[openwrt/openwrt] ramips: mt7621: add support for Wodesys WD-R1802U
LEDE Commits
lede-commits at lists.infradead.org
Sun Jul 28 11:21:42 PDT 2024
hauke pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/5d0ccaf67cd3bb732dc15a53f9f080910ce73e66
commit 5d0ccaf67cd3bb732dc15a53f9f080910ce73e66
Author: Rani Hod <rani.hod at gmail.com>
AuthorDate: Sat Jun 15 17:27:42 2024 +0300
ramips: mt7621: add support for Wodesys WD-R1802U
This commit adds support for a dual-band AX1800 wall plug manufactured
by Shenzhen Century Xinyang Tech Co., Ltd.
CPU: Mediatek MT7621A (2 cores, 4 threads)
RAM: 256i MiB DDR3 (Samsung K4B2G1646F-BCNB)
ROM: 16 MiB SPI NOR (Winbond W25Q128JVPQ)
Wired: one gigabit RJ45 port (with green/yellow non-GPIO LEDs)
WiFi: Mediatek MT7905DAN + MT7975DN (DBDC 2x 2T2R)
Ant.: four 2 dBi external antennas (two 2.4GHz, two 5 GHz)
GPIO: tri-color status LED (GPIO 13, 14, 16);
reset button (GPIO 18)
Power: 12V 2-pin JST-XH on main PCB
110/220V AC to 12V1A DC on auxiliary PCB
UART: 115200 8n1, SMD pads available on the PCB as J4
pinout is [3v3] (Rx) (Tx) (Gnd)
MAC: 1C:BF:CE:xx:xx:xx (2.4 GHz, label)
1C:BF:CE:xx:xx:xx + 1 (ethernet [1])
1C:BF:CE:xx:xx:xx + 2 (5 GHz)
Original firmware is LEDE Reboot 17.01-SNAPSHOT (kernel 4.4.198)
with a few custom packages and a non-LuCI web interface.
Telnet and SSH are enabled, requiring an unknown root password [2].
Root password is also needed to access the router via UART console,
but passwordless telnet can be enabled via a trivial web exploit [3]
and then the root password can be removed by editing `/etc/shadow`.
Installation: First upload `sysupgrade` binary via web interface at
`http://192.168.188.1/settings.shtml` and wait until getting back to
the home screen (select network to extend). The installation fails
since the original firmware uses `swconfig` and recent versions of
OpenWrt use DSA. However, the sysupgrade file is uploaded correctly
and stored at `/tmp/upgrade.bin`, so it can be written to flash via
the web exploit [4] (both `mtd -r write` and `sysupgrade -Fn` work
fine). Passwordless telnet/ssh is not needed for installation.
Alternatively, use u-boot menu to load image via TFTP.
Notes:
- Device model in LEDE is "MediaTek MT7621 RFB (802.11ax,SNOR)".
- It is sold under several names, among them are Wodesys WD-R1802U,
Fenvi F-AX1802U, and EDUP EP-2971; the Wodesys brand was selected
since it is referenced in `/etc/banner` and `/etc/hosts`, and the
PCB is marked "WD518A V1.0".
- Instead of a standard ethernet transformer, the PCB has a few tiny
SMD coils.
[1] Original firmware sets ethernet MAC to 1C:BF:CE:E7:62:1D based on
offset `0x3fff4` in the Factory partition; since this is the same
MAC for all units, whereas WiFi MACs stored at offsets 0x6 and 0xc
are unique, it was decided to use <label MAC + 1> for ethernet.
[2] root:$1$7rmMiPJj$91iv9LWhfkZE/t7aCBdo.0:18388:0:99999:7:::
[3] curl -X POST http://192.168.188.1/cgi-bin/adm.cgi \
-d page=Lang -d langType="en;killall telnetd;telnetd -l /bin/sh"
[4] curl -X POST http://192.168.188.1/cgi-bin/adm.cgi \
-d page=Lang -d langType="en;mtd -r write /tmp/upgrade.bin firmware"
Signed-off-by: Rani Hod <rani.hod at gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15777
Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
---
.../linux/ramips/dts/mt7621_wodesys_wd-r1802u.dts | 153 +++++++++++++++++++++
target/linux/ramips/image/mt7621.mk | 11 ++
.../mt7621/base-files/etc/board.d/02_network | 1 +
3 files changed, 165 insertions(+)
diff --git a/target/linux/ramips/dts/mt7621_wodesys_wd-r1802u.dts b/target/linux/ramips/dts/mt7621_wodesys_wd-r1802u.dts
new file mode 100644
index 0000000000..f16d27e8d7
--- /dev/null
+++ b/target/linux/ramips/dts/mt7621_wodesys_wd-r1802u.dts
@@ -0,0 +1,153 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ compatible = "wodesys,wd-r1802u", "mediatek,mt7621-soc";
+ model = "Wodesys WD-R1802U";
+
+ aliases {
+ label-mac-device = &gmac0;
+ led-boot = &led_blue;
+ led-failsafe = &led_red;
+ led-running = &led_green;
+ led-upgrade = &led_blue;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ key-0 {
+ label = "reset";
+ gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ led_green: led-0 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ };
+
+ led_blue: led-1 {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ };
+
+ led_red: led-2 {
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ panic-indicator;
+ };
+ };
+};
+
+&gmac0 {
+ nvmem-cells = <&macaddr_factory_4 1>;
+ nvmem-cell-names = "mac-address";
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pcie1 {
+ wifi at 0,0 {
+ compatible = "mediatek,mt76";
+ reg = <0x0000 0 0 0 0>;
+ nvmem-cells = <&eeprom_factory_0>, <&precal_factory_e10>;
+ nvmem-cell-names = "eeprom", "precal";
+ mediatek,disable-radar-background;
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x00000 0x30000>;
+ read-only;
+ };
+
+ /* 0x30000-0x4ffff are unused
+ (flash contents is 0xff) */
+
+ partition at 50000 {
+ label = "factory";
+ reg = <0x50000 0x40000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ eeprom_factory_0: eeprom at 0 {
+ reg = <0x0 0xe00>;
+ };
+
+ macaddr_factory_4: macaddr at 4 { // wifi 2.4
+ compatible = "mac-base";
+ reg = <0x4 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ precal_factory_e10: precal at e10 {
+ reg = <0xe10 0x19c10>;
+ };
+ };
+ };
+
+ partition at 90000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x90000 0xf70000>;
+ };
+ };
+ };
+};
+
+&state_default {
+ gpio {
+ groups = "jtag", "wdt";
+ function = "gpio";
+ };
+};
+
+&switch0 {
+ ports {
+ port at 4 {
+ status = "okay";
+ label = "lan";
+ };
+ };
+};
+
+&xhci {
+ status = "disabled";
+};
diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk
index f8da28e9d6..5f6399eaed 100644
--- a/target/linux/ramips/image/mt7621.mk
+++ b/target/linux/ramips/image/mt7621.mk
@@ -2898,6 +2898,17 @@ define Device/winstars_ws-wn583a6
endef
TARGET_DEVICES += winstars_ws-wn583a6
+define Device/wodesys_wd-r1802u
+ $(Device/dsa-migration)
+ $(Device/uimage-lzma-loader)
+ IMAGE_SIZE := 15808k
+ DEVICE_VENDOR := Wodesys
+ DEVICE_MODEL := WD-R1802U
+ DEVICE_PACKAGES := kmod-mt7915-firmware -uboot-envtools
+ SUPPORTED_DEVICES += mt7621-rfb-ax-nor
+endef
+TARGET_DEVICES += wodesys_wd-r1802u
+
define Device/xiaomi_nand_separate
$(Device/nand)
$(Device/uimage-lzma-loader)
diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network
index accee97fb6..b7e3a49b43 100644
--- a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network
@@ -61,6 +61,7 @@ ramips_setup_interfaces()
ubnt,unifi-nanohd|\
yuncore,fap690|\
wavlink,wl-wn573hx1|\
+ wodesys,wd-r1802u|\
zyxel,nwa50ax|\
zyxel,nwa55axe)
ucidef_set_interface_lan "lan"
More information about the lede-commits
mailing list