[openwrt/openwrt] ramips: Add support for TP-Link Archer MR200 v6
LEDE Commits
lede-commits at lists.infradead.org
Sat Jan 11 13:23:10 PST 2025
hauke pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/9c8ac97e70fdad528387d203571176b9328f94ef
commit 9c8ac97e70fdad528387d203571176b9328f94ef
Author: Damien Zammit <damien at zamaudio.com>
AuthorDate: Sun May 26 16:40:51 2024 +1000
ramips: Add support for TP-Link Archer MR200 v6
This adds a new port for the above device.
Currently, there is no easy installation method except
opening the device up and soldering a UART header on and
getting u-boot shell access. You boot the initramfs version
first using tftpboot, then once booted, you sysupgrade.
Shell access to root on vendor firmware:
admin:1234
To get U-Boot console, spam '4' into the serial console at boot.
with LEDs on the left, serial pinout is:
o - tx
o - rx
o - gnd
x - 3v3
server ip for tftpboot
192.168.0.225
The initramfs-kernel version boots without touching onboard flash with:
MT7628# tftpboot 0x80000000 openwrt-ramips-mt76x8-tplink_archer-mr200-v6-initramfs-kernel.bin
MT7628# bootm 0x80000000
Then when it boots off RAM, you copy
openwrt-ramips-mt76x8-tplink_archer-mr200-v6-squashfs-sysupgrade.bin
to /tmp/sysupgrade.bin of the device and run:
root at OpenWrt:/tmp# sysupgrade -n sysupgrade.bin
- [x] LEDs working
- [x] Buttons working
- [x] wlan detected
- [x] wwan detected
- [x] initramfs image working
- [x] sysupgrade working
Signed-off-by: Damien Zammit <damien at zamaudio.com>
Link: https://github.com/openwrt/openwrt/pull/15610
Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
---
.../ramips/dts/mt7628an_tplink_archer-mr200-v6.dts | 192 +++++++++++++++++++++
target/linux/ramips/image/mt76x8.mk | 16 ++
.../ramips/mt76x8/base-files/etc/board.d/01_leds | 3 +-
.../mt76x8/base-files/etc/board.d/02_network | 3 +-
4 files changed, 212 insertions(+), 2 deletions(-)
diff --git a/target/linux/ramips/dts/mt7628an_tplink_archer-mr200-v6.dts b/target/linux/ramips/dts/mt7628an_tplink_archer-mr200-v6.dts
new file mode 100644
index 0000000000..c33b885c7e
--- /dev/null
+++ b/target/linux/ramips/dts/mt7628an_tplink_archer-mr200-v6.dts
@@ -0,0 +1,192 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7628an.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ compatible = "tplink,archer-mr200-v6", "mediatek,mt7628an-soc";
+ model = "TP-Link Archer MR200 v6";
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ label-mac-device = ðernet;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ lan {
+ function = LED_FUNCTION_LAN;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+ };
+
+ wan {
+ function = LED_FUNCTION_WAN;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&gpio 40 GPIO_ACTIVE_LOW>;
+ };
+
+ led_power: power {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&gpio 39 GPIO_ACTIVE_LOW>;
+ };
+
+ signal1 {
+ label = "white:signal1";
+ gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
+ };
+
+ signal2 {
+ label = "white:signal2";
+ gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
+ };
+
+ signal3 {
+ label = "white:signal3";
+ gpios = <&gpio 43 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan {
+ function = LED_FUNCTION_WLAN;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ rfkill {
+ label = "rfkill";
+ gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RFKILL>;
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ m25p,fast-read;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x20000>;
+ read-only;
+ };
+
+ firmware at 20000 {
+ compatible = "tplink,firmware";
+ label = "firmware";
+ reg = <0x20000 0xfa0000>;
+ };
+
+ partition at fc0000 {
+ label = "config";
+ reg = <0xfc0000 0x10000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_config_f100: macaddr at f100 {
+ compatible = "mac-base";
+ reg = <0xf100 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+ };
+ };
+
+ partition at fd0000 {
+ label = "romfile";
+ reg = <0xfd0000 0x10000>;
+ read-only;
+ };
+
+ partition at fe0000 {
+ label = "radio";
+ reg = <0xfe0000 0x10000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ eeprom_radio_0: eeprom at 0 {
+ reg = <0x0 0x400>;
+ };
+
+ eeprom_radio_8000: eeprom at 8000 {
+ reg = <0x8000 0x4da8>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&state_default {
+ gpio {
+ groups = "i2c", "p0led_an", "p1led_an", "p2led_an", "p3led_an", "p4led_an", "uart1", "wdt";
+ function = "gpio";
+ };
+};
+
+&wmac {
+ nvmem-cells = <&eeprom_radio_0>, <&macaddr_config_f100 0>;
+ nvmem-cell-names = "eeprom", "mac-address";
+ status = "okay";
+};
+
+&esw {
+ mediatek,portdisable = <0x30>;
+};
+
+ðernet {
+ nvmem-cells = <&macaddr_config_f100 0>;
+ nvmem-cell-names = "mac-address";
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pcie0 {
+ wifi at 0,0 {
+ reg = <0x0000 0 0 0 0>;
+ ieee80211-freq-limit = <5000000 6000000>;
+ nvmem-cells = <&eeprom_radio_8000>, <&macaddr_config_f100 (-1)>;
+ nvmem-cell-names = "eeprom", "mac-address";
+ };
+};
diff --git a/target/linux/ramips/image/mt76x8.mk b/target/linux/ramips/image/mt76x8.mk
index dbad26a140..76b1951588 100644
--- a/target/linux/ramips/image/mt76x8.mk
+++ b/target/linux/ramips/image/mt76x8.mk
@@ -675,6 +675,22 @@ define Device/tplink_archer-mr200-v5
endef
TARGET_DEVICES += tplink_archer-mr200-v5
+define Device/tplink_archer-mr200-v6
+ $(Device/tplink-v2)
+ IMAGE_SIZE := 15936k
+ DEVICE_MODEL := Archer MR200
+ DEVICE_VARIANT := v6
+ TPLINK_FLASHLAYOUT := 16Mmtk
+ TPLINK_HWID := 0x20000006
+ TPLINK_HWREV := 0x6
+ TPLINK_HWREVADD := 0x6
+ DEVICE_PACKAGES := kmod-mt76x0e uqmi kmod-usb2 kmod-usb-serial-option
+ KERNEL := kernel-bin | append-dtb | lzma -d22
+ KERNEL_INITRAMFS := kernel-bin | append-dtb
+ IMAGES := sysupgrade.bin
+endef
+TARGET_DEVICES += tplink_archer-mr200-v6
+
define Device/tplink_re200-v2
$(Device/tplink-safeloader)
IMAGE_SIZE := 7808k
diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
index fda4fa3bdf..e13c5db50e 100644
--- a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds
@@ -89,7 +89,8 @@ tplink,archer-c50-v6)
ucidef_set_led_wlan "wlan2g" "wlan2g" "green:wlan2g" "phy0tpt"
ucidef_set_led_wlan "wlan5g" "wlan5g" "green:wlan5g" "phy1tpt"
;;
-tplink,archer-mr200-v5)
+tplink,archer-mr200-v5|\
+tplink,archer-mr200-v6)
ucidef_set_led_netdev "lan" "lan" "white:lan" "eth0"
ucidef_set_led_netdev "wan" "wan" "white:wan" "wwan0"
;;
diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
index 10e0e84dde..994ed0009b 100644
--- a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
@@ -166,7 +166,8 @@ ramips_setup_interfaces()
ucidef_add_switch "switch0" \
"0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "6t at eth0"
;;
- tplink,archer-mr200-v5)
+ tplink,archer-mr200-v5|\
+ tplink,archer-mr200-v6)
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "6t at eth0"
ucidef_set_interface "wan" device "/dev/cdc-wdm0" protocol "qmi"
More information about the lede-commits
mailing list