[openwrt/openwrt] mediatek: filogic: add support for Cudy WR3000S v1
LEDE Commits
lede-commits at lists.infradead.org
Sat Nov 23 11:27:45 PST 2024
hauke pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/faf4b3e0f7a583a8fa1a65b302ac74457e48575f
commit faf4b3e0f7a583a8fa1a65b302ac74457e48575f
Author: David Ignjic <ignjic at gmail.com>
AuthorDate: Wed Nov 13 11:20:27 2024 +0100
mediatek: filogic: add support for Cudy WR3000S v1
Hardware
--------
MediaTek MT7981 WiSoC
256MB DDR3 RAM
128MB SPI-NAND (XMC XM25QH128C)
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
UART: 115200 8N1 3.3V
MAC:
LAN MAC: label mac
WAN MAC: label mac + 1
2.4G MAC: label mac
5G MAC: label mac + 1 with LA bit set
Installation
------------
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device + press reset pin. Keep pressing reset pin to enter the U-Boot shell.
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.88. Rename the image to "cudy3000s.bin"
4. Download and boot the OpenWrt initramfs image.
$ tftpboot 0x46000000 cudy3000s.bin; bootm 0x46000000
5. Transfer the OpenWrt sysupgrade image to the device using scp.
Install with sysupgrade.
Signed-off-by: David Ignjic <ignjic at gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16939
Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
---
.../linux/mediatek/dts/mt7981b-cudy-wr3000s-v1.dts | 283 +++++++++++++++++++++
.../etc/hotplug.d/ieee80211/11_fix_wifi_mac | 1 +
target/linux/mediatek/image/filogic.mk | 17 ++
3 files changed, 301 insertions(+)
diff --git a/target/linux/mediatek/dts/mt7981b-cudy-wr3000s-v1.dts b/target/linux/mediatek/dts/mt7981b-cudy-wr3000s-v1.dts
new file mode 100644
index 0000000000..a643969494
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7981b-cudy-wr3000s-v1.dts
@@ -0,0 +1,283 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+
+#include "mt7981.dtsi"
+
+/ {
+ model = "Cudy WR3000S v1";
+ compatible = "cudy,wr3000s-v1", "mediatek,mt7981-spim-snand-rfb";
+
+ aliases {
+ label-mac-device = &gmac0;
+ led-boot = &led_status;
+ led-failsafe = &led_status;
+ led-running = &led_status;
+ led-upgrade = &led_status;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&pio 1 GPIO_ACTIVE_LOW>;
+ };
+
+ wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&pio 0 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_status: led at 0 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+ };
+
+
+ led_internet {
+ function = LED_FUNCTION_WAN_ONLINE;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 11 GPIO_ACTIVE_LOW>;
+ };
+
+ led_wps {
+ function = LED_FUNCTION_WPS;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+ };
+
+ led_wlan2g {
+ function = LED_FUNCTION_WLAN_2GHZ;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 6 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ led_wlan5g {
+ function = LED_FUNCTION_WLAN_5GHZ;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 7 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+ð {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio_pins>;
+
+ status = "okay";
+
+ gmac0: mac at 0 {
+ compatible = "mediatek,eth-mac";
+ reg = <0>;
+ phy-mode = "2500base-x";
+
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&macaddr_bdinfo_de00 0>;
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+};
+
+&mdio_bus {
+ switch: switch at 1f {
+ compatible = "mediatek,mt7531";
+ reg = <31>;
+ reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&pio>;
+ interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
+ };
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_flash_pins>;
+ status = "okay";
+
+ spi_nand: flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-nand";
+ reg = <0>;
+ spi-max-frequency = <52000000>;
+
+ spi-cal-enable;
+ spi-cal-mode = "read-data";
+ spi-cal-datalen = <7>;
+ spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>;
+ spi-cal-addrlen = <5>;
+ spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;
+
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+ mediatek,nmbm;
+ mediatek,bmt-max-ratio = <1>;
+ mediatek,bmt-max-reserved-blocks = <64>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "BL2";
+ reg = <0x00000 0x0100000>;
+ read-only;
+ };
+
+ partition at 100000 {
+ label = "u-boot-env";
+ reg = <0x0100000 0x0080000>;
+ read-only;
+ };
+
+ factory: partition at 180000 {
+ label = "Factory";
+ reg = <0x180000 0x0200000>;
+ read-only;
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ eeprom_factory_0: eeprom at 0 {
+ reg = <0x0 0x1000>;
+ };
+ };
+ };
+
+ partition at 380000 {
+ label = "bdinfo";
+ reg = <0x380000 0x0040000>;
+ read-only;
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_bdinfo_de00: macaddr at de00 {
+ compatible = "mac-base";
+ reg = <0xde00 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+ };
+ };
+
+ partition at 3C0000 {
+ label = "FIP";
+ reg = <0x3C0000 0x0200000>;
+ read-only;
+ };
+
+ partition at 580000 {
+ label = "ubi";
+ reg = <0x5C0000 0x4000000>;
+ compatible = "linux,ubi";
+ };
+ };
+ };
+};
+
+&pio {
+ spi0_flash_pins: spi0-pins {
+ mux {
+ function = "spi";
+ groups = "spi0", "spi0_wp_hold";
+ };
+ conf-pu {
+ pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
+ };
+
+ conf-pd {
+ pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
+ };
+ };
+};
+
+&switch {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ label = "wan";
+
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&macaddr_bdinfo_de00 1>;
+ };
+
+ port at 1 {
+ reg = <1>;
+ label = "lan1";
+ };
+
+ port at 2 {
+ reg = <2>;
+ label = "lan2";
+ };
+
+ port at 3 {
+ reg = <3>;
+ label = "lan3";
+ };
+
+ port at 4 {
+ reg = <4>;
+ label = "lan4";
+ };
+
+ port at 6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+};
+
+&wifi {
+ status = "okay";
+ nvmem-cells = <&eeprom_factory_0>;
+ nvmem-cell-names = "eeprom";
+};
diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
index f87cc0646e..7402bfc71b 100644
--- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
+++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
@@ -81,6 +81,7 @@ case "$board" in
;;
cudy,ap3000outdoor-v1|\
cudy,m3000-v1|\
+ cudy,wr3000s-v1|\
cudy,wr3000-v1)
addr=$(mtd_get_mac_binary bdinfo 0xde00)
# Originally, phy0 is phy1 mac with LA bit set. However, this would conflict
diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk
index 072cae0d1f..f366a9b920 100644
--- a/target/linux/mediatek/image/filogic.mk
+++ b/target/linux/mediatek/image/filogic.mk
@@ -667,6 +667,23 @@ define Device/cudy_wr3000-v1
endef
TARGET_DEVICES += cudy_wr3000-v1
+define Device/cudy_wr3000s-v1
+ DEVICE_VENDOR := Cudy
+ DEVICE_MODEL := WR3000S
+ DEVICE_VARIANT := v1
+ DEVICE_DTS := mt7981b-cudy-wr3000s-v1
+ DEVICE_DTS_DIR := ../dts
+ SUPPORTED_DEVICES += R59
+ UBINIZE_OPTS := -E 5
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ IMAGE_SIZE := 65536k
+ KERNEL_IN_UBI := 1
+ IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+ DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware
+endef
+TARGET_DEVICES += cudy_wr3000s-v1
+
define Device/dlink_aquila-pro-ai-m30-a1
DEVICE_VENDOR := D-Link
DEVICE_MODEL := AQUILA PRO AI M30
More information about the lede-commits
mailing list