[openwrt/openwrt] ramips: Add support for D-Link DIR-2150-R1
LEDE Commits
lede-commits at lists.infradead.org
Sun Sep 22 10:39:12 PDT 2024
hauke pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/a1a8cd82829daa02390c7fb8d9c1076073a6ac33
commit a1a8cd82829daa02390c7fb8d9c1076073a6ac33
Author: Alan Luck <luckyhome2008 at gmail.com>
AuthorDate: Wed Jul 10 21:57:11 2024 +1000
ramips: Add support for D-Link DIR-2150-R1
Hardware Specification:
SoC: Mediatek MT7621DAT (MIPS1004Kc 880 MHz, dual core)
RAM: 128 MB
Storage: 128 MB NAND flash
Ethernet: 5x 10/100/1000 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
Wireless: 2.4GHz: Mediatek MT7603EN up to 300Mbps (802.11b/g/n MIMO 2x2)
Wireless: 5GHz: Mediatek MT7615N up to 1733Mbps (802.11n/ac MU-MIMO 4x4)
LEDs: Power (white & amber), Internet (white & amber)
LEDs: 2.4G (White), 5Ghz (White)
Buttons: WPS, Reset
USB: Front V3.0 & Rear V2.0
MAC Table
Label xx:xx:xx:xx:xx:38
LAN xx:xx:xx:xx:xx:39
2.4Ghz xx:xx:xx:xx:xx:3A
5Ghz xx:xx:xx:xx:xx:3C
WAN xx:xx:xx:xx:xx:38
Flash Instructions:
D-Link normal OEM firmware update page
1. upload OpenWRT factory.bin like any D-Link upgrade image
D-Link Fail Safe GUI:
1. Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable.
2. Give it ~30 seconds, to boot the fail safe GUI
3. Connect your client computer to LAN1 of the device
4. Set your client IP address manually to 192.168.0.2 / 255.255.255.0
5. Call the fail safe page for the device at http://192.168.0.1/
6. Use the provided fail safe web GUI to upload the factory.bin to the device
Signed-off-by: Alan Luck <luckyhome2008 at gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16269
Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
---
.../linux/ramips/dts/mt7621_dlink_dir-2150-r1.dts | 199 +++++++++++++++++++++
target/linux/ramips/image/mt7621.mk | 14 ++
.../ramips/mt7621/base-files/etc/board.d/01_leds | 1 +
.../mt7621/base-files/lib/upgrade/platform.sh | 1 +
4 files changed, 215 insertions(+)
diff --git a/target/linux/ramips/dts/mt7621_dlink_dir-2150-r1.dts b/target/linux/ramips/dts/mt7621_dlink_dir-2150-r1.dts
new file mode 100644
index 0000000000..8a1bae328f
--- /dev/null
+++ b/target/linux/ramips/dts/mt7621_dlink_dir-2150-r1.dts
@@ -0,0 +1,199 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ compatible = "dlink,dir-2150-r1", "mediatek,mt7621-soc";
+ model = "D-Link DIR-2150 R1";
+
+ aliases {
+ label-mac-device = &gmac1;
+ led-boot = &led_power_orange;
+ led-failsafe = &led_power_white;
+ led-running = &led_power_white;
+ led-upgrade = &led_net_orange;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power_orange: led-0 {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_ORANGE>;
+ gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+ };
+
+ led_power_white: led-1 {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ };
+
+ led_net_orange: led-2 {
+ function = LED_FUNCTION_WAN;
+ color = <LED_COLOR_ID_ORANGE>;
+ gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+ };
+
+ led-3 {
+ function = LED_FUNCTION_WAN;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&nand {
+ status = "okay";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "Bootloader";
+ reg = <0x0 0x80000>;
+ read-only;
+ };
+
+ partition at 80000 {
+ label = "config";
+ reg = <0x80000 0x80000>;
+ read-only;
+ };
+
+ partition at 100000 {
+ label = "factory";
+ reg = <0x100000 0x40000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ eeprom_factory_0: eeprom at 0 {
+ reg = <0x0 0x400>;
+ };
+
+ eeprom_factory_8000: eeprom at 8000 {
+ reg = <0x8000 0x4da8>;
+ };
+
+ macaddr_factory_e006: macaddr at e006 {
+ compatible = "mac-base";
+ reg = <0xe006 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+ };
+ };
+
+ partition at 140000 {
+ label = "firmware";
+ compatible = "denx,uimage";
+ reg = <0x140000 0x7E80000>;
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pcie0 {
+ wifi at 0,0 {
+ compatible = "mediatek,mt76";
+ reg = <0x0000 0 0 0 0>;
+ nvmem-cells = <&eeprom_factory_0>, <&macaddr_factory_e006 2>;
+ nvmem-cell-names = "eeprom", "mac-address";
+ ieee80211-freq-limit = <2400000 2500000>;
+
+ led {
+ led-active-low;
+ };
+ };
+};
+
+&pcie1 {
+ wifi at 0,0 {
+ compatible = "mediatek,mt76";
+ reg = <0x0000 0 0 0 0>;
+ nvmem-cells = <&eeprom_factory_8000>, <&macaddr_factory_e006 4>;
+ nvmem-cell-names = "eeprom", "mac-address";
+ ieee80211-freq-limit = <5000000 6000000>;
+
+ led {
+ led-active-low;
+ };
+ };
+};
+
+&gmac0 {
+ nvmem-cells = <&macaddr_factory_e006 1>;
+ nvmem-cell-names = "mac-address";
+};
+
+&gmac1 {
+ status = "okay";
+ label = "wan";
+ phy-handle = <ðphy4>;
+
+ nvmem-cells = <&macaddr_factory_e006 0>;
+ nvmem-cell-names = "mac-address";
+};
+
+ðphy4 {
+ /delete-property/ interrupts;
+};
+
+&switch0 {
+ ports {
+ port at 0 {
+ status = "okay";
+ label = "lan4";
+ };
+
+ port at 1 {
+ status = "okay";
+ label = "lan3";
+ };
+
+ port at 2 {
+ status = "okay";
+ label = "lan2";
+ };
+
+ port at 3 {
+ status = "okay";
+ label = "lan1";
+ };
+ };
+};
+
+&state_default {
+ gpio {
+ groups = "i2c", "uart3", "jtag", "wdt";
+ function = "gpio";
+ };
+};
diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk
index 246276c7db..2932f13e99 100644
--- a/target/linux/ramips/image/mt7621.mk
+++ b/target/linux/ramips/image/mt7621.mk
@@ -916,6 +916,20 @@ define Device/dlink_dir-2150-a1
endef
TARGET_DEVICES += dlink_dir-2150-a1
+define Device/dlink_dir-2150-r1
+ $(Device/nand)
+ IMAGE_SIZE := 129536k
+ DEVICE_VENDOR := D-Link
+ DEVICE_MODEL := DIR-2150
+ DEVICE_VARIANT := R1
+ DEVICE_PACKAGES := -uboot-envtools kmod-mt7603 kmod-mt7615-firmware kmod-usb3
+ KERNEL := $$(KERNEL)
+ IMAGES += factory.bin
+ IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | \
+ check-size | sign-dlink-ru e6587b35a6b34e07bedeca23e140322f
+endef
+TARGET_DEVICES += dlink_dir-2150-r1
+
define Device/dlink_dir-2640-a1
$(Device/dlink_dir_nand_128m)
DEVICE_MODEL := DIR-2640
diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
index c18724a2be..9a77b1b1bc 100644
--- a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
@@ -94,6 +94,7 @@ dlink,dap-x1860-a1)
dlink,dir-1960-a1|\
dlink,dir-2055-a1|\
dlink,dir-2150-a1|\
+dlink,dir-2150-r1|\
dlink,dir-2640-a1|\
dlink,dir-2660-a1)
ucidef_set_led_netdev "wan" "wan" "white:wan" "wan"
diff --git a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh
index 4c8276bd49..97887ca8c3 100755
--- a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh
@@ -85,6 +85,7 @@ platform_do_upgrade() {
dlink,dir-1960-a1|\
dlink,dir-2055-a1|\
dlink,dir-2150-a1|\
+ dlink,dir-2150-r1|\
dlink,dir-2640-a1|\
dlink,dir-2660-a1|\
dlink,dir-3040-a1|\
More information about the lede-commits
mailing list