[openwrt/openwrt] ramips: mt76x8: add support for Keenetic Launcher (KN-1221)
LEDE Commits
lede-commits at lists.infradead.org
Mon Mar 31 14:50:35 PDT 2025
hauke pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/ef20327e33fb38220ba0bca4418464749305e555
commit ef20327e33fb38220ba0bca4418464749305e555
Author: Ivan Davydov <lotigara at lotigara.ru>
AuthorDate: Tue Mar 4 23:54:13 2025 +0300
ramips: mt76x8: add support for Keenetic Launcher (KN-1221)
Specification:
SoC: MediaTek MT7628AN
RAM: 128M DDR2, ESMT M14D128168A (2Y)
Flash: 32M, cFeon EN25QH256A (Dual Boot on OEM, concatenated on OpenWrt,
SPI)
Switch: MediaTek MT7628AN, 3 ports 100 Mbps
WiFi: MediaTek MT7628AN 2.4 GHz 802.11n
USB: 1 port USB 2.0
GPIO: 1 button (Wi-Fi & Reset on OEM, Reset on OpenWrt), 3 LEDs (Power,
Internet, Wi-Fi), USB port power controls
Disassembly:
There are 2 screws at the bottom near the LEDs hidden by rubber mounts.
After removing the screws, pry the gray plastic part around (it is secured
with latches) and remove it.
UART Interface:
The UART interface can be connected to the 5 pin located between LAN
ports and the WAN one.
Pins (from the second LAN port to the WAN one): VCC, TX, RX, NC, GND
Settings: 115200, 8N1
Flashing via TFTP:
1. Connect your PC and router to the first LAN port, configure PC
interface using IP 192.168.1.2, mask 255.255.255.0
2. Serve the firmware image (for OpenWrt it is *-squashfs-factory.bin)
renamed to KN-1221_recovery.bin via TFTP
3. Power up the router while pressing Wi-Fi button
4. Release Wi-Fi button when Power LED starts blinking
To revert back to OEM firmware:
The return to the OEM firmware is carried out by using the methods
described above with the help of the appropriate firmware image found on
osvault.keenetic.net.
When using OEM bootloader, the firmware image size cannot exceed the size
of one OEM «Firmware_x» partition or Kernel + rootFS size.
Signed-off-by: Ivan Davydov <lotigara at lotigara.ru>
Link: https://github.com/openwrt/openwrt/pull/18164
Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
---
.../linux/ramips/dts/mt7628an_keenetic_kn-1221.dts | 209 +++++++++++++++++++++
target/linux/ramips/image/mt76x8.mk | 12 ++
.../ramips/mt76x8/base-files/etc/board.d/01_leds | 1 +
.../mt76x8/base-files/etc/board.d/02_network | 5 +
4 files changed, 227 insertions(+)
diff --git a/target/linux/ramips/dts/mt7628an_keenetic_kn-1221.dts b/target/linux/ramips/dts/mt7628an_keenetic_kn-1221.dts
new file mode 100644
index 0000000000..6f5cf96856
--- /dev/null
+++ b/target/linux/ramips/dts/mt7628an_keenetic_kn-1221.dts
@@ -0,0 +1,209 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7628an.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ compatible = "keenetic,kn-1221", "mediatek,mt7628an-soc";
+ model = "Keenetic KN-1221";
+
+ aliases {
+ label-mac-device = ðernet;
+
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ regulator-usb {
+ compatible = "regulator-fixed";
+ regulator-name = "USB-power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpios = <&gpio 6 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+ };
+
+ internet {
+ function = LED_FUNCTION_WAN;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
+ };
+
+ fn {
+ function = LED_FUNCTION_WLAN;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "restart";
+ gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ virtual_flash {
+ compatible = "mtd-concat";
+ devices = <&firmware1 &firmware2>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x0 0x1cc0000>;
+ };
+ };
+ };
+};
+
+&state_default {
+ gpio {
+ groups = "i2c", "spi cs1", "gpio", "refclk", "wdt";
+ function = "gpio";
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <32000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition at 30000 {
+ label = "u-config";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "rf-eeprom";
+ reg = <0x40000 0x10000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ eeprom_factory_0: eeprom at 0 {
+ reg = <0x0 0x400>;
+ };
+
+ macaddr_factory_4: macaddr at 4 {
+ reg = <0x4 0x6>;
+ };
+ };
+ };
+
+ firmware1: partition at 50000 {
+ label = "firmware_1";
+ reg = <0x50000 0xe60000>;
+ };
+
+ partition at eb0000 {
+ label = "config_1";
+ reg = <0xeb0000 0x40000>;
+ read-only;
+ };
+
+ partition at ef0000 {
+ label = "storage";
+ reg = <0xef0000 0x100000>;
+ read-only;
+ };
+
+ partition at ff0000 {
+ label = "dump";
+ reg = <0xff0000 0x10000>;
+ read-only;
+ };
+
+ partition at 1000000 {
+ label = "u-state";
+ reg = <0x1000000 0x30000>;
+ read-only;
+ };
+
+ partition at 1030000 {
+ label = "u-config_res";
+ reg = <0x1030000 0x10000>;
+ read-only;
+ };
+
+ partition at 1040000 {
+ label = "rf-eeprom_res";
+ reg = <0x1040000 0x10000>;
+ read-only;
+ };
+
+ firmware2: partition at 1050000 {
+ label = "firmware_2";
+ reg = <0x1050000 0xe60000>;
+ };
+
+ partition at 1eb0000 {
+ label = "Config_2";
+ reg = <0x1eb0000 0x40000>;
+ read-only;
+ };
+ };
+ };
+};
+
+ðernet {
+ nvmem-cells = <&macaddr_factory_4>;
+ nvmem-cell-names = "mac-address";
+};
+
+&esw {
+ mediatek,portmap = <0x3e>;
+ mediatek,portdisable = <0x38>;
+};
+
+&wmac {
+ status = "okay";
+
+ nvmem-cells = <&eeprom_factory_0>;
+ nvmem-cell-names = "eeprom";
+};
diff --git a/target/linux/ramips/image/mt76x8.mk b/target/linux/ramips/image/mt76x8.mk
index 8c8cfee23b..f442148d9e 100644
--- a/target/linux/ramips/image/mt76x8.mk
+++ b/target/linux/ramips/image/mt76x8.mk
@@ -366,6 +366,18 @@ define Device/jotale_js76x8-32m
endef
TARGET_DEVICES += jotale_js76x8-32m
+define Device/keenetic_kn-1221
+ BLOCKSIZE := 64k
+ IMAGE_SIZE := 29440k
+ DEVICE_VENDOR := Keenetic
+ DEVICE_MODEL := KN-1221
+ DEVICE_PACKAGES := kmod-usb2
+ IMAGES += factory.bin
+ IMAGE/factory.bin := $$(sysupgrade_bin) | pad-to $$$$(BLOCKSIZE) | \
+ check-size 14720k | zyimage -d 0x801221 -v "KN-1221"
+endef
+TARGET_DEVICES += keenetic_kn-1221
+
define Device/keenetic_kn-1613
IMAGE_SIZE := 15073280
DEVICE_VENDOR := Keenetic
diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
index b87062ae3c..79f78a2a45 100644
--- a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
@@ -58,6 +58,7 @@ hiwifi,hc5661a|\
hiwifi,hc5761a)
ucidef_set_led_switch "internet" "internet" "blue:internet" "switch0" "0x10"
;;
+keenetic,kn-1221|\
keenetic,kn-1613|\
keenetic,kn-1711|\
keenetic,kn-1713)
diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
index fbdc7fb5a2..6e6e1310d3 100644
--- a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
@@ -131,6 +131,10 @@ ramips_setup_interfaces()
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "6 at eth0"
;;
+ keenetic,kn-1221)
+ ucidef_add_switch "switch0" \
+ "1:lan" "2:lan" "0:wan" "6 at eth0"
+ ;;
keenetic,kn-1613|\
keenetic,kn-1713|\
motorola,mwr03)
@@ -287,6 +291,7 @@ ramips_setup_macs()
totolink,lr1200)
wan_mac=$(mtd_get_mac_binary factory 0x2e)
;;
+ keenetic,kn-1221|\
keenetic,kn-1613|\
keenetic,kn-3211|\
zyxel,keenetic-extra-ii)
More information about the lede-commits
mailing list