[openwrt/openwrt] mediatek: filogic: add support for WAVLINK WL-WN573HX3
LEDE Commits
lede-commits at lists.infradead.org
Fri Apr 18 06:36:46 PDT 2025
blocktrron pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/907cb88e103b2e784caf0803b0ee668da28f2d14
commit 907cb88e103b2e784caf0803b0ee668da28f2d14
Author: Sebastian Schaper <openwrt at sebastianschaper.net>
AuthorDate: Sat Nov 2 19:28:18 2024 +0100
mediatek: filogic: add support for WAVLINK WL-WN573HX3
The WL-WN573HX3 is an AX3000 outdoor Access Point by WAVLINK,
also sold in Europe as 7Links WLR-1300 (ZX-5612).
Specifications:
- MT7981B + MT7976 AX3000 2x2 DBDC (160 MHz)
- 16 MiB SPI NOR, 256 MiB RAM
- Gigabit ethernet port, 802.3af PoE
- IP67 outdoor case for wall or pole mounting with
four single band RP-SMA fiberglass antennas (8 dBi)
Installation:
- OEM Web UI is at 192.168.30.1 which will forward to
http://netlogin.link (using a captive portal)
- login with default password `admin`
- skip setup wizard by navigating directly to
http://netlogin.link/html/meshUpgrade.html
- upload WN573HX3-sysupgrade.bin
- reset to factory defaults to discard OEM UCI settings
MAC address assignment:
LAN 80:xx:xx:76:xx:25 hw 0x44e
WLAN 2.4G 80:xx:xx:76:xx:27 factory 0x04 (label MAC)
WLAN 5G 82:xx:xx:46:xx:27
pair key 8a:xx:xx:76:xx:27 also on label, not used by OpenWrt
Signed-off-by: Sebastian Schaper <openwrt at sebastianschaper.net>
---
.../base-files/lib/preinit/05_set_preinit_iface | 3 +-
.../mediatek/dts/mt7981b-wavlink-wl-wn573hx3.dts | 188 +++++++++++++++++++++
.../filogic/base-files/etc/board.d/01_leds | 3 +-
.../filogic/base-files/etc/board.d/02_network | 1 +
.../etc/hotplug.d/ieee80211/11_fix_wifi_mac | 4 +
.../filogic/base-files/lib/upgrade/platform.sh | 3 +-
target/linux/mediatek/image/filogic.mk | 18 ++
7 files changed, 217 insertions(+), 3 deletions(-)
diff --git a/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface b/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface
index 1025d1f1e1..421f02938a 100644
--- a/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface
+++ b/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface
@@ -3,7 +3,8 @@ set_preinit_iface() {
cudy,m3000-v1|\
cudy,tr3000-v1|\
glinet,gl-mt3000|\
- openembed,som7981)
+ openembed,som7981|\
+ wavlink,wl-wn573hx3)
ip link set eth1 up
ifname=eth1
;;
diff --git a/target/linux/mediatek/dts/mt7981b-wavlink-wl-wn573hx3.dts b/target/linux/mediatek/dts/mt7981b-wavlink-wl-wn573hx3.dts
new file mode 100644
index 0000000000..ff222247a6
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7981b-wavlink-wl-wn573hx3.dts
@@ -0,0 +1,188 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+/dts-v1/;
+
+#include "mt7981.dtsi"
+
+/ {
+ model = "WAVLINK WL-WN573HX3";
+ compatible = "wavlink,wl-wn573hx3", "mediatek,mt7981";
+
+ aliases {
+ label-mac-device = &wifi;
+
+ led-boot = &led_status_blue;
+ led-failsafe = &led_status_blue;
+ led-running = &led_status_blue;
+ led-upgrade = &led_status_blue;
+
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ button-reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&pio 0 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ gpios = <&pio 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_status_blue: led-1 {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&pio 13 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+ð {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio_pins>;
+
+ status = "okay";
+
+ gmac1: mac at 1 {
+ compatible = "mediatek,eth-mac";
+ reg = <1>;
+ phy-mode = "gmii";
+ phy-handle = <&int_gbe_phy>;
+ nvmem-cells = <&macaddr_hw_44e 0>;
+ nvmem-cell-names = "mac-address";
+ };
+};
+
+&spi0 {
+ status = "disabled";
+};
+
+&spi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_flash_pins>;
+ status = "okay";
+
+ flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+
+ spi-max-frequency = <52000000>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 00000 {
+ label = "bl2";
+ reg = <0x00000 0x40000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "u-boot-env";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ factory: partition at 50000 {
+ label = "factory";
+ reg = <0x50000 0xb0000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ eeprom_factory_0: eeprom at 0 {
+ reg = <0x0 0x1000>;
+ };
+ };
+ };
+
+ partition at 100000 {
+ label = "fip";
+ reg = <0x100000 0x80000>;
+ read-only;
+ };
+
+ partition at f0000 {
+ compatible = "denx,fit";
+ label = "firmware";
+ reg = <0x180000 0xe00000>;
+ };
+
+ partition at f80000 {
+ label = "hw";
+ reg = <0xf80000 0x80000>;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_hw_44e: macaddr at 44e {
+ compatible = "mac-base";
+ reg = <0x44e 0x11>;
+ #nvmem-cell-cells = <1>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&pio {
+ spi2_flash_pins: spi2-pins {
+ mux {
+ function = "spi";
+ groups = "spi2", "spi2_wp_hold";
+ };
+
+ conf-pu {
+ pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
+ drive-strength = <8>;
+ bias-pull-up = <103>;
+ };
+
+ conf-pd {
+ pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
+ drive-strength = <8>;
+ bias-pull-down = <103>;
+ };
+ };
+};
+
+&wifi {
+ status = "okay";
+
+ nvmem-cells = <&eeprom_factory_0>;
+ nvmem-cell-names = "eeprom";
+};
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
index 58ee1ad619..e22bea3dd7 100644
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
@@ -44,7 +44,8 @@ bananapi,bpi-r4-poe)
ucidef_set_led_netdev "lan2" "lan2" "mt7530-0:02:green:lan" "lan2" "link tx rx"
ucidef_set_led_netdev "lan3" "lan3" "mt7530-0:03:green:lan" "lan3" "link tx rx"
;;
-cudy,re3000-v1)
+cudy,re3000-v1|\
+wavlink,wl-wn573hx3)
ucidef_set_led_netdev "lan" "lan" "green:lan" "eth0" "link tx rx"
;;
cudy,wr3000-v1)
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
index c81e70e19b..82c3efcbc7 100644
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
@@ -88,6 +88,7 @@ mediatek_setup_interfaces()
cudy,re3000-v1|\
netgear,wax220|\
ubnt,unifi-6-plus|\
+ wavlink,wl-wn573hx3|\
zyxel,nwa50ax-pro)
ucidef_set_interface_lan "eth0"
;;
diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
index 22e6e45436..228c9bae80 100644
--- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
+++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
@@ -186,6 +186,10 @@ case "$board" in
addr=$(mtd_get_mac_binary "Factory" 0x4)
[ "$PHYNBR" = "1" ] && macaddr_add $addr 1 > /sys${DEVPATH}/macaddress
;;
+ wavlink,wl-wn573hx3)
+ addr=$(mtd_get_mac_binary factory 0x04)
+ [ "$PHYNBR" = "1" ] && macaddr_setbit_la $(macaddr_add $addr -0x300000) > /sys${DEVPATH}/macaddress
+ ;;
zyxel,nwa50ax-pro)
hw_mac_addr="$(mtd_get_mac_binary mrd 0x1fff8)"
[ "$PHYNBR" = "0" ] && macaddr_add $hw_mac_addr 1 > /sys${DEVPATH}/macaddress
diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
index c40fe825c2..c48b6ce60d 100755
--- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
+++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
@@ -132,7 +132,8 @@ platform_do_upgrade() {
;;
cudy,re3000-v1|\
cudy,wr3000-v1|\
- yuncore,ax835)
+ yuncore,ax835|\
+ wavlink,wl-wn573hx3)
default_do_upgrade "$1"
;;
dlink,aquila-pro-ai-m30-a1|\
diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk
index b2edaa389d..3eb930f6d6 100644
--- a/target/linux/mediatek/image/filogic.mk
+++ b/target/linux/mediatek/image/filogic.mk
@@ -1678,6 +1678,24 @@ define Device/wavlink_wl-wn586x3
endef
TARGET_DEVICES += wavlink_wl-wn586x3
+define Device/wavlink_wl-wn573hx3
+ DEVICE_VENDOR := WAVLINK
+ DEVICE_MODEL := WL-WN573HX3
+ DEVICE_ALT0_VENDOR := 7Links
+ DEVICE_ALT0_MODEL := WLR-1300
+ DEVICE_DTS := mt7981b-wavlink-wl-wn573hx3
+ DEVICE_DTS_DIR := ../dts
+ DEVICE_DTS_LOADADDR := 0x47000000
+ IMAGE_SIZE := 14336k
+ KERNEL := kernel-bin | lzma | \
+ fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
+ DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware
+ SUPPORTED_DEVICES += mediatek,mt7981-spim-nor-rfb
+ IMAGES = WN573HX3-sysupgrade.bin
+ IMAGE/WN573HX3-sysupgrade.bin := append-kernel | pad-to 128k | append-rootfs | pad-rootfs | check-size | append-metadata
+endef
+TARGET_DEVICES += wavlink_wl-wn573hx3
+
define Device/xiaomi_mi-router-ax3000t
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Mi Router AX3000T
More information about the lede-commits
mailing list