[openwrt/openwrt] qualcommax: ipq60xx: add Linksys MR7500 support
LEDE Commits
lede-commits at lists.infradead.org
Fri Mar 28 04:38:42 PDT 2025
robimarko pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/a1bf306bb71cfaf7e98c15320a6f3f487935f1b5
commit a1bf306bb71cfaf7e98c15320a6f3f487935f1b5
Author: Weikai Kong <priv at pppig236.com>
AuthorDate: Sat Dec 21 18:49:15 2024 -0500
qualcommax: ipq60xx: add Linksys MR7500 support
Codename: Divo
Hardware specification:
========
SoC: Qualcomm IPQ6018
RAM: 512MB (2x ESMT 256MB DDR3L M15T2G16128A–DEBG2R)
NAND Flash: 512MB (Macronix MX30UF4G18AC or SK Hynix H27S4G8F2EDA-BC)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C-B0)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4 at 20/40/160 MHz (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 2x2 at 20/40/80 MHz (Qualcomm QCN5052 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 2x2 at 20/40 MHz (Qualcomm QCN5022 + Skyworks SKY8340-11)
IoT: Bluetooth 5 (CSR8811) - not implemented
LED: 1x RGB status + USB Blue (PWM)
USB: 1x USB 3.0
Button: WPS, Reset
Flash instructions (Without Serial):
========
Open Linksys Web UI - http://192.168.1.1/ca or http://linksysxxxxx.lan/ca depending on your setup.
xxxxx is the last 5 digits from the SN found on a sticker under the device.
Click on the Linksys Logo to by-pass smart app registration.
Login with your admin password. The default password can be found on the same sticker.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
Flash instructions (With Serial):
========
1. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd13 0 0
- nandwrite -p /dev/mtd13 openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd15 0 0
- nandwrite -p /dev/mtd15 openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin alt_kernel
2. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq60xx-linksys_mr7500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware:
- mtd -e kernel -n write FW_MR7500_1.1.12.211919_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MR7500_1.1.12.211919_prod.img alt_kernel
4. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq60xx-linksys_mr7500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
AQR firmware:
========
0. Firmware extracting:
To extract the firmware, use unblob (unblob.org)
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
2. Firmware updating:
Newer firmware (AQR114C.cld) is available in the latest OEM firmware (https://downloads.linksys.com/support/assets/firmware/FW_MR7500_1.1.12.211919_prod.img).
Copy AQR114C.cld to /lib/firmware/marvell
Link: openwrt#17428
Signed-off-by: Weikai Kong <priv at pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko at gmail.com>
---
.../uboot-envtools/files/qualcommax_ipq60xx | 7 +-
package/firmware/ipq-wifi/Makefile | 2 +
.../arch/arm64/boot/dts/qcom/ipq6018-mr7500.dts | 544 +++++++++++++++++++++
target/linux/qualcommax/image/ipq60xx.mk | 12 +
.../ipq60xx/base-files/etc/board.d/01_leds | 12 +
.../ipq60xx/base-files/etc/board.d/02_network | 1 +
.../etc/hotplug.d/firmware/11-ath11k-caldata | 11 +-
.../ipq60xx/base-files/etc/init.d/bootcount | 3 +-
.../ipq60xx/base-files/lib/upgrade/platform.sh | 3 +-
9 files changed, 589 insertions(+), 6 deletions(-)
diff --git a/package/boot/uboot-tools/uboot-envtools/files/qualcommax_ipq60xx b/package/boot/uboot-tools/uboot-envtools/files/qualcommax_ipq60xx
index aa01e040ea..ba6d9ff1fa 100644
--- a/package/boot/uboot-tools/uboot-envtools/files/qualcommax_ipq60xx
+++ b/package/boot/uboot-tools/uboot-envtools/files/qualcommax_ipq60xx
@@ -21,13 +21,14 @@ cambiumnetworks,xe3-4)
;;
glinet,gl-ax1800|\
glinet,gl-axt1800|\
+linksys,mr7350|\
+linksys,mr7500)
+ ubootenv_add_mtd "u_env" "0x0" "0x40000" "0x20000"
+ ;;
netgear,wax214|\
tplink,eap610-outdoor)
ubootenv_add_mtd "0:appsblenv" "0x0" "0x40000" "0x20000"
;;
-linksys,mr7350)
- ubootenv_add_mtd "u_env" "0x0" "0x40000" "0x20000"
- ;;
yuncore,fap650)
ubootenv_add_mtd "0:appsblenv" "0x0" "0x10000" "0x10000"
;;
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile
index b9009cf532..107f5ffed2 100644
--- a/package/firmware/ipq-wifi/Makefile
+++ b/package/firmware/ipq-wifi/Makefile
@@ -43,6 +43,7 @@ ALLWIFIBOARDS:= \
linksys_homewrk \
linksys_mr5500 \
linksys_mr7350 \
+ linksys_mr7500 \
linksys_mx2000 \
linksys_mx4200 \
linksys_mx5300 \
@@ -188,6 +189,7 @@ $(eval $(call generate-ipq-wifi-package,glinet_gl-axt1800,GL.iNet GL-AXT1800))
$(eval $(call generate-ipq-wifi-package,linksys_homewrk,Linksys HomeWRK))
$(eval $(call generate-ipq-wifi-package,linksys_mr5500,Linksys MR5500))
$(eval $(call generate-ipq-wifi-package,linksys_mr7350,Linksys MR7350))
+$(eval $(call generate-ipq-wifi-package,linksys_mr7500,Linksys MR7500))
$(eval $(call generate-ipq-wifi-package,linksys_mx2000,Linksys MX2000))
$(eval $(call generate-ipq-wifi-package,linksys_mx4200,Linksys MX4200))
$(eval $(call generate-ipq-wifi-package,linksys_mx5300,Linksys MX5300))
diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq6018-mr7500.dts b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq6018-mr7500.dts
new file mode 100644
index 0000000000..9cfd3a5239
--- /dev/null
+++ b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq6018-mr7500.dts
@@ -0,0 +1,544 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+// Copyright 2024 Weikai Kong (priv at pppig236.com)
+
+/dts-v1/;
+
+#include "ipq6018-512m.dtsi"
+#include "ipq6018-cp-cpu.dtsi"
+#include "ipq6018-ess.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Linksys MR7500";
+ compatible = "linksys,mr7500", "qcom,ipq6018";
+
+ aliases {
+ serial0 = &blsp1_uart3;
+ serial1 = &blsp1_uart2;
+
+ led-boot = &led_system_blue;
+ led-running = &led_system_blue;
+ led-failsafe = &led_system_red;
+ led-upgrade = &led_system_green;
+
+ label-mac-device = &dp5_syn;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs-append = " root=/dev/ubiblock0_0";
+ };
+
+ extcon_usb {
+ pinctrl-0 = <&extcon_usb_pins>;
+ pinctrl-names = "default";
+ id-gpio = <&tlmm 26 GPIO_ACTIVE_LOW>;
+ status = "okay";
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&button_pins>;
+ pinctrl-names = "default";
+
+ wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&tlmm 37 GPIO_ACTIVE_LOW>;
+ };
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&tlmm 56 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "pwm-leds";
+
+ usb {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_USB;
+ gpios = <&tlmm 30 GPIO_ACTIVE_HIGH>;
+ pwms = <&pwm 1 650000>;
+ max-brightness = <255>;
+ trigger-sources = <&usb3_port1>, <&usb3_port2>;
+ linux,default-trigger = "usbport";
+ };
+
+ led_system_red: red {
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_INDICATOR;
+ pwms = <&pwm 2 1250000>;
+ max-brightness = <255>;
+ panic-indicator;
+ };
+
+ led_system_green: green {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_INDICATOR;
+ pwms = <&pwm 3 1250000>;
+ max-brightness = <255>;
+ };
+
+ led_system_blue: blue {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_POWER;
+ pwms = <&pwm 0 1250000>;
+ max-brightness = <255>;
+ };
+ };
+
+ reg_usb_vbus: regulator-usb-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&tlmm 25 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&tlmm {
+ pwm_pins: pwm_pinmux {
+ /*LED_B*/
+ mux_0 {
+ pins = "gpio29";
+ function = "pwm03";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ /*LED_USB*/
+ mux_1 {
+ pins = "gpio30";
+ function = "pwm13";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+
+ /*LED_R*/
+ mux_2 {
+ pins = "gpio31";
+ function = "pwm23";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+
+ /*LED_G*/
+ mux_3 {
+ pins = "gpio32";
+ function = "pwm33";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+ };
+
+ extcon_usb_pins: extcon_usb_pins {
+ pins = "gpio26";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ button_pins: button_pins {
+ wps_button {
+ pins = "gpio37";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ reset_button {
+ pins = "gpio56";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+
+ mdio_pins: mdio_pinmux {
+ mux_0 {
+ pins = "gpio64";
+ function = "mdc";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ mux_1 {
+ pins = "gpio65";
+ function = "mdio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+
+ hsuart_pins: hsuart_pins {
+ pins = "gpio71", "gpio72", "gpio69", "gpio70";
+ function = "blsp1_uart";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ btcoex_pins: btcoex_pins {
+ mux_0 {
+ pins = "gpio51";
+ function = "pta1_1";
+ drive-strength = <6>;
+ bias-pull-down;
+ };
+ mux_1 {
+ pins = "gpio53";
+ function = "pta1_0";
+ drive-strength = <6>;
+ bias-pull-down;
+ };
+ mux_2 {
+ pins = "gpio52";
+ function = "pta1_2";
+ drive-strength = <6>;
+ bias-pull-down;
+ };
+ };
+};
+
+&pwm {
+ pinctrl-0 = <&pwm_pins>;
+ pinctrl-names = "default";
+ #pwm-cells = <2>;
+ status = "okay";
+};
+
+&mdio {
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ reset-gpios = <&tlmm 75 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ ethernet-phy-package {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "qcom,qca8075-package";
+ reg = <0>;
+
+ qcom,package-mode = "qsgmii";
+
+ qca8075_0: ethernet-phy at 0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led at 0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_ORANGE>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+
+ led at 1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+ };
+ };
+
+ qca8075_1: ethernet-phy at 1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led at 0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_ORANGE>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+
+ led at 1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+ };
+ };
+
+ qca8075_2: ethernet-phy at 2 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <2>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led at 0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_ORANGE>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+
+ led at 1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+ };
+ };
+
+ qca8075_3: ethernet-phy at 3 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <3>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led at 0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_ORANGE>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+
+ led at 1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+ };
+ };
+ };
+
+ aqr114c: ethernet-phy at 8 {
+ reg = <8>;
+ reset-gpios = <&tlmm 77 GPIO_ACTIVE_HIGH>;
+ compatible = "ethernet-phy-ieee802.3-c45";
+ firmware-name = "marvell/AQR114C.cld";
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led at 0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_ORANGE>;
+ function = LED_FUNCTION_WAN;
+ default-state = "keep";
+ };
+
+ led at 1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_WAN;
+ default-state = "keep";
+ };
+ };
+ };
+};
+
+&dp1 {
+ status = "okay";
+ label = "lan1";
+ phy-handle = <&qca8075_0>;
+ phy-mode = "qsgmii";
+ nvmem-cells = <&hw_mac_addr 1>;
+ nvmem-cell-names = "mac-address";
+};
+
+&dp2 {
+ status = "okay";
+ label = "lan2";
+ phy-handle = <&qca8075_1>;
+ phy-mode = "qsgmii";
+ nvmem-cells = <&hw_mac_addr 1>;
+ nvmem-cell-names = "mac-address";
+};
+
+&dp3 {
+ status = "okay";
+ label = "lan3";
+ phy-handle = <&qca8075_2>;
+ phy-mode = "qsgmii";
+ nvmem-cells = <&hw_mac_addr 1>;
+ nvmem-cell-names = "mac-address";
+};
+
+&dp4 {
+ status = "okay";
+ label = "lan4";
+ phy-handle = <&qca8075_3>;
+ phy-mode = "qsgmii";
+ nvmem-cells = <&hw_mac_addr 1>;
+ nvmem-cell-names = "mac-address";
+};
+
+&dp5_syn {
+ status = "okay";
+ label = "wan";
+ phy-handle = <&aqr114c>;
+ phy-mode = "usxgmii";
+ nvmem-cells = <&hw_mac_addr 0>;
+ nvmem-cell-names = "mac-address";
+};
+
+&edma {
+ status = "okay";
+};
+
+&switch {
+ status = "okay";
+ switch_lan_bmp = <( ESS_PORT1 | ESS_PORT2 | ESS_PORT3 | ESS_PORT4 )>;
+ switch_wan_bmp = <ESS_PORT5>;
+ switch_mac_mode = <MAC_MODE_QSGMII>;
+ switch_mac_mode1 = <MAC_MODE_USXGMII>;
+
+ qcom,port_phyinfo {
+ port at 1 {
+ port_id = <1>;
+ phy_address = <0>;
+ };
+ port at 2 {
+ port_id = <2>;
+ phy_address = <1>;
+ };
+ port at 3 {
+ port_id = <3>;
+ phy_address = <2>;
+ };
+ port at 4 {
+ port_id = <4>;
+ phy_address = <3>;
+ };
+ port at 5 {
+ port_id = <5>;
+ phy_address = <8>;
+ compatible = "ethernet-phy-ieee802.3-c45";
+ ethernet-phy-ieee802.3-c45;
+ };
+ };
+};
+
+&blsp1_uart3 {
+ pinctrl-0 = <&serial_3_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&blsp1_uart2 {
+ pinctrl-0 = <&hsuart_pins &btcoex_pins>;
+ pinctrl-names = "default";
+ dmas = <&blsp_dma 2>, <&blsp_dma 3>;
+ dma-names = "tx", "rx";
+ status = "okay";
+ bluetooth { // doesn't work
+ compatible = "csr,8811";
+ enable-gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&qpic_nand {
+ status = "okay";
+
+ nand at 0 {
+ reg = <0>;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ nand-bus-width = <8>;
+
+ partitions {
+ compatible = "qcom,smem-part";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition-0-devinfo {
+ label = "devinfo";
+ read-only;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ nvmem-layout {
+ compatible = "ascii-eq-delim-env";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ hw_mac_addr: hw_mac_addr {
+ compatible = "mac-base";
+ #nvmem-cell-cells = <1>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&ssphy_0 {
+ status = "okay";
+};
+
+&dwc_0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb3_port1: port at 1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+
+ usb3_port2: port at 2 {
+ reg = <2>;
+ #trigger-source-cells = <0>;
+ };
+};
+
+&qusb_phy_0 {
+ status = "okay";
+ vdd-supply = <®_usb_vbus>;
+};
+
+&usb3 {
+ status = "okay";
+ vbus-supply = <®_usb_vbus>;
+};
+
+&pcie_phy {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+ bridge at 0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi at 1,0 {
+ status = "okay";
+ /* ath11k has no DT compatible for PCI cards */
+ compatible = "pci17cb,1104";
+ reg = <0x00010000 0 0 0 0>;
+ qcom,ath11k-calibration-variant = "Linksys-MR7500";
+ };
+ };
+};
+
+&wifi {
+ status = "okay";
+ qcom,ath11k-calibration-variant = "Linksys-MR7500";
+ qcom,ath11k-fw-memory-mode = <1>;
+};
diff --git a/target/linux/qualcommax/image/ipq60xx.mk b/target/linux/qualcommax/image/ipq60xx.mk
index 03e49b97f7..41e06c5384 100644
--- a/target/linux/qualcommax/image/ipq60xx.mk
+++ b/target/linux/qualcommax/image/ipq60xx.mk
@@ -75,6 +75,18 @@ define Device/linksys_mr7350
endef
TARGET_DEVICES += linksys_mr7350
+define Device/linksys_mr7500
+ $(call Device/linksys_mr)
+ DEVICE_MODEL := MR7500
+ SOC := ipq6018
+ NAND_SIZE := 512m
+ IMAGE_SIZE := 147456k
+ DEVICE_PACKAGES += ipq-wifi-linksys_mr7500 \
+ ath11k-firmware-qcn9074 kmod-ath11k-pci \
+ kmod-leds-pwm kmod-phy-aquantia
+endef
+TARGET_DEVICES += linksys_mr7500
+
define Device/netgear_wax214
$(call Device/FitImage)
$(call Device/UbiFit)
diff --git a/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/01_leds b/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/01_leds
index a9575eb4ef..75735fd5ff 100644
--- a/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/01_leds
+++ b/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/01_leds
@@ -19,6 +19,18 @@ linksys,mr7350)
ucidef_set_led_netdev "wan-port-link" "WAN-PORT-LINK" "90000.mdio-1:04:green:wan" "wan" "link_10 link_100 link_1000"
ucidef_set_led_netdev "wan-port-traffic" "WAN-PORT-TRAFFIC" "90000.mdio-1:04:orange:wan" "wan" "tx rx link_10 link_100 link_1000"
;;
+linksys,mr7500)
+ ucidef_set_led_netdev "lan1-port-link" "LAN1-PORT-LINK" "90000.mdio-1:00:green:lan" "lan1" "link_10 link_100 link_1000"
+ ucidef_set_led_netdev "lan1-port-traffic" "LAN1-PORT-TRAFFIC" "90000.mdio-1:00:orange:lan" "lan1" "tx rx link_10 link_100 link_1000"
+ ucidef_set_led_netdev "lan2-port-link" "LAN2-PORT-LINK" "90000.mdio-1:01:green:lan" "lan2" "link_10 link_100 link_1000"
+ ucidef_set_led_netdev "lan2-port-traffic" "LAN2-PORT-TRAFFIC" "90000.mdio-1:01:orange:lan" "lan2" "tx rx link_10 link_100 link_1000"
+ ucidef_set_led_netdev "lan3-port-link" "LAN3-PORT-LINK" "90000.mdio-1:02:green:lan" "lan3" "link_10 link_100 link_1000"
+ ucidef_set_led_netdev "lan3-port-traffic" "LAN3-PORT-TRAFFIC" "90000.mdio-1:02:orange:lan" "lan3" "tx rx link_10 link_100 link_1000"
+ ucidef_set_led_netdev "lan4-port-link" "LAN4-PORT-LINK" "90000.mdio-1:03:green:lan" "lan4" "link_10 link_100 link_1000"
+ ucidef_set_led_netdev "lan4-port-traffic" "LAN4-PORT-TRAFFIC" "90000.mdio-1:03:orange:lan" "lan4" "tx rx link_10 link_100 link_1000"
+ ucidef_set_led_netdev "wan-port-link" "WAN-PORT-LINK" "90000.mdio-1:08:green:lan" "wan" "link_10 link_100 link_1000 link_2500 link_5000"
+ ucidef_set_led_netdev "wan-port-traffic" "WAN-PORT-TRAFFIC" "90000.mdio-1:08:orange:wan" "wan" "tx rx link_10 link_100 link_1000 link_2500 link_5000"
+ ;;
yuncore,fap650)
ucidef_set_led_netdev "wlan5ghz" "WLAN 5GHz LED" "blue:wlan-5ghz" "wlan0" "tx rx"
ucidef_set_led_netdev "wlan2ghz" "WLAN 2.4GHz LED" "green:wlan-2ghz" "wlan1" "tx rx"
diff --git a/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network b/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network
index 3fa86a37f1..e45bc32fb4 100644
--- a/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network
+++ b/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network
@@ -20,6 +20,7 @@ ipq60xx_setup_interfaces()
;;
glinet,gl-ax1800|\
linksys,mr7350|\
+ linksys,mr7500|\
yuncore,fap650)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
;;
diff --git a/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11k-caldata b/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
index 061d2ad2ea..0d240cd4f7 100644
--- a/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
+++ b/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
@@ -23,12 +23,14 @@ case "$FIRMWARE" in
ath11k_patch_mac $(macaddr_add $label_mac 2) 1
ath11k_set_macflag
;;
- linksys,mr7350)
+ linksys,mr7350|\
+ linksys,mr7500)
caldata_extract "0:art" 0x1000 0x10000
addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
ath11k_patch_mac $(macaddr_add $addr 2) 0
ath11k_patch_mac $(macaddr_add $addr 1) 1
ath11k_set_macflag
+ ath11k_remove_regdomain
;;
netgear,wax214)
caldata_extract "0:art" 0x1000 0x10000
@@ -57,6 +59,13 @@ case "$FIRMWARE" in
cambiumnetworks,xe3-4)
caldata_extract "0:ART" 0x26800 0x20000
;;
+ linksys,mr7500)
+ caldata_extract "0:art" 0x26800 0x20000
+ addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
+ ath11k_patch_mac $(macaddr_add $addr 3) 0
+ ath11k_set_macflag
+ ath11k_remove_regdomain
+ ;;
esac
;;
*)
diff --git a/target/linux/qualcommax/ipq60xx/base-files/etc/init.d/bootcount b/target/linux/qualcommax/ipq60xx/base-files/etc/init.d/bootcount
index fbe245d988..d2039eb054 100755
--- a/target/linux/qualcommax/ipq60xx/base-files/etc/init.d/bootcount
+++ b/target/linux/qualcommax/ipq60xx/base-files/etc/init.d/bootcount
@@ -4,7 +4,8 @@ START=99
boot() {
case $(board_name) in
- linksys,mr7350)
+ linksys,mr7350|\
+ linksys,mr7500)
mtd resetbc s_env || true
;;
yuncore,fap650)
diff --git a/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh b/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh
index b9b0ed1ed7..59e5ef7ca2 100644
--- a/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh
@@ -116,7 +116,8 @@ platform_do_upgrade() {
qihoo,360v6)
nand_do_upgrade "$1"
;;
- linksys,mr7350)
+ linksys,mr7350|\
+ linksys,mr7500)
boot_part="$(fw_printenv -n boot_part)"
if [ "$boot_part" -eq "1" ]; then
fw_setenv boot_part 2
More information about the lede-commits
mailing list