[openwrt/openwrt] qualcommax: ipq807x: add support for Linksys MX4300 (LN1301)
LEDE Commits
lede-commits at lists.infradead.org
Sun Feb 16 04:03:35 PST 2025
robimarko pushed a commit to openwrt/openwrt.git, branch openwrt-24.10:
https://git.openwrt.org/4c9cae19069ef7f03086ff0f180129f720c067b4
commit 4c9cae19069ef7f03086ff0f180129f720c067b4
Author: Paweł Owoc <frut3k7 at gmail.com>
AuthorDate: Fri Jul 26 19:00:57 2024 +0200
qualcommax: ipq807x: add support for Linksys MX4300 (LN1301)
Hardware specification:
========
SoC: Qualcomm IPQ8174
Flash: 1GB (Micron MT29F8G08ABBCAH4 or AMD/Spansion S34MS08G2)
RAM: 2GB (2x Kingston B5116ECMDXGJD or ESMT M15T2G16128A DDR3L)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 5GHz ax 2x2 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 36-64 (low band)
WiFi2: 2.4GHz ax 2x2 (Qualcomm QCN5024 + Skyworks SKY85340-11)
WiFi3: 5GHz ax 4x4 (Qualcomm QCN5054 + Skyworks SKY85755-11) - channels 100-177 (high band)
LED: 1x RGB status (NXP PCA9633)
USB: 1x USB 3.0
Button: WPS, Reset
Flash instructions:
========
1. Manually upgrade firmware using openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin image.
More details can be found here: https://support.linksys.com/kb/article/6564-en/
After first boot check actual partition:
- fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin kernel
and in case of 1:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd21 0 0
- nandwrite -p /dev/mtd21 openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd23 0 0
- nandwrite -p /dev/mtd23 openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin alt_kernel
3. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx4300-initramfs-uImage.itb of=/dev/sdX
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq807x-linksys_mx4300-squashfs-factory.bin alt_kernel
4. Back to the OEM firmware:
- mtd -e kernel -n write FW_MX4300_1.0.4.215382_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MX4300_1.0.4.215382_prod.img alt_kernel
5. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq807x-linksys_mx4300-initramfs-uImage.itb of=/dev/sdX
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
Co-authored-by: Qiyuan Zhang <zhang.github at outlook.com>
Signed-off-by: Paweł Owoc <frut3k7 at gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16070
(cherry picked from commit 4d310b176be9eea162159f2501e650ebbd6605e9)
Signed-off-by: Rafal Boni <rafal.boni at gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17889
Signed-off-by: Robert Marko <robimarko at gmail.com>
---
.../boot/uboot-envtools/files/qualcommax_ipq807x | 5 +
.../arch/arm64/boot/dts/qcom/ipq8174-mx4300.dts | 273 +++++++++++++++++++++
target/linux/qualcommax/image/ipq807x.mk | 11 +
.../ipq807x/base-files/etc/board.d/02_network | 4 +-
.../etc/hotplug.d/firmware/11-ath11k-caldata | 8 +
.../ipq807x/base-files/etc/init.d/bootcount | 1 +
.../ipq807x/base-files/lib/upgrade/platform.sh | 1 +
7 files changed, 302 insertions(+), 1 deletion(-)
diff --git a/package/boot/uboot-envtools/files/qualcommax_ipq807x b/package/boot/uboot-envtools/files/qualcommax_ipq807x
index f5fb07a4db..2d76045c66 100644
--- a/package/boot/uboot-envtools/files/qualcommax_ipq807x
+++ b/package/boot/uboot-envtools/files/qualcommax_ipq807x
@@ -37,6 +37,11 @@ linksys,mx8500)
[ -n "$idx" ] && \
ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" "2"
;;
+linksys,mx4300)
+ idx="$(find_mtd_index u_env)"
+ [ -n "$idx" ] && \
+ ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x40000" "1"
+ ;;
netgear,sxr80|\
netgear,sxs80|\
tplink,eap660hd-v1)
diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8174-mx4300.dts b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8174-mx4300.dts
new file mode 100644
index 0000000000..1477019ab9
--- /dev/null
+++ b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq8174-mx4300.dts
@@ -0,0 +1,273 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include "ipq8174-mx4x00.dtsi"
+
+/ {
+ model = "Linksys MX4300";
+ compatible = "linksys,mx4300", "qcom,ipq8074";
+
+ chosen {
+ /*
+ In the kernel command line, replace the first occurence of bootargs-find-X with bootargs-replace-X.
+ If bootargs-exact-match-X is set to "y", then replacement happens only if the kernel command line
+ is identical to bootargs-find-X.
+ */
+ bootargs-find-1 = "ubi.mtd=22,2048";
+ bootargs-replace-1 = "ubi.mtd=22,4096";
+
+ bootargs-find-2 = "ubi.mtd=24,2048";
+ bootargs-replace-2 = "ubi.mtd=24,4096";
+ };
+};
+
+&qpic_nand {
+ status = "okay";
+
+ /*
+ * Bootloader will find the NAND DT node by the compatible and
+ * then "fixup" it by adding the partitions from the SMEM table
+ * using the legacy bindings thus making it impossible for us
+ * to change the partition table or utilize NVMEM for calibration.
+ * So add a dummy partitions node that bootloader will populate
+ * and set it as disabled so the kernel ignores it instead of
+ * printing warnings due to the broken way bootloader adds the
+ * partitions.
+ */
+ partitions {
+ status = "disabled";
+ };
+
+ nand at 0 {
+ reg = <0>;
+ /*
+ * Some devices use Micron NAND with with 8 bit ECC
+ * other AMD/Spansion NAND with 4 bit ECC
+ *nand-ecc-strength = <4>;
+ *nand-ecc-step-size = <512>;
+ */
+ nand-bus-width = <8>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "0:sbl1";
+ reg = <0x0 0x100000>;
+ read-only;
+ };
+
+ partition at 100000 {
+ label = "0:mibib";
+ reg = <0x100000 0x100000>;
+ read-only;
+ };
+
+ partition at 200000 {
+ label = "0:bootconfig";
+ reg = <0x200000 0x80000>;
+ read-only;
+ };
+
+ partition at 280000 {
+ label = "0:bootconfig1";
+ reg = <0x280000 0x80000>;
+ read-only;
+ };
+
+ partition at 300000 {
+ label = "0:qsee";
+ reg = <0x300000 0x300000>;
+ read-only;
+ };
+
+ partition at 600000 {
+ label = "0:qsee_1";
+ reg = <0x600000 0x300000>;
+ read-only;
+ };
+
+ partition at 900000 {
+ label = "0:devcfg";
+ reg = <0x900000 0x80000>;
+ read-only;
+ };
+
+ partition at 980000 {
+ label = "0:devcfg_1";
+ reg = <0x980000 0x80000>;
+ read-only;
+ };
+
+ partition at a00000 {
+ label = "0:apdp";
+ reg = <0xa00000 0x80000>;
+ read-only;
+ };
+
+ partition at a80000 {
+ label = "0:apdp_1";
+ reg = <0xa80000 0x80000>;
+ read-only;
+ };
+
+ partition at b00000 {
+ label = "0:rpm";
+ reg = <0xb00000 0x80000>;
+ read-only;
+ };
+
+ partition at b80000 {
+ label = "0:rpm_1";
+ reg = <0xb80000 0x80000>;
+ read-only;
+ };
+
+ partition at c00000 {
+ label = "0:cdt";
+ reg = <0xc00000 0x80000>;
+ read-only;
+ };
+
+ partition at c80000 {
+ label = "0:cdt_1";
+ reg = <0xc80000 0x80000>;
+ read-only;
+ };
+
+ partition at d00000 {
+ label = "0:appsblenv";
+ reg = <0xd00000 0x80000>;
+ };
+
+ partition at d80000 {
+ label = "0:appsbl";
+ reg = <0xd80000 0x100000>;
+ read-only;
+ };
+
+ partition at e80000 {
+ label = "0:appsbl_1";
+ reg = <0xe80000 0x100000>;
+ read-only;
+ };
+
+ partition at f80000 {
+ label = "0:art";
+ reg = <0xf80000 0x80000>;
+ read-only;
+ };
+
+ partition at 1000000 {
+ label = "u_env";
+ reg = <0x1000000 0x100000>;
+ };
+
+ partition at 1100000 {
+ label = "s_env";
+ reg = <0x1100000 0x100000>;
+ };
+
+ partition at 1200000 {
+ label = "devinfo";
+ reg = <0x1200000 0x40000>;
+ read-only;
+ };
+
+ partition at 1240000 {
+ label = "kernel";
+ reg = <0x1240000 0xaf40000>;
+ };
+
+ partition at 1a40000 {
+ label = "rootfs";
+ reg = <0x1a40000 0xa740000>;
+ };
+
+ partition at c180000 {
+ label = "alt_kernel";
+ reg = <0xc180000 0xaf40000>;
+ };
+
+ partition at c980000 {
+ label = "alt_rootfs";
+ reg = <0xc980000 0xa740000>;
+ };
+
+ partition at 170c0000 {
+ label = "sysdiag";
+ reg = <0x170c0000 0x400000>;
+ read-only;
+ };
+
+ partition at 174c0000 {
+ label = "0:ethphyfw";
+ reg = <0x174c0000 0x80000>;
+ read-only;
+ };
+
+ partition at 17540000 {
+ label = "syscfg";
+ reg = <0x17540000 0x79c0000>;
+ read-only;
+ };
+
+ partition at 1ef00000 {
+ label = "secured_store";
+ reg = <0x1ef00000 0x400000>;
+ read-only;
+ };
+
+ partition at 1f300000 {
+ label = "0:wififw";
+ reg = <0x1f300000 0x1900000>;
+ read-only;
+ };
+
+ partition at 20c00000 {
+ label = "app2_data";
+ reg = <0x20c00000 0x16180000>;
+ read-only;
+ };
+
+ partition at 36d80000 {
+ label = "app2";
+ reg = <0x36d80000 0x9280000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&dp2 {
+ status = "okay";
+ phy-handle = <&qca8075_1>;
+ label = "wan";
+};
+
+&dp3 {
+ status = "okay";
+ phy-handle = <&qca8075_2>;
+ label = "lan3";
+};
+
+&dp4 {
+ status = "okay";
+ phy-handle = <&qca8075_3>;
+ label = "lan2";
+};
+
+&dp5 {
+ status = "okay";
+ phy-handle = <&qca8075_4>;
+ label = "lan1";
+};
+
+&wifi {
+ status = "okay";
+
+ qcom,ath11k-calibration-variant = "Linksys-MX4200v1";
+};
diff --git a/target/linux/qualcommax/image/ipq807x.mk b/target/linux/qualcommax/image/ipq807x.mk
index c42393eb79..77d89b6938 100644
--- a/target/linux/qualcommax/image/ipq807x.mk
+++ b/target/linux/qualcommax/image/ipq807x.mk
@@ -190,6 +190,17 @@ define Device/linksys_mx4200v2
endef
TARGET_DEVICES += linksys_mx4200v2
+define Device/linksys_mx4300
+ $(call Device/linksys_mx4x00)
+ DEVICE_MODEL := MX4300
+ BLOCKSIZE := 256k
+ PAGESIZE := 4096
+ KERNEL_SIZE := 8192k
+ IMAGE_SIZE := 171264k
+ NAND_SIZE := 1024m
+endef
+TARGET_DEVICES += linksys_mx4300
+
define Device/linksys_mx5300
$(call Device/linksys_mx)
DEVICE_MODEL := MX5300
diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network
index 373807048d..edb1ae9557 100644
--- a/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network
+++ b/target/linux/qualcommax/ipq807x/base-files/etc/board.d/02_network
@@ -29,6 +29,7 @@ ipq807x_setup_interfaces()
compex,wpq873|\
linksys,mx4200v1|\
linksys,mx4200v2|\
+ linksys,mx4300|\
prpl,haze|\
redmi,ax6|\
spectrum,sax1v1k|\
@@ -80,7 +81,8 @@ ipq807x_setup_macs()
local label_mac=""
case "$board" in
- linksys,mx4200v2)
+ linksys,mx4200v2|\
+ linksys,mx4300)
label_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
[ "$(mtd_get_mac_ascii u_env eth1addr)" != "$label_mac" ] && wan_mac=$label_mac
[ "$(mtd_get_mac_ascii u_env eth2addr)" != "$label_mac" ] && lan_mac=$label_mac
diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata b/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
index 2e741f0448..34c0a476d3 100644
--- a/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
+++ b/target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
@@ -44,6 +44,14 @@ case "$FIRMWARE" in
ath11k_remove_regdomain
ath11k_set_macflag
;;
+ linksys,mx4300)
+ caldata_extract "0:art" 0x1000 0x20000
+ label_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
+ ath11k_patch_mac $(macaddr_add $label_mac 2) 0
+ ath11k_patch_mac $(macaddr_add $label_mac 1) 1
+ ath11k_patch_mac $(macaddr_add $label_mac 3) 2
+ ath11k_remove_regdomain
+ ;;
netgear,rax120v2)
caldata_extract "0:art" 0x1000 0x20000
ath11k_patch_mac $(mtd_get_mac_binary boarddata1 0xc) 0
diff --git a/target/linux/qualcommax/ipq807x/base-files/etc/init.d/bootcount b/target/linux/qualcommax/ipq807x/base-files/etc/init.d/bootcount
index 26da7cd614..176a5a144a 100755
--- a/target/linux/qualcommax/ipq807x/base-files/etc/init.d/bootcount
+++ b/target/linux/qualcommax/ipq807x/base-files/etc/init.d/bootcount
@@ -12,6 +12,7 @@ boot() {
;;
linksys,mx4200v1|\
linksys,mx4200v2|\
+ linksys,mx4300|\
linksys,mx5300|\
linksys,mx8500)
mtd resetbc s_env || true
diff --git a/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh b/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh
index 70657629fc..0691c92184 100644
--- a/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh
+++ b/target/linux/qualcommax/ipq807x/base-files/lib/upgrade/platform.sh
@@ -168,6 +168,7 @@ platform_do_upgrade() {
;;
linksys,mx4200v1|\
linksys,mx4200v2|\
+ linksys,mx4300|\
linksys,mx5300|\
linksys,mx8500)
boot_part="$(fw_printenv -n boot_part)"
More information about the lede-commits
mailing list