[openwrt/openwrt] bcm53xx: enable CONFIG_I2C_BCM_IPROC

[LEDE Commits]

hauke pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/a69eaf80796fda2df7bbae74af62e700000aff19

commit a69eaf80796fda2df7bbae74af62e700000aff19
Author: Lech Perczak <lech.perczak at gmail.com>
AuthorDate: Wed Oct 2 16:23:13 2024 +0200

    bcm53xx: enable CONFIG_I2C_BCM_IPROC
    
    This is required for the AT24 EEPROM holding MAC address on Meraki
    devices to probe before preinit starts, so all network devices can be
    available at the preinit network setup starts
    
    Signed-off-by: Lech Perczak <lech.perczak at gmail.com>
    Link: https://github.com/openwrt/openwrt/pull/16634
    Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
---
 target/linux/bcm53xx/config-6.6     | 4 ++++
 target/linux/bcm53xx/image/Makefile | 6 ++----
 2 files changed, 6 insertions(+), 4 deletions(-)

diff --git a/target/linux/bcm53xx/config-6.6 b/target/linux/bcm53xx/config-6.6
index 26fa023595..e9ac56416a 100644
--- a/target/linux/bcm53xx/config-6.6
+++ b/target/linux/bcm53xx/config-6.6
@@ -183,6 +183,9 @@ CONFIG_HW_RANDOM=y
 CONFIG_HW_RANDOM_BCM2835=y
 CONFIG_HZ_FIXED=0
 CONFIG_HZ_PERIODIC=y
+CONFIG_I2C=y
+CONFIG_I2C_BCM_IPROC=y
+# CONFIG_I2C_SLAVE_TESTUNIT is not set
 CONFIG_INITRAMFS_SOURCE=""
 CONFIG_IRQCHIP=y
 CONFIG_IRQSTACKS=y
@@ -294,6 +297,7 @@ CONFIG_PWM_SYSFS=y
 CONFIG_RANDSTRUCT_NONE=y
 CONFIG_RATIONAL=y
 CONFIG_REGMAP=y
+CONFIG_REGMAP_I2C=y
 CONFIG_REGMAP_MMIO=y
 CONFIG_RFS_ACCEL=y
 CONFIG_RPS=y
diff --git a/target/linux/bcm53xx/image/Makefile b/target/linux/bcm53xx/image/Makefile
index 501486c063..8318450293 100644
--- a/target/linux/bcm53xx/image/Makefile
+++ b/target/linux/bcm53xx/image/Makefile
@@ -382,8 +382,7 @@ TARGET_DEVICES += luxul_xwr-3150
 define Device/meraki_mr26
   DEVICE_VENDOR := Meraki
   DEVICE_MODEL := MR26
-  DEVICE_PACKAGES := $(B43) kmod-i2c-bcm-iproc \
-	kmod-hwmon-ina2xx kmod-leds-uleds nu801
+  DEVICE_PACKAGES := $(B43) kmod-hwmon-ina2xx kmod-leds-uleds nu801
   DEVICE_DTS := bcm53015-meraki-mr26
 # resize the initramfs to fit the size of the existing part.safe.
   KERNEL_LOADADDR := 0x00008000
@@ -399,8 +398,7 @@ TARGET_DEVICES += meraki_mr26
 define Device/meraki_mr32
   DEVICE_VENDOR := Meraki
   DEVICE_MODEL := MR32
-  DEVICE_PACKAGES := $(B43) kmod-i2c-bcm-iproc \
-	kmod-leds-pwm kmod-hwmon-ina2xx kmod-bluetooth
+  DEVICE_PACKAGES := $(B43) kmod-leds-pwm kmod-hwmon-ina2xx kmod-bluetooth
   DEVICE_DTS := bcm53016-meraki-mr32
 # Meraki FW r23 tries to resize the part.safe partition before it will
 # flash the image. This is a bit of a problem, since resizing will fail