[openwrt/openwrt] ath79: add support for Dell SonicPoint ACi APL27-0B1

LEDE Commits lede-commits at lists.infradead.org
Sat Jul 12 16:04:07 PDT 2025


hauke pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/a89eced3ab2cc8dde322d750a39b4f33369aaa36

commit a89eced3ab2cc8dde322d750a39b4f33369aaa36
Author: Tomasz Maciej Nowak <tmn505 at gmail.com>
AuthorDate: Thu May 29 22:15:16 2025 +0200

    ath79: add support for Dell SonicPoint ACi APL27-0B1
    
    Dell/SonicWall APL27-0B1 (marketed as SonicPoint ACi) is a dual band
    wireless access point. Very similar to already supported APL26-0AE,
    which all antennas are external, while this variant has internal
    antennas. End of life as of 2022-07-31.
    
    Specification
    SoC: QualcommAtheros QCA9550
    RAM: 256 MB DDR2
    Flash: 32 MB SPI NOR
    WIFI: 2.4 GHz 3T3R integrated
          5 GHz 3T3R QCA9890 oversized Mini PCIe card
    Ethernet: 2x 10/100/1000 Mbps QCA8334
              port labeled lan1 is PoE capable (802.3at)
    USB: 1x 2.0
    LEDs: LEDs: 6x which 5 are GPIO controlled and two of them are dual color
    Buttons: 1x GPIO controlled
    Serial: RJ-45 port, SonicWall pinout
            baud: 115200, parity: none, flow control: none
    
    Before flashing, be sure to have a copy of factory firmware, in case You
    wish to revert to original firmware.
    
    Installation
    1. Prepare TFTP server with OpenWrt sysupgrade image and rename that
       image to "ap135.bin".
    2. Connect to one of LAN ports.
    3. Connect to serial port.
    4. Hold the reset button (small through hole on side of the unit),
       power on the device and when prompted to stop autoboot, hit any key.
       The held button can now be released.
    5. Alter U-Boot environment with following commands:
        setenv bootcmd bootm 0x9F110000
        saveenv
    6. Adjust "ipaddr" (access point, default is 192.168.1.1) and "serverip"
       (TFTP server, default is 192.168.1.10) addresses in U-Boot
       environment, then run following commands:
        tftp 0x80060000 ap135.bin
        erase 0x9F110000 +0x1EF0000
        cp.b 0x80060000 0x9F110000 $filesize
    7. After successful flashing, execute:
        boot
    8. The access point will boot to OpenWrt. Wait few minutes, until the
        wrench LED will stop blinking, then it's ready for configuration.
    
    Notes
    By default no power is provided on USB port, so attached USB devices
    won't enumerate. To change that enable regulator with:
    echo "enabled" > /sys/devices/platform/output-usb-vbus/state
    To disable power write "disabled" to the same file.
    Ther regulator state will reset on reboot, consider running this command
    on hotplug event or add it to /etc/rc.local. The hotplug event should
    look like this:
    if [ "${PRODUCT}" = "1d6b/2/606" ] && [ "${ACTION}" = "add" ]; then
            echo "enabled" > /sys/devices/platform/output-usb-vbus/state
    fi
    Place it in /etc/hotplug.d/usb/10-usb-power.
    
    Known issues
    Initramfs image can't be bigger than specified kernel size, otherwise
    bootloader will throw LZMA decompressing error. Switching to lzma-loader
    should workaround that.
    
    Signed-off-by: Tomasz Maciej Nowak <tmn505 at gmail.com>
    Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250529202033.28250-2-tmn505@terefe.re/
    Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
---
 .../boot/uboot-tools/uboot-envtools/files/ath79    |   3 +-
 target/linux/ath79/dts/qca9550_dell_apl26-0ae.dts  | 167 +--------------------
 target/linux/ath79/dts/qca9550_dell_apl27-0b1.dts  |  78 ++++++++++
 ..._dell_apl26-0ae.dts => qca9550_dell_apl2x.dtsi} |  25 +--
 .../ath79/generic/base-files/etc/board.d/01_leds   |   3 +-
 .../generic/base-files/etc/board.d/02_network      |   3 +-
 target/linux/ath79/image/generic.mk                |  18 ++-
 7 files changed, 103 insertions(+), 194 deletions(-)

diff --git a/package/boot/uboot-tools/uboot-envtools/files/ath79 b/package/boot/uboot-tools/uboot-envtools/files/ath79
index f275244cbe..f544bfaf79 100644
--- a/package/boot/uboot-tools/uboot-envtools/files/ath79
+++ b/package/boot/uboot-tools/uboot-envtools/files/ath79
@@ -111,7 +111,8 @@ buffalo,wzr-hp-g300nh-s|\
 linksys,ea4500-v3)
 	ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000"
 	;;
-dell,apl26-0ae)
+dell,apl26-0ae|\
+dell,apl27-0b1)
 	ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x40000" "0x10000"
 	;;
 domywifi,dw33d)
diff --git a/target/linux/ath79/dts/qca9550_dell_apl26-0ae.dts b/target/linux/ath79/dts/qca9550_dell_apl26-0ae.dts
index 6ef2eb846d..044de5add3 100644
--- a/target/linux/ath79/dts/qca9550_dell_apl26-0ae.dts
+++ b/target/linux/ath79/dts/qca9550_dell_apl26-0ae.dts
@@ -1,29 +1,14 @@
 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-
-#include "qca955x.dtsi"
+#include "qca9550_dell_apl2x.dtsi"
 
 / {
 	model = "Dell SonicPoint ACe (APL26-0AE)";
 	compatible = "dell,apl26-0ae", "qca,qca9550", "qca,qca9558";
 
-	aliases {
-		label-mac-device = &eth0;
-		led-boot = &led_wrench;
-		led-failsafe = &led_wrench;
-		led-upgrade = &led_wrench;
-	};
-
 	keys {
-		compatible = "gpio-keys";
-
 		button-reset {
-			label = "reset";
 			gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_RESTART>;
 		};
 
 		/* Accessible only after disassembling the casing */
@@ -35,109 +20,38 @@
 	};
 
 	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&jtag_disable_pins>;
-
 		led-lan1-amber {
-			color = <LED_COLOR_ID_AMBER>;
-			function = LED_FUNCTION_LAN;
-			function-enumerator = <1>;
 			gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
 		};
 
 		led-lan1-green {
-			color = <LED_COLOR_ID_GREEN>;
-			function = LED_FUNCTION_LAN;
-			function-enumerator = <1>;
 			gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
 		};
 
 		led-lan2-amber {
-			color = <LED_COLOR_ID_AMBER>;
-			function = LED_FUNCTION_LAN;
-			function-enumerator = <2>;
 			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
 		};
 
 		led-lan2-green {
-			color = <LED_COLOR_ID_GREEN>;
-			function = LED_FUNCTION_LAN;
-			function-enumerator = <2>;
 			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
 		};
 
 		led-wlan2g {
-			color = <LED_COLOR_ID_GREEN>;
-			function = LED_FUNCTION_WLAN_2GHZ;
-			linux,default-trigger = "phy1tpt";
 			gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
 		};
 
 		led-wlan5g {
-			color = <LED_COLOR_ID_GREEN>;
-			function = LED_FUNCTION_WLAN_5GHZ;
-			linux,default-trigger = "phy0tpt";
 			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
 		};
 
-		led_wrench: led-wrench {
-			color = <LED_COLOR_ID_AMBER>;
-			function = LED_FUNCTION_STATUS;
+		led-wrench {
 			gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
 		};
 	};
 };
 
-&eth0 {
-	status = "okay";
-
-	nvmem-cells = <&macaddr_sysinfo_50 0>;
-	nvmem-cell-names = "mac-address";
-	phy-handle = <&phy0>;
-	pll-data = <0xa6000000 0x00000101 0x00001616>;
-};
-
-&eth1 {
-	status = "okay";
-
-	nvmem-cells = <&macaddr_sysinfo_50 1>;
-	nvmem-cell-names = "mac-address";
-	pll-data = <0x03000101 0x00000101 0x00001616>;
-
-	fixed-link {
-		speed = <1000>;
-		full-duplex;
-	};
-};
-
-&mdio0 {
-	status = "okay";
-
-	phy0: ethernet-phy at 0 {
-		reg = <0>;
-
-		qca,ar8327-initvals = <
-			0x04 0x07680000 /* PORT0 PAD MODE CTRL */
-			0x0c 0x00000080 /* PORT6 PAD MODE CTRL */
-			0x10 0x40000000 /* POWER_ON_STRAP */
-			0x50 0xffb7c405 /* LED0 CTRL */
-			0x54 0xffb7c305 /* LED1 CTRL */
-			0x58 0xffb7c033 /* LED2 CTRL */
-			0x5c 0x03ffff00 /* LED3 CTRL */
-			0x7c 0x0000007e /* PORT0_STATUS */
-			0x94 0x0000007e /* PORT6_STATUS */
-		>;
-	};
-};
-
 &pcie0 {
-	status = "okay";
-
 	wifi at 0,0 {
-		compatible = "qcom,ath10k";
-		reg = <0x0000 0 0 0 0>;
-
 		/* OEM overwrites EEPROM stored adress and so do we */
 		nvmem-cells = <&macaddr_sysinfo_50 2>;
 		nvmem-cell-names = "mac-address";
@@ -145,84 +59,7 @@
 };
 
 &spi {
-	status = "okay";
-
 	flash at 0 {
-		compatible = "jedec,spi-nor";
-		reg = <0>;
-		spi-max-frequency = <25000000>;
 		broken-flash-reset;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			partition at 0 {
-				label = "u-boot";
-				reg = <0x0000000 0x0080000>;
-				read-only;
-			};
-
-			partition at 80000 {
-				label = "u-boot-env";
-				reg = <0x0080000 0x0040000>;
-			};
-
-			partition at c0000 {
-				label = "sysinfo";
-				reg = <0x00c0000 0x0040000>;
-				read-only;
-
-				nvmem-layout {
-					compatible = "fixed-layout";
-					#address-cells = <1>;
-					#size-cells = <1>;
-
-					macaddr_sysinfo_50: macaddr at 50 {
-						compatible = "mac-base";
-						reg = <0x50 0x6>;
-						#nvmem-cell-cells = <1>;
-					};
-				};
-			};
-
-			partition at 100000 {
-				label = "art";
-				reg = <0x0100000 0x0010000>;
-				read-only;
-
-				nvmem-layout {
-					compatible = "fixed-layout";
-					#address-cells = <1>;
-					#size-cells = <1>;
-
-					cal_art_1000: calibration at 1000 {
-						reg = <0x1000 0x440>;
-					};
-				};
-			};
-
-			partition at 110000 {
-				label = "firmware";
-				reg = <0x0110000 0x1ef0000>;
-				compatible = "denx,uimage";
-			};
-		};
 	};
 };
-
-&usb_phy0 {
-	status = "okay";
-};
-
-&usb0 {
-	status = "okay";
-};
-
-&wmac {
-	status = "okay";
-
-	nvmem-cells = <&macaddr_sysinfo_50 10>, <&cal_art_1000>;
-	nvmem-cell-names = "mac-address", "calibration";
-};
diff --git a/target/linux/ath79/dts/qca9550_dell_apl27-0b1.dts b/target/linux/ath79/dts/qca9550_dell_apl27-0b1.dts
new file mode 100644
index 0000000000..28d78f29d2
--- /dev/null
+++ b/target/linux/ath79/dts/qca9550_dell_apl27-0b1.dts
@@ -0,0 +1,78 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca9550_dell_apl2x.dtsi"
+
+/ {
+	model = "Dell SonicPoint ACi (APL27-0B1)";
+	compatible = "dell,apl27-0b1", "qca,qca9550", "qca,qca9558";
+
+	keys {
+		button-reset {
+			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		led-lan1-amber {
+			gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+		};
+
+		led-lan1-green {
+			gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+		};
+
+		led-lan2-amber {
+			gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+		};
+
+		led-lan2-green {
+			gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wlan2g {
+			gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wlan5g {
+			gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wrench {
+			gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	reg_usb_vbus: regulator-usb-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+	};
+
+	output-usb-vbus {
+		compatible = "regulator-output";
+		vout-supply = <&reg_usb_vbus>;
+	};
+};
+
+&pcie0 {
+	wifi at 0,0 {
+		nvmem-cells = <&macaddr_sysinfo_50 2>, <&cal_art_5000>;
+		nvmem-cell-names = "mac-address", "calibration";
+	};
+};
+
+&spi {
+	flash at 0 {
+		partitions {
+			partition at 100000 {
+				nvmem-layout {
+					cal_art_5000: calibration at 5000 {
+						reg = <0x5000 0x844>;
+					};
+				};
+			};
+		};
+	};
+};
diff --git a/target/linux/ath79/dts/qca9550_dell_apl26-0ae.dts b/target/linux/ath79/dts/qca9550_dell_apl2x.dtsi
similarity index 83%
copy from target/linux/ath79/dts/qca9550_dell_apl26-0ae.dts
copy to target/linux/ath79/dts/qca9550_dell_apl2x.dtsi
index 6ef2eb846d..bcc558e0b1 100644
--- a/target/linux/ath79/dts/qca9550_dell_apl26-0ae.dts
+++ b/target/linux/ath79/dts/qca9550_dell_apl2x.dtsi
@@ -7,9 +7,6 @@
 #include "qca955x.dtsi"
 
 / {
-	model = "Dell SonicPoint ACe (APL26-0AE)";
-	compatible = "dell,apl26-0ae", "qca,qca9550", "qca,qca9558";
-
 	aliases {
 		label-mac-device = &eth0;
 		led-boot = &led_wrench;
@@ -22,16 +19,8 @@
 
 		button-reset {
 			label = "reset";
-			gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_RESTART>;
 		};
-
-		/* Accessible only after disassembling the casing */
-		button-service {
-			label = "service";
-			gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_POWER>;
-		};
 	};
 
 	leds {
@@ -43,48 +32,41 @@
 			color = <LED_COLOR_ID_AMBER>;
 			function = LED_FUNCTION_LAN;
 			function-enumerator = <1>;
-			gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
 		};
 
 		led-lan1-green {
 			color = <LED_COLOR_ID_GREEN>;
 			function = LED_FUNCTION_LAN;
 			function-enumerator = <1>;
-			gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
 		};
 
 		led-lan2-amber {
 			color = <LED_COLOR_ID_AMBER>;
 			function = LED_FUNCTION_LAN;
 			function-enumerator = <2>;
-			gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
 		};
 
 		led-lan2-green {
 			color = <LED_COLOR_ID_GREEN>;
 			function = LED_FUNCTION_LAN;
 			function-enumerator = <2>;
-			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
 		};
 
 		led-wlan2g {
 			color = <LED_COLOR_ID_GREEN>;
 			function = LED_FUNCTION_WLAN_2GHZ;
 			linux,default-trigger = "phy1tpt";
-			gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
 		};
 
 		led-wlan5g {
 			color = <LED_COLOR_ID_GREEN>;
 			function = LED_FUNCTION_WLAN_5GHZ;
 			linux,default-trigger = "phy0tpt";
-			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
 		};
 
 		led_wrench: led-wrench {
 			color = <LED_COLOR_ID_AMBER>;
 			function = LED_FUNCTION_STATUS;
-			gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
 		};
 	};
 };
@@ -137,10 +119,6 @@
 	wifi at 0,0 {
 		compatible = "qcom,ath10k";
 		reg = <0x0000 0 0 0 0>;
-
-		/* OEM overwrites EEPROM stored adress and so do we */
-		nvmem-cells = <&macaddr_sysinfo_50 2>;
-		nvmem-cell-names = "mac-address";
 	};
 };
 
@@ -151,7 +129,8 @@
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <25000000>;
-		broken-flash-reset;
+		#address-cells = <1>;
+		#size-cells = <1>;
 
 		partitions {
 			compatible = "fixed-partitions";
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index 4107563439..9ebdcdca6f 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -234,7 +234,8 @@ compex,wpj531-16m)
 	ucidef_set_led_rssi "sig3" "SIG3" "green:sig3" "wlan0" "65" "100"
 	ucidef_set_led_rssi "sig4" "SIG4" "green:sig4" "wlan0" "50" "100"
 	;;
-dell,apl26-0ae)
+dell,apl26-0ae|\
+dell,apl27-0b1)
 	ucidef_set_led_switch "lan1" "LAN1" "amber:lan-1" "switch0" "0x04"
 	ucidef_set_led_switch "lan2" "LAN2" "amber:lan-2" "switch0" "0x08"
 	;;
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index d999784d6a..545bc14e36 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -298,7 +298,8 @@ ath79_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"1:wan" "5:lan" "6 at eth0"
 		;;
-	dell,apl26-0ae)
+	dell,apl26-0ae|\
+	dell,apl27-0b1)
 		ucidef_add_switch "switch0" \
 			"0 at eth0" "2:lan:1" "3:lan:2" "6 at eth1"
 		;;
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index b74a22ba4d..6e97960207 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -978,22 +978,34 @@ define Device/compex_wpj563
 endef
 TARGET_DEVICES += compex_wpj563
 
-define Device/dell_apl26-0ae
+define Device/dell_apl2x
   SOC := qca9550
   DEVICE_VENDOR := Dell
   DEVICE_MODEL := SonicPoint
-  DEVICE_VARIANT := ACe (APL26-0AE)
   DEVICE_ALT0_VENDOR := SonicWall
   DEVICE_ALT0_MODEL := SonicPoint
-  DEVICE_ALT0_VARIANT := ACe (APL26-0AE)
   DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct kmod-usb2
   KERNEL_SIZE := 5952k
   IMAGE_SIZE := 31680k
   IMAGE/sysupgrade.bin = append-kernel | pad-to $$$$(BLOCKSIZE) | \
 	append-rootfs | pad-rootfs | check-size | append-metadata
 endef
+
+define Device/dell_apl26-0ae
+  $(Device/dell_apl2x)
+  DEVICE_VARIANT := ACe (APL26-0AE)
+  DEVICE_ALT0_VARIANT := ACe (APL26-0AE)
+endef
 TARGET_DEVICES += dell_apl26-0ae
 
+define Device/dell_apl27-0b1
+  $(Device/dell_apl2x)
+  DEVICE_VARIANT := ACi (APL27-0B1)
+  DEVICE_ALT0_VARIANT := ACi (APL27-0B1)
+  DEVICE_PACKAGES += kmod-regulator-userspace-consumer
+endef
+TARGET_DEVICES += dell_apl27-0b1
+
 define Device/devolo_dlan-pro-1200plus-ac
   SOC := ar9344
   DEVICE_VENDOR := devolo




More information about the lede-commits mailing list