[openwrt/openwrt] qualcommax: ipq60xx: Add 8devices Mango DVK
LEDE Commits
lede-commits at lists.infradead.org
Wed Feb 21 12:42:33 PST 2024
robimarko pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/44168fda7800dfdd28c8d51fa92b4863f4fd6ea9
commit 44168fda7800dfdd28c8d51fa92b4863f4fd6ea9
Author: Mantas Pucka <mantas at 8devices.com>
AuthorDate: Mon Jan 22 11:28:32 2024 +0200
qualcommax: ipq60xx: Add 8devices Mango DVK
8devices Mango DVK is a single board computer / devkit for 8devices Mango
system-on-module (SoM).
Specifications:
* CPU: Qualcomm IPQ6010 Quad core Cortex-A53 1.8GHz
* RAM: 512 MB
* Storage:
* 32 MB serial NOR flash (on SoM)
* 256 MB parallel NAND flash (on DVK)
* Ethernet:
* 2x1G RJ45 ports(QCA8072 or QCA8075)
* 1x2.5G RJ45 port (QCA8081)
* 1xSFP (shares SGMII with QCA8081)
* Switch: Qualcomm Atheros IPQ6010
* WLAN:
* 2.4GHz: QCN5121 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: QCN5152 2x2 802.11a/n/ac/ax 1201 Mbps PHY rate
* USB:
* 1x USB3.0 Type-A port
* 1x USB2.0 available at mini PCIe slot
* PCIe: 1x mini PCIe slot 1xLane Gen3 (8GT/s)
* SD/eMMC (on a single shared bus - only one can be active):
* micro SD slot
* eMMC module connector
* LEDs:
* Green power led (not controllable)
* Green 2.4GHz radio led (GPIO 67)
* Green 5GHz radio led (GPIO 66)
* Buttons:
* 1x (WPS GPIO79) button
* GPIOs: 2.54mm header brings out 18 GPIOs (1.8V level)
* UART: 4-pin UART header (3.3V level)
* 115200 8N1, 3.3V-Tx-Rx-GND (3.3V is pin 1 close to boot-switch SW2)
* Power:
* PoE IN on 2.5G port (passive 24-48V)
* DC power terminal (12-58V)
Installation instructions:
Vendor image format is compatible with squashfs-sysupgrade image. Run:
sysupgrade -n -F openwrt-qualcommax-ipq60xx-8devices_mango-dvk-squashfs-sysupgrade.bin
Signed-off-by: Mantas Pucka <mantas at 8devices.com>
---
.../boot/uboot-envtools/files/qualcommax_ipq60xx | 22 ++
.../arch/arm64/boot/dts/qcom/ipq6010-mango-dvk.dts | 360 +++++++++++++++++++++
target/linux/qualcommax/image/ipq60xx.mk | 12 +
.../ipq60xx/base-files/etc/board.d/02_network | 28 ++
.../etc/hotplug.d/firmware/11-ath11-caldata | 20 ++
.../ipq60xx/base-files/lib/upgrade/platform.sh | 17 +
6 files changed, 459 insertions(+)
diff --git a/package/boot/uboot-envtools/files/qualcommax_ipq60xx b/package/boot/uboot-envtools/files/qualcommax_ipq60xx
new file mode 100644
index 0000000000..df19a30335
--- /dev/null
+++ b/package/boot/uboot-envtools/files/qualcommax_ipq60xx
@@ -0,0 +1,22 @@
+[ -e /etc/config/ubootenv ] && exit 0
+
+touch /etc/config/ubootenv
+
+. /lib/uboot-envtools.sh
+. /lib/functions.sh
+
+board=$(board_name)
+
+case "$board" in
+8devices,mango-dvk|\
+8devices,mango-dvk-sfp)
+ idx="$(find_mtd_index 0:APPSBLENV)"
+ [ -n "$idx" ] && \
+ ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x10000" "0x10000"
+ ;;
+esac
+
+config_load ubootenv
+config_foreach ubootenv_add_app_config
+
+exit 0
diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq6010-mango-dvk.dts b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq6010-mango-dvk.dts
new file mode 100644
index 0000000000..27247524a3
--- /dev/null
+++ b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq6010-mango-dvk.dts
@@ -0,0 +1,360 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include "ipq6018.dtsi"
+#include "ipq6018-cp-cpu.dtsi"
+#include "ipq6018-ess.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "8devices Mango-DVK";
+ compatible = "8devices,mango-dvk", "qcom,ipq6018";
+
+ aliases {
+ serial0 = &blsp1_uart3;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 79 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&led_pins>;
+ pinctrl-names = "default";
+
+ wlan5g {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_WLAN;
+ function-enumerator = <0>;
+ gpios = <&tlmm 66 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0radio";
+ };
+
+ wlan2g {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_WLAN;
+ function-enumerator = <1>;
+ gpios = <&tlmm 67 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy1radio";
+ };
+ };
+};
+
+&tlmm {
+ mdio_pins: mdio-pins {
+ mdc {
+ pins = "gpio64";
+ function = "mdc";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ mdio {
+ pins = "gpio65";
+ function = "mdio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+
+ spi_0_pins: spi-0-pins {
+ pins = "gpio38", "gpio39", "gpio40", "gpio41";
+ function = "blsp0_spi";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+
+ led_pins: led_pins {
+ leds {
+ pins = "gpio66", "gpio67";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+ };
+
+ sd_pins: sd_pins {
+ sd_cd {
+ pins = "gpio62";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+};
+
+&blsp1_uart3 {
+ pinctrl-0 = <&serial_3_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0>;
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "0:SBL1";
+ reg = <0x00000000 0x000c0000>;
+ };
+
+ partition at c0000 {
+ label = "0:MIBIB";
+ reg = <0x000c0000 0x00010000>;
+ };
+
+ partition at d0000 {
+ label = "0:QSEE";
+ reg = <0x000d0000 0x001a0000>;
+ };
+
+ partition at 270000 {
+ label = "0:DEVCFG";
+ reg = <0x00270000 0x00010000>;
+ };
+
+ partition at 280000 {
+ label = "0:RPM";
+ reg = <0x00280000 0x00020000>;
+ };
+
+ partition at 2a0000 {
+ label = "0:CDT";
+ reg = <0x002a0000 0x00010000>;
+ };
+
+ partition at 2b0000 {
+ label = "0:APPSBLENV";
+ reg = <0x002b0000 0x00010000>;
+ };
+
+ partition at 2c0000 {
+ label = "0:APPSBL";
+ reg = <0x002c0000 0x000a0000>;
+ };
+
+ partition at 360000 {
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ label = "0:ART";
+ reg = <0x00360000 0x00040000>;
+
+ macaddr_eth0: macaddr at 0 {
+ reg = <0x0 0x6>;
+ };
+
+ macaddr_eth1: macaddr at 6 {
+ reg = <0x6 0x6>;
+ };
+
+ macaddr_eth2: macaddr at c {
+ reg = <0xc 0x6>;
+ };
+ };
+
+ partition at 3a0000 {
+ label = "config";
+ reg = <0x003a0000 0x00040000>;
+ };
+
+ partition at 3e0000 {
+ label = "data";
+ reg = <0x003e0000 0x00100000>;
+ };
+
+ partition at 4e0000 {
+ label = "firmware";
+ compatible = "denx,fit";
+ reg = <0x004e0000 0x1b20000>;
+ };
+ };
+ };
+};
+
+&dp3 {
+ status = "okay";
+
+ phy-handle = <&qca8072_1>;
+ nvmem-cells = <&macaddr_eth1>;
+ nvmem-cell-names = "mac-address";
+ label = "lan2";
+};
+
+&dp4 {
+ status = "okay";
+
+ phy-handle = <&qca8072_0>;
+ nvmem-cells = <&macaddr_eth0>;
+ nvmem-cell-names = "mac-address";
+ label = "lan1";
+};
+
+&dp5 {
+ status = "okay";
+
+ phy-handle = <&qca8081>;
+ nvmem-cells = <&macaddr_eth2>;
+ nvmem-cell-names = "mac-address";
+ label = "wan";
+};
+
+&edma {
+ status = "okay";
+};
+
+&mdio {
+ status = "okay";
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ reset-gpios = <&tlmm 75 GPIO_ACTIVE_LOW>;
+ reset-delay-us = <10000>;
+ reset-post-delay-us = <50000>;
+
+ ethernet-phy-package at 0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "qcom,qca8075-package";
+ reg = <0>;
+
+ qcom,package-mode = "psgmii";
+
+ qca8072_0: ethernet-phy at 3 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <3>;
+ };
+
+ qca8072_1: ethernet-phy at 4 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <4>;
+ };
+ };
+
+ qca8081: ethernet-phy at 24 {
+ compatible = "ethernet-phy-id004d.d101";
+ reg = <24>;
+ reset-gpios = <&tlmm 77 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&sdhc_1 {
+ pinctrl-0 = <&sd_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ vqmmc-supply = <&ipq6018_l2>;
+ cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
+};
+
+&switch {
+ status = "okay";
+
+ switch_lan_bmp = <(ESS_PORT3 | ESS_PORT4)>;
+ switch_wan_bmp = <ESS_PORT5>;
+ switch_mac_mode = <MAC_MODE_PSGMII>;
+ switch_mac_mode1 = <MAC_MODE_SGMII_PLUS>;
+ port3_pcs_channel = <4>;
+
+ qcom,port_phyinfo {
+ port at 3 {
+ port_id = <3>;
+ phy_address = <4>;
+ };
+ port at 4 {
+ port_id = <4>;
+ phy_address = <3>;
+ };
+ port at 5 {
+ port_id = <5>;
+ phy_address = <24>;
+ port_mac_sel = "QGMAC_PORT";
+ };
+ };
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&qpic_nand {
+ status = "okay";
+
+ nand at 0 {
+ reg = <0>;
+
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ nand-bus-width = <8>;
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "nand_data";
+ reg = <0x0000000 0x10000000>;
+ };
+ };
+ };
+};
+
+&pcie_phy {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+ perst-gpio = <&tlmm 60 GPIO_ACTIVE_LOW>;
+};
+
+&wifi {
+ status = "okay";
+ qcom,ath11k-calibration-variant = "8devices-Mango";
+};
+
+&qusb_phy_1 {
+ status = "okay";
+};
+
+&usb2 {
+ status = "okay";
+};
+
+&qusb_phy_0 {
+ status = "okay";
+};
+
+&ssphy_0 {
+ status = "okay";
+};
+
+&usb3 {
+ status = "okay";
+};
diff --git a/target/linux/qualcommax/image/ipq60xx.mk b/target/linux/qualcommax/image/ipq60xx.mk
index e69de29bb2..00dead93ad 100644
--- a/target/linux/qualcommax/image/ipq60xx.mk
+++ b/target/linux/qualcommax/image/ipq60xx.mk
@@ -0,0 +1,12 @@
+define Device/8devices_mango-dvk
+ $(call Device/FitImageLzma)
+ DEVICE_VENDOR := 8devices
+ DEVICE_MODEL := Mango-DVK
+ IMAGE_SIZE := 27776k
+ BLOCKSIZE := 64k
+ SOC := ipq6010
+ SUPPORTED_DEVICES += 8devices,mango
+ IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | append-rootfs | pad-rootfs | check-size | append-metadata
+ DEVICE_PACKAGES := ipq-wifi-8devices_mango
+endef
+TARGET_DEVICES += 8devices_mango-dvk
diff --git a/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network b/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network
new file mode 100644
index 0000000000..081d894e1e
--- /dev/null
+++ b/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network
@@ -0,0 +1,28 @@
+#
+# Copyright (c) 2015 The Linux Foundation. All rights reserved.
+# Copyright (c) 2011-2015 OpenWrt.org
+#
+
+. /lib/functions/uci-defaults.sh
+. /lib/functions/system.sh
+
+ipq60xx_setup_interfaces()
+{
+ local board="$1"
+
+ case "$board" in
+ 8devices,mango-dvk)
+ ucidef_set_interfaces_lan_wan "lan1 lan2" "wan"
+ ;;
+ *)
+ echo "Unsupported hardware. Network interfaces not initialized"
+ ;;
+ esac
+}
+
+board_config_update
+board=$(board_name)
+ipq60xx_setup_interfaces $board
+board_config_flush
+
+exit 0
diff --git a/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11-caldata b/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11-caldata
new file mode 100644
index 0000000000..c14722c799
--- /dev/null
+++ b/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11-caldata
@@ -0,0 +1,20 @@
+#!/bin/sh
+
+[ -e /lib/firmware/$FIRMWARE ] && exit 0
+
+. /lib/functions/caldata.sh
+
+board=$(board_name)
+
+case "$FIRMWARE" in
+"ath11k/IPQ6018/hw1.0/cal-ahb-c000000.wifi.bin")
+ case "$board" in
+ 8devices,mango-dvk)
+ caldata_extract "0:ART" 0x1000 0x20000
+ ;;
+ esac
+ ;;
+*)
+ exit 1
+ ;;
+esac
diff --git a/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh b/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh
new file mode 100644
index 0000000000..3d3c17b3b9
--- /dev/null
+++ b/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh
@@ -0,0 +1,17 @@
+PART_NAME=firmware
+REQUIRE_IMAGE_METADATA=1
+
+RAMFS_COPY_BIN='fw_printenv fw_setenv head'
+RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
+
+platform_check_image() {
+ return 0;
+}
+
+platform_do_upgrade() {
+ case "$(board_name)" in
+ *)
+ default_do_upgrade "$1"
+ ;;
+ esac
+}
More information about the lede-commits
mailing list