[openwrt/openwrt] mvebu: Add support for WD Cloud Mirror Gen2
LEDE Commits
lede-commits at lists.infradead.org
Sun Jan 12 10:53:14 PST 2025
hauke pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/8fb805aa1f25b69b7849c8b1ce787ed47b16d123
commit 8fb805aa1f25b69b7849c8b1ce787ed47b16d123
Author: Robert Senderek <robert.senderek at 10g.pl>
AuthorDate: Fri Nov 22 00:05:39 2024 +0100
mvebu: Add support for WD Cloud Mirror Gen2
Hardware
--------
Marvell Armada 385 (MV88F6820)
512B RAM
256MB NAND (Hynix H27U2G8F2CTR)
1x 1Gbit
2x USB 3.0
2x SATA-III
UART: 115200 8N1 3.3V
RTC
Weltrend MCU WT6703F connected via UART1 for Power LED / PWM Fan / hw reset / WoL
Installation
------------
Connect UART 3.3V adapter to JP2 pins: 1-RX / 2-GND / 5-TX
Use USB2.0 FAT32 pendrive with openwrt-mvebu-cortexa9-wd_cloud-mirror-gen2-initramfs-kernel.bin
1. stop boot by pressing 1
2. usb start
3. fatload usb 0:1 0x02000000 openwrt-mvebu-cortexa9-wd_cloud-mirror-gen2-initramfs-kernel.bin;bootm 0x02000000 -
4. do backup mtd1 mtd3
5. use sysupgrade
Or tftp
1. stop boot by pressing 1
2. setenv ethact egiga2;setenv serverip 192.168.11.114;setenv ipaddr 192.168.11.113
3. tftpboot 0x02000000 openwrt-mvebu-cortexa9-wd_cloud-mirror-gen2-initramfs-kernel.bin; bootm 0x02000000 -
4. do backup mtd1 mtd3
5. use sysupgrade
or Evgeny Kolesnikov <evgenyz at gmail.com> method from his failed PR 2040
- Using original firmware's network settings obtain SSH access to the device.
- Put *-image-cfs-factory.bin and *-uImage-factory.bin images into device's /tmp directory.
- Write kernel (uImage) image 'flash_eraseall /dev/mtd1 && nandwrite --markbad -p /dev/mtd1 /tmp/*-uImage-factory.bin'.
- Write rootfs (image-cfs) image 'ubiformat /dev/mtd3 -f /tmp/*-image.cfs-factory.bin -y'.
- Reboot the device.
Installation (upgrade):
Use *-sysupgrade.bin in a usual way.
Weltrend MCU control is done via uart1 19200
stty -F /dev/ttyS1 raw speed 19200
stty -F /dev/ttyS1 raw speed 19200
PWM Fan Control
off: 00
echo -n -e '\xfa\x02\x00\x00\x00\x00\xfb' > /dev/ttyS1
slow: 5F
echo -n -e '\xfa\x02\x00\x5f\x00\x00\xfb' > /dev/ttyS1
max: FF
echo -n -e '\xfa\x02\x00\xff\x00\x00\xfb' > /dev/ttyS1
Power LED Control
Blue
echo -n -e '\xfa\x26\x00\x11\x00\x01\xfb' > /dev/ttyS1
Red
echo -n -e '\xfa\x26\x00\x14\x00\x01\xfb' > /dev/ttyS1
Orange
echo -n -e '\xfa\x26\x00\x12\x00\x01\xfb' > /dev/ttyS1
more here: https://github.com/c-MM/mcm-daemon/blob/master/mcm.h
Signed-off-by: Robert Senderek <robert.senderek at 10g.pl>
Link: https://github.com/openwrt/openwrt/pull/17046
Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
---
.../cortexa9/base-files/etc/board.d/02_network | 9 +-
.../cortexa9/base-files/lib/upgrade/platform.sh | 3 +-
.../marvell/armada-385-wd_cloud-mirror-gen2.dts | 368 +++++++++++++++++++++
target/linux/mvebu/image/cortexa9.mk | 17 +
4 files changed, 395 insertions(+), 2 deletions(-)
diff --git a/target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network b/target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network
index 680af1ce67..8cf1c0e426 100644
--- a/target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network
+++ b/target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network
@@ -13,7 +13,8 @@ mvebu_setup_interfaces()
case "$board" in
ctera,c200-v2|\
- synology,ds213j)
+ synology,ds213j|\
+ wd,cloud-mirror-gen2)
ucidef_set_interface_lan "eth0" "dhcp"
;;
cznic,turris-omnia)
@@ -94,6 +95,12 @@ mvebu_setup_macs()
lan_mac=$label_mac
wan_mac=$label_mac
;;
+ wd,cloud-mirror-gen2)
+ # mac address is on ubi "config" or ubi "reserve2" in text file.
+ # ubi "reserve2" /dev/mtd7 is twice small and only contains basic OEM factory info
+ label_mac=$(macaddr_canonicalize $(strings /dev/mtd7|grep -E '([0-9A-F]{2}[:])'))
+ lan_mac=$label_mac
+ ;;
esac
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
diff --git a/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh b/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh
index 70678622d3..13d8e77c93 100755
--- a/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh
+++ b/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh
@@ -31,7 +31,8 @@ platform_do_upgrade() {
CI_ROOT_UBIPART=ubi
nand_do_upgrade "$1"
;;
- buffalo,ls421de)
+ buffalo,ls421de|\
+ wd,cloud-mirror-gen2)
nand_do_upgrade "$1"
;;
ctera,c200-v2)
diff --git a/target/linux/mvebu/files-6.6/arch/arm/boot/dts/marvell/armada-385-wd_cloud-mirror-gen2.dts b/target/linux/mvebu/files-6.6/arch/arm/boot/dts/marvell/armada-385-wd_cloud-mirror-gen2.dts
new file mode 100644
index 0000000000..50936e72ad
--- /dev/null
+++ b/target/linux/mvebu/files-6.6/arch/arm/boot/dts/marvell/armada-385-wd_cloud-mirror-gen2.dts
@@ -0,0 +1,368 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for Western Digital My Cloud Mirror Gen 2
+ * (BWVZ/Grand Teton)
+ *
+ * Copyright (C) 2020
+ *
+ * Based on the code from:
+ *
+ * Copyright (C) 2019 Evgeny Kolesnikov <evgenyz at gmail.com>
+ * Copyright (C) 2016 Martin Mueller <mm at sig21.net>
+ * Copyright (C) 2013 Gregory CLEMENT <gregory.clement at free-electrons.com>
+ * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
+ *
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "armada-385.dtsi"
+
+/ {
+ model = "WD MyCloud Mirror Gen 2 (BWVZ/Grand Teton)";
+ compatible = "wd,cloud-mirror-gen2", "marvell,armada385", "marvell,armada380";
+
+ aliases {
+ led-boot = &led_boot;
+ led-failsafe = &led_boot;
+ led-upgrade = &led_boot;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ append-rootblock = "nullparameter="; /* override the bootloader args */
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>; /* 512 MB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
+ MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
+ MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
+ MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
+
+ internal-regs {
+ timer at c200 {
+ status = "okay";
+ };
+
+ i2c0: i2c at 11000 {
+ status = "okay";
+ clock-frequency = <100000>;
+ };
+
+ i2c1: i2c at 11100 {
+ status = "okay";
+ clock-frequency = <100000>;
+ };
+
+ serial at 12000 {
+ status = "okay";
+ };
+
+ /* Connected to Welltrend 6703F-OG240WT MCU
+ * which controls power, fan and other things
+ */
+ serial at 12100 {
+ status = "okay";
+ };
+
+ pinctrl at 18000 {
+ /* use only one pin for UART1, as mpp20 is used by sata0 */
+ uart1_pins: uart-pins-1 {
+ marvell,pins = "mpp19";
+ marvell,function = "ua1";
+ };
+
+ xhci0_vbus_pins: xhci0-vbus-pins {
+ marvell,pins = "mpp26";
+ marvell,function = "gpio";
+ };
+
+ xhci1_vbus_pins: xhci1-vbus-pins {
+ marvell,pins = "mpp27";
+ marvell,function = "gpio";
+ };
+
+ sata0_pins: sata-pins-0 {
+ marvell,pins = "mpp55";
+ marvell,function = "sata0";
+ };
+
+ sata1_pins: sata-pins-1 {
+ marvell,pins = "mpp56";
+ marvell,function = "sata1";
+ };
+
+ sata_leds: sata-leds {
+ marvell,pins = "mpp43", "mpp52", "mpp53", "mpp54";
+ marvell,function = "gpio";
+ };
+
+ btn_pins: btn-pins {
+ marvell,pins = "mpp50";
+ marvell,function = "gpio";
+ };
+ };
+
+ usb at 58000 {
+ status = "okay";
+ };
+
+ phy: mdio at 72004 {
+ phy0: ethernet-phy at 0 {
+ /* Init ETH LEDs */
+ marvell,reg-init = <3 16 0 0x101e>;
+ reg = <0>;
+ };
+ };
+
+ sata at a8000 {
+ status = "okay";
+ };
+
+ nand-controller at d0000 {
+ status = "okay";
+
+ nand: nand at 0 {
+ reg = <0>;
+ label = "pxa3xx_nand-0";
+ nand-rb = <0>;
+ marvell,nand-keep-config;
+ #marvell,nand-enable-arbiter; //optional
+ nand-on-flash-bbt;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 00000000 {
+ label = "U-Boot";
+ reg = <0x00000000 0x00500000>; /* 5 MB */
+ read-only;
+ };
+
+ partition at 00500000 {
+ label = "kernel";
+ reg = <0x00500000 0x00500000>; /* 5 MB */
+ };
+
+ partition at 00a00000 {
+ label = "uRamdisk";
+ reg = <0x00a00000 0x00500000>; /* 5 MB */
+ read-only;
+ };
+
+ partition at 00f00000 {
+ label = "ubi";
+ reg = <0x00f00000 0x0b900000>; /* 185 MB */
+ };
+
+ partition at c800000 {
+ label = "rescue fw";
+ reg = <0x0c800000 0x00f00000>; /* 15 MB */
+ read-only;
+ };
+
+ partition at d70000 {
+ label = "config";
+ reg = <0x0d700000 0x01400000>; /* 20 MB */
+ read-only;
+ };
+
+ partition at eb00000 {
+ label = "reserve1";
+ reg = <0x0eb00000 0x00a00000>; /* 10 MB */
+ read-only;
+ };
+
+ partition at f500000 {
+ label = "reserve2";
+ reg = <0x0f500000 0x00a00000>; /* 10 MB */
+ read-only;
+ };
+ };
+ };
+ };
+
+ usb3 at f0000 {
+ usb-phy = <&usb3_0_phy>;
+ status = "okay";
+ };
+
+ usb3 at f8000 {
+ usb-phy = <&usb3_1_phy>;
+ status = "okay";
+ };
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&sata_leds>;
+
+ led_boot: s1red {
+ label = "red:hdd1";
+ gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
+ };
+ s2red {
+ label = "red:hdd2";
+ gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
+ };
+ s1blue {
+ label = "blue:hdd1";
+ gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "ata1";
+ };
+ s2blue {
+ label = "blue:hdd2";
+ gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "ata2";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&btn_pins>;
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>; // Restart=0x198, Power=0x116
+ gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ wakeup-source;
+ };
+ };
+
+ usb3_0_phy: usb3_0_phy {
+ compatible = "usb-nop-xceiv";
+ vcc-supply = <®_usb3_0_vbus>;
+ };
+
+ usb3_1_phy: usb3_1_phy {
+ compatible = "usb-nop-xceiv";
+ vcc-supply = <®_usb3_1_vbus>;
+ };
+
+ reg_usb3_0_vbus: usb3-vbus0 {
+ compatible = "regulator-fixed";
+ regulator-name = "usb3-vbus0";
+ pinctrl-names = "default";
+ pinctrl-0 = <&xhci0_vbus_pins>;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ gpio = <&gpio0 26 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_usb3_1_vbus: usb3-vbus1 {
+ compatible = "regulator-fixed";
+ regulator-name = "usb3-vbus1";
+ pinctrl-names = "default";
+ pinctrl-0 = <&xhci1_vbus_pins>;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ gpio = <&gpio0 27 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_sata0: pwr-sata0 {
+ compatible = "regulator-fixed";
+ regulator-name = "pwr_en_sata0";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ enable-active-high;
+ regulator-boot-on;
+ gpio = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_5v_sata0: v5-sata0 {
+ compatible = "regulator-fixed";
+ regulator-name = "v5.0-sata0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <®_sata0>;
+ };
+
+ reg_12v_sata0: v12-sata0 {
+ compatible = "regulator-fixed";
+ regulator-name = "v12.0-sata0";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ vin-supply = <®_sata0>;
+ };
+
+ reg_sata1: pwr-sata1 {
+ compatible = "regulator-fixed";
+ regulator-name = "pwr_en_sata1";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ enable-active-high;
+ regulator-boot-on;
+ gpio = <&gpio1 24 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_5v_sata1: v5-sata1 {
+ compatible = "regulator-fixed";
+ regulator-name = "v5.0-sata1";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <®_sata1>;
+ };
+
+ reg_12v_sata1: v12-sata1 {
+ compatible = "regulator-fixed";
+ regulator-name = "v12.0-sata1";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ vin-supply = <®_sata1>;
+ };
+};
+
+&bm {
+ status = "okay";
+};
+
+&bm_bppi {
+ status = "okay";
+};
+
+ð2 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "sgmii";
+ buffer-manager = <&bm>;
+ bm,pool-long = <0>;
+ bm,pool-short = <1>;
+};
+
+&ahci0 {
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sata-port at 0 {
+ reg = <0>;
+ target-supply = <®_sata0>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ sata-port at 1 {
+ reg = <1>;
+ target-supply = <®_sata1>;
+ #thermal-sensor-cells = <1>;
+ };
+};
diff --git a/target/linux/mvebu/image/cortexa9.mk b/target/linux/mvebu/image/cortexa9.mk
index 4a41f2c102..d572264866 100644
--- a/target/linux/mvebu/image/cortexa9.mk
+++ b/target/linux/mvebu/image/cortexa9.mk
@@ -448,3 +448,20 @@ define Device/synology_ds213j
-ppp -kmod-nft-offload -dnsmasq -odhcpd-ipv6only
endef
TARGET_DEVICES += synology_ds213j
+
+define Device/wd_cloud-mirror-gen2
+ $(Device/NAND-128K)
+ DEVICE_VENDOR := Western Digital
+ DEVICE_MODEL := MyCloud Mirror Gen 2 (BWVZ/Grand Teton)
+ DEVICE_PACKAGES += -uboot-envtools coreutils-stty mkf2fs e2fsprogs \
+ partx-utils kmod-hwmon-drivetemp -ppp -kmod-nft-offload -dnsmasq \
+ -odhcpd-ipv6only
+ DEVICE_DTS := armada-385-wd_cloud-mirror-gen2
+ KERNEL_SIZE := 5120k
+ KERNEL := kernel-bin | append-dtb | uImage none
+ KERNEL_INITRAMFS := kernel-bin | append-dtb | uImage none
+ IMAGES += image-cfs-factory.bin uImage-factory.bin
+ IMAGE/image-cfs-factory.bin := append-ubi
+ IMAGE/uImage-factory.bin := append-kernel
+endef
+TARGET_DEVICES += wd_cloud-mirror-gen2
More information about the lede-commits
mailing list