[openwrt/openwrt] uboot-mediatek: add Routerich AX3000 support
LEDE Commits
lede-commits at lists.infradead.org
Sun Nov 24 14:43:06 PST 2024
hauke pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/c0581520b1c53fe2fc4a310f916590dcc428474a
commit c0581520b1c53fe2fc4a310f916590dcc428474a
Author: Mikhail Zhilkin <csharper2005 at gmail.com>
AuthorDate: Sat Oct 26 09:34:43 2024 +0000
uboot-mediatek: add Routerich AX3000 support
Add U-Boot replacement loader for Routerich AX3000.
Signed-off-by: Mikhail Zhilkin <csharper2005 at gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16791
Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
---
package/boot/uboot-mediatek/Makefile | 13 +
.../patches/460-add-routerich-ax3000.patch | 362 +++++++++++++++++++++
2 files changed, 375 insertions(+)
diff --git a/package/boot/uboot-mediatek/Makefile b/package/boot/uboot-mediatek/Makefile
index d2a03277d4..fa314da399 100644
--- a/package/boot/uboot-mediatek/Makefile
+++ b/package/boot/uboot-mediatek/Makefile
@@ -413,6 +413,18 @@ define U-Boot/mt7981_rfb-snfi
DEPENDS:=+trusted-firmware-a-mt7981-snand-ddr3
endef
+define U-Boot/mt7981_routerich_ax3000
+ NAME:=Routerich AX3000
+ BUILD_SUBTARGET:=filogic
+ BUILD_DEVICES:=routerich_ax3000-ubootmod
+ UBOOT_CONFIG:=mt7981_routerich_ax3000
+ UBOOT_IMAGE:=u-boot.fip
+ BL2_BOOTDEV:=spim-nand
+ BL2_SOC:=mt7981
+ BL2_DDRTYPE:=ddr3
+ DEPENDS:=+trusted-firmware-a-mt7981-spim-nand-ddr3
+endef
+
define U-Boot/mt7981_qihoo_360t7
NAME:=Qihoo 360T7
BUILD_SUBTARGET:=filogic
@@ -823,6 +835,7 @@ UBOOT_TARGETS := \
mt7981_rfb-nor \
mt7981_rfb-sd \
mt7981_rfb-snfi \
+ mt7981_routerich_ax3000 \
mt7981_qihoo_360t7 \
mt7981_xiaomi_mi-router-ax3000t \
mt7981_xiaomi_mi-router-wr30u \
diff --git a/package/boot/uboot-mediatek/patches/460-add-routerich-ax3000.patch b/package/boot/uboot-mediatek/patches/460-add-routerich-ax3000.patch
new file mode 100644
index 0000000000..9aa31843de
--- /dev/null
+++ b/package/boot/uboot-mediatek/patches/460-add-routerich-ax3000.patch
@@ -0,0 +1,362 @@
+--- /dev/null
++++ b/configs/mt7981_routerich_ax3000_defconfig
+@@ -0,0 +1,107 @@
++CONFIG_ARM=y
++CONFIG_SYS_HAS_NONCACHED_MEMORY=y
++CONFIG_POSITION_INDEPENDENT=y
++CONFIG_ARCH_MEDIATEK=y
++CONFIG_TEXT_BASE=0x41e00000
++CONFIG_SYS_MALLOC_F_LEN=0x4000
++CONFIG_NR_DRAM_BANKS=1
++CONFIG_DEFAULT_DEVICE_TREE="mt7981-routerich_ax3000"
++CONFIG_OF_LIBFDT_OVERLAY=y
++CONFIG_TARGET_MT7981=y
++CONFIG_PRE_CON_BUF_ADDR=0x4007ef00
++CONFIG_DEBUG_UART_BASE=0x11002000
++CONFIG_DEBUG_UART_CLOCK=40000000
++CONFIG_SYS_LOAD_ADDR=0x46000000
++CONFIG_DEBUG_UART=y
++CONFIG_FIT=y
++CONFIG_BOOTDELAY=30
++CONFIG_AUTOBOOT_KEYED=y
++CONFIG_AUTOBOOT_MENU_SHOW=y
++CONFIG_DEFAULT_FDT_FILE="mediatek/mt7981-routerich_ax3000.dtb"
++CONFIG_LOGLEVEL=7
++CONFIG_PRE_CONSOLE_BUFFER=y
++CONFIG_LOG=y
++CONFIG_BOARD_LATE_INIT=y
++CONFIG_HUSH_PARSER=y
++CONFIG_SYS_PROMPT="MT7981> "
++CONFIG_CMD_CPU=y
++CONFIG_CMD_LICENSE=y
++CONFIG_CMD_BOOTMENU=y
++CONFIG_CMD_ASKENV=y
++CONFIG_CMD_ERASEENV=y
++CONFIG_CMD_ENV_FLAGS=y
++CONFIG_CMD_STRINGS=y
++CONFIG_CMD_DM=y
++CONFIG_CMD_GPIO=y
++CONFIG_CMD_GPT=y
++CONFIG_CMD_MTD=y
++CONFIG_CMD_PART=y
++CONFIG_CMD_DHCP=y
++CONFIG_CMD_TFTPSRV=y
++CONFIG_CMD_RARP=y
++CONFIG_CMD_PING=y
++CONFIG_CMD_CDP=y
++CONFIG_CMD_SNTP=y
++CONFIG_CMD_DNS=y
++CONFIG_CMD_LINK_LOCAL=y
++CONFIG_CMD_PXE=y
++CONFIG_CMD_CACHE=y
++CONFIG_CMD_PSTORE=y
++CONFIG_CMD_PSTORE_MEM_ADDR=0x42ff0000
++CONFIG_CMD_UUID=y
++CONFIG_CMD_HASH=y
++CONFIG_CMD_SMC=y
++CONFIG_CMD_UBI=y
++CONFIG_CMD_UBI_RENAME=y
++CONFIG_OF_EMBED=y
++CONFIG_ENV_OVERWRITE=y
++CONFIG_ENV_IS_IN_UBI=y
++CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
++CONFIG_ENV_UBI_PART="ubi"
++CONFIG_ENV_UBI_VOLUME="ubootenv"
++CONFIG_ENV_UBI_VOLUME_REDUND="ubootenv2"
++CONFIG_SYS_RELOC_GD_ENV_ADDR=y
++CONFIG_USE_DEFAULT_ENV_FILE=y
++CONFIG_DEFAULT_ENV_FILE="routerich_ax3000_env"
++CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
++CONFIG_VERSION_VARIABLE=y
++CONFIG_NET_RANDOM_ETHADDR=y
++CONFIG_NETCONSOLE=y
++CONFIG_USE_IPADDR=y
++CONFIG_IPADDR="192.168.1.1"
++CONFIG_USE_SERVERIP=y
++CONFIG_SERVERIP="192.168.1.254"
++CONFIG_REGMAP=y
++CONFIG_SYSCON=y
++CONFIG_BUTTON=y
++CONFIG_BUTTON_GPIO=y
++CONFIG_CLK=y
++CONFIG_GPIO_HOG=y
++CONFIG_LED=y
++CONFIG_LED_BLINK=y
++CONFIG_LED_GPIO=y
++# CONFIG_MMC is not set
++CONFIG_MTD=y
++CONFIG_DM_MTD=y
++CONFIG_MTD_SPI_NAND=y
++CONFIG_MTD_UBI_FASTMAP=y
++CONFIG_PHY_FIXED=y
++CONFIG_MEDIATEK_ETH=y
++CONFIG_PHY=y
++CONFIG_PHY_MTK_TPHY=y
++CONFIG_PINCTRL=y
++CONFIG_PINCONF=y
++CONFIG_PINCTRL_MT7981=y
++CONFIG_POWER_DOMAIN=y
++CONFIG_MTK_POWER_DOMAIN=y
++CONFIG_DM_REGULATOR=y
++CONFIG_DM_REGULATOR_FIXED=y
++CONFIG_DM_REGULATOR_GPIO=y
++CONFIG_RAM=y
++CONFIG_DM_SERIAL=y
++CONFIG_MTK_SERIAL=y
++CONFIG_SPI=y
++CONFIG_DM_SPI=y
++CONFIG_MTK_SPIM=y
++CONFIG_ZSTD=y
++CONFIG_HEXDUMP=y
++CONFIG_LMB_MAX_REGIONS=64
+--- /dev/null
++++ b/arch/arm/dts/mt7981-routerich_ax3000.dts
+@@ -0,0 +1,187 @@
++// SPDX-License-Identifier: GPL-2.0
++/*
++ * Copyright (c) 2022 MediaTek Inc.
++ * Author: Sam Shih <sam.shih at mediatek.com>
++ */
++
++/dts-v1/;
++#include "mt7981.dtsi"
++#include <dt-bindings/gpio/gpio.h>
++#include <dt-bindings/input/linux-event-codes.h>
++
++/ {
++ #address-cells = <1>;
++ #size-cells = <1>;
++ model = "Routerich AX3000";
++ compatible = "routerich,ax3000", "mediatek,mt7981";
++
++ chosen {
++ stdout-path = &uart0;
++ tick-timer = &timer0;
++ };
++
++ memory at 40000000 {
++ device_type = "memory";
++ reg = <0x40000000 0x10000000>;
++ };
++
++ keys {
++ compatible = "gpio-keys";
++
++ button-0 {
++ label = "mesh";
++ linux,code = <BTN_0>;
++ gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
++ };
++
++ button-1 {
++ label = "reset";
++ linux,code = <KEY_RESTART>;
++ gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
++ };
++ };
++
++ leds {
++ compatible = "gpio-leds";
++
++ led-0 {
++ label = "red:wlan5g";
++ gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
++ };
++
++ led-1 {
++ label = "red:wan";
++ gpios = <&gpio 6 GPIO_ACTIVE_HIGH>;
++ };
++
++ led-2 {
++ label = "blue:power";
++ gpios = <&gpio 7 GPIO_ACTIVE_LOW>;
++ };
++
++ led-3 {
++ label = "blue:lan1";
++ gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
++ };
++
++ led-4 {
++ label = "blue:lan2";
++ gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
++ };
++
++ led-5 {
++ label = "blue:lan3";
++ gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
++ };
++
++ led-6 {
++ label = "blue:wan";
++ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
++ };
++
++ led-7 {
++ label = "blue:wlan2g";
++ gpios = <&gpio 34 GPIO_ACTIVE_LOW>;
++ };
++
++ led-8 {
++ label = "blue:mesh";
++ gpios = <&gpio 35 GPIO_ACTIVE_LOW>;
++ };
++ };
++};
++
++&uart0 {
++ mediatek,force-highspeed;
++ status = "okay";
++};
++
++ð {
++ status = "okay";
++ mediatek,gmac-id = <0>;
++ phy-mode = "2500base-x";
++ mediatek,switch = "mt7531";
++ reset-gpios = <&gpio 39 GPIO_ACTIVE_HIGH>;
++
++ fixed-link {
++ speed = <2500>;
++ full-duplex;
++ };
++};
++
++&pinctrl {
++ spi_flash_pins: spi0-pins-func-1 {
++ mux {
++ function = "flash";
++ groups = "spi0", "spi0_wp_hold";
++ };
++
++ conf-pu {
++ pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
++ drive-strength = <MTK_DRIVE_8mA>;
++ bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
++ };
++
++ conf-pd {
++ pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
++ drive-strength = <MTK_DRIVE_8mA>;
++ bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
++ };
++ };
++};
++
++&spi0 {
++ #address-cells = <1>;
++ #size-cells = <0>;
++ pinctrl-names = "default";
++ pinctrl-0 = <&spi_flash_pins>;
++ status = "okay";
++ must_tx;
++ enhance_timing;
++ dma_ext;
++ ipm_design;
++ support_quad;
++ tick_dly = <2>;
++ sample_sel = <0>;
++
++ spi_nand at 0 {
++ compatible = "spi-nand";
++ reg = <0>;
++ spi-max-frequency = <52000000>;
++
++ partitions {
++ compatible = "fixed-partitions";
++ #address-cells = <1>;
++ #size-cells = <1>;
++
++ partition at 0 {
++ label = "bl2";
++ reg = <0x0 0x100000>;
++ };
++
++ partition at 100000 {
++ label = "uboot-env-orig";
++ reg = <0x100000 0x80000>;
++ };
++
++ partition at 160000 {
++ label = "Factory";
++ reg = <0x180000 0x200000>;
++ };
++
++ partition at 380000 {
++ label = "fip";
++ reg = <0x380000 0x200000>;
++ };
++
++ partition at 580000 {
++ label = "ubi";
++ reg = <0x580000 0x7a80000>;
++ };
++ };
++ };
++};
++
++&watchdog {
++ status = "disabled";
++};
+--- /dev/null
++++ b/routerich_ax3000_env
+@@ -0,0 +1,58 @@
++ipaddr=192.168.1.1
++serverip=192.168.1.254
++loadaddr=0x46000000
++console=earlycon=uart8250,mmio32,0x11002000 console=ttyS0
++bootcmd=run check_buttons ; if pstore check ; then run boot_recovery ; else run boot_ubi ; fi
++bootconf=config-1
++bootdelay=0
++bootfile=openwrt-mediatek-filogic-routerich_ax3000-ubootmod-initramfs-recovery.itb
++bootfile_bl2=openwrt-mediatek-filogic-routerich_ax3000-ubootmod-preloader.bin
++bootfile_fip=openwrt-mediatek-filogic-routerich_ax3000-ubootmod-bl31-uboot.fip
++bootfile_upg=openwrt-mediatek-filogic-routerich_ax3000-ubootmod-squashfs-sysupgrade.itb
++bootled_pwr=blue:power
++bootled_rec=blue:power
++bootmenu_confirm_return=askenv - Press ENTER to return to menu ; bootmenu 60
++bootmenu_default=0
++bootmenu_delay=0
++bootmenu_title= [0;34m( ( ( [1;39mOpenWrt[0;34m ) ) )
++bootmenu_0=Initialize environment.=run _firstboot
++bootmenu_0d=Run default boot command.=run boot_default
++bootmenu_1=Boot system via TFTP.=run boot_tftp ; run bootmenu_confirm_return
++bootmenu_2=Boot production system from NAND.=run boot_production ; run bootmenu_confirm_return
++bootmenu_3=Boot recovery system from NAND.=run boot_recovery ; run bootmenu_confirm_return
++bootmenu_4=Load production system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_production ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
++bootmenu_5=Load recovery system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_recovery ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
++bootmenu_6=[31mLoad BL31+U-Boot FIP via TFTP then write to NAND.[0m=run boot_tftp_write_fip ; run bootmenu_confirm_return
++bootmenu_7=[31mLoad BL2 preloader via TFTP then write to NAND.[0m=run boot_tftp_write_bl2 ; run bootmenu_confirm_return
++bootmenu_8=Reboot.=reset
++bootmenu_9=Reset all settings to factory defaults.=run reset_factory ; reset
++boot_first=if button reset ; then led $bootled_rec on ; run boot_default ; fi ; bootmenu
++boot_default=if env exists flag_recover ; then else run bootcmd ; fi ; run boot_recovery ; setenv replacevol 1 ; run boot_tftp_forever
++boot_production=led $bootled_pwr on ; run ubi_read_production && bootm $loadaddr#$bootconf ; led $bootled_pwr off
++boot_recovery=led $bootled_rec on ; run ubi_read_recovery && bootm $loadaddr#$bootconf ; led $bootled_rec off
++boot_ubi=run boot_production ; run boot_recovery ; run boot_tftp_forever
++boot_tftp_forever=led $bootled_rec on ; while true ; do run boot_tftp ; sleep 1 ; done
++boot_tftp_production=tftpboot $loadaddr $bootfile_upg && env exists replacevol && iminfo $loadaddr && run ubi_write_production ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
++boot_tftp_recovery=tftpboot $loadaddr $bootfile && env exists replacevol && iminfo $loadaddr && run ubi_write_recovery ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
++boot_tftp=tftpboot $loadaddr $bootfile && bootm $loadaddr#$bootconf
++boot_tftp_write_fip=tftpboot $loadaddr $bootfile_fip && run mtd_write_fip && run reset_factory
++boot_tftp_write_bl2=tftpboot $loadaddr $bootfile_bl2 && run mtd_write_bl2
++check_buttons=if button reset ; then run boot_tftp ; fi
++ethaddr_factory=mtd read Factory 0x40080000 0x0 0x20000 && env readmem -b ethaddr 0x40080004 0x6 ; setenv ethaddr_factory
++part_default=production
++part_recovery=recovery
++reset_factory=ubi part ubi ; mw $loadaddr 0x0 0x800 ; ubi write $loadaddr ubootenv 0x800 ; ubi write $loadaddr ubootenv2 0x800
++mtd_write_fip=mtd erase fip && mtd write fip $loadaddr
++mtd_write_bl2=mtd erase bl2 && mtd write bl2 $loadaddr
++ubi_create_env=ubi check ubootenv || ubi create ubootenv 0x100000 dynamic || run ubi_format ; ubi check ubootenv2 || ubi create ubootenv2 0x100000 dynamic || run ubi_format
++ubi_format=ubi detach ; mtd erase ubi && ubi part ubi ; reset
++ubi_prepare_rootfs=if ubi check rootfs_data ; then else if env exists rootfs_data_max ; then ubi create rootfs_data $rootfs_data_max dynamic || ubi create rootfs_data - dynamic ; else ubi create rootfs_data - dynamic ; fi ; fi
++ubi_read_production=ubi read $loadaddr fit && iminfo $loadaddr && run ubi_prepare_rootfs
++ubi_read_recovery=ubi check recovery && ubi read $loadaddr recovery
++ubi_remove_rootfs=ubi check rootfs_data && ubi remove rootfs_data
++ubi_write_production=ubi check fit && ubi remove fit ; run ubi_remove_rootfs ; ubi create fit $filesize dynamic && ubi write $loadaddr fit $filesize
++ubi_write_recovery=ubi check recovery && ubi remove recovery ; run ubi_remove_rootfs ; ubi create recovery $filesize dynamic && ubi write $loadaddr recovery $filesize
++_init_env=setenv _init_env ; run ubi_create_env ; saveenv ; saveenv
++_firstboot=setenv _firstboot ; run ethaddr_factory ; run _switch_to_menu ; run _init_env ; run boot_first
++_switch_to_menu=setenv _switch_to_menu ; setenv bootdelay 3 ; setenv bootmenu_delay 3 ; setenv bootmenu_0 $bootmenu_0d ; setenv bootmenu_0d ; run _bootmenu_update_title
++_bootmenu_update_title=setenv _bootmenu_update_title ; setenv bootmenu_title "$bootmenu_title [33m$ver[0m"
More information about the lede-commits
mailing list