[openwrt/openwrt] mediatek: filogic: Add support for cudy wr3000h
LEDE Commits
lede-commits at lists.infradead.org
Sun Jan 12 08:09:25 PST 2025
hauke pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/9d66b8b312fb6a4087244ee3ee10e1ba1623df81
commit 9d66b8b312fb6a4087244ee3ee10e1ba1623df81
Author: Juan Pedro Paredes Caballero <juanpedro.paredes at gmail.com>
AuthorDate: Sat Dec 7 14:20:31 2024 +0100
mediatek: filogic: Add support for cudy wr3000h
The manufacturer Cudy usually releases signed openwrt firmware, to
facilitate the migration from the proprietary version to the official
versions of openwrt. In contact with the manufacturer tells me that only
releases the firmware of the WR3000H if and only if
there is an official version. With this proposal I pretend to have an
initial operative version so that they do their part, and facilitate to
the users the possibility of using openwrt. In the present state, it is
only possible to use this firmware by uploading and installing it with
UART connection.
AX3000 2.5G Dual Band Wi-Fi 6 Mesh Router (WR3000H)
Hardware
--------
MediaTek MT7981 WiSoC
256MB DDR3 RAM
128MB SPI-NAND (XMC XM25QH128C)
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
4 LAN MediaTek MT7531 PHY
1 WAN RTL8221B-VB-CG 2.5Gbps PHY (C22)
2 Radios MT7976CN
UART: 115200 8N1 3.3V
MAC:
LAN MAC: label mac
WAN MAC: label mac + 1
2.4G MAC: label mac
5G MAC: label mac + 1 with LA bit set
Installation
------------
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device + press reset pin. Keep pressing reset pin to
enter the U-Boot shell (The recovery.bin image load process must fail).
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.88. Rename the image to "cudy3000h.bin"
4. Download and boot the OpenWrt initramfs image.
$ tftpboot 0x46000000 cudy3000h.bin; bootm 0x46000000
5. IMPORTANT: Make backup from original firmware. System -> Backup
/Flash Firmware -> Save mtdblock contents. All mtdblock one by one,
keep unaltered (BL2, u-boot-env, Factory, bdinfo, FIP, and ubi).
6. Transfer the OpenWrt sysupgrade image to the device using scp.
Install with sysupgrade.
Warning for BL2 and U-BOOT developers
-------------------------------------
The nand partition layout from vendor is slightly diferent from "standard".
The FIP partition starts at 0x3c0000 be carefull with BL2 to BL31.
The UBI partition start at 0x5c0000 be carefull.
DO NOT OVERWRITE bdinfo partition it contains hardware MAC definition
Layout is start-end (not start size)
- 0x000000000000-0x000007800000 : "nmbm0"
- 0x000000000000-0x000000100000 : "bl2"
- 0x000000100000-0x000000180000 : "u-boot-env"
- 0x000000180000-0x000000380000 : "factory"
- 0x000000380000-0x0000003c0000 : "bdinfo"
- 0x0000003c0000-0x0000005c0000 : "fip"
- 0x0000005c0000-0x0000045c0000 : "ubi"
ALLWAYS for U-BOOT operations check this
setenv mtdids nmbm0=nmbm0
setenv mtdparts nmbm0:1024k(bl2),512k(u-boot-env),2048k(factory),256k(bdinfo),2048k(fip),65536k(ubi)
Signed-off-by: Juan Pedro Paredes Caballero <juanpedro.paredes at gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17458
Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
---
.../linux/mediatek/dts/mt7981b-cudy-wr3000h-v1.dts | 337 +++++++++++++++++++++
.../filogic/base-files/etc/board.d/01_leds | 8 +
.../etc/hotplug.d/ieee80211/11_fix_wifi_mac | 1 +
.../filogic/base-files/lib/upgrade/platform.sh | 4 +
target/linux/mediatek/image/filogic.mk | 17 ++
5 files changed, 367 insertions(+)
diff --git a/target/linux/mediatek/dts/mt7981b-cudy-wr3000h-v1.dts b/target/linux/mediatek/dts/mt7981b-cudy-wr3000h-v1.dts
new file mode 100644
index 0000000000..0808eb9557
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7981b-cudy-wr3000h-v1.dts
@@ -0,0 +1,337 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+
+#include "mt7981.dtsi"
+
+/ {
+ model = "Cudy WR3000H v1";
+ compatible = "cudy,wr3000h-v1", "mediatek,mt7981-spim-snand-rfb";
+
+ aliases {
+ label-mac-device = &gmac0;
+ led-boot = &led_status;
+ led-failsafe = &led_status;
+ led-running = &led_status;
+ led-upgrade = &led_status;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&pio 1 GPIO_ACTIVE_LOW>;
+ };
+
+ wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&pio 0 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-export {
+ compatible = "gpio-export";
+ #size-cells = <0>;
+
+ phyreset {
+ gpio-export,name = "phyreset";
+ gpio-export,output = <1>;
+ gpios = <&pio 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_status: led at 0 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 5 GPIO_ACTIVE_LOW>;
+ };
+
+
+ led_internet {
+ function = LED_FUNCTION_WAN_ONLINE;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 11 GPIO_ACTIVE_LOW>;
+ };
+
+ led_wps {
+ function = LED_FUNCTION_WPS;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+ };
+
+ led_wlan2g {
+ function = LED_FUNCTION_WLAN_2GHZ;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 6 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ led_wlan5g {
+ function = LED_FUNCTION_WLAN_5GHZ;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 7 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ led_lan1 {
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <1>;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 8 GPIO_ACTIVE_LOW>;
+ };
+
+ led_lan2 {
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <2>;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+ };
+
+ led_lan3 {
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <3>;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 12 GPIO_ACTIVE_LOW>;
+ };
+
+ led_lan4 {
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <4>;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 13 GPIO_ACTIVE_LOW>;
+ };
+
+ led_wan {
+ function = LED_FUNCTION_WAN;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 35 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+ð {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio_pins>;
+
+ status = "okay";
+
+ gmac0: mac at 0 {
+ compatible = "mediatek,eth-mac";
+ reg = <0>;
+ phy-mode = "2500base-x";
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&macaddr_bdinfo_de00 0>;
+ label = "lan";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+
+ gmac1: mac at 1 {
+ compatible = "mediatek,eth-mac";
+ reg = <1>;
+ phy-mode = "2500base-x";
+ phy-handle = <&phy6>;
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&macaddr_bdinfo_de00 1>;
+ label = "wan";
+ };
+
+};
+
+&mdio_bus {
+ switch: switch at 1f {
+ compatible = "mediatek,mt7531";
+ reg = <31>;
+ reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&pio>;
+ interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ phy6: ethernet-phy at 6 {
+ compatible = "ethernet-phy-ieee802.3-c22"; // [RTL8221B-VB-CG 2.5Gbps PHY (C22)]
+ reg = <6>;
+ phy-mode = "2500base-x";
+ };
+
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_flash_pins>;
+ status = "okay";
+
+ spi_nand: flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-nand";
+ reg = <0>;
+ spi-max-frequency = <52000000>;
+
+ spi-cal-enable;
+ spi-cal-mode = "read-data";
+ spi-cal-datalen = <7>;
+ spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>;
+ spi-cal-addrlen = <5>;
+ spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;
+
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+ mediatek,nmbm;
+ mediatek,bmt-max-ratio = <1>;
+ mediatek,bmt-max-reserved-blocks = <64>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "BL2";
+ reg = <0x00000 0x0100000>;
+ read-only;
+ };
+
+ partition at 100000 {
+ label = "u-boot-env";
+ reg = <0x0100000 0x0080000>;
+ read-only;
+ };
+
+ factory: partition at 180000 {
+ label = "Factory";
+ reg = <0x180000 0x0200000>;
+ read-only;
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ eeprom_factory_0: eeprom at 0 {
+ reg = <0x0 0x1000>;
+ };
+ };
+ };
+
+ partition at 380000 {
+ label = "bdinfo";
+ reg = <0x380000 0x0040000>;
+ read-only;
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_bdinfo_de00: macaddr at de00 {
+ compatible = "mac-base";
+ reg = <0xde00 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+ };
+ };
+
+ partition at 3C0000 {
+ label = "FIP";
+ reg = <0x3C0000 0x0200000>;
+ read-only;
+ };
+
+ partition at 580000 {
+ label = "ubi";
+ reg = <0x5C0000 0x4000000>;
+ compatible = "linux,ubi";
+ };
+ };
+ };
+};
+
+&pio {
+ spi0_flash_pins: spi0-pins {
+ mux {
+ function = "spi";
+ groups = "spi0", "spi0_wp_hold";
+ };
+ conf-pu {
+ pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
+ };
+
+ conf-pd {
+ pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
+ };
+ };
+};
+
+&switch {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ label = "lan1";
+ };
+
+ port at 1 {
+ reg = <1>;
+ label = "lan2";
+ };
+
+ port at 2 {
+ reg = <2>;
+ label = "lan3";
+ };
+
+ port at 3 {
+ reg = <3>;
+ label = "lan4";
+ };
+
+ port at 6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+};
+
+&wifi {
+ status = "okay";
+ nvmem-cells = <&eeprom_factory_0>;
+ nvmem-cell-names = "eeprom";
+};
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
index ca4961c655..a6bb9b0ca8 100644
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
@@ -38,6 +38,14 @@ cudy,re3000-v1)
cudy,wr3000-v1)
ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan"
;;
+cudy,wr3000h-v1)
+ ucidef_set_led_netdev "lan1" "lan1" "white:lan-1" "lan1" "link tx rx"
+ ucidef_set_led_netdev "lan2" "lan2" "white:lan-2" "lan2" "link tx rx"
+ ucidef_set_led_netdev "lan3" "lan3" "white:lan-3" "lan3" "link tx rx"
+ ucidef_set_led_netdev "lan4" "lan4" "white:lan-4" "lan4" "link tx rx"
+ ucidef_set_led_netdev "wan" "wan" "white:wan" "wan" "link tx rx"
+ ucidef_set_led_netdev "internet" "internet" "white:wan-online" "wan" "link"
+ ;;
glinet,gl-x3000|\
glinet,gl-xe3000)
ucidef_set_led_default "power" "POWER" "green:power" "1"
diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
index 3188fe71d5..4ae2c70658 100644
--- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
+++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
@@ -79,6 +79,7 @@ case "$board" in
cudy,re3000-v1|\
cudy,tr3000-v1|\
cudy,wr3000s-v1|\
+ cudy,wr3000h-v1|\
cudy,wr3000-v1)
addr=$(mtd_get_mac_binary bdinfo 0xde00)
# Originally, phy0 is phy1 mac with LA bit set. However, this would conflict
diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
index 7556be52bd..1d89640a4e 100755
--- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
+++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
@@ -118,6 +118,10 @@ platform_do_upgrade() {
CI_KERNPART="linux"
nand_do_upgrade "$1"
;;
+ cudy,wr3000h-v1)
+ CI_UBIPART="ubi"
+ nand_do_upgrade "$1"
+ ;;
cudy,re3000-v1|\
cudy,wr3000-v1|\
yuncore,ax835)
diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk
index 22c9151ff3..afa5224b19 100644
--- a/target/linux/mediatek/image/filogic.mk
+++ b/target/linux/mediatek/image/filogic.mk
@@ -705,6 +705,23 @@ define Device/cudy_wr3000s-v1
endef
TARGET_DEVICES += cudy_wr3000s-v1
+define Device/cudy_wr3000h-v1
+ DEVICE_VENDOR := Cudy
+ DEVICE_MODEL := WR3000H
+ DEVICE_VARIANT := v1
+ DEVICE_DTS := mt7981b-cudy-wr3000h-v1
+ DEVICE_DTS_DIR := ../dts
+ SUPPORTED_DEVICES += R59
+ UBINIZE_OPTS := -E 5
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ IMAGE_SIZE := 65536k
+ KERNEL_IN_UBI := 1
+ IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+ DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware
+endef
+TARGET_DEVICES += cudy_wr3000h-v1
+
define Device/dlink_aquila-pro-ai-m30-a1
DEVICE_VENDOR := D-Link
DEVICE_MODEL := AQUILA PRO AI M30
More information about the lede-commits
mailing list