[openwrt/openwrt] mediatek: filogic: add support for TP-LINK RE6000XD
LEDE Commits
lede-commits at lists.infradead.org
Thu Jul 4 13:15:58 PDT 2024
hauke pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/9e49593ff7f9860fc7901c17977ce2ec976adb4c
commit 9e49593ff7f9860fc7901c17977ce2ec976adb4c
Author: Dirk Buchwalder <buchwalder at posteo.de>
AuthorDate: Fri May 17 17:33:00 2024 +0200
mediatek: filogic: add support for TP-LINK RE6000XD
This commit adds support for TP-LINK RE6000XD.
The device is quite similar to the Mercusys MR90X V1,
except only 3 LAN ports and more LEDs.
So thanks to csharper2005 for doing all the groundwork.
Device specification
--------------------
SoC Type: MediaTek MT7986BLA, Cortex-A53, 64-bit
RAM: MediaTek MT7986BLA (512MB)
Flash: SPI NAND GigaDevice (128 MB)
Ethernet: MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8)
Ethernet: 1x2.5Gbe (LAN3 2.5Gbps), 2xGbE (LAN 1Gbps, LAN1,
LAN2)
WLAN 2g: MediaTek MT7975N, b/g/n/ax, MIMO 4x4
WLAN 5g: MediaTek MT7975P(N), a/n/ac/ax, MIMO 4x4
LEDs: 8 LEDs, 1 status blue, 2x WIFI blue, 2x signal
blue/red, 3 LAN blue gpio-controlled
Button: 2 (Reset, WPS)
USB ports: No
Power: 12 VDC, 2 A
Connector: Barrel
Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, ubi0
partition contain "seconduboot" (also U-Boot 2022.01-rc4)
Serial console (UART), unpopulated
---------------------
V
+-------+-------+-------+-------+
| +3.3V | GND | TX | RX |
+---+---+-------+-------+-------+
|
+--- Don't connect
Disassemble: rm the 2 screws at the bottom and the one at the backside.
un-clip the case starting at the edge above the LEDs.
Installation (UART)
-------------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
tftpboot openwrt-mediatek-filogic-tplink_re6000xd-initramfs-kernel.bin bootm
4. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Notice: while I was successfull at activating ssh (as described
here:
https://www.lisenet.com/2023/gaining-ssh-access-to-tp-link-re200-wi-fi-range-extender/)
Unfortunately I haven't found the correct root password.
Looks like they are using a static password
(md5crypt, salt + 21 characters) that is not the web
interface admin password.
The TP-LINK RE900XD looks like the very same device,
according to the pictures and the firmware.
But I haven't checked if the OpenWrt firmware works as well
on that device.
The second ubi partition (ubi1) is empty and there is no known
dual-partition mechanism, neither in u-boot nor in the stock firmware.
Signed-off-by: Dirk Buchwalder <buchwalder at posteo.de>
---
package/boot/uboot-envtools/files/mediatek_filogic | 3 +-
.../linux/mediatek/dts/mt7986b-tplink-re6000xd.dts | 298 +++++++++++++++++++++
.../filogic/base-files/etc/board.d/01_leds | 5 +
.../filogic/base-files/etc/board.d/02_network | 6 +-
.../etc/hotplug.d/firmware/11-mt76-caldata | 3 +-
.../etc/hotplug.d/ieee80211/11_fix_wifi_mac | 3 +-
.../base-files/lib/preinit/09_mount_cfg_part | 3 +-
.../base-files/lib/preinit/10_fix_eth_mac.sh | 3 +-
.../filogic/base-files/lib/upgrade/platform.sh | 3 +-
target/linux/mediatek/image/filogic.mk | 14 +
10 files changed, 334 insertions(+), 7 deletions(-)
diff --git a/package/boot/uboot-envtools/files/mediatek_filogic b/package/boot/uboot-envtools/files/mediatek_filogic
index c93fa2499b..0e30c489c9 100644
--- a/package/boot/uboot-envtools/files/mediatek_filogic
+++ b/package/boot/uboot-envtools/files/mediatek_filogic
@@ -102,7 +102,8 @@ glinet,gl-mt3000)
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x80000" "0x20000"
;;
mercusys,mr90x-v1|\
-routerich,ax3000)
+routerich,ax3000|\
+tplink,re6000xd)
local envdev=/dev/mtd$(find_mtd_index "u-boot-env")
ubootenv_add_uci_config "$envdev" "0x0" "0x20000" "0x20000" "1"
;;
diff --git a/target/linux/mediatek/dts/mt7986b-tplink-re6000xd.dts b/target/linux/mediatek/dts/mt7986b-tplink-re6000xd.dts
new file mode 100644
index 0000000000..44a5e21e7c
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7986b-tplink-re6000xd.dts
@@ -0,0 +1,298 @@
+// SPDX-License-Identifier: (GL-2.0 OR MIT)
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+#include "mt7986b.dtsi"
+
+/ {
+ compatible = "tplink,re6000xd", "mediatek,mt7986b";
+ model = "TP-Link RE6000XD";
+
+ aliases {
+ serial0 = &uart0;
+
+ led-boot = &led_status_blue;
+ led-failsafe = &led_status_blue;
+ led-running = &led_status_blue;
+ led-upgrade = &led_status_blue;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ reg = <0 0x40000000 0 0x20000000>;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&pio 7 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&pio 14 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_status_blue: power {
+ gpios = <&pio 15 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_STATUS;
+ panic-indicator;
+ function-enumerator = <0>;
+ };
+ wlan_2g {
+ gpios = <&pio 11 GPIO_ACTIVE_HIGH>;
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_WLAN_2GHZ;
+ linux,default-trigger = "phy0tpt";
+ };
+ wlan_5g {
+ gpios = <&pio 12 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_WLAN_5GHZ;
+ linux,default-trigger = "phy1tpt";
+ };
+ signal_blue {
+ gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_STATUS;
+ function-enumerator = <1>;
+ };
+ signal_red {
+ gpios = <&pio 19 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_STATUS;
+ function-enumerator = <2>;
+ };
+ lan1 {
+ gpios = <&pio 16 GPIO_ACTIVE_HIGH>;
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <0>;
+ };
+ lan2 {
+ gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <1>;
+ };
+ lan3 {
+ gpios = <&pio 18 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <2>;
+ };
+ };
+};
+
+&crypto {
+ status = "okay";
+};
+
+ð {
+ status = "okay";
+
+ gmac0: mac at 0 {
+ compatible = "mediatek,eth-mac";
+ reg = <0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+
+ gmac1: mac at 1 {
+ compatible = "mediatek,eth-mac";
+ reg = <1>;
+ phy-handle = <&phy6>;
+ phy-mode = "2500base-x";
+ };
+
+ mdio: mdio-bus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
+
+&mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&pio 6 GPIO_ACTIVE_LOW>;
+ reset-delay-us = <1500000>;
+ reset-post-delay-us = <1000000>;
+
+ /* LAN3 2.5Gbps phy
+ MaxLinear GPY211C0VC (SLNW8) */
+ phy6: phy at 6 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <6>;
+ };
+
+ switch: switch at 1f {
+ compatible = "mediatek,mt7531";
+ reg = <31>;
+ reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&switch {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ /* reorder LAN1 and LAN2 port to match the port order of the case
+ LAN1 - LAN2 - LAN3 (top to bottom of the case, no silkscreen)
+ */
+ /* LAN2 port */
+ port at 1 {
+ reg = <1>;
+ label = "lan2";
+ };
+
+ /* LAN1 port */
+ port at 2 {
+ reg = <2>;
+ label = "lan1";
+ };
+
+ port at 6 {
+ reg = <6>;
+ ethernet = <&gmac0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+};
+
+&pio {
+ spi_flash_pins: spi-flash-pins-33-to-38 {
+ mux {
+ function = "spi";
+ groups = "spi0", "spi0_wp_hold";
+ };
+ conf-pu {
+ pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
+ drive-strength = <8>;
+ mediatek,pull-up-adv = <0>; /* bias-disable */
+ };
+ conf-pd {
+ pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
+ drive-strength = <8>;
+ mediatek,pull-down-adv = <0>; /* bias-disable */
+ };
+ };
+
+ wf_2g_5g_pins: wf_2g_5g-pins {
+ mux {
+ function = "wifi";
+ groups = "wf_2g", "wf_5g";
+ };
+ conf {
+ pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+ "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+ "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+ "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+ "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+ "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+ "WF1_TOP_CLK", "WF1_TOP_DATA";
+ drive-strength = <4>;
+ };
+ };
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_flash_pins>;
+ status = "okay";
+
+ spi_nand_flash: flash at 0 {
+ compatible = "spi-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0>;
+
+ spi-max-frequency = <20000000>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+
+ partitions: partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "boot";
+ reg = <0x0 0x200000>;
+ read-only;
+ };
+
+ partition at 200000 {
+ label = "u-boot-env";
+ reg = <0x200000 0x100000>;
+ };
+
+ partition at 300000 {
+ label = "ubi0";
+ reg = <0x300000 0x3200000>;
+ };
+
+ partition at 3500000 {
+ label = "ubi1";
+ reg = <0x3500000 0x3200000>;
+ read-only;
+ };
+
+ partition at 6700000 {
+ label = "userconfig";
+ reg = <0x6700000 0x800000>;
+ read-only;
+ };
+
+ partition at 6f00000 {
+ label = "tp_data";
+ reg = <0x6f00000 0x400000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&trng {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+&wifi {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wf_2g_5g_pins>;
+};
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
index ca462d2005..99519cca7e 100644
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
@@ -96,6 +96,11 @@ wavlink,wl-wn586x3)
ucidef_set_led_netdev "lan-2" "lan-2" "blue:lan-2" "lan2" "link tx rx"
ucidef_set_led_netdev "wan" "wan" "blue:wan" "eth1" "link tx rx"
;;
+tplink,re6000xd)
+ ucidef_set_led_netdev "lan-1" "lan-1" "blue:lan-0" "lan1" "link tx rx"
+ ucidef_set_led_netdev "lan-2" "lan-2" "blue:lan-1" "lan2" "link tx rx"
+ ucidef_set_led_netdev "eth1" "lan-3" "blue:lan-2" "eth1" "link tx rx"
+ ;;
xiaomi,mi-router-wr30u-stock|\
xiaomi,mi-router-wr30u-ubootmod)
ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan" "link tx rx"
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
index 70b076dc9f..1a210810bc 100644
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
@@ -100,6 +100,9 @@ mediatek_setup_interfaces()
wavlink,wl-wn586x3)
ucidef_set_interfaces_lan_wan "lan1 lan2" eth1
;;
+ tplink,re6000xd)
+ ucidef_set_interface_lan "lan1 lan2 eth1"
+ ;;
xiaomi,mi-router-ax3000t|\
xiaomi,mi-router-ax3000t-ubootmod|\
xiaomi,mi-router-wr30u-stock|\
@@ -145,7 +148,8 @@ mediatek_setup_macs()
lan_mac=$(macaddr_add "$wan_mac" 1)
label_mac=$wan_mac
;;
- mercusys,mr90x-v1)
+ mercusys,mr90x-v1|\
+ tplink,re6000xd)
label_mac=$(get_mac_binary "/tmp/tp_data/default-mac" 0)
lan_mac=$label_mac
;;
diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata
index e0d1d93207..c6d9916b52 100644
--- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata
+++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata
@@ -41,7 +41,8 @@ case "$FIRMWARE" in
;;
"mediatek/mt7986_eeprom_mt7975_dual.bin")
case "$board" in
- mercusys,mr90x-v1)
+ mercusys,mr90x-v1|\
+ tplink,re6000xd)
ln -sf /tmp/tp_data/MT7986_EEPROM.bin \
/lib/firmware/$FIRMWARE
;;
diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
index 334d221e21..942facee87 100644
--- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
+++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
@@ -109,7 +109,8 @@ case "$board" in
jdcloud,re-cp-03)
[ "$PHYNBR" = "1" ] && mmc_get_mac_binary factory 0xa > /sys${DEVPATH}/macaddress
;;
- mercusys,mr90x-v1)
+ mercusys,mr90x-v1|\
+ tplink,re6000xd)
addr=$(get_mac_binary "/tmp/tp_data/default-mac" 0)
[ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress
[ "$PHYNBR" = "1" ] && macaddr_add $addr -1 > /sys${DEVPATH}/macaddress
diff --git a/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part b/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part
index 819df40d08..11e3b598af 100644
--- a/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part
+++ b/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part
@@ -12,7 +12,8 @@ mount_ubi_part() {
preinit_mount_cfg_part() {
case $(board_name) in
- mercusys,mr90x-v1)
+ mercusys,mr90x-v1|\
+ tplink,re6000xd)
mount_ubi_part "tp_data"
;;
*)
diff --git a/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh b/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh
index 2fe48b0ccf..fefca2327b 100644
--- a/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh
+++ b/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh
@@ -17,7 +17,8 @@ preinit_set_mac_address() {
ip link set dev eth0 address "$addr"
ip link set dev eth1 address "$addr"
;;
- mercusys,mr90x-v1)
+ mercusys,mr90x-v1|\
+ tplink,re6000xd)
addr=$(get_mac_binary "/tmp/tp_data/default-mac" 0)
ip link set dev eth1 address "$(macaddr_add $addr 1)"
;;
diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
index 7e105b1089..800e6bc5de 100755
--- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
+++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
@@ -142,7 +142,8 @@ platform_do_upgrade() {
CI_KERNPART="fit"
nand_do_upgrade "$1"
;;
- mercusys,mr90x-v1)
+ mercusys,mr90x-v1|\
+ tplink,re6000xd)
CI_UBIPART="ubi0"
nand_do_upgrade "$1"
;;
diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk
index 4db0cf2372..94b3098b3d 100644
--- a/target/linux/mediatek/image/filogic.mk
+++ b/target/linux/mediatek/image/filogic.mk
@@ -1085,6 +1085,20 @@ define Device/ruijie_rg-x60-pro
endef
TARGET_DEVICES += ruijie_rg-x60-pro
+define Device/tplink_re6000xd
+ DEVICE_VENDOR := TP-Link
+ DEVICE_MODEL := RE6000XD
+ DEVICE_DTS := mt7986b-tplink-re6000xd
+ DEVICE_DTS_DIR := ../dts
+ DEVICE_PACKAGES := kmod-mt7915e kmod-mt7986-firmware mt7986-wo-firmware
+ UBINIZE_OPTS := -E 5
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ IMAGE_SIZE := 51200k
+ IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+endef
+TARGET_DEVICES += tplink_re6000xd
+
define Device/tplink_tl-xdr-common
DEVICE_VENDOR := TP-Link
DEVICE_DTS_DIR := ../dts
More information about the lede-commits
mailing list