[openwrt/openwrt] mediatek: filogic: add support for Cudy RE3000 v1
LEDE Commits
lede-commits at lists.infradead.org
Thu Mar 7 13:18:00 PST 2024
hauke pushed a commit to openwrt/openwrt.git, branch openwrt-23.05:
https://git.openwrt.org/6f70e09a00740e6ffc941247a1ccf3483696cebd
commit 6f70e09a00740e6ffc941247a1ccf3483696cebd
Author: Robert Senderek <robert.senderek at 10g.pl>
AuthorDate: Fri Feb 16 14:04:40 2024 +0100
mediatek: filogic: add support for Cudy RE3000 v1
MT7981B /256MB /16MB SPI (XM25QH128C)
AX 2.4Ghz
AX 5Ghz 160Mhz wide
1Gbit LAN
OEM:
root at RE3000:~# ifconfig |grep HWaddr
br-lan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0 (label)
br-wan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
eth0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
ra0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
ra2 Link encap:Ethernet HWaddr 82:XX:XX:28:XX:X0
rax0 Link encap:Ethernet HWaddr 82:XX:XX:38:XX:X0
rax2 Link encap:Ethernet HWaddr 82:XX:XX:58:XX:X0
OpenWrt
root at OpenWrt:/# ifconfig |grep HW
br-lan Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
eth0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
phy0-ap0 Link encap:Ethernet HWaddr 80:XX:XX:08:XX:X0
phy1-ap0 Link encap:Ethernet HWaddr 82:XX:XX:08:XX:X1
tftp Installation via u-boot:
Connect TTL3.3V converter
connector is under the radiator Set speed 115200 8 N 1
Interrupt boot process by holding down-arrow key during boot then
>> 6. Load image
>> 0 - TFTP client (Default)
enter IP adresses and initramfs-kernel.bin
write to flash via sysupgrade or gui
Signed-off-by: Robert Senderek <robert.senderek at 10g.pl>
(cherry picked from commit e8f75973172749874afa13e4f746acd8cb515de2)
---
.../base-files/lib/preinit/05_set_preinit_iface | 1 +
.../linux/mediatek/dts/mt7981b-cudy-re3000-v1.dts | 221 +++++++++++++++++++++
.../filogic/base-files/etc/board.d/01_leds | 3 +
.../filogic/base-files/etc/board.d/02_network | 1 +
.../etc/hotplug.d/ieee80211/11_fix_wifi_mac | 5 +
.../filogic/base-files/lib/upgrade/platform.sh | 3 +-
target/linux/mediatek/image/filogic.mk | 19 ++
7 files changed, 252 insertions(+), 1 deletion(-)
diff --git a/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface b/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface
index fd39b3f65f..d45f20fe62 100644
--- a/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface
+++ b/target/linux/mediatek/base-files/lib/preinit/05_set_preinit_iface
@@ -4,6 +4,7 @@ set_preinit_iface() {
ip link set eth1 up
ifname=eth1
;;
+ cudy,re3000-v1|\
ubnt,unifi-6-lr|\
zyxel,nwa50ax-pro)
ip link set eth0 up
diff --git a/target/linux/mediatek/dts/mt7981b-cudy-re3000-v1.dts b/target/linux/mediatek/dts/mt7981b-cudy-re3000-v1.dts
new file mode 100644
index 0000000000..4025e5aaa3
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7981b-cudy-re3000-v1.dts
@@ -0,0 +1,221 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "mt7981.dtsi"
+
+/ {
+ model = "Cudy RE3000 v1";
+ compatible = "cudy,re3000-v1", "mediatek,mt7981";
+
+ aliases {
+ serial0 = &uart0;
+ label-mac-device = &gmac1;
+ led-boot = &led_status;
+ led-failsafe = &led_status;
+ led-running = &led_status;
+ led-upgrade = &led_status;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&pio 1 GPIO_ACTIVE_LOW>;
+ };
+
+ wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&pio 0 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_status: led at 0 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+ };
+
+ led at 1 {
+ label = "red:wifi5";
+ gpios = <&pio 7 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ led at 2 {
+ label = "white:wifi2";
+ gpios = <&pio 6 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ led at 3 {
+ function = LED_FUNCTION_LAN;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+ };
+
+ led at 4 {
+ function = LED_FUNCTION_WPS;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&pio 11 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+ð {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio_pins>;
+ status = "okay";
+
+ gmac1: mac at 1 {
+ compatible = "mediatek,eth-mac";
+ reg = <1>;
+ phy-mode = "gmii";
+ phy-handle = <&int_gbe_phy>;
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&macaddr_bdinfo_de00 0>;
+ };
+};
+
+&mdio_bus {
+ switch: switch at 1f {
+ compatible = "mediatek,mt7531";
+ reg = <31>;
+ reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&spi0 {
+ status = "disabled";
+};
+
+&spi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_flash_pins>;
+ status = "okay";
+
+ flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+
+ spi-max-frequency = <25000000>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 00000 {
+ label = "BL2";
+ reg = <0x00000 0x40000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "u-boot-env";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ factory: partition at 50000 {
+ label = "Factory";
+ reg = <0x50000 0x10000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ eeprom_factory_0: eeprom at 0 {
+ reg = <0x0 0x1000>;
+ };
+ };
+ };
+
+ bdinfo: partition at 60000 {
+ label = "bdinfo";
+ reg = <0x60000 0x10000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_bdinfo_de00: macaddr at de00 {
+ compatible = "mac-base";
+ reg = <0xde00 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+ };
+ };
+
+ partition at 70000 {
+ label = "FIP";
+ reg = <0x70000 0x80000>;
+ read-only;
+ };
+
+ partition at f0000 {
+ compatible = "denx,fit";
+ label = "firmware";
+ reg = <0xf0000 0xf10000>;
+ };
+ };
+ };
+};
+
+&pio {
+ spi2_flash_pins: spi2-pins {
+ mux {
+ function = "spi";
+ groups = "spi2", "spi2_wp_hold";
+ };
+
+ conf-pu {
+ pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
+ drive-strength = <8>;
+ bias-pull-up = <103>;
+ };
+
+ conf-pd {
+ pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
+ drive-strength = <8>;
+ bias-pull-down = <103>;
+ };
+ };
+};
+
+&wifi {
+ status = "okay";
+ nvmem-cells = <&eeprom_factory_0>;
+ nvmem-cell-names = "eeprom";
+};
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
index 75c8fcda9b..96793e39cd 100644
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
@@ -12,6 +12,9 @@ confiabits,mt7981)
ucidef_set_led_netdev "lan3" "lan3" "blue:lan-3" "lan3" "link tx rx"
ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan" "link tx rx"
;;
+cudy,re3000-v1)
+ ucidef_set_led_netdev "lan" "lan" "green:lan" "eth0" "link tx rx"
+ ;;
cudy,wr3000-v1)
ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan"
;;
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
index a48fbbc79c..566a5ca82f 100644
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
@@ -58,6 +58,7 @@ mediatek_setup_interfaces()
mercusys,mr90x-v1)
ucidef_set_interfaces_lan_wan "lan0 lan1 lan2" eth1
;;
+ cudy,re3000-v1|\
netgear,wax220|\
ubnt,unifi-6-plus|\
zyxel,nwa50ax-pro)
diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
index e6378dd498..3441b41861 100644
--- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
+++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
@@ -57,6 +57,11 @@ case "$board" in
esac
[ "$PHYNBR" = "1" ] && echo "$addr" > /sys${DEVPATH}/macaddress
;;
+ cudy,re3000-v1)
+ addr=$(mtd_get_mac_binary bdinfo 0xde00)
+ [ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress
+ [ "$PHYNBR" = "1" ] && macaddr_setbit_la $(macaddr_add $addr 1) > /sys${DEVPATH}/macaddress
+ ;;
cudy,wr3000-v1)
addr=$(mtd_get_mac_binary bdinfo 0xde00)
# Originally, phy0 is phy1 mac with LA bit set. However, this would conflict
diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
index 9b3ebe92f1..25cbf98f33 100755
--- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
+++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
@@ -106,7 +106,8 @@ platform_do_upgrade() {
;;
esac
;;
- cudy,wr3000-v1)
+ cudy,wr3000-v1|\
+ cudy,re3000-v1)
default_do_upgrade "$1"
;;
glinet,gl-mt6000)
diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk
index 7daac6a1fa..5598a70aca 100644
--- a/target/linux/mediatek/image/filogic.mk
+++ b/target/linux/mediatek/image/filogic.mk
@@ -298,6 +298,25 @@ define Device/confiabits_mt7981
endef
TARGET_DEVICES += confiabits_mt7981
+define Device/cudy_re3000-v1
+ DEVICE_VENDOR := Cudy
+ DEVICE_MODEL := RE3000
+ DEVICE_VARIANT := v1
+ DEVICE_DTS := mt7981b-cudy-re3000-v1
+ DEVICE_DTS_DIR := ../dts
+ DEVICE_DTS_LOADADDR := 0x47000000
+ IMAGES := sysupgrade.bin
+ IMAGE_SIZE := 15424k
+ SUPPORTED_DEVICES += R36
+ KERNEL := kernel-bin | lzma | \
+ fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
+ KERNEL_INITRAMFS := kernel-bin | lzma | \
+ fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
+ IMAGE/sysupgrade.bin := append-kernel | pad-to 128k | append-rootfs | pad-rootfs | check-size | append-metadata
+ DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
+endef
+TARGET_DEVICES += cudy_re3000-v1
+
define Device/cudy_wr3000-v1
DEVICE_VENDOR := Cudy
DEVICE_MODEL := WR3000
More information about the lede-commits
mailing list