[openwrt/openwrt] mediatek: add support for Zbtlink ZBT-Z8103AX
LEDE Commits
lede-commits at lists.infradead.org
Wed Jul 3 01:24:24 PDT 2024
rmilecki pushed a commit to openwrt/openwrt.git, branch openwrt-23.05:
https://git.openwrt.org/77354213b74ef6a41a9d999817ddc889149c4a75
commit 77354213b74ef6a41a9d999817ddc889149c4a75
Author: Ian Oderon <ianoderon at gmail.com>
AuthorDate: Sat Dec 9 12:48:35 2023 +0800
mediatek: add support for Zbtlink ZBT-Z8103AX
Specifications:
SoC: MediaTek MT7981B
RAM: 256MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 3 LAN (Gigabit)
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND
No. of Antennas: 6
Note: Upon opening the router, only 5 antennas were connected
to the mainboard.
Led Layout:
Power-Mesh-5gwifi-WAN-LAN3-LAN2-LAN1-2gWiFi
Buttons:
Reset-Mesh
Installation:
A. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled (modified by the seller),
you can easily upgrade by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware, then flash the firmware
B. Through TFTP
Standard installation via UART:
1. Connect USB Serial Adapter to the UART, (NOTE: Don't connect the VCC pin).
2. Power on the router. Make sure that you can access your router via UART.
3. Restart the router then repeatedly press ctrl + c to skip default boot.
4. Type > bootmenu
5. Press '2' to select upgrade firmware
6. Press 'Y' on 'Run image after upgrading?'
7. Press '0' and hit 'enter' to select TFTP client (default)
8. Fill the U-Boot's IP address and TFTP server's IP address.
9. Finally, enter the 'firmware' filename.
Signed-off-by: Ian Oderon <ianoderon at gmail.com>
(cherry picked from commit 4300bc668819a77226b6e8ea079d3067f216e7bb)
---
package/boot/uboot-envtools/files/mediatek_filogic | 3 +-
.../mediatek/dts/mt7981b-zbtlink-zbt-z8103ax.dts | 269 +++++++++++++++++++++
.../filogic/base-files/etc/board.d/01_leds | 3 +
.../filogic/base-files/etc/board.d/02_network | 3 +-
.../etc/hotplug.d/ieee80211/11_fix_wifi_mac | 1 +
target/linux/mediatek/image/filogic.mk | 17 ++
6 files changed, 294 insertions(+), 2 deletions(-)
diff --git a/package/boot/uboot-envtools/files/mediatek_filogic b/package/boot/uboot-envtools/files/mediatek_filogic
index 48e59d6a6a..2cbb4bdc44 100644
--- a/package/boot/uboot-envtools/files/mediatek_filogic
+++ b/package/boot/uboot-envtools/files/mediatek_filogic
@@ -71,7 +71,8 @@ routerich,ax3000)
;;
cetron,ct3003|\
netgear,wax220|\
-zbtlink,zbt-z8102ax)
+zbtlink,zbt-z8102ax|\
+zbtlink,zbt-z8103ax)
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000"
;;
ubnt,unifi-6-plus)
diff --git a/target/linux/mediatek/dts/mt7981b-zbtlink-zbt-z8103ax.dts b/target/linux/mediatek/dts/mt7981b-zbtlink-zbt-z8103ax.dts
new file mode 100644
index 0000000000..2b079f5bca
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7981b-zbtlink-zbt-z8103ax.dts
@@ -0,0 +1,269 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include "mt7981.dtsi"
+
+/ {
+ model = "Zbtlink ZBT-Z8103AX";
+ compatible = "zbtlink,zbt-z8103ax", "mediatek,mt7981";
+
+ aliases {
+ serial0 = &uart0;
+ led-boot = &led_status_green;
+ led-failsafe = &led_status_red;
+ led-running = &led_status_green;
+ led-upgrade = &led_status_green;
+ label-mac-device = &gmac0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n8 loglevel=8";
+ };
+
+ memory {
+ reg = <0 0x40000000 0 0x10000000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ button-mesh {
+ label = "mesh";
+ linux,code = <BTN_0>;
+ linux,input-type = <EV_SW>;
+ gpios = <&pio 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ button-reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&pio 1 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-wan {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_WAN;
+ gpios = <&pio 8 GPIO_ACTIVE_LOW>;
+ };
+
+ led-status-blue {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&pio 23 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_status_green: led-status-green {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&pio 24 GPIO_ACTIVE_LOW>;
+ };
+
+ led_status_red: led-status-red {
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&pio 25 GPIO_ACTIVE_LOW>;
+ };
+
+ led-wlan2g {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_WLAN;
+ gpios = <&pio 34 GPIO_ACTIVE_LOW>;
+ function-enumerator = <0>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ led-wlan5g {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_WLAN;
+ gpios = <&pio 35 GPIO_ACTIVE_LOW>;
+ function-enumerator = <1>;
+ linux,default-trigger = "phy1tpt";
+ };
+ };
+};
+
+ð {
+ status = "okay";
+
+ gmac0: mac at 0 {
+ /* LAN */
+ compatible = "mediatek,eth-mac";
+ reg = <0>;
+ phy-mode = "2500base-x";
+
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&macaddr_factory_4 2>;
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+
+ gmac1: mac at 1 {
+ /* WAN */
+ compatible = "mediatek,eth-mac";
+ reg = <1>;
+ phy-mode = "gmii";
+ phy-handle = <&int_gbe_phy>;
+
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&macaddr_factory_4 3>;
+ };
+};
+
+&mdio_bus {
+ switch: switch at 1f {
+ compatible = "mediatek,mt7531";
+ reg = <31>;
+ reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&pio>;
+ interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
+ };
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_flash_pins>;
+ status = "okay";
+
+ spi_nand at 0 {
+ compatible = "spi-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0>;
+
+ spi-max-frequency = <52000000>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "bl2";
+ reg = <0x0000000 0x0100000>;
+ read-only;
+ };
+
+ partition at 100000 {
+ label = "u-boot-env";
+ reg = <0x100000 0x80000>;
+ };
+
+ partition at 180000 {
+ label = "Factory";
+ reg = <0x180000 0x200000>;
+ read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ eeprom_factory: eeprom at 0 {
+ reg = <0x0 0x1000>;
+ };
+
+ macaddr_factory_4: macaddr at 4 {
+ compatible = "mac-base";
+ reg = <0x4 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+ };
+ };
+
+ partition at 380000 {
+ label = "FIP";
+ reg = <0x380000 0x200000>;
+ read-only;
+ };
+
+ partition at 580000 {
+ label = "ubi";
+ reg = <0x580000 0x4000000>;
+ };
+ };
+ };
+};
+
+&switch {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ label = "lan1";
+ };
+
+ port at 1 {
+ reg = <1>;
+ label = "lan2";
+ };
+
+ port at 2 {
+ reg = <2>;
+ label = "lan3";
+ };
+
+ port at 6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+};
+
+&pio {
+ spi0_flash_pins: spi0-pins {
+ mux {
+ function = "spi";
+ groups = "spi0", "spi0_wp_hold";
+ };
+
+ conf-pu {
+ pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
+ };
+
+ conf-pd {
+ pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+&wifi {
+ status = "okay";
+ nvmem-cells = <&eeprom_factory>;
+ nvmem-cell-names = "eeprom";
+};
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
index 7d7d41362c..445cef120c 100644
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
@@ -44,6 +44,9 @@ xiaomi,redmi-router-ax6000-stock|\
xiaomi,redmi-router-ax6000-ubootmod)
ucidef_set_led_netdev "wan" "wan" "rgb:network" "wan"
;;
+zbtlink,zbt-z8103ax)
+ ucidef_set_led_netdev "wan" "wan" "green:wan" "eth1" "link tx rx"
+ ;;
zyxel_ex5601-t0-stock|\
zyxel,ex5601-t0-ubootmod)
ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth0" "link tx rx"
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
index 6885d5ff24..4a00b27927 100644
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
@@ -36,7 +36,8 @@ mediatek_setup_interfaces()
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 sfp2" "eth1 wan"
;;
cmcc,rax3000m|\
- h3c,magic-nx30-pro)
+ h3c,magic-nx30-pro|\
+ zbtlink,zbt-z8103ax)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" eth1
;;
cudy,tr3000-v1|\
diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
index a3d8b387db..2d9f9d73d3 100644
--- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
+++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
@@ -113,6 +113,7 @@ case "$board" in
;;
routerich,ax3000|\
zbtlink,zbt-z8102ax|\
+ zbtlink,zbt-z8103ax|\
zyxel,ex5601-t0|\
zyxel,ex5601-t0-ubootmod)
addr=$(mtd_get_mac_binary "Factory" 0x4)
diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk
index 09223f2d2f..5caac353ec 100644
--- a/target/linux/mediatek/image/filogic.mk
+++ b/target/linux/mediatek/image/filogic.mk
@@ -885,6 +885,23 @@ define Device/zbtlink_zbt-z8102ax
endef
TARGET_DEVICES += zbtlink_zbt-z8102ax
+define Device/zbtlink_zbt-z8103ax
+ DEVICE_VENDOR := Zbtlink
+ DEVICE_MODEL := ZBT-Z8103AX
+ DEVICE_DTS := mt7981b-zbtlink-zbt-z8103ax
+ DEVICE_DTS_DIR := ../dts
+ DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
+ KERNEL_IN_UBI := 1
+ UBINIZE_OPTS := -E 5
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ IMAGE_SIZE := 65536k
+ IMAGES += factory.bin
+ IMAGE/factory.bin := append-ubi | check-size $$(IMAGE_SIZE)
+ IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+endef
+TARGET_DEVICES += zbtlink_zbt-z8103ax
+
define Device/zyxel_ex5601-t0-stock
DEVICE_VENDOR := Zyxel
DEVICE_MODEL := EX5601-T0
More information about the lede-commits
mailing list