[openwrt/openwrt] ramips: add support for TP-Link EX220 v2

LEDE Commits lede-commits at lists.infradead.org
Sat Jul 12 12:38:36 PDT 2025


hauke pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/dd15117dab568c7ebeaa8d3963f041bd8747e4ab

commit dd15117dab568c7ebeaa8d3963f041bd8747e4ab
Author: Gustavo Curi <gpcuri at land.ufrj.br>
AuthorDate: Fri Jun 6 17:13:08 2025 -0300

    ramips: add support for TP-Link EX220 v2
    
    This device is similar to the TP-Link EX220 v1.
    The differences are the number of ports (3 LANs
    and 1 WAN) and the number of LEDs (1 LED RGB)
    
    Hardware
    --------
    
    CPU:    MediaTek MT7621 DAT
    RAM:    128MB DDR3 (integrated)
    FLASH:  16MB SPI-NOR
    WiFi:   MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax
    SERIAL: 115200 8N1
            LED - (TX - RX - GND - 3V3 ) - ETH ports
    
    Installation
    ------------
    
    Flashing is only possible via a serial connection using the sysupgrade
    image; the factory image must be signed. You can flash the sysupgrade
    image directly through the U-Boot console, or preferably, by booting the
    initramfs image and flashing with the sysupgrade command. Follow these
    steps for sysupgrade flashing:
    
    1. Establish a UART serial connection.
    2. Set up a TFTP server at 192.168.0.2 and copy the initramfs image
       there.
    3. Power on the device and press any key to interrupt normal boot.
    4. Load the initramfs image using tftpboot.
    5. Boot with bootm.
    6. If you haven't done so already, back up all stock mtd partitions.
    7. Copy the sysupgrade image to the router.
    8. Flash OpenWrt through either LuCI or the sysupgrade command. Remember
       not to attempt saving settings.
    
    Revert to stock firmware
    ------------------------
    
    Flash stock firmware via OEM web-recovery mode. If you don't have access
    to the stock firmware image, you will need to restore the firmware
    partition backed up earlier.
    
    Web-Recovery
    ------------
    
    The router supports an HTTP recovery mode:
    
    1. Turn off the router.
    2. Press the reset button and power on the device.
    3. When the LED start flashing, release reset and quickly press it
       again.
    
    The interface is reachable at 192.168.0.1 and supports installation of
    the OEM factory image. Note that flashing OpenWrt this way is not
    possible, as mentioned above.
    
    Signed-off-by: Gustavo Curi <gpcuri at land.ufrj.br>
    Link: https://github.com/openwrt/openwrt/pull/19104
    Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
---
 target/linux/ramips/dts/mt7621_tplink_ex220-v2.dts | 230 +++++++++++++++++++++
 target/linux/ramips/image/mt7621.mk                |  14 ++
 2 files changed, 244 insertions(+)

diff --git a/target/linux/ramips/dts/mt7621_tplink_ex220-v2.dts b/target/linux/ramips/dts/mt7621_tplink_ex220-v2.dts
new file mode 100644
index 0000000000..d862d2744c
--- /dev/null
+++ b/target/linux/ramips/dts/mt7621_tplink_ex220-v2.dts
@@ -0,0 +1,230 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	compatible = "tplink,ex220-v2", "mediatek,mt7621-soc";
+	model = "TP-Link EX220 v2";
+
+	aliases {
+		led-boot = &power_led;
+	        led-failsafe = &status_led;
+	        led-upgrade = &power_led;
+	        led-running = &wan_led;
+	        label-mac-device = &gmac0;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		button-wps {
+			label = "rfkill";
+			gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RFKILL>;
+		};
+
+		button-reset {
+			label = "reset";
+			gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		wan_led: led-wan {
+			function = LED_FUNCTION_WAN;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "netdev";
+		};
+
+		status_led: led-status {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		power_led: led-power {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&spi0 {
+	status = "okay";
+
+	flash at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition at 0 {
+				label = "boot";
+				reg = <0x00 0x30000>;
+				read-only;
+			};
+
+			partition at 30000 {
+				label = "boot-env";
+				reg = <0x30000 0x10000>;
+				read-only;
+			};
+
+			partition at 40000 {
+				label = "factory";
+				reg = <0x40000 0x10000>;
+				read-only;
+			};
+
+			partition at 50000 {
+				label = "config";
+				reg = <0x50000 0x10000>;
+				read-only;
+			};
+
+			partition at 60000 {
+				label = "isp_config";
+				reg = <0x60000 0x10000>;
+				read-only;
+			};
+
+			partition at 70000 {
+				label = "rom_file";
+				reg = <0x70000 0x10000>;
+				read-only;
+
+				nvmem-layout {
+					compatible = "fixed-layout";
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					macaddr_rom_file_f100: macaddr at f100 {
+						compatible = "mac-base";
+						reg = <0xf100 0x6>;
+						#nvmem-cell-cells = <1>;
+					};
+				};
+			};
+
+			partition at 80000 {
+				label = "cloud";
+				reg = <0x80000 0x10000>;
+				read-only;
+			};
+
+			partition at 90000 {
+				label = "radio";
+				reg = <0x90000 0x20000>;
+				read-only;
+
+				nvmem-layout {
+					compatible = "fixed-layout";
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					eeprom_radio_0: eeprom at 0 {
+						reg = <0x0 0xe00>;
+					};
+
+					precal_radio_e10: precal at e10 {
+						reg = <0xe10 0x19c10>;
+					};
+				};
+			};
+
+			partition at b0000 {
+				label = "config_bak";
+				reg = <0xb0000 0x10000>;
+				read-only;
+			};
+
+			partition at c0000 {
+				compatible = "denx,fit";
+				label = "firmware";
+				reg = <0xc0000 0xf30000>;
+			};
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&pcie1 {
+	wifi at 0,0 {
+		compatible = "mediatek,mt76";
+		reg = <0x0000 0 0 0 0>;
+		nvmem-cells = <&eeprom_radio_0>, <&precal_radio_e10>, <&macaddr_rom_file_f100 0>;
+		nvmem-cell-names = "eeprom", "precal", "mac-address";
+		mediatek,disable-radar-background;
+
+		band at 1 { 
+			reg = <1>;
+			nvmem-cells = <&macaddr_rom_file_f100 2>;
+			nvmem-cell-names = "mac-address";
+		};
+	};
+};
+
+&gmac0 {
+	nvmem-cells = <&macaddr_rom_file_f100 0>;
+	nvmem-cell-names = "mac-address";
+};
+
+&gmac1 {
+	status = "okay";
+	label = "wan";
+	phy-handle = <&ethphy0>;
+
+	nvmem-cells = <&macaddr_rom_file_f100 1>;
+	nvmem-cell-names = "mac-address";
+};
+
+&ethphy0 {
+	/delete-property/ interrupts;
+};
+
+&switch0 {
+	ports {
+		port at 2 {
+			status = "okay";
+			label = "lan1";
+		};
+
+		port at 3 {
+			status = "okay";
+			label = "lan2";
+		};
+
+		port at 4 {
+			status = "okay";
+			label = "lan3";
+		};
+	};
+};
+
+&state_default {
+	gpio {
+		groups = "i2c", "uart3", "jtag", "wdt";
+		function = "gpio";
+	};
+};
diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk
index 941c4d3e7e..07c68944ed 100644
--- a/target/linux/ramips/image/mt7621.mk
+++ b/target/linux/ramips/image/mt7621.mk
@@ -2885,6 +2885,20 @@ define Device/tplink_ex220-v1
 endef
 TARGET_DEVICES += tplink_ex220-v1
 
+define Device/tplink_ex220-v2
+  $(Device/dsa-migration)
+  DEVICE_VENDOR := TP-Link
+  DEVICE_MODEL := EX220
+  DEVICE_VARIANT := v2
+  DEVICE_PACKAGES := kmod-mt7915-firmware -uboot-envtools
+  TPLINK_BOARD_ID := EX220-V2
+  KERNEL_LOADADDR := 0x82000000
+  KERNEL := kernel-bin | relocate-kernel $(loadaddr-y) | lzma | \
+	fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
+  IMAGE_SIZE := 15744k
+endef
+TARGET_DEVICES += tplink_ex220-v2
+
 define Device/tplink_mr600-v2-eu
   $(Device/dsa-migration)
   $(Device/tplink-v2)




More information about the lede-commits mailing list