[openwrt/openwrt] ipq60xx: add support for TP-Link EAP623-Outdoor HD v1
LEDE Commits
lede-commits at lists.infradead.org
Wed Apr 9 00:50:35 PDT 2025
robimarko pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/5dbf93c8c56edb919d0a02a1981ae3c28cb983ef
commit 5dbf93c8c56edb919d0a02a1981ae3c28cb983ef
Author: Yang Xiwen <forbidden405 at outlook.com>
AuthorDate: Mon Mar 31 08:48:23 2025 +0800
ipq60xx: add support for TP-Link EAP623-Outdoor HD v1
Specifications:
* SoC: Qualcomm IPQ6018 (64-bit Quad-core Arm Cortex-A53 @ 1800MHz)
* Memory: 1 GiB
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCN9074 (4x4 5 GHz 802.11ax)
* Wi-Fi: IPQ6018 (4x4 2.4 GHz 802.11b/g/n/ax)
* Ethernet: RTL8211F (10/100/1GBASE-T)
* Flash: ESMT F59D1G81MB (128 MiB)
* LEDs: 1x Green Status (GPIO 37 Active High), 1x Yellow Status (GPIO 32
Active High) and an LED global control GPIO (GPIO 36 Active High, set
up by U-Boot)
* Buttons: 1x Reset (GPIO 9 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to the pads near T32 and T31.
2. Connect 3V3 TTL port to TX, RX, and GND, which are pad T31, T32 and
the pad near T31 respectively. Be sure not to connect VCC and
crossover TX and RX.
3. Copy RAM firmware image
openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-initramfs-uImage.itb
to TFTP server root, available at 192.168.0.1.
4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the
serial console (115200 baud) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# setenv serverip 192.168.0.1
# setenv ipaddr 192.168.0.99
# tftpboot 0x44000000 openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-squashfs-sysupgrade.bin root at 192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Signed-off-by: Yang Xiwen <forbidden405 at outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18389
Signed-off-by: Robert Marko <robimarko at gmail.com>
---
.../uboot-envtools/files/qualcommax_ipq60xx | 3 +-
package/firmware/ipq-wifi/Makefile | 2 +
.../arm64/boot/dts/qcom/ipq6018-eap623od-hd-v1.dts | 151 +++++++++++++++++++++
target/linux/qualcommax/image/ipq60xx.mk | 16 +++
.../ipq60xx/base-files/etc/board.d/02_network | 6 +-
.../etc/hotplug.d/firmware/11-ath11k-caldata | 3 +-
.../base-files/lib/preinit/09_mount_factory_data | 3 +-
.../ipq60xx/base-files/lib/upgrade/platform.sh | 3 +-
8 files changed, 181 insertions(+), 6 deletions(-)
diff --git a/package/boot/uboot-tools/uboot-envtools/files/qualcommax_ipq60xx b/package/boot/uboot-tools/uboot-envtools/files/qualcommax_ipq60xx
index 02926424ab..7a89f78e79 100644
--- a/package/boot/uboot-tools/uboot-envtools/files/qualcommax_ipq60xx
+++ b/package/boot/uboot-tools/uboot-envtools/files/qualcommax_ipq60xx
@@ -28,7 +28,8 @@ linksys,mr7500)
netgear,wax214|\
netgear,wax610|\
netgear,wax610y|\
-tplink,eap610-outdoor)
+tplink,eap610-outdoor|\
+tplink,eap623od-hd-v1)
ubootenv_add_mtd "0:appsblenv" "0x0" "0x40000" "0x20000"
;;
yuncore,fap650)
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile
index 45109491f1..bf7d553df3 100644
--- a/package/firmware/ipq-wifi/Makefile
+++ b/package/firmware/ipq-wifi/Makefile
@@ -68,6 +68,7 @@ ALLWIFIBOARDS:= \
spectrum_sax1v1k \
tplink_eap610-outdoor \
tplink_eap620hd-v1 \
+ tplink_eap623od-hd-v1 \
tplink_eap660hd-v1 \
wallys_dr40x9 \
xiaomi_ax3600 \
@@ -216,6 +217,7 @@ $(eval $(call generate-ipq-wifi-package,skspruce_wia3300-20,SKSpruce WIA3300-20)
$(eval $(call generate-ipq-wifi-package,spectrum_sax1v1k,Spectrum SAX1V1K))
$(eval $(call generate-ipq-wifi-package,tplink_eap610-outdoor,TPLink EAP610-Outdoor))
$(eval $(call generate-ipq-wifi-package,tplink_eap620hd-v1,TP-Link EAP620 HD v1))
+$(eval $(call generate-ipq-wifi-package,tplink_eap623od-hd-v1,TP-Link EAP623-Outdoor HD v1))
$(eval $(call generate-ipq-wifi-package,tplink_eap660hd-v1,TP-Link EAP660 HD v1))
$(eval $(call generate-ipq-wifi-package,wallys_dr40x9,Wallys DR40X9))
$(eval $(call generate-ipq-wifi-package,xiaomi_ax3600,Xiaomi AX3600))
diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq6018-eap623od-hd-v1.dts b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq6018-eap623od-hd-v1.dts
new file mode 100644
index 0000000000..a4e49c9d6f
--- /dev/null
+++ b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq6018-eap623od-hd-v1.dts
@@ -0,0 +1,151 @@
+// SPDX-License-Identifier: MIT, GPL-2.0 or later
+/* Copyright (c) 2025, Yang Xiwen <forbidden405 at outlook.com> */
+
+/dts-v1/;
+
+#include "ipq6018.dtsi"
+#include "ipq6018-cp-cpu.dtsi"
+#include "ipq6018-ess.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "TP-Link EAP623-Outdoor HD V1.0";
+ compatible = "tplink,eap623od-hd-v1", "qcom,ipq6018";
+
+ aliases {
+ serial0 = &blsp1_uart3;
+ led-boot = &led_system;
+ led-failsafe = &led_system;
+ led-running = &led_system;
+ led-upgrade = &led_system;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs-append = " root=/dev/ubiblock0_1";
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_system: system {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan {
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_WLAN;
+ gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&blsp1_uart3 {
+ pinctrl-0 = <&serial_3_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&tlmm {
+ mdio_pins: mdio-pins {
+ mdc {
+ pins = "gpio64";
+ function = "mdc";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ mdio {
+ pins = "gpio65";
+ function = "mdio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+
+ phy_pins: phy-reset-pin {
+ pins = "gpio77";
+ function = "gpio";
+ bias-pull-up;
+ };
+};
+
+&mdio {
+ status = "okay";
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+
+ rtl8211f: ethernet-phy at 4 {
+ compatible = "ethernet-phy-id001c.c916";
+ reg = <4>;
+ reset-gpios = <&tlmm 77 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&phy_pins>;
+ pinctrl-names = "default";
+
+ realtek,clkout-disable;
+ realtek,aldps-enable;
+ };
+};
+
+&switch {
+ status = "okay";
+ switch_lan_bmp = <ESS_PORT5>; /* lan port bitmap */
+ switch_mac_mode1 = <MAC_MODE_SGMII_PLUS>; /* mac mode for uniphy instance0*/
+
+ qcom,port_phyinfo {
+ port at 5 {
+ port_id = <5>;
+ phy_address = <4>;
+ port_mac_sel = "QGMAC_PORT";
+ };
+ };
+};
+
+&edma {
+ status = "okay";
+};
+
+&dp5 {
+ status = "okay";
+ phy-handle = <&rtl8211f>;
+ phy-mode = "sgmii";
+ label = "lan";
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&qpic_nand {
+ status = "okay";
+
+ nand at 0 {
+ reg = <0>;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ nand-bus-width = <8>;
+
+ partitions {
+ compatible = "qcom,smem-part";
+ };
+ };
+};
+
+&wifi {
+ qcom,ath11k-calibration-variant = "TPLink-EAP623-Outdoor-HD-v1";
+ status = "okay";
+};
diff --git a/target/linux/qualcommax/image/ipq60xx.mk b/target/linux/qualcommax/image/ipq60xx.mk
index 8c77890966..5c630df3a6 100644
--- a/target/linux/qualcommax/image/ipq60xx.mk
+++ b/target/linux/qualcommax/image/ipq60xx.mk
@@ -167,6 +167,22 @@ define Device/tplink_eap610-outdoor
endef
TARGET_DEVICES += tplink_eap610-outdoor
+define Device/tplink_eap623od-hd-v1
+ $(call Device/FitImage)
+ $(call Device/UbiFit)
+ DEVICE_VENDOR := TP-Link
+ DEVICE_MODEL := EAP623-Outdoor HD
+ DEVICE_VARIANT := v1
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ SOC := ipq6018
+ DEVICE_PACKAGES := ipq-wifi-tplink_eap623od-hd-v1 kmod-phy-realtek
+ IMAGES += web-ui-factory.bin
+ IMAGE/web-ui-factory.bin := append-ubi | tplink-image-2022
+ TPLINK_SUPPORT_STRING := SupportList:\r\nEAP623-Outdoor HD(TP-Link|UN|AX1800-D):1.0\r\n
+endef
+TARGET_DEVICES += tplink_eap623od-hd-v1
+
define Device/yuncore_fap650
$(call Device/FitImage)
$(call Device/UbiFit)
diff --git a/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network b/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network
index f907a29ae0..a3a86490de 100644
--- a/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network
+++ b/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network
@@ -32,7 +32,8 @@ ipq60xx_setup_interfaces()
;;
netgear,wax610|\
netgear,wax610y|\
- tplink,eap610-outdoor)
+ tplink,eap610-outdoor|\
+ tplink,eap623od-hd-v1)
ucidef_set_interface_lan "lan" "dhcp"
;;
*)
@@ -54,7 +55,8 @@ ipq60xx_setup_macs()
wan_mac=$(macaddr_add "$lan_mac" 1)
label_mac=$lan_mac
;;
- tplink,eap610-outdoor)
+ tplink,eap610-outdoor|\
+ tplink,eap623od-hd-v1)
label_mac=$(get_mac_binary /tmp/factory_data/default-mac 0)
lan_mac=$label_mac
;;
diff --git a/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11k-caldata b/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
index ef8afd6bd4..8102524e30 100644
--- a/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
+++ b/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
@@ -50,7 +50,8 @@ case "$FIRMWARE" in
ath11k_patch_mac $(macaddr_add $label_mac 2) 1
ath11k_set_macflag
;;
- tplink,eap610-outdoor)
+ tplink,eap610-outdoor|\
+ tplink,eap623od-hd-v1)
caldata_from_file "/tmp/factory_data/radio" 0 0x10000
label_mac=$(get_mac_binary /tmp/factory_data/default-mac 0)
ath11k_patch_mac $label_mac 1
diff --git a/target/linux/qualcommax/ipq60xx/base-files/lib/preinit/09_mount_factory_data b/target/linux/qualcommax/ipq60xx/base-files/lib/preinit/09_mount_factory_data
index 97608db55d..488267a01b 100644
--- a/target/linux/qualcommax/ipq60xx/base-files/lib/preinit/09_mount_factory_data
+++ b/target/linux/qualcommax/ipq60xx/base-files/lib/preinit/09_mount_factory_data
@@ -7,7 +7,8 @@ preinit_mount_factory_data() {
. /lib/functions/system.sh
case $(board_name) in
- tplink,eap610-outdoor)
+ tplink,eap610-outdoor|\
+ tplink,eap623od-hd-v1)
mtd_path=$(find_mtd_chardev "factory_data")
ubiattach --dev-path="$mtd_path" --devn=1
mkdir /tmp/factory_data
diff --git a/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh b/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh
index bc3603682d..4588688405 100644
--- a/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh
@@ -133,7 +133,8 @@ platform_do_upgrade() {
fw_setenv auto_recovery yes
nand_do_upgrade "$1"
;;
- tplink,eap610-outdoor)
+ tplink,eap610-outdoor|\
+ tplink,eap623od-hd-v1)
tplink_do_upgrade "$1"
;;
yuncore,fap650)
More information about the lede-commits
mailing list