[openwrt/openwrt] ipq40xx: add support for SKSpruce WIA3300-20
LEDE Commits
lede-commits at lists.infradead.org
Tue Oct 8 10:33:40 PDT 2024
robimarko pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/b37f3def8690f8b81e2fb058a130358514bf2f93
commit b37f3def8690f8b81e2fb058a130358514bf2f93
Author: Shiji Yang <yangshiji66 at qq.com>
AuthorDate: Tue Sep 24 19:15:56 2024 +0800
ipq40xx: add support for SKSpruce WIA3300-20
Specification
-------------
- SoC : Qualcomm IPQ4019
- RAM : 256 MiB DDR3 (NT5CC128M16JR-EK)
- Flash : 64 MiB SPI NOR (Winbond W25Q512JVFQ)
- WLAN : IPQ4019 built-in
- 2.4 GHz : 2x2 MIMO WiFi4
- 5 GHz : 2x2 MIMO WiFi5
- Ethernet : QCA8075 10/100/1000 Mbps 1x WAN (ETH1, PoE); 1x LAN (ETH2)
- USB : 1x 2.0 Type-A
- UART : 3.3V, 115200n8
- Buttons : 1x Reset
- LEDs : 1x RUN (lime & red)
1x WiFi 2.4 GHz (lime)
1x WiFi 5 GHz (lime)
2x ETH (lime), controlled by the QCA8075 phy
- Power : DC 12V & 802.3at PoE
- FCC ID : 2AHKT-WIA3300-20
- TFTP IP :
- client : 192.168.18.254
- router : 192.168.18.1
Installation
------------
1. Open uart console and start TFTP server. Copy initramfs image to
the TFTP root directory and rename it to 'ipqinitramfs.bin'.
2. Power on and press 'Enter' to exit to the u-boot console according
to the TTL log prompt.
3. Execute commands to load the initramfs image:
tftpboot && bootm
4. Enter into OpenWrt to backup the partitions if you want to restore
the stock firmware one day.
5. Override default 'bootcmd' environment variable in u-boot console:
env set bootcmd 'sf probe && sf read $loadaddr 0x980000 0x800000 && bootm $loadaddr'
env save
6. Repeat step 3 and flash 'sysupgrade' image in OpenWrt.
Recovery and return to stock
----------------------------
1. Restore the backup firmware partitions in the installation step 4.
2. Restore `bootcmd` environment variable via commands:
env set bootcmd bootipq && env save
MAC addresses
-------------
+---------+-------------------+
| | MAC example |
+---------+-------------------+
| LABEL | xx:xx:xx:xx:xx:25 |
| LAN | xx:xx:xx:xx:xx:26 |
| WAN | xx:xx:xx:xx:xx:25 |
| WLAN 2g | xx:xx:xx:xx:xx:28 |
| WLAN 5g | xx:xx:xx:xx:xx:29 |
+---------+-------------------+
Notice
-----------
1. Some CH340 USB-TTL module doesn't work on this device.
2. The 'firmware' partition consists of four parts in the vendor
layout:
* Name Start Size
* rootfs 0x980000 0x1680000
* 0:HLOS1 0x2000000 0x800000
* rootfs_1 0x2800000 0x1400000
* rootfs_data 0x3c00000 0x350000
3. User can control the USB power supply via commands:
echo enabled > /sys/devices/platform/output-usb-power/state
echo disabled > /sys/devices/platform/output-usb-power/state
Signed-off-by: Shiji Yang <yangshiji66 at qq.com>
Link: https://github.com/openwrt/openwrt/pull/16476
Signed-off-by: Robert Marko <robimarko at gmail.com>
---
.../ipq40xx/base-files/etc/board.d/02_network | 3 +
.../arm/boot/dts/qcom/qcom-ipq4019-wia3300-20.dts | 446 +++++++++++++++++++++
target/linux/ipq40xx/image/generic.mk | 13 +
3 files changed, 462 insertions(+)
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 7a2874a6e4..e3a6e24228 100644
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -117,6 +117,9 @@ ipq40xx_setup_interfaces()
qxwlan,e2600ac-c2)
ucidef_set_interfaces_lan_wan "sw-eth1 sw-eth2" "sw-eth3"
;;
+ skspruce,wia3300-20)
+ ucidef_set_interfaces_lan_wan "ETH2" "ETH1"
+ ;;
zte,mf286d)
ucidef_set_interfaces_lan_wan "lan2 lan3 lan4" "wan"
;;
diff --git a/target/linux/ipq40xx/files-6.6/arch/arm/boot/dts/qcom/qcom-ipq4019-wia3300-20.dts b/target/linux/ipq40xx/files-6.6/arch/arm/boot/dts/qcom/qcom-ipq4019-wia3300-20.dts
new file mode 100644
index 0000000000..cb7d3a918f
--- /dev/null
+++ b/target/linux/ipq40xx/files-6.6/arch/arm/boot/dts/qcom/qcom-ipq4019-wia3300-20.dts
@@ -0,0 +1,446 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ compatible = "skspruce,wia3300-20", "qcom,ipq4019";
+ model = "SKSpruce WIA3300-20";
+
+ aliases {
+ label-mac-device = &gmac;
+ led-boot = &led_status_red;
+ led-failsafe = &led_status_lime;
+ led-running = &led_status_lime;
+ led-upgrade = &led_status_red;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ pinctrl-0 = <&key_pins>;
+ pinctrl-names = "default";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pinctrl-0 = <&led_pins>;
+ pinctrl-names = "default";
+
+ led_status_red: led-0 {
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&tlmm 8 GPIO_ACTIVE_LOW>;
+ };
+
+ led_status_lime: led-1 {
+ color = <LED_COLOR_ID_LIME>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
+ };
+
+ led-2 {
+ color = <LED_COLOR_ID_LIME>;
+ function = LED_FUNCTION_WLAN_2GHZ;
+ gpios = <&tlmm 11 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ led-3 {
+ color = <LED_COLOR_ID_LIME>;
+ function = LED_FUNCTION_WLAN_5GHZ;
+ gpios = <&tlmm 28 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+ };
+
+ output-usb-power {
+ compatible = "regulator-output";
+ vout-supply = <®_usb>;
+ };
+
+ reg_usb: regulator-usb {
+ compatible = "regulator-fixed";
+
+ pinctrl-0 = <®_usb_pins>;
+ pinctrl-names = "default";
+
+ enable-active-high;
+ gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>;
+ regulator-max-microvolt = <5000000>;
+ regulator-min-microvolt = <5000000>;
+ regulator-name = "reg_usb";
+ regulator-boot-on;
+ };
+
+ soc {
+ tcsr at 1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr at 194b000 {
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ };
+
+ ess_tcsr at 1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr at 1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ status = "okay";
+
+ pinctrl-0 = <&spi0_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>;
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <24000000>;
+ reg = <0>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "0:SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "0:MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+
+ partition at 60000 {
+ label = "0:QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+
+ partition at c0000 {
+ label = "0:CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+
+ partition at d0000 {
+ label = "0:DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+
+ partition at e0000 {
+ compatible = "u-boot,env";
+ label = "0:APPSBLENV";
+ reg = <0x000e0000 0x00010000>;
+ };
+
+ partition at f0000 {
+ label = "0:APPSBL";
+ reg = <0x000f0000 0x00080000>;
+ read-only;
+ };
+
+ partition at 170000 {
+ label = "0:oldART";
+ reg = <0x00170000 0x00010000>;
+ read-only;
+ };
+
+ partition at 180000 {
+ label = "0:HLOS";
+ reg = <0x00180000 0x00800000>;
+ read-only;
+ };
+
+ partition at 980000 {
+ compatible = "denx,fit";
+ label = "firmware";
+ reg = <0x980000 0x35d0000>;
+ };
+
+ partition at 3f50000 {
+ label = "0:APPSBL1";
+ reg = <0x03f50000 0x00080000>;
+ read-only;
+ };
+
+ partition at 3fd0000 {
+ label = "BoardInfo";
+ reg = <0x03fd0000 0x00010000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_boardinfo_108a: macaddr at 108a {
+ compatible = "mac-base";
+ reg = <0x108a 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+ };
+ };
+
+ partition at 3fe0000 {
+ label = "RebootCause";
+ reg = <0x03fe0000 0x00010000>;
+ read-only;
+ };
+
+ partition at 3ff0000 {
+ label = "0:ART";
+ reg = <0x03ff0000 0x00010000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ precal_art_1000: precal at 1000 {
+ reg = <0x1000 0x2f20>;
+ };
+
+ precal_art_5000: precal at 5000 {
+ reg = <0x5000 0x2f20>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&blsp1_uart1 {
+ status = "okay";
+
+ pinctrl-0 = <&serial0_pins>;
+ pinctrl-names = "default";
+};
+
+&crypto {
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+ðphy3 {
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led at 1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_LIME>;
+ function = LED_FUNCTION_LAN;
+ };
+ };
+};
+
+ðphy4 {
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led at 1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_LIME>;
+ function = LED_FUNCTION_WAN;
+ };
+ };
+};
+
+&gmac {
+ status = "okay";
+
+ nvmem-cells = <&macaddr_boardinfo_108a 0>;
+ nvmem-cell-names = "mac-address";
+};
+
+&mdio {
+ status = "okay";
+
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+
+ reset-delay-us = <2000>;
+ reset-post-delay-us = <2000>;
+ reset-gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
+};
+
+&prng {
+ status = "okay";
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&switch {
+ status = "okay";
+};
+
+&swport4 {
+ status = "okay";
+
+ label = "ETH2";
+ nvmem-cells = <&macaddr_boardinfo_108a 1>;
+ nvmem-cell-names = "mac-address";
+};
+
+&swport5 {
+ status = "okay";
+
+ label = "ETH1";
+ nvmem-cells = <&macaddr_boardinfo_108a 0>;
+ nvmem-cell-names = "mac-address";
+};
+
+&tlmm {
+ key_pins: key_pinmux {
+ gpio {
+ pins = "gpio18";
+ function = "gpio";
+ bias-disable;
+ };
+ };
+
+ led_pins: led_pinmux {
+ gpio {
+ pins = "gpio8", "gpio9", "gpio11", "gpio28";
+ function = "gpio";
+ drive-strength = <8>;
+ drive-open-drain;
+ bias-disable;
+ };
+ };
+
+ mdio_pins: mdio_pinmux {
+ gpio {
+ pins = "gpio43";
+ function = "gpio";
+ drive-strength = <4>;
+ bias-disable;
+ output-high;
+ };
+
+ mdc {
+ pins = "gpio7";
+ function = "mdc";
+ drive-strength = <4>;
+ bias-disable;
+ };
+
+ mdio {
+ pins = "gpio6";
+ function = "mdio";
+ drive-strength = <4>;
+ drive-open-drain;
+ bias-pull-up;
+ };
+ };
+
+ reg_usb_pins: reg_usb_pinmux {
+ gpio {
+ pins = "gpio25";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ serial0_pins: serial0_pinmux {
+ blsp_uart0 {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ spi0_pins: spi0_pinmux {
+ blsp_spi0 {
+ pins = "gpio13", "gpio14", "gpio15";
+ function = "blsp_spi0";
+ drive-strength = <4>;
+ bias-disable;
+ };
+
+ gpio {
+ pins = "gpio12";
+ function = "gpio";
+ drive-strength = <4>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&usb2 {
+ status = "okay";
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+
+ nvmem-cell-names = "mac-address", "pre-calibration";
+ nvmem-cells = <&macaddr_boardinfo_108a 3>, <&precal_art_1000>;
+ qcom,ath10k-calibration-variant = "SKSpruce_WIA3300-20";
+};
+
+&wifi1 {
+ status = "okay";
+
+ nvmem-cell-names = "mac-address", "pre-calibration";
+ nvmem-cells = <&macaddr_boardinfo_108a 4>, <&precal_art_5000>;
+ qcom,ath10k-calibration-variant = "SKSpruce_WIA3300-20";
+};
diff --git a/target/linux/ipq40xx/image/generic.mk b/target/linux/ipq40xx/image/generic.mk
index a2931ff01e..b5d387b14a 100644
--- a/target/linux/ipq40xx/image/generic.mk
+++ b/target/linux/ipq40xx/image/generic.mk
@@ -1092,6 +1092,19 @@ define Device/qxwlan_e2600ac-c2
endef
TARGET_DEVICES += qxwlan_e2600ac-c2
+define Device/skspruce_wia3300-20
+ $(call Device/FitImage)
+ BLOCKSIZE := 64k
+ IMAGE_SIZE := 55104k
+ SOC := qcom-ipq4019
+ DEVICE_VENDOR := SKSpruce
+ DEVICE_MODEL := WIA3300-20
+ DEVICE_PACKAGES := -ath10k-board-qca4019 ipq-wifi-skspruce_wia3300-20
+ IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
+ append-rootfs | pad-rootfs | check-size | append-metadata
+endef
+TARGET_DEVICES +=skspruce_wia3300-20
+
define Device/sony_ncp-hg100-cellular
$(call Device/FitImage)
DEVICE_VENDOR := Sony
More information about the lede-commits
mailing list