),
-- F(156250000, P_UNIPHY1_TX, 2, 0, 0),
-- F(312500000, P_UNIPHY1_TX, 1, 0, 0),
-+static const struct freq_conf ftbl_nss_port5_tx_clk_src_25[] = {
-+ C(P_UNIPHY1_TX, 12.5, 0, 0),
-+ C(P_UNIPHY0_TX, 5, 0, 0),
-+};
-+
-+static const struct freq_conf ftbl_nss_port5_tx_clk_src_125[] = {
-+ C(P_UNIPHY1_TX, 2.5, 0, 0),
-+ C(P_UNIPHY0_TX, 1, 0, 0),
-+};
-+
-+static const struct freq_multi_tbl ftbl_nss_port5_tx_clk_src[] = {
-+ FMS(19200000, P_XO, 1, 0, 0),
-+ FM(25000000, ftbl_nss_port5_tx_clk_src_25),
-+ FMS(78125000, P_UNIPHY1_TX, 4, 0, 0),
-+ FM(125000000, ftbl_nss_port5_tx_clk_src_125),
-+ FMS(156250000, P_UNIPHY1_TX, 2, 0, 0),
-+ FMS(312500000, P_UNIPHY1_TX, 1, 0, 0),
- { }
- };
-
-@@ -1774,14 +1790,14 @@ gcc_xo_uniphy0_tx_rx_uniphy1_tx_rx_ubi32
-
- static struct clk_rcg2 nss_port5_tx_clk_src = {
- .cmd_rcgr = 0x68068,
-- .freq_tbl = ftbl_nss_port5_tx_clk_src,
-+ .freq_multi_tbl = ftbl_nss_port5_tx_clk_src,
- .hid_width = 5,
- .parent_map = gcc_xo_uniphy0_tx_rx_uniphy1_tx_rx_ubi32_bias_map,
- .clkr.hw.init = &(struct clk_init_data){
- .name = "nss_port5_tx_clk_src",
- .parent_data = gcc_xo_uniphy0_tx_rx_uniphy1_tx_rx_ubi32_bias,
- .num_parents = ARRAY_SIZE(gcc_xo_uniphy0_tx_rx_uniphy1_tx_rx_ubi32_bias),
-- .ops = &clk_rcg2_ops,
-+ .ops = &clk_rcg2_fm_ops,
- },
- };
-
-@@ -1801,15 +1817,23 @@ static struct clk_regmap_div nss_port5_t
- },
- };
-
--static const struct freq_tbl ftbl_nss_port6_rx_clk_src[] = {
-- F(19200000, P_XO, 1, 0, 0),
-- F(25000000, P_UNIPHY2_RX, 5, 0, 0),
-- F(25000000, P_UNIPHY2_RX, 12.5, 0, 0),
-- F(78125000, P_UNIPHY2_RX, 4, 0, 0),
-- F(125000000, P_UNIPHY2_RX, 1, 0, 0),
-- F(125000000, P_UNIPHY2_RX, 2.5, 0, 0),
-- F(156250000, P_UNIPHY2_RX, 2, 0, 0),
-- F(312500000, P_UNIPHY2_RX, 1, 0, 0),
-+static const struct freq_conf ftbl_nss_port6_rx_clk_src_25[] = {
-+ C(P_UNIPHY2_RX, 5, 0, 0),
-+ C(P_UNIPHY2_RX, 12.5, 0, 0),
-+};
-+
-+static const struct freq_conf ftbl_nss_port6_rx_clk_src_125[] = {
-+ C(P_UNIPHY2_RX, 1, 0, 0),
-+ C(P_UNIPHY2_RX, 2.5, 0, 0),
-+};
-+
-+static const struct freq_multi_tbl ftbl_nss_port6_rx_clk_src[] = {
-+ FMS(19200000, P_XO, 1, 0, 0),
-+ FM(25000000, ftbl_nss_port6_rx_clk_src_25),
-+ FMS(78125000, P_UNIPHY2_RX, 4, 0, 0),
-+ FM(125000000, ftbl_nss_port6_rx_clk_src_125),
-+ FMS(156250000, P_UNIPHY2_RX, 2, 0, 0),
-+ FMS(312500000, P_UNIPHY2_RX, 1, 0, 0),
- { }
- };
-
-@@ -1831,14 +1855,14 @@ static const struct parent_map gcc_xo_un
-
- static struct clk_rcg2 nss_port6_rx_clk_src = {
- .cmd_rcgr = 0x68070,
-- .freq_tbl = ftbl_nss_port6_rx_clk_src,
-+ .freq_multi_tbl = ftbl_nss_port6_rx_clk_src,
- .hid_width = 5,
- .parent_map = gcc_xo_uniphy2_rx_tx_ubi32_bias_map,
- .clkr.hw.init = &(struct clk_init_data){
- .name = "nss_port6_rx_clk_src",
- .parent_data = gcc_xo_uniphy2_rx_tx_ubi32_bias,
- .num_parents = ARRAY_SIZE(gcc_xo_uniphy2_rx_tx_ubi32_bias),
-- .ops = &clk_rcg2_ops,
-+ .ops = &clk_rcg2_fm_ops,
- },
- };
-
-@@ -1858,15 +1882,23 @@ static struct clk_regmap_div nss_port6_r
- },
- };
-
--static const struct freq_tbl ftbl_nss_port6_tx_clk_src[] = {
-- F(19200000, P_XO, 1, 0, 0),
-- F(25000000, P_UNIPHY2_TX, 5, 0, 0),
-- F(25000000, P_UNIPHY2_TX, 12.5, 0, 0),
-- F(78125000, P_UNIPHY2_TX, 4, 0, 0),
-- F(125000000, P_UNIPHY2_TX, 1, 0, 0),
-- F(125000000, P_UNIPHY2_TX, 2.5, 0, 0),
-- F(156250000, P_UNIPHY2_TX, 2, 0, 0),
-- F(312500000, P_UNIPHY2_TX, 1, 0, 0),
-+static const struct freq_conf ftbl_nss_port6_tx_clk_src_25[] = {
-+ C(P_UNIPHY2_TX, 5, 0, 0),
-+ C(P_UNIPHY2_TX, 12.5, 0, 0),
-+};
-+
-+static const struct freq_conf ftbl_nss_port6_tx_clk_src_125[] = {
-+ C(P_UNIPHY2_TX, 1, 0, 0),
-+ C(P_UNIPHY2_TX, 2.5, 0, 0),
-+};
-+
-+static const struct freq_multi_tbl ftbl_nss_port6_tx_clk_src[] = {
-+ FMS(19200000, P_XO, 1, 0, 0),
-+ FM(25000000, ftbl_nss_port6_tx_clk_src_25),
-+ FMS(78125000, P_UNIPHY1_RX, 4, 0, 0),
-+ FM(125000000, ftbl_nss_port6_tx_clk_src_125),
-+ FMS(156250000, P_UNIPHY1_RX, 2, 0, 0),
-+ FMS(312500000, P_UNIPHY1_RX, 1, 0, 0),
- { }
- };
-
-@@ -1888,14 +1920,14 @@ static const struct parent_map gcc_xo_un
-
- static struct clk_rcg2 nss_port6_tx_clk_src = {
- .cmd_rcgr = 0x68078,
-- .freq_tbl = ftbl_nss_port6_tx_clk_src,
-+ .freq_multi_tbl = ftbl_nss_port6_tx_clk_src,
- .hid_width = 5,
- .parent_map = gcc_xo_uniphy2_tx_rx_ubi32_bias_map,
- .clkr.hw.init = &(struct clk_init_data){
- .name = "nss_port6_tx_clk_src",
- .parent_data = gcc_xo_uniphy2_tx_rx_ubi32_bias,
- .num_parents = ARRAY_SIZE(gcc_xo_uniphy2_tx_rx_ubi32_bias),
-- .ops = &clk_rcg2_ops,
-+ .ops = &clk_rcg2_fm_ops,
- },
- };
-
diff --git a/target/linux/qualcommax/patches-6.12/0045-v6.7-arm64-dts-qcom-ipq8074-switch-PCIe-QMP-PHY-to-new-st.patch b/target/linux/qualcommax/patches-6.12/0045-v6.7-arm64-dts-qcom-ipq8074-switch-PCIe-QMP-PHY-to-new-st.patch
deleted file mode 100644
index b85d073b9d..0000000000
--- a/target/linux/qualcommax/patches-6.12/0045-v6.7-arm64-dts-qcom-ipq8074-switch-PCIe-QMP-PHY-to-new-st.patch
+++ /dev/null
@@ -1,122 +0,0 @@
-From 9e5e778f3340a687dd91c533064f963d352921c6 Mon Sep 17 00:00:00 2001
-From: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
-Date: Sun, 20 Aug 2023 17:20:26 +0300
-Subject: [PATCH] arm64: dts: qcom: ipq8074: switch PCIe QMP PHY to new style
- of bindings
-
-Change the PCIe QMP PHY to use newer style of QMP PHY bindings (single
-resource region, no per-PHY subnodes).
-
-Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
-Link: https://lore.kernel.org/r/20230820142035.89903-10-dmitry.baryshkov@linaro.org
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- arch/arm64/boot/dts/qcom/ipq8074.dtsi | 67 +++++++++++----------------
- 1 file changed, 28 insertions(+), 39 deletions(-)
-
---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
-+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
-@@ -211,59 +211,48 @@
-
- pcie_qmp0: phy at 84000 {
- compatible = "qcom,ipq8074-qmp-gen3-pcie-phy";
-- reg = <0x00084000 0x1bc>;
-- #address-cells = <1>;
-- #size-cells = <1>;
-- ranges;
-+ reg = <0x00084000 0x1000>;
-
- clocks = <&gcc GCC_PCIE0_AUX_CLK>,
-- <&gcc GCC_PCIE0_AHB_CLK>;
-- clock-names = "aux", "cfg_ahb";
-+ <&gcc GCC_PCIE0_AHB_CLK>,
-+ <&gcc GCC_PCIE0_PIPE_CLK>;
-+ clock-names = "aux",
-+ "cfg_ahb",
-+ "pipe";
-+
-+ clock-output-names = "pcie20_phy0_pipe_clk";
-+ #clock-cells = <0>;
-+
-+ #phy-cells = <0>;
-+
- resets = <&gcc GCC_PCIE0_PHY_BCR>,
-- <&gcc GCC_PCIE0PHY_PHY_BCR>;
-+ <&gcc GCC_PCIE0PHY_PHY_BCR>;
- reset-names = "phy",
- "common";
- status = "disabled";
--
-- pcie_phy0: phy at 84200 {
-- reg = <0x84200 0x16c>,
-- <0x84400 0x200>,
-- <0x84800 0x1f0>,
-- <0x84c00 0xf4>;
-- #phy-cells = <0>;
-- #clock-cells = <0>;
-- clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
-- clock-names = "pipe0";
-- clock-output-names = "pcie20_phy0_pipe_clk";
-- };
- };
-
- pcie_qmp1: phy at 8e000 {
- compatible = "qcom,ipq8074-qmp-pcie-phy";
-- reg = <0x0008e000 0x1c4>;
-- #address-cells = <1>;
-- #size-cells = <1>;
-- ranges;
-+ reg = <0x0008e000 0x1000>;
-
- clocks = <&gcc GCC_PCIE1_AUX_CLK>,
-- <&gcc GCC_PCIE1_AHB_CLK>;
-- clock-names = "aux", "cfg_ahb";
-+ <&gcc GCC_PCIE1_AHB_CLK>,
-+ <&gcc GCC_PCIE1_PIPE_CLK>;
-+ clock-names = "aux",
-+ "cfg_ahb",
-+ "pipe";
-+
-+ clock-output-names = "pcie20_phy1_pipe_clk";
-+ #clock-cells = <0>;
-+
-+ #phy-cells = <0>;
-+
- resets = <&gcc GCC_PCIE1_PHY_BCR>,
-- <&gcc GCC_PCIE1PHY_PHY_BCR>;
-+ <&gcc GCC_PCIE1PHY_PHY_BCR>;
- reset-names = "phy",
- "common";
- status = "disabled";
--
-- pcie_phy1: phy at 8e200 {
-- reg = <0x8e200 0x130>,
-- <0x8e400 0x200>,
-- <0x8e800 0x1f8>;
-- #phy-cells = <0>;
-- #clock-cells = <0>;
-- clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
-- clock-names = "pipe0";
-- clock-output-names = "pcie20_phy1_pipe_clk";
-- };
- };
-
- mdio: mdio at 90000 {
-@@ -839,7 +828,7 @@
- #address-cells = <3>;
- #size-cells = <2>;
-
-- phys = <&pcie_phy1>;
-+ phys = <&pcie_qmp1>;
- phy-names = "pciephy";
-
- ranges = <0x81000000 0x0 0x00000000 0x10200000 0x0 0x10000>, /* I/O */
-@@ -901,7 +890,7 @@
- #address-cells = <3>;
- #size-cells = <2>;
-
-- phys = <&pcie_phy0>;
-+ phys = <&pcie_qmp0>;
- phy-names = "pciephy";
-
- ranges = <0x81000000 0x0 0x00000000 0x20200000 0x0 0x10000>, /* I/O */
diff --git a/target/linux/qualcommax/patches-6.12/0046-v6.8-arm64-dts-qcom-ipq8074-pass-QMP-PCI-PHY-PIPE-clocks-.patch b/target/linux/qualcommax/patches-6.12/0046-v6.8-arm64-dts-qcom-ipq8074-pass-QMP-PCI-PHY-PIPE-clocks-.patch
deleted file mode 100644
index e1bdf01ded..0000000000
--- a/target/linux/qualcommax/patches-6.12/0046-v6.8-arm64-dts-qcom-ipq8074-pass-QMP-PCI-PHY-PIPE-clocks-.patch
+++ /dev/null
@@ -1,39 +0,0 @@
-From 591da388c344f934601548cb44f54eab012c6c94 Mon Sep 17 00:00:00 2001
-From: Robert Marko <robimarko at gmail.com>
-Date: Fri, 13 Oct 2023 18:39:34 +0200
-Subject: [PATCH] arm64: dts: qcom: ipq8074: pass QMP PCI PHY PIPE clocks to
- GCC
-
-Pass QMP PCI PHY PIPE clocks to the GCC controller so it does not have to
-find them by matching globaly by name.
-
-If not passed directly, driver maintains backwards compatibility by then
-falling back to global lookup.
-
-Signed-off-by: Robert Marko <robimarko at gmail.com>
-Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov at linaro.org>
-Link: https://lore.kernel.org/r/20231013164025.3541606-2-robimarko@gmail.com
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- arch/arm64/boot/dts/qcom/ipq8074.dtsi | 10 ++++++++--
- 1 file changed, 8 insertions(+), 2 deletions(-)
-
---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
-+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
-@@ -371,8 +371,14 @@
- gcc: gcc at 1800000 {
- compatible = "qcom,gcc-ipq8074";
- reg = <0x01800000 0x80000>;
-- clocks = <&xo>, <&sleep_clk>;
-- clock-names = "xo", "sleep_clk";
-+ clocks = <&xo>,
-+ <&sleep_clk>,
-+ <&pcie_qmp0>,
-+ <&pcie_qmp1>;
-+ clock-names = "xo",
-+ "sleep_clk",
-+ "pcie0_pipe",
-+ "pcie1_pipe";
- #clock-cells = <1>;
- #power-domain-cells = <1>;
- #reset-cells = <1>;
diff --git a/target/linux/qualcommax/patches-6.12/0047-v6.11-PCI-qcom-Use-devm_clk_bulk_get_all-API.patch b/target/linux/qualcommax/patches-6.12/0047-v6.11-PCI-qcom-Use-devm_clk_bulk_get_all-API.patch
deleted file mode 100644
index 453620f320..0000000000
--- a/target/linux/qualcommax/patches-6.12/0047-v6.11-PCI-qcom-Use-devm_clk_bulk_get_all-API.patch
+++ /dev/null
@@ -1,388 +0,0 @@
-From 652935ba05860eadaa19ac9efe7aea61fb7a3aef Mon Sep 17 00:00:00 2001
-From: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
-Date: Wed, 17 Apr 2024 12:32:53 +0530
-Subject: [PATCH] PCI: qcom: Use devm_clk_bulk_get_all() API
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-There is no need for the device drivers to validate the clocks defined in
-Devicetree. The validation should be performed by the DT schema and the
-drivers should just get all the clocks from DT. Right now the driver
-hardcodes the clock info and validates them against DT which is redundant.
-
-So use devm_clk_bulk_get_all() that just gets all the clocks defined in DT
-and get rid of all static clocks info from the driver. This simplifies the
-driver.
-
-Link: https://lore.kernel.org/linux-pci/20240417-pci-qcom-clk-bulk-v1-1-52ca19b3d6b2@linaro.org
-Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
-Signed-off-by: Krzysztof Wilczyński <kwilczynski at kernel.org>
-Signed-off-by: Bjorn Helgaas <bhelgaas at google.com>
----
- drivers/pci/controller/dwc/pcie-qcom.c | 177 ++++++++-----------------
- 1 file changed, 58 insertions(+), 119 deletions(-)
-
---- a/drivers/pci/controller/dwc/pcie-qcom.c
-+++ b/drivers/pci/controller/dwc/pcie-qcom.c
-@@ -151,58 +151,56 @@
-
- #define QCOM_PCIE_CRC8_POLYNOMIAL (BIT(2) | BIT(1) | BIT(0))
-
--#define QCOM_PCIE_1_0_0_MAX_CLOCKS 4
- struct qcom_pcie_resources_1_0_0 {
-- struct clk_bulk_data clks[QCOM_PCIE_1_0_0_MAX_CLOCKS];
-+ struct clk_bulk_data *clks;
-+ int num_clks;
- struct reset_control *core;
- struct regulator *vdda;
- };
-
--#define QCOM_PCIE_2_1_0_MAX_CLOCKS 5
- #define QCOM_PCIE_2_1_0_MAX_RESETS 6
- #define QCOM_PCIE_2_1_0_MAX_SUPPLY 3
- struct qcom_pcie_resources_2_1_0 {
-- struct clk_bulk_data clks[QCOM_PCIE_2_1_0_MAX_CLOCKS];
-+ struct clk_bulk_data *clks;
-+ int num_clks;
- struct reset_control_bulk_data resets[QCOM_PCIE_2_1_0_MAX_RESETS];
- int num_resets;
- struct regulator_bulk_data supplies[QCOM_PCIE_2_1_0_MAX_SUPPLY];
- };
-
--#define QCOM_PCIE_2_3_2_MAX_CLOCKS 4
- #define QCOM_PCIE_2_3_2_MAX_SUPPLY 2
- struct qcom_pcie_resources_2_3_2 {
-- struct clk_bulk_data clks[QCOM_PCIE_2_3_2_MAX_CLOCKS];
-+ struct clk_bulk_data *clks;
-+ int num_clks;
- struct regulator_bulk_data supplies[QCOM_PCIE_2_3_2_MAX_SUPPLY];
- };
-
--#define QCOM_PCIE_2_3_3_MAX_CLOCKS 5
- #define QCOM_PCIE_2_3_3_MAX_RESETS 7
- struct qcom_pcie_resources_2_3_3 {
-- struct clk_bulk_data clks[QCOM_PCIE_2_3_3_MAX_CLOCKS];
-+ struct clk_bulk_data *clks;
-+ int num_clks;
- struct reset_control_bulk_data rst[QCOM_PCIE_2_3_3_MAX_RESETS];
- };
-
--#define QCOM_PCIE_2_4_0_MAX_CLOCKS 4
- #define QCOM_PCIE_2_4_0_MAX_RESETS 12
- struct qcom_pcie_resources_2_4_0 {
-- struct clk_bulk_data clks[QCOM_PCIE_2_4_0_MAX_CLOCKS];
-+ struct clk_bulk_data *clks;
- int num_clks;
- struct reset_control_bulk_data resets[QCOM_PCIE_2_4_0_MAX_RESETS];
- int num_resets;
- };
-
--#define QCOM_PCIE_2_7_0_MAX_CLOCKS 15
- #define QCOM_PCIE_2_7_0_MAX_SUPPLIES 2
- struct qcom_pcie_resources_2_7_0 {
-- struct clk_bulk_data clks[QCOM_PCIE_2_7_0_MAX_CLOCKS];
-+ struct clk_bulk_data *clks;
- int num_clks;
- struct regulator_bulk_data supplies[QCOM_PCIE_2_7_0_MAX_SUPPLIES];
- struct reset_control *rst;
- };
-
--#define QCOM_PCIE_2_9_0_MAX_CLOCKS 5
- struct qcom_pcie_resources_2_9_0 {
-- struct clk_bulk_data clks[QCOM_PCIE_2_9_0_MAX_CLOCKS];
-+ struct clk_bulk_data *clks;
-+ int num_clks;
- struct reset_control *rst;
- };
-
-@@ -313,21 +311,11 @@ static int qcom_pcie_get_resources_2_1_0
- if (ret)
- return ret;
-
-- res->clks[0].id = "iface";
-- res->clks[1].id = "core";
-- res->clks[2].id = "phy";
-- res->clks[3].id = "aux";
-- res->clks[4].id = "ref";
--
-- /* iface, core, phy are required */
-- ret = devm_clk_bulk_get(dev, 3, res->clks);
-- if (ret < 0)
-- return ret;
--
-- /* aux, ref are optional */
-- ret = devm_clk_bulk_get_optional(dev, 2, res->clks + 3);
-- if (ret < 0)
-- return ret;
-+ res->num_clks = devm_clk_bulk_get_all(dev, &res->clks);
-+ if (res->num_clks < 0) {
-+ dev_err(dev, "Failed to get clocks\n");
-+ return res->num_clks;
-+ }
-
- res->resets[0].id = "pci";
- res->resets[1].id = "axi";
-@@ -349,7 +337,7 @@ static void qcom_pcie_deinit_2_1_0(struc
- {
- struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0;
-
-- clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
-+ clk_bulk_disable_unprepare(res->num_clks, res->clks);
- reset_control_bulk_assert(res->num_resets, res->resets);
-
- writel(1, pcie->parf + PARF_PHY_CTRL);
-@@ -401,7 +389,7 @@ static int qcom_pcie_post_init_2_1_0(str
- val &= ~PHY_TEST_PWR_DOWN;
- writel(val, pcie->parf + PARF_PHY_CTRL);
-
-- ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
-+ ret = clk_bulk_prepare_enable(res->num_clks, res->clks);
- if (ret)
- return ret;
-
-@@ -452,20 +440,16 @@ static int qcom_pcie_get_resources_1_0_0
- struct qcom_pcie_resources_1_0_0 *res = &pcie->res.v1_0_0;
- struct dw_pcie *pci = pcie->pci;
- struct device *dev = pci->dev;
-- int ret;
-
- res->vdda = devm_regulator_get(dev, "vdda");
- if (IS_ERR(res->vdda))
- return PTR_ERR(res->vdda);
-
-- res->clks[0].id = "iface";
-- res->clks[1].id = "aux";
-- res->clks[2].id = "master_bus";
-- res->clks[3].id = "slave_bus";
--
-- ret = devm_clk_bulk_get(dev, ARRAY_SIZE(res->clks), res->clks);
-- if (ret < 0)
-- return ret;
-+ res->num_clks = devm_clk_bulk_get_all(dev, &res->clks);
-+ if (res->num_clks < 0) {
-+ dev_err(dev, "Failed to get clocks\n");
-+ return res->num_clks;
-+ }
-
- res->core = devm_reset_control_get_exclusive(dev, "core");
- return PTR_ERR_OR_ZERO(res->core);
-@@ -476,7 +460,7 @@ static void qcom_pcie_deinit_1_0_0(struc
- struct qcom_pcie_resources_1_0_0 *res = &pcie->res.v1_0_0;
-
- reset_control_assert(res->core);
-- clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
-+ clk_bulk_disable_unprepare(res->num_clks, res->clks);
- regulator_disable(res->vdda);
- }
-
-@@ -493,7 +477,7 @@ static int qcom_pcie_init_1_0_0(struct q
- return ret;
- }
-
-- ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
-+ ret = clk_bulk_prepare_enable(res->num_clks, res->clks);
- if (ret) {
- dev_err(dev, "cannot prepare/enable clocks\n");
- goto err_assert_reset;
-@@ -508,7 +492,7 @@ static int qcom_pcie_init_1_0_0(struct q
- return 0;
-
- err_disable_clks:
-- clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
-+ clk_bulk_disable_unprepare(res->num_clks, res->clks);
- err_assert_reset:
- reset_control_assert(res->core);
-
-@@ -556,14 +540,11 @@ static int qcom_pcie_get_resources_2_3_2
- if (ret)
- return ret;
-
-- res->clks[0].id = "aux";
-- res->clks[1].id = "cfg";
-- res->clks[2].id = "bus_master";
-- res->clks[3].id = "bus_slave";
--
-- ret = devm_clk_bulk_get(dev, ARRAY_SIZE(res->clks), res->clks);
-- if (ret < 0)
-- return ret;
-+ res->num_clks = devm_clk_bulk_get_all(dev, &res->clks);
-+ if (res->num_clks < 0) {
-+ dev_err(dev, "Failed to get clocks\n");
-+ return res->num_clks;
-+ }
-
- return 0;
- }
-@@ -572,7 +553,7 @@ static void qcom_pcie_deinit_2_3_2(struc
- {
- struct qcom_pcie_resources_2_3_2 *res = &pcie->res.v2_3_2;
-
-- clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
-+ clk_bulk_disable_unprepare(res->num_clks, res->clks);
- regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies);
- }
-
-@@ -589,7 +570,7 @@ static int qcom_pcie_init_2_3_2(struct q
- return ret;
- }
-
-- ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
-+ ret = clk_bulk_prepare_enable(res->num_clks, res->clks);
- if (ret) {
- dev_err(dev, "cannot prepare/enable clocks\n");
- regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies);
-@@ -637,17 +618,11 @@ static int qcom_pcie_get_resources_2_4_0
- bool is_ipq = of_device_is_compatible(dev->of_node, "qcom,pcie-ipq4019");
- int ret;
-
-- res->clks[0].id = "aux";
-- res->clks[1].id = "master_bus";
-- res->clks[2].id = "slave_bus";
-- res->clks[3].id = "iface";
--
-- /* qcom,pcie-ipq4019 is defined without "iface" */
-- res->num_clks = is_ipq ? 3 : 4;
--
-- ret = devm_clk_bulk_get(dev, res->num_clks, res->clks);
-- if (ret < 0)
-- return ret;
-+ res->num_clks = devm_clk_bulk_get_all(dev, &res->clks);
-+ if (res->num_clks < 0) {
-+ dev_err(dev, "Failed to get clocks\n");
-+ return res->num_clks;
-+ }
-
- res->resets[0].id = "axi_m";
- res->resets[1].id = "axi_s";
-@@ -718,15 +693,11 @@ static int qcom_pcie_get_resources_2_3_3
- struct device *dev = pci->dev;
- int ret;
-
-- res->clks[0].id = "iface";
-- res->clks[1].id = "axi_m";
-- res->clks[2].id = "axi_s";
-- res->clks[3].id = "ahb";
-- res->clks[4].id = "aux";
--
-- ret = devm_clk_bulk_get(dev, ARRAY_SIZE(res->clks), res->clks);
-- if (ret < 0)
-- return ret;
-+ res->num_clks = devm_clk_bulk_get_all(dev, &res->clks);
-+ if (res->num_clks < 0) {
-+ dev_err(dev, "Failed to get clocks\n");
-+ return res->num_clks;
-+ }
-
- res->rst[0].id = "axi_m";
- res->rst[1].id = "axi_s";
-@@ -747,7 +718,7 @@ static void qcom_pcie_deinit_2_3_3(struc
- {
- struct qcom_pcie_resources_2_3_3 *res = &pcie->res.v2_3_3;
-
-- clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
-+ clk_bulk_disable_unprepare(res->num_clks, res->clks);
- }
-
- static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie)
-@@ -777,7 +748,7 @@ static int qcom_pcie_init_2_3_3(struct q
- */
- usleep_range(2000, 2500);
-
-- ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
-+ ret = clk_bulk_prepare_enable(res->num_clks, res->clks);
- if (ret) {
- dev_err(dev, "cannot prepare/enable clocks\n");
- goto err_assert_resets;
-@@ -838,8 +809,6 @@ static int qcom_pcie_get_resources_2_7_0
- struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0;
- struct dw_pcie *pci = pcie->pci;
- struct device *dev = pci->dev;
-- unsigned int num_clks, num_opt_clks;
-- unsigned int idx;
- int ret;
-
- res->rst = devm_reset_control_array_get_exclusive(dev);
-@@ -853,36 +822,11 @@ static int qcom_pcie_get_resources_2_7_0
- if (ret)
- return ret;
-
-- idx = 0;
-- res->clks[idx++].id = "aux";
-- res->clks[idx++].id = "cfg";
-- res->clks[idx++].id = "bus_master";
-- res->clks[idx++].id = "bus_slave";
-- res->clks[idx++].id = "slave_q2a";
--
-- num_clks = idx;
--
-- ret = devm_clk_bulk_get(dev, num_clks, res->clks);
-- if (ret < 0)
-- return ret;
--
-- res->clks[idx++].id = "tbu";
-- res->clks[idx++].id = "ddrss_sf_tbu";
-- res->clks[idx++].id = "aggre0";
-- res->clks[idx++].id = "aggre1";
-- res->clks[idx++].id = "noc_aggr";
-- res->clks[idx++].id = "noc_aggr_4";
-- res->clks[idx++].id = "noc_aggr_south_sf";
-- res->clks[idx++].id = "cnoc_qx";
-- res->clks[idx++].id = "sleep";
-- res->clks[idx++].id = "cnoc_sf_axi";
--
-- num_opt_clks = idx - num_clks;
-- res->num_clks = idx;
--
-- ret = devm_clk_bulk_get_optional(dev, num_opt_clks, res->clks + num_clks);
-- if (ret < 0)
-- return ret;
-+ res->num_clks = devm_clk_bulk_get_all(dev, &res->clks);
-+ if (res->num_clks < 0) {
-+ dev_err(dev, "Failed to get clocks\n");
-+ return res->num_clks;
-+ }
-
- return 0;
- }
-@@ -1073,17 +1017,12 @@ static int qcom_pcie_get_resources_2_9_0
- struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
- struct dw_pcie *pci = pcie->pci;
- struct device *dev = pci->dev;
-- int ret;
--
-- res->clks[0].id = "iface";
-- res->clks[1].id = "axi_m";
-- res->clks[2].id = "axi_s";
-- res->clks[3].id = "axi_bridge";
-- res->clks[4].id = "rchng";
-
-- ret = devm_clk_bulk_get(dev, ARRAY_SIZE(res->clks), res->clks);
-- if (ret < 0)
-- return ret;
-+ res->num_clks = devm_clk_bulk_get_all(dev, &res->clks);
-+ if (res->num_clks < 0) {
-+ dev_err(dev, "Failed to get clocks\n");
-+ return res->num_clks;
-+ }
-
- res->rst = devm_reset_control_array_get_exclusive(dev);
- if (IS_ERR(res->rst))
-@@ -1096,7 +1035,7 @@ static void qcom_pcie_deinit_2_9_0(struc
- {
- struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
-
-- clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);
-+ clk_bulk_disable_unprepare(res->num_clks, res->clks);
- }
-
- static int qcom_pcie_init_2_9_0(struct qcom_pcie *pcie)
-@@ -1125,7 +1064,7 @@ static int qcom_pcie_init_2_9_0(struct q
-
- usleep_range(2000, 2500);
-
-- return clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
-+ return clk_bulk_prepare_enable(res->num_clks, res->clks);
- }
-
- static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
diff --git a/target/linux/qualcommax/patches-6.12/0049-v6.10-arm64-dts-qcom-ipq8074-Add-PCIe-bridge-node.patch b/target/linux/qualcommax/patches-6.12/0049-v6.10-arm64-dts-qcom-ipq8074-Add-PCIe-bridge-node.patch
deleted file mode 100644
index 8a27278577..0000000000
--- a/target/linux/qualcommax/patches-6.12/0049-v6.10-arm64-dts-qcom-ipq8074-Add-PCIe-bridge-node.patch
+++ /dev/null
@@ -1,52 +0,0 @@
-From ed3893f6f9b800ca774f63810c5f8838bc7cee78 Mon Sep 17 00:00:00 2001
-From: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
-Date: Thu, 21 Mar 2024 16:46:35 +0530
-Subject: [PATCH] arm64: dts: qcom: ipq8074: Add PCIe bridge node
-
-On Qcom SoCs, the PCIe host bridge is connected to a single PCIe bridge
-for each controller instance. Hence, add a node to represent the bridge.
-
-Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
-Reviewed-by: Konrad Dybcio <konrad.dybcio at linaro.org>
-Link: https://lore.kernel.org/r/20240321-pcie-qcom-bridge-dts-v2-15-1eb790c53e43@linaro.org
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- arch/arm64/boot/dts/qcom/ipq8074.dtsi | 20 ++++++++++++++++++++
- 1 file changed, 20 insertions(+)
-
---- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
-+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
-@@ -878,6 +878,16 @@
- "ahb",
- "axi_m_sticky";
- status = "disabled";
-+
-+ pcie at 0 {
-+ device_type = "pci";
-+ reg = <0x0 0x0 0x0 0x0 0x0>;
-+ bus-range = <0x01 0xff>;
-+
-+ #address-cells = <3>;
-+ #size-cells = <2>;
-+ ranges;
-+ };
- };
-
- pcie0: pci at 20000000 {
-@@ -943,6 +953,16 @@
- "axi_m_sticky",
- "axi_s_sticky";
- status = "disabled";
-+
-+ pcie at 0 {
-+ device_type = "pci";
-+ reg = <0x0 0x0 0x0 0x0 0x0>;
-+ bus-range = <0x01 0xff>;
-+
-+ #address-cells = <3>;
-+ #size-cells = <2>;
-+ ranges;
-+ };
- };
- };
-
diff --git a/target/linux/qualcommax/patches-6.12/0050-v6.10-arm64-dts-qcom-ipq6018-Add-PCIe-bridge-node.patch b/target/linux/qualcommax/patches-6.12/0050-v6.10-arm64-dts-qcom-ipq6018-Add-PCIe-bridge-node.patch
deleted file mode 100644
index e831cd437a..0000000000
--- a/target/linux/qualcommax/patches-6.12/0050-v6.10-arm64-dts-qcom-ipq6018-Add-PCIe-bridge-node.patch
+++ /dev/null
@@ -1,35 +0,0 @@
-From 52358c64937e982d3cdcf64be58f08f30d8e518c Mon Sep 17 00:00:00 2001
-From: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
-Date: Thu, 21 Mar 2024 16:46:36 +0530
-Subject: [PATCH] arm64: dts: qcom: ipq6018: Add PCIe bridge node
-
-On Qcom SoCs, the PCIe host bridge is connected to a single PCIe bridge
-for each controller instance. Hence, add a node to represent the bridge.
-
-Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
-Reviewed-by: Konrad Dybcio <konrad.dybcio at linaro.org>
-Link: https://lore.kernel.org/r/20240321-pcie-qcom-bridge-dts-v2-16-1eb790c53e43@linaro.org
-Signed-off-by: Bjorn Andersson <andersson at kernel.org>
----
- arch/arm64/boot/dts/qcom/ipq6018.dtsi | 10 ++++++++++
- 1 file changed, 10 insertions(+)
-
---- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
-+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
-@@ -911,6 +911,16 @@
- "axi_s_sticky";
-
- status = "disabled";
-+
-+ pcie at 0 {
-+ device_type = "pci";
-+ reg = <0x0 0x0 0x0 0x0 0x0>;
-+ bus-range = <0x01 0xff>;
-+
-+ #address-cells = <3>;
-+ #size-cells = <2>;
-+ ranges;
-+ };
- };
- };
-
More information about the lede-commits
mailing list