[openwrt/openwrt] pistachio: remove 5.15 support
LEDE Commits
lede-commits at lists.infradead.org
Tue Apr 16 05:19:40 PDT 2024
wigyori pushed a commit to openwrt/openwrt.git, branch main:
https://git.openwrt.org/12137cb460e5ac0ef5924458c49822b776247179
commit 12137cb460e5ac0ef5924458c49822b776247179
Author: Zoltan HERPAI <wigyori at uid0.hu>
AuthorDate: Tue Apr 16 12:21:42 2024 +0200
pistachio: remove 5.15 support
Now that 6.1 is default, remove 5.15 support.
Signed-off-by: Zoltan HERPAI <wigyori at uid0.hu>
---
target/linux/pistachio/config-5.15 | 333 ---------------------
...maengine-img-mdc-Handle-early-status-read.patch | 68 -----
...spi-img-spfi-Implement-dual-and-quad-mode.patch | 198 ------------
...i-use-device-0-configuration-for-all-devi.patch | 64 ----
...g-spfi-RX-maximum-burst-size-for-DMA-is-8.patch | 59 ----
...pi-img-spfi-finish-every-transfer-cleanly.patch | 120 --------
...clk-pistachio-Fix-wrong-SDHost-card-speed.patch | 49 ---
...S-DTS-img-marduk-switch-mmc-to-1-bit-mode.patch | 47 ---
...mtd-nor-support-mtd-name-from-device-tree.patch | 54 ----
...01-MIPS-DTS-img-marduk-Add-SPI-NAND-flash.patch | 30 --
...DTS-img-marduk-Add-Cascoda-CA8210-6LoWPAN.patch | 43 ---
...-MIPS-DTS-img-marduk-Add-NXP-SC16IS752IPW.patch | 81 -----
...04-MIPS-DTS-img-marduk-Add-partition-name.patch | 27 --
.../905-MIPS-DTS-img-marduk-Add-led-aliases.patch | 27 --
14 files changed, 1200 deletions(-)
diff --git a/target/linux/pistachio/config-5.15 b/target/linux/pistachio/config-5.15
deleted file mode 100644
index c16a0c4551..0000000000
--- a/target/linux/pistachio/config-5.15
+++ /dev/null
@@ -1,333 +0,0 @@
-CONFIG_ARCH_32BIT_OFF_T=y
-CONFIG_ARCH_HIBERNATION_POSSIBLE=y
-CONFIG_ARCH_KEEP_MEMBLOCK=y
-CONFIG_ARCH_MMAP_RND_BITS_MAX=15
-CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MAX=15
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_SD=y
-# CONFIG_BOARD_INGENIC is not set
-CONFIG_BOARD_SCACHE=y
-CONFIG_BUILTIN_DTB=y
-CONFIG_CEVT_R4K=y
-CONFIG_CLKSRC_MIPS_GIC=y
-CONFIG_CLKSRC_PISTACHIO=y
-CONFIG_CLOCKSOURCE_WATCHDOG=y
-CONFIG_CLONE_BACKWARDS=y
-CONFIG_COMMON_CLK=y
-CONFIG_COMMON_CLK_PISTACHIO=y
-CONFIG_COMPAT_32BIT_TIME=y
-CONFIG_CONNECTOR=y
-CONFIG_CPU_GENERIC_DUMP_TLB=y
-CONFIG_CPU_HAS_DIEI=y
-CONFIG_CPU_HAS_PREFETCH=y
-CONFIG_CPU_HAS_RIXI=y
-# CONFIG_CPU_HAS_SMARTMIPS is not set
-CONFIG_CPU_HAS_SYNC=y
-CONFIG_CPU_IDLE=y
-CONFIG_CPU_IDLE_GOV_LADDER=y
-CONFIG_CPU_IDLE_GOV_MENU=y
-CONFIG_CPU_LITTLE_ENDIAN=y
-# CONFIG_CPU_MICROMIPS is not set
-CONFIG_CPU_MIPS32=y
-# CONFIG_CPU_MIPS32_R1 is not set
-CONFIG_CPU_MIPS32_R2=y
-# CONFIG_CPU_MIPS32_R6 is not set
-# CONFIG_CPU_MIPS64_R1 is not set
-# CONFIG_CPU_MIPS64_R2 is not set
-# CONFIG_CPU_MIPS64_R6 is not set
-CONFIG_CPU_MIPSR2=y
-CONFIG_CPU_MIPSR2_IRQ_EI=y
-CONFIG_CPU_MIPSR2_IRQ_VI=y
-CONFIG_CPU_NEEDS_NO_SMARTMIPS_OR_MICROMIPS=y
-CONFIG_CPU_PM=y
-CONFIG_CPU_R4K_CACHE_TLB=y
-CONFIG_CPU_RMAP=y
-CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
-CONFIG_CPU_SUPPORTS_HIGHMEM=y
-CONFIG_CPU_SUPPORTS_MSA=y
-CONFIG_CRC16=y
-CONFIG_CRC_CCITT=y
-CONFIG_CRYPTO_CBC=y
-CONFIG_CRYPTO_CRC32C=y
-CONFIG_CRYPTO_DEFLATE=y
-CONFIG_CRYPTO_HASH_INFO=y
-CONFIG_CRYPTO_LIB_BLAKE2S_GENERIC=y
-CONFIG_CRYPTO_LIB_POLY1305_RSIZE=2
-CONFIG_CRYPTO_LIB_SHA256=y
-CONFIG_CRYPTO_LZO=y
-CONFIG_CRYPTO_MD5=y
-CONFIG_CRYPTO_RNG=y
-CONFIG_CRYPTO_RNG2=y
-CONFIG_CRYPTO_SHA1=y
-CONFIG_CRYPTO_SHA256=y
-CONFIG_CRYPTO_ZSTD=y
-CONFIG_CSRC_R4K=y
-CONFIG_DMADEVICES=y
-CONFIG_DMA_ENGINE=y
-CONFIG_DMA_NONCOHERENT=y
-CONFIG_DMA_OF=y
-CONFIG_DMA_VIRTUAL_CHANNELS=y
-CONFIG_DTC=y
-CONFIG_DWMAC_GENERIC=y
-CONFIG_EXT4_FS=y
-# CONFIG_FIT_IMAGE_FDT_BOSTON is not set
-# CONFIG_FIT_IMAGE_FDT_JAGUAR2 is not set
-# CONFIG_FIT_IMAGE_FDT_LUTON is not set
-CONFIG_FIT_IMAGE_FDT_MARDUK=y
-# CONFIG_FIT_IMAGE_FDT_NI169445 is not set
-# CONFIG_FIT_IMAGE_FDT_OCELOT is not set
-# CONFIG_FIT_IMAGE_FDT_SERVAL is not set
-# CONFIG_FIT_IMAGE_FDT_XILFPGA is not set
-CONFIG_FIXED_PHY=y
-CONFIG_FS_IOMAP=y
-CONFIG_FS_MBCACHE=y
-CONFIG_FS_POSIX_ACL=y
-CONFIG_FWNODE_MDIO=y
-CONFIG_FW_LOADER_PAGED_BUF=y
-CONFIG_GENERIC_ALLOCATOR=y
-CONFIG_GENERIC_ATOMIC64=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_CMOS_UPDATE=y
-CONFIG_GENERIC_CPU_AUTOPROBE=y
-CONFIG_GENERIC_FIND_FIRST_BIT=y
-CONFIG_GENERIC_GETTIMEOFDAY=y
-CONFIG_GENERIC_IOMAP=y
-CONFIG_GENERIC_IRQ_CHIP=y
-CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y
-CONFIG_GENERIC_IRQ_MIGRATION=y
-CONFIG_GENERIC_IRQ_SHOW=y
-CONFIG_GENERIC_LIB_ASHLDI3=y
-CONFIG_GENERIC_LIB_ASHRDI3=y
-CONFIG_GENERIC_LIB_CMPDI2=y
-CONFIG_GENERIC_LIB_LSHRDI3=y
-CONFIG_GENERIC_LIB_UCMPDI2=y
-CONFIG_GENERIC_PCI_IOMAP=y
-CONFIG_GENERIC_PHY=y
-CONFIG_GENERIC_PINCONF=y
-CONFIG_GENERIC_PINCTRL_GROUPS=y
-CONFIG_GENERIC_PINMUX_FUNCTIONS=y
-CONFIG_GENERIC_SCHED_CLOCK=y
-CONFIG_GENERIC_SMP_IDLE_THREAD=y
-CONFIG_GENERIC_TIME_VSYSCALL=y
-CONFIG_GPIOLIB_IRQCHIP=y
-CONFIG_GPIO_CDEV=y
-CONFIG_HANDLE_DOMAIN_IRQ=y
-CONFIG_HARDWARE_WATCHPOINTS=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT_MAP=y
-CONFIG_HOTPLUG_CPU=y
-CONFIG_HZ_PERIODIC=y
-CONFIG_I2C=y
-CONFIG_I2C_BOARDINFO=y
-CONFIG_I2C_IMG=y
-CONFIG_IMGPDC_WDT=y
-CONFIG_IMG_MDC_DMA=y
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_IRQCHIP=y
-CONFIG_IRQ_DOMAIN=y
-CONFIG_IRQ_DOMAIN_HIERARCHY=y
-CONFIG_IRQ_FORCED_THREADING=y
-CONFIG_IRQ_MIPS_CPU=y
-CONFIG_IRQ_WORK=y
-CONFIG_JBD2=y
-CONFIG_LEDS_GPIO=y
-CONFIG_LEDS_PWM=y
-# CONFIG_LEGACY_BOARD_OCELOT is not set
-# CONFIG_LEGACY_BOARD_SEAD3 is not set
-CONFIG_LIBFDT=y
-CONFIG_LOCK_DEBUGGING_SUPPORT=y
-CONFIG_LOG_BUF_SHIFT=18
-CONFIG_LZO_COMPRESS=y
-CONFIG_LZO_DECOMPRESS=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_MAGIC_SYSRQ_DEFAULT_ENABLE=0
-CONFIG_MDIO_BUS=y
-CONFIG_MDIO_DEVICE=y
-CONFIG_MDIO_DEVRES=y
-CONFIG_MEMFD_CREATE=y
-CONFIG_MFD_SYSCON=y
-CONFIG_MICREL_PHY=y
-CONFIG_MIGRATION=y
-CONFIG_MIPS=y
-CONFIG_MIPS_ASID_BITS=8
-CONFIG_MIPS_ASID_SHIFT=0
-CONFIG_MIPS_AUTO_PFN_OFFSET=y
-CONFIG_MIPS_CLOCK_VSYSCALL=y
-CONFIG_MIPS_CM=y
-CONFIG_MIPS_CMDLINE_DTB_EXTEND=y
-# CONFIG_MIPS_CMDLINE_FROM_BOOTLOADER is not set
-CONFIG_MIPS_CPC=y
-CONFIG_MIPS_CPS=y
-# CONFIG_MIPS_CPS_CPUIDLE is not set
-# CONFIG_MIPS_CPS_NS16550_BOOL is not set
-CONFIG_MIPS_CPS_PM=y
-CONFIG_MIPS_CPU_SCACHE=y
-CONFIG_MIPS_EBPF_JIT=y
-CONFIG_MIPS_GENERIC=y
-CONFIG_MIPS_GENERIC_KERNEL=y
-CONFIG_MIPS_GIC=y
-CONFIG_MIPS_L1_CACHE_SHIFT=7
-CONFIG_MIPS_L1_CACHE_SHIFT_7=y
-CONFIG_MIPS_LD_CAN_LINK_VDSO=y
-CONFIG_MIPS_MT=y
-CONFIG_MIPS_MT_FPAFF=y
-CONFIG_MIPS_MT_SMP=y
-CONFIG_MIPS_NO_APPENDED_DTB=y
-CONFIG_MIPS_NR_CPU_NR_MAP=4
-CONFIG_MIPS_PERF_SHARED_TC_COUNTERS=y
-CONFIG_MIPS_SPRAM=y
-CONFIG_MMC=y
-CONFIG_MMC_BLOCK=y
-CONFIG_MMC_DW=y
-# CONFIG_MMC_DW_BLUEFIELD is not set
-# CONFIG_MMC_DW_EXYNOS is not set
-# CONFIG_MMC_DW_HI3798CV200 is not set
-# CONFIG_MMC_DW_K3 is not set
-CONFIG_MMC_DW_PLTFM=y
-CONFIG_MODULES_USE_ELF_REL=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_NAND_CORE=y
-CONFIG_MTD_NAND_ECC=y
-CONFIG_MTD_SPI_NAND=y
-CONFIG_MTD_SPI_NOR=y
-CONFIG_MTD_SPI_NOR_USE_4K_SECTORS=y
-CONFIG_MTD_UBI=y
-CONFIG_MTD_UBI_BEB_LIMIT=20
-CONFIG_MTD_UBI_BLOCK=y
-CONFIG_MTD_UBI_FASTMAP=y
-CONFIG_MTD_UBI_WL_THRESHOLD=4096
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NET_FLOW_LIMIT=y
-CONFIG_NET_PTP_CLASSIFY=y
-CONFIG_NET_SELFTESTS=y
-CONFIG_NLS=y
-CONFIG_NO_EXCEPT_FILL=y
-CONFIG_NR_CPUS=4
-CONFIG_OF=y
-CONFIG_OF_ADDRESS=y
-CONFIG_OF_EARLY_FLATTREE=y
-CONFIG_OF_FLATTREE=y
-CONFIG_OF_GPIO=y
-CONFIG_OF_IRQ=y
-CONFIG_OF_KOBJ=y
-CONFIG_OF_MDIO=y
-CONFIG_PADATA=y
-CONFIG_PAGE_POOL=y
-CONFIG_PCI_DRIVERS_GENERIC=y
-CONFIG_PCS_XPCS=y
-CONFIG_PERF_USE_VMALLOC=y
-CONFIG_PGTABLE_LEVELS=2
-CONFIG_PHYLIB=y
-CONFIG_PHYLINK=y
-CONFIG_PHY_PISTACHIO_USB=y
-CONFIG_PINCTRL=y
-CONFIG_PINCTRL_PISTACHIO=y
-CONFIG_POWER_SUPPLY=y
-CONFIG_PPS=y
-CONFIG_PRINTK_TIME=y
-CONFIG_PROC_EVENTS=y
-CONFIG_PTP_1588_CLOCK=y
-CONFIG_PTP_1588_CLOCK_OPTIONAL=y
-CONFIG_PWM=y
-CONFIG_PWM_IMG=y
-CONFIG_PWM_SYSFS=y
-CONFIG_QUEUED_RWLOCKS=y
-CONFIG_QUEUED_SPINLOCKS=y
-CONFIG_RATIONAL=y
-CONFIG_REGMAP=y
-CONFIG_REGMAP_MMIO=y
-CONFIG_REGMAP_SPI=y
-CONFIG_REGULATOR=y
-CONFIG_REGULATOR_FIXED_VOLTAGE=y
-CONFIG_REGULATOR_GPIO=y
-CONFIG_RESET_CONTROLLER=y
-CONFIG_RESET_PISTACHIO=y
-CONFIG_RFS_ACCEL=y
-CONFIG_RPS=y
-CONFIG_SCHEDSTATS=y
-CONFIG_SCHED_INFO=y
-CONFIG_SCSI=y
-CONFIG_SCSI_COMMON=y
-CONFIG_SCSI_SPI_ATTRS=y
-CONFIG_SERIAL_8250_DW=y
-CONFIG_SERIAL_8250_DWLIB=y
-CONFIG_SERIAL_MCTRL_GPIO=y
-CONFIG_SERIAL_OF_PLATFORM=y
-CONFIG_SERIAL_SC16IS7XX=y
-CONFIG_SERIAL_SC16IS7XX_CORE=y
-# CONFIG_SERIAL_SC16IS7XX_I2C is not set
-CONFIG_SERIAL_SC16IS7XX_SPI=y
-CONFIG_SGL_ALLOC=y
-CONFIG_SG_POOL=y
-CONFIG_SMP=y
-CONFIG_SMP_UP=y
-CONFIG_SOCK_RX_QUEUE_MAPPING=y
-CONFIG_SPI=y
-CONFIG_SPI_IMG_SPFI=y
-CONFIG_SPI_MASTER=y
-CONFIG_SPI_MEM=y
-CONFIG_SRAM=y
-CONFIG_SRCU=y
-CONFIG_STMMAC_ETH=y
-CONFIG_STMMAC_PLATFORM=y
-CONFIG_SWAP_IO_SPACE=y
-CONFIG_SWPHY=y
-CONFIG_SYNC_R4K=y
-CONFIG_SYSCTL_EXCEPTION_TRACE=y
-CONFIG_SYS_HAS_CPU_MIPS32_R1=y
-CONFIG_SYS_HAS_CPU_MIPS32_R2=y
-CONFIG_SYS_HAS_CPU_MIPS32_R6=y
-CONFIG_SYS_HAS_CPU_MIPS64_R1=y
-CONFIG_SYS_HAS_CPU_MIPS64_R2=y
-CONFIG_SYS_HAS_CPU_MIPS64_R6=y
-CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
-CONFIG_SYS_SUPPORTS_64BIT_KERNEL=y
-CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
-CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
-CONFIG_SYS_SUPPORTS_HIGHMEM=y
-CONFIG_SYS_SUPPORTS_HOTPLUG_CPU=y
-CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y
-CONFIG_SYS_SUPPORTS_MICROMIPS=y
-CONFIG_SYS_SUPPORTS_MIPS16=y
-CONFIG_SYS_SUPPORTS_MIPS_CPS=y
-CONFIG_SYS_SUPPORTS_MULTITHREADING=y
-CONFIG_SYS_SUPPORTS_RELOCATABLE=y
-CONFIG_SYS_SUPPORTS_SCHED_SMT=y
-CONFIG_SYS_SUPPORTS_SMARTMIPS=y
-CONFIG_SYS_SUPPORTS_SMP=y
-CONFIG_SYS_SUPPORTS_ZBOOT=y
-CONFIG_TARGET_ISA_REV=2
-CONFIG_TICK_CPU_ACCOUNTING=y
-CONFIG_TIMER_OF=y
-CONFIG_TIMER_PROBE=y
-CONFIG_TMPFS_POSIX_ACL=y
-CONFIG_TREE_RCU=y
-CONFIG_TREE_SRCU=y
-CONFIG_UBIFS_FS=y
-CONFIG_UHI_BOOT=y
-CONFIG_USB=y
-CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
-CONFIG_USB_COMMON=y
-CONFIG_USB_DWC2=y
-CONFIG_USB_DWC2_DUAL_ROLE=y
-CONFIG_USB_EHCI_HCD=y
-# CONFIG_USB_EHCI_HCD_PLATFORM is not set
-CONFIG_USB_GADGET=y
-CONFIG_USB_ROLE_SWITCH=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_SUPPORT=y
-CONFIG_USE_OF=y
-# CONFIG_VIRT_BOARD_RANCHU is not set
-CONFIG_WATCHDOG_CORE=y
-CONFIG_WEAK_ORDERING=y
-CONFIG_XPS=y
-CONFIG_XXHASH=y
-CONFIG_ZLIB_DEFLATE=y
-CONFIG_ZLIB_INFLATE=y
-CONFIG_ZSMALLOC=y
-# CONFIG_ZSMALLOC_STAT is not set
-CONFIG_ZSTD_COMPRESS=y
-CONFIG_ZSTD_DECOMPRESS=y
diff --git a/target/linux/pistachio/patches-5.15/101-dmaengine-img-mdc-Handle-early-status-read.patch b/target/linux/pistachio/patches-5.15/101-dmaengine-img-mdc-Handle-early-status-read.patch
deleted file mode 100644
index 031a4e3e5e..0000000000
--- a/target/linux/pistachio/patches-5.15/101-dmaengine-img-mdc-Handle-early-status-read.patch
+++ /dev/null
@@ -1,68 +0,0 @@
-From a2dd154377c9aa6ddda00d39b8c7c334e4fa16ff Mon Sep 17 00:00:00 2001
-From: Damien Horsley <damien.horsley at imgtec.com>
-Date: Tue, 22 Mar 2016 12:46:09 +0000
-Subject: dmaengine: img-mdc: Handle early status read
-
-It is possible that mdc_tx_status may be called before the first
-node has been read from memory.
-
-In this case, the residue value stored in the register is undefined.
-Return the transfer size instead.
-
-Signed-off-by: Damien Horsley <damien.horsley at imgtec.com>
----
- drivers/dma/img-mdc-dma.c | 40 ++++++++++++++++++++++++----------------
- 1 file changed, 24 insertions(+), 16 deletions(-)
-
---- a/drivers/dma/img-mdc-dma.c
-+++ b/drivers/dma/img-mdc-dma.c
-@@ -618,25 +618,33 @@ static enum dma_status mdc_tx_status(str
- (MDC_CMDS_PROCESSED_CMDS_DONE_MASK + 1);
-
- /*
-- * If the command loaded event hasn't been processed yet, then
-- * the difference above includes an extra command.
-+ * If the first node has not yet been read from memory,
-+ * the residue register value is undefined
- */
-- if (!mdesc->cmd_loaded)
-- cmds--;
-- else
-- cmds += mdesc->list_cmds_done;
--
-- bytes = mdesc->list_xfer_size;
-- ldesc = mdesc->list;
-- for (i = 0; i < cmds; i++) {
-- bytes -= ldesc->xfer_size + 1;
-- ldesc = ldesc->next_desc;
-- }
-- if (ldesc) {
-- if (residue != MDC_TRANSFER_SIZE_MASK)
-- bytes -= ldesc->xfer_size - residue;
-+ if (!mdesc->cmd_loaded && !cmds) {
-+ bytes = mdesc->list_xfer_size;
-+ } else {
-+ /*
-+ * If the command loaded event hasn't been processed yet, then
-+ * the difference above includes an extra command.
-+ */
-+ if (!mdesc->cmd_loaded)
-+ cmds--;
- else
-+ cmds += mdesc->list_cmds_done;
-+
-+ bytes = mdesc->list_xfer_size;
-+ ldesc = mdesc->list;
-+ for (i = 0; i < cmds; i++) {
- bytes -= ldesc->xfer_size + 1;
-+ ldesc = ldesc->next_desc;
-+ }
-+ if (ldesc) {
-+ if (residue != MDC_TRANSFER_SIZE_MASK)
-+ bytes -= ldesc->xfer_size - residue;
-+ else
-+ bytes -= ldesc->xfer_size + 1;
-+ }
- }
- }
- spin_unlock_irqrestore(&mchan->vc.lock, flags);
diff --git a/target/linux/pistachio/patches-5.15/102-spi-img-spfi-Implement-dual-and-quad-mode.patch b/target/linux/pistachio/patches-5.15/102-spi-img-spfi-Implement-dual-and-quad-mode.patch
deleted file mode 100644
index 83f21a5c0a..0000000000
--- a/target/linux/pistachio/patches-5.15/102-spi-img-spfi-Implement-dual-and-quad-mode.patch
+++ /dev/null
@@ -1,198 +0,0 @@
-From cd2a6af51553d38072cd31699b58d16ca6176ef5 Mon Sep 17 00:00:00 2001
-From: Ionela Voinescu <ionela.voinescu at imgtec.com>
-Date: Thu, 2 Feb 2017 16:46:14 +0000
-Subject: spi: img-spfi: Implement dual and quad mode
-
-For dual and quad modes to work the SPFI controller needs
-to have information about command/address/dummy bytes in the
-transaction register. This information is not relevant for
-single mode, and therefore it can have any value in the
-allowed range. Therefore, for any read or write transfers of less
-than 8 bytes (cmd = 1 byte, addr up to 7 bytes), SPFI will be
-configured, but not enabled (unless it is the last transfer in
-the queue). The transfer will be enabled by the subsequent tranfer.
-A pending transfer is determined by the content of the transaction
-register: if command part is set and tsize is not.
-
-This way we ensure that for dual and quad transactions
-the command request size will apear in the command/address part
-of the transaction register, while the data size will be in
-tsize, all data being sent/received in the same transaction (as
-set up in the transaction register).
-
-Signed-off-by: Ionela Voinescu <ionela.voinescu at imgtec.com>
-Signed-off-by: Ezequiel Garcia <ezequiel.garcia at imgtec.com>
----
- drivers/spi/spi-img-spfi.c | 96 ++++++++++++++++++++++++++++++++++++++++------
- 1 file changed, 85 insertions(+), 11 deletions(-)
-
---- a/drivers/spi/spi-img-spfi.c
-+++ b/drivers/spi/spi-img-spfi.c
-@@ -36,7 +36,8 @@
- #define SPFI_CONTROL_SOFT_RESET BIT(11)
- #define SPFI_CONTROL_SEND_DMA BIT(10)
- #define SPFI_CONTROL_GET_DMA BIT(9)
--#define SPFI_CONTROL_SE BIT(8)
-+#define SPFI_CONTROL_SE BIT(8)
-+#define SPFI_CONTROL_TX_RX BIT(1)
- #define SPFI_CONTROL_TMODE_SHIFT 5
- #define SPFI_CONTROL_TMODE_MASK 0x7
- #define SPFI_CONTROL_TMODE_SINGLE 0
-@@ -47,6 +48,10 @@
- #define SPFI_TRANSACTION 0x18
- #define SPFI_TRANSACTION_TSIZE_SHIFT 16
- #define SPFI_TRANSACTION_TSIZE_MASK 0xffff
-+#define SPFI_TRANSACTION_CMD_SHIFT 13
-+#define SPFI_TRANSACTION_CMD_MASK 0x7
-+#define SPFI_TRANSACTION_ADDR_SHIFT 10
-+#define SPFI_TRANSACTION_ADDR_MASK 0x7
-
- #define SPFI_PORT_STATE 0x1c
- #define SPFI_PORT_STATE_DEV_SEL_SHIFT 20
-@@ -83,6 +88,7 @@
- */
- #define SPFI_32BIT_FIFO_SIZE 64
- #define SPFI_8BIT_FIFO_SIZE 16
-+#define SPFI_DATA_REQUEST_MAX_SIZE 8
-
- struct img_spfi {
- struct device *dev;
-@@ -99,6 +105,8 @@ struct img_spfi {
- struct dma_chan *tx_ch;
- bool tx_dma_busy;
- bool rx_dma_busy;
-+
-+ bool complete;
- };
-
- static inline u32 spfi_readl(struct img_spfi *spfi, u32 reg)
-@@ -115,9 +123,11 @@ static inline void spfi_start(struct img
- {
- u32 val;
-
-- val = spfi_readl(spfi, SPFI_CONTROL);
-- val |= SPFI_CONTROL_SPFI_EN;
-- spfi_writel(spfi, val, SPFI_CONTROL);
-+ if (spfi->complete) {
-+ val = spfi_readl(spfi, SPFI_CONTROL);
-+ val |= SPFI_CONTROL_SPFI_EN;
-+ spfi_writel(spfi, val, SPFI_CONTROL);
-+ }
- }
-
- static inline void spfi_reset(struct img_spfi *spfi)
-@@ -130,12 +140,21 @@ static int spfi_wait_all_done(struct img
- {
- unsigned long timeout = jiffies + msecs_to_jiffies(50);
-
-+ if (!(spfi->complete))
-+ return 0;
-+
- while (time_before(jiffies, timeout)) {
- u32 status = spfi_readl(spfi, SPFI_INTERRUPT_STATUS);
-
- if (status & SPFI_INTERRUPT_ALLDONETRIG) {
- spfi_writel(spfi, SPFI_INTERRUPT_ALLDONETRIG,
- SPFI_INTERRUPT_CLEAR);
-+ /*
-+ * Disable SPFI for it not to interfere with
-+ * pending transactions
-+ */
-+ spfi_writel(spfi, spfi_readl(spfi, SPFI_CONTROL)
-+ & ~SPFI_CONTROL_SPFI_EN, SPFI_CONTROL);
- return 0;
- }
- cpu_relax();
-@@ -441,9 +460,32 @@ static void img_spfi_config(struct spi_m
- struct spi_transfer *xfer)
- {
- struct img_spfi *spfi = spi_master_get_devdata(spi->master);
-- u32 val, div;
-+ u32 val, div, transact;
-+ bool is_pending;
-
- /*
-+ * For read or write transfers of less than 8 bytes (cmd = 1 byte,
-+ * addr up to 7 bytes), SPFI will be configured, but not enabled
-+ * (unless it is the last transfer in the queue).The transfer will
-+ * be enabled by the subsequent transfer.
-+ * A pending transfer is determined by the content of the
-+ * transaction register: if command part is set and tsize
-+ * is not
-+ */
-+ transact = spfi_readl(spfi, SPFI_TRANSACTION);
-+ is_pending = ((transact >> SPFI_TRANSACTION_CMD_SHIFT) &
-+ SPFI_TRANSACTION_CMD_MASK) &&
-+ (!((transact >> SPFI_TRANSACTION_TSIZE_SHIFT) &
-+ SPFI_TRANSACTION_TSIZE_MASK));
-+
-+ /* If there are no pending transactions it's OK to soft reset */
-+ if (!is_pending) {
-+ /* Start the transaction from a known (reset) state */
-+ spfi_reset(spfi);
-+ }
-+
-+ /*
-+ * Before anything else, set up parameters.
- * output = spfi_clk * (BITCLK / 512), where BITCLK must be a
- * power of 2 up to 128
- */
-@@ -456,20 +498,52 @@ static void img_spfi_config(struct spi_m
- val |= div << SPFI_DEVICE_PARAMETER_BITCLK_SHIFT;
- spfi_writel(spfi, val, SPFI_DEVICE_PARAMETER(spi->chip_select));
-
-- spfi_writel(spfi, xfer->len << SPFI_TRANSACTION_TSIZE_SHIFT,
-- SPFI_TRANSACTION);
-+ if (!list_is_last(&xfer->transfer_list, &master->cur_msg->transfers) &&
-+ /*
-+ * For duplex mode (both the tx and rx buffers are !NULL) the
-+ * CMD, ADDR, and DUMMY byte parts of the transaction register
-+ * should always be 0 and therefore the pending transfer
-+ * technique cannot be used.
-+ */
-+ (xfer->tx_buf) && (!xfer->rx_buf) &&
-+ (xfer->len <= SPFI_DATA_REQUEST_MAX_SIZE) && !is_pending) {
-+ transact = (1 & SPFI_TRANSACTION_CMD_MASK) <<
-+ SPFI_TRANSACTION_CMD_SHIFT;
-+ transact |= ((xfer->len - 1) & SPFI_TRANSACTION_ADDR_MASK) <<
-+ SPFI_TRANSACTION_ADDR_SHIFT;
-+ spfi->complete = false;
-+ } else {
-+ spfi->complete = true;
-+ if (is_pending) {
-+ /* Keep setup from pending transfer */
-+ transact |= ((xfer->len & SPFI_TRANSACTION_TSIZE_MASK) <<
-+ SPFI_TRANSACTION_TSIZE_SHIFT);
-+ } else {
-+ transact = ((xfer->len & SPFI_TRANSACTION_TSIZE_MASK) <<
-+ SPFI_TRANSACTION_TSIZE_SHIFT);
-+ }
-+ }
-+ spfi_writel(spfi, transact, SPFI_TRANSACTION);
-
- val = spfi_readl(spfi, SPFI_CONTROL);
- val &= ~(SPFI_CONTROL_SEND_DMA | SPFI_CONTROL_GET_DMA);
-- if (xfer->tx_buf)
-+ /*
-+ * We set up send DMA for pending transfers also, as
-+ * those are always send transfers
-+ */
-+ if ((xfer->tx_buf) || is_pending)
- val |= SPFI_CONTROL_SEND_DMA;
-- if (xfer->rx_buf)
-+ if (xfer->tx_buf)
-+ val |= SPFI_CONTROL_TX_RX;
-+ if (xfer->rx_buf) {
- val |= SPFI_CONTROL_GET_DMA;
-+ val &= ~SPFI_CONTROL_TX_RX;
-+ }
- val &= ~(SPFI_CONTROL_TMODE_MASK << SPFI_CONTROL_TMODE_SHIFT);
-- if (xfer->tx_nbits == SPI_NBITS_DUAL &&
-+ if (xfer->tx_nbits == SPI_NBITS_DUAL ||
- xfer->rx_nbits == SPI_NBITS_DUAL)
- val |= SPFI_CONTROL_TMODE_DUAL << SPFI_CONTROL_TMODE_SHIFT;
-- else if (xfer->tx_nbits == SPI_NBITS_QUAD &&
-+ else if (xfer->tx_nbits == SPI_NBITS_QUAD ||
- xfer->rx_nbits == SPI_NBITS_QUAD)
- val |= SPFI_CONTROL_TMODE_QUAD << SPFI_CONTROL_TMODE_SHIFT;
- val |= SPFI_CONTROL_SE;
diff --git a/target/linux/pistachio/patches-5.15/104-spi-img-spfi-use-device-0-configuration-for-all-devi.patch b/target/linux/pistachio/patches-5.15/104-spi-img-spfi-use-device-0-configuration-for-all-devi.patch
deleted file mode 100644
index 2995b7dd88..0000000000
--- a/target/linux/pistachio/patches-5.15/104-spi-img-spfi-use-device-0-configuration-for-all-devi.patch
+++ /dev/null
@@ -1,64 +0,0 @@
-From 905ee06a9966113fe51d6bad1819759cb30fd0bd Mon Sep 17 00:00:00 2001
-From: Ionela Voinescu <ionela.voinescu at imgtec.com>
-Date: Tue, 9 Feb 2016 10:18:31 +0000
-Subject: spi: img-spfi: use device 0 configuration for all devices
-
-Given that we control the chip select line externally
-we can use only one parameter register (device 0 parameter
-register) and one set of configuration bits (port configuration
-bits for device 0) for all devices (all chip select lines).
-
-Signed-off-by: Ionela Voinescu <ionela.voinescu at imgtec.com>
----
- drivers/spi/spi-img-spfi.c | 23 ++++++++++++++++-------
- 1 file changed, 16 insertions(+), 7 deletions(-)
-
---- a/drivers/spi/spi-img-spfi.c
-+++ b/drivers/spi/spi-img-spfi.c
-@@ -429,18 +429,23 @@ static int img_spfi_prepare(struct spi_m
- struct img_spfi *spfi = spi_master_get_devdata(master);
- u32 val;
-
-+ /*
-+ * The chip select line is controlled externally so
-+ * we can use the CS0 configuration for all devices
-+ */
- val = spfi_readl(spfi, SPFI_PORT_STATE);
-+
-+ /* 0 for device selection */
- val &= ~(SPFI_PORT_STATE_DEV_SEL_MASK <<
- SPFI_PORT_STATE_DEV_SEL_SHIFT);
-- val |= msg->spi->chip_select << SPFI_PORT_STATE_DEV_SEL_SHIFT;
- if (msg->spi->mode & SPI_CPHA)
-- val |= SPFI_PORT_STATE_CK_PHASE(msg->spi->chip_select);
-+ val |= SPFI_PORT_STATE_CK_PHASE(0);
- else
-- val &= ~SPFI_PORT_STATE_CK_PHASE(msg->spi->chip_select);
-+ val &= ~SPFI_PORT_STATE_CK_PHASE(0);
- if (msg->spi->mode & SPI_CPOL)
-- val |= SPFI_PORT_STATE_CK_POL(msg->spi->chip_select);
-+ val |= SPFI_PORT_STATE_CK_POL(0);
- else
-- val &= ~SPFI_PORT_STATE_CK_POL(msg->spi->chip_select);
-+ val &= ~SPFI_PORT_STATE_CK_POL(0);
- spfi_writel(spfi, val, SPFI_PORT_STATE);
-
- return 0;
-@@ -492,11 +497,15 @@ static void img_spfi_config(struct spi_m
- div = DIV_ROUND_UP(clk_get_rate(spfi->spfi_clk), xfer->speed_hz);
- div = clamp(512 / (1 << get_count_order(div)), 1, 128);
-
-- val = spfi_readl(spfi, SPFI_DEVICE_PARAMETER(spi->chip_select));
-+ /*
-+ * The chip select line is controlled externally so
-+ * we can use the CS0 parameters for all devices
-+ */
-+ val = spfi_readl(spfi, SPFI_DEVICE_PARAMETER(0));
- val &= ~(SPFI_DEVICE_PARAMETER_BITCLK_MASK <<
- SPFI_DEVICE_PARAMETER_BITCLK_SHIFT);
- val |= div << SPFI_DEVICE_PARAMETER_BITCLK_SHIFT;
-- spfi_writel(spfi, val, SPFI_DEVICE_PARAMETER(spi->chip_select));
-+ spfi_writel(spfi, val, SPFI_DEVICE_PARAMETER(0));
-
- if (!list_is_last(&xfer->transfer_list, &master->cur_msg->transfers) &&
- /*
diff --git a/target/linux/pistachio/patches-5.15/105-spi-img-spfi-RX-maximum-burst-size-for-DMA-is-8.patch b/target/linux/pistachio/patches-5.15/105-spi-img-spfi-RX-maximum-burst-size-for-DMA-is-8.patch
deleted file mode 100644
index 5418503816..0000000000
--- a/target/linux/pistachio/patches-5.15/105-spi-img-spfi-RX-maximum-burst-size-for-DMA-is-8.patch
+++ /dev/null
@@ -1,59 +0,0 @@
-From 56466f505f58f44b69feb7eaed3b506842800456 Mon Sep 17 00:00:00 2001
-From: Ionela Voinescu <ionela.voinescu at imgtec.com>
-Date: Tue, 1 Mar 2016 17:49:45 +0000
-Subject: spi: img-spfi: RX maximum burst size for DMA is 8
-
-The depth of the FIFOs is 16 bytes. The DMA request line is tied
-to the half full/empty (depending on the use of the TX or RX FIFO)
-threshold. For the TX FIFO, if you set a burst size of 8 (equal to
-half the depth) the first burst goes into FIFO without any issues,
-but due the latency involved (the time the data leaves the DMA
-engine to the time it arrives at the FIFO), the DMA might trigger
-another burst of 8. But given that there is no space for 2 additonal
-bursts of 8, this would result in a failure. Therefore, we have to
-keep the burst size for TX to 4 to accomodate for an extra burst.
-
-For the read (RX) scenario, the DMA request line goes high when
-there is at least 8 entries in the FIFO (half full), and we can
-program the burst size to be 8 because the risk of accidental burst
-does not exist. The DMA engine will not trigger another read until
-the read data for all the burst it has sent out has been received.
-
-While here, move the burst size setting outside of the if/else branches
-as they have the same value for both 8 and 32 bit data widths.
-
-Signed-off-by: Ionela Voinescu <ionela.voinescu at imgtec.com>
----
- drivers/spi/spi-img-spfi.c | 6 ++----
- 1 file changed, 2 insertions(+), 4 deletions(-)
-
---- a/drivers/spi/spi-img-spfi.c
-+++ b/drivers/spi/spi-img-spfi.c
-@@ -338,12 +338,11 @@ static int img_spfi_start_dma(struct spi
- if (xfer->len % 4 == 0) {
- rxconf.src_addr = spfi->phys + SPFI_RX_32BIT_VALID_DATA;
- rxconf.src_addr_width = 4;
-- rxconf.src_maxburst = 4;
- } else {
- rxconf.src_addr = spfi->phys + SPFI_RX_8BIT_VALID_DATA;
- rxconf.src_addr_width = 1;
-- rxconf.src_maxburst = 4;
- }
-+ rxconf.src_maxburst = 8;
- dmaengine_slave_config(spfi->rx_ch, &rxconf);
-
- rxdesc = dmaengine_prep_slave_sg(spfi->rx_ch, xfer->rx_sg.sgl,
-@@ -362,12 +361,11 @@ static int img_spfi_start_dma(struct spi
- if (xfer->len % 4 == 0) {
- txconf.dst_addr = spfi->phys + SPFI_TX_32BIT_VALID_DATA;
- txconf.dst_addr_width = 4;
-- txconf.dst_maxburst = 4;
- } else {
- txconf.dst_addr = spfi->phys + SPFI_TX_8BIT_VALID_DATA;
- txconf.dst_addr_width = 1;
-- txconf.dst_maxburst = 4;
- }
-+ txconf.dst_maxburst = 4;
- dmaengine_slave_config(spfi->tx_ch, &txconf);
-
- txdesc = dmaengine_prep_slave_sg(spfi->tx_ch, xfer->tx_sg.sgl,
diff --git a/target/linux/pistachio/patches-5.15/106-spi-img-spfi-finish-every-transfer-cleanly.patch b/target/linux/pistachio/patches-5.15/106-spi-img-spfi-finish-every-transfer-cleanly.patch
deleted file mode 100644
index ea1f9f28cc..0000000000
--- a/target/linux/pistachio/patches-5.15/106-spi-img-spfi-finish-every-transfer-cleanly.patch
+++ /dev/null
@@ -1,120 +0,0 @@
-From 5fcca3fd4b621d7b5bdeca18d36dfc6ca6cfe383 Mon Sep 17 00:00:00 2001
-From: Ionela Voinescu <ionela.voinescu at imgtec.com>
-Date: Wed, 10 Aug 2016 11:42:26 +0100
-Subject: spi: img-spfi: finish every transfer cleanly
-
-Before this change, the interrupt status bit that signaled
-the end of a tranfers was cleared in the wait_all_done
-function. That functionality triggered issues for DMA
-duplex transactions where the wait function was called
-twice, in both the TX and RX callbacks.
-
-In order to fix the issue, clear all interrupt data bits
-at the end of a PIO transfer or at the end of both TX and RX
-duplex transfers, if the transfer is not a pending tranfer
-(command waiting for data). After that, the status register
-is checked for new incoming data or new data requests to be
-signaled. If SPFI finished cleanly, no new interrupt data
-bits should be set.
-
-Signed-off-by: Ionela Voinescu <ionela.voinescu at imgtec.com>
----
- drivers/spi/spi-img-spfi.c | 49 +++++++++++++++++++++++++++++++++-------------
- 1 file changed, 35 insertions(+), 14 deletions(-)
-
---- a/drivers/spi/spi-img-spfi.c
-+++ b/drivers/spi/spi-img-spfi.c
-@@ -79,6 +79,14 @@
- #define SPFI_INTERRUPT_SDE BIT(1)
- #define SPFI_INTERRUPT_SDTRIG BIT(0)
-
-+#define SPFI_INTERRUPT_DATA_BITS (SPFI_INTERRUPT_SDHF |\
-+ SPFI_INTERRUPT_SDFUL |\
-+ SPFI_INTERRUPT_GDEX32BIT |\
-+ SPFI_INTERRUPT_GDHF |\
-+ SPFI_INTERRUPT_GDFUL |\
-+ SPFI_INTERRUPT_ALLDONETRIG |\
-+ SPFI_INTERRUPT_GDEX8BIT)
-+
- /*
- * There are four parallel FIFOs of 16 bytes each. The word buffer
- * (*_32BIT_VALID_DATA) accesses all four FIFOs at once, resulting in an
-@@ -136,6 +144,23 @@ static inline void spfi_reset(struct img
- spfi_writel(spfi, 0, SPFI_CONTROL);
- }
-
-+static inline void spfi_finish(struct img_spfi *spfi)
-+{
-+ if (!(spfi->complete))
-+ return;
-+
-+ /* Clear data bits as all transfers(TX and RX) have finished */
-+ spfi_writel(spfi, SPFI_INTERRUPT_DATA_BITS, SPFI_INTERRUPT_CLEAR);
-+ if (spfi_readl(spfi, SPFI_INTERRUPT_STATUS) & SPFI_INTERRUPT_DATA_BITS) {
-+ dev_err(spfi->dev, "SPFI did not finish transfer cleanly.\n");
-+ spfi_reset(spfi);
-+ }
-+ /* Disable SPFI for it not to interfere with pending transactions */
-+ spfi_writel(spfi,
-+ spfi_readl(spfi, SPFI_CONTROL) & ~SPFI_CONTROL_SPFI_EN,
-+ SPFI_CONTROL);
-+}
-+
- static int spfi_wait_all_done(struct img_spfi *spfi)
- {
- unsigned long timeout = jiffies + msecs_to_jiffies(50);
-@@ -144,19 +169,9 @@ static int spfi_wait_all_done(struct img
- return 0;
-
- while (time_before(jiffies, timeout)) {
-- u32 status = spfi_readl(spfi, SPFI_INTERRUPT_STATUS);
--
-- if (status & SPFI_INTERRUPT_ALLDONETRIG) {
-- spfi_writel(spfi, SPFI_INTERRUPT_ALLDONETRIG,
-- SPFI_INTERRUPT_CLEAR);
-- /*
-- * Disable SPFI for it not to interfere with
-- * pending transactions
-- */
-- spfi_writel(spfi, spfi_readl(spfi, SPFI_CONTROL)
-- & ~SPFI_CONTROL_SPFI_EN, SPFI_CONTROL);
-+ if (spfi_readl(spfi, SPFI_INTERRUPT_STATUS) &
-+ SPFI_INTERRUPT_ALLDONETRIG)
- return 0;
-- }
- cpu_relax();
- }
-
-@@ -288,6 +303,8 @@ static int img_spfi_start_pio(struct spi
- }
-
- ret = spfi_wait_all_done(spfi);
-+ spfi_finish(spfi);
-+
- if (ret < 0)
- return ret;
-
-@@ -303,8 +320,10 @@ static void img_spfi_dma_rx_cb(void *dat
-
- spin_lock_irqsave(&spfi->lock, flags);
- spfi->rx_dma_busy = false;
-- if (!spfi->tx_dma_busy)
-+ if (!spfi->tx_dma_busy) {
-+ spfi_finish(spfi);
- spi_finalize_current_transfer(spfi->master);
-+ }
- spin_unlock_irqrestore(&spfi->lock, flags);
- }
-
-@@ -317,8 +336,10 @@ static void img_spfi_dma_tx_cb(void *dat
-
- spin_lock_irqsave(&spfi->lock, flags);
- spfi->tx_dma_busy = false;
-- if (!spfi->rx_dma_busy)
-+ if (!spfi->rx_dma_busy) {
-+ spfi_finish(spfi);
- spi_finalize_current_transfer(spfi->master);
-+ }
- spin_unlock_irqrestore(&spfi->lock, flags);
- }
-
diff --git a/target/linux/pistachio/patches-5.15/108-clk-pistachio-Fix-wrong-SDHost-card-speed.patch b/target/linux/pistachio/patches-5.15/108-clk-pistachio-Fix-wrong-SDHost-card-speed.patch
deleted file mode 100644
index 6fddbe269a..0000000000
--- a/target/linux/pistachio/patches-5.15/108-clk-pistachio-Fix-wrong-SDHost-card-speed.patch
+++ /dev/null
@@ -1,49 +0,0 @@
-From 3642843a06025ec333d7e92580cf52cb8db2a652 Mon Sep 17 00:00:00 2001
-From: Govindraj Raja <Govindraj.Raja at imgtec.com>
-Date: Fri, 8 Jan 2016 16:36:07 +0000
-Subject: clk: pistachio: Fix wrong SDHost card speed
-
-The SDHost currently clocks the card 4x slower than it
-should do, because there is fixed divide by 4 in the
-sdhost wrapper that is not present in the clock tree.
-To model this add a fixed divide by 4 clock node in
-the SDHost clock path.
-
-This will ensure the right clock frequency is selected when
-the mmc driver tries to configure frequency on card insert.
-
-Signed-off-by: Govindraj Raja <Govindraj.Raja at imgtec.com>
----
- drivers/clk/pistachio/clk-pistachio.c | 3 ++-
- include/dt-bindings/clock/pistachio-clk.h | 1 +
- 2 files changed, 3 insertions(+), 1 deletion(-)
-
---- a/drivers/clk/pistachio/clk-pistachio.c
-+++ b/drivers/clk/pistachio/clk-pistachio.c
-@@ -41,7 +41,7 @@ static struct pistachio_gate pistachio_g
- GATE(CLK_AUX_ADC_INTERNAL, "aux_adc_internal", "sys_internal_div",
- 0x104, 22),
- GATE(CLK_AUX_ADC, "aux_adc", "aux_adc_div", 0x104, 23),
-- GATE(CLK_SD_HOST, "sd_host", "sd_host_div", 0x104, 24),
-+ GATE(CLK_SD_HOST, "sd_host", "sd_host_div4", 0x104, 24),
- GATE(CLK_BT, "bt", "bt_div", 0x104, 25),
- GATE(CLK_BT_DIV4, "bt_div4", "bt_div4_div", 0x104, 26),
- GATE(CLK_BT_DIV8, "bt_div8", "bt_div8_div", 0x104, 27),
-@@ -51,6 +51,7 @@ static struct pistachio_gate pistachio_g
- static struct pistachio_fixed_factor pistachio_ffs[] __initdata = {
- FIXED_FACTOR(CLK_WIFI_DIV4, "wifi_div4", "wifi_pll", 4),
- FIXED_FACTOR(CLK_WIFI_DIV8, "wifi_div8", "wifi_pll", 8),
-+ FIXED_FACTOR(CLK_SDHOST_DIV4, "sd_host_div4", "sd_host_div", 4),
- };
-
- static struct pistachio_div pistachio_divs[] __initdata = {
---- a/include/dt-bindings/clock/pistachio-clk.h
-+++ b/include/dt-bindings/clock/pistachio-clk.h
-@@ -18,6 +18,7 @@
- /* Fixed-factor clocks */
- #define CLK_WIFI_DIV4 16
- #define CLK_WIFI_DIV8 17
-+#define CLK_SDHOST_DIV4 18
-
- /* Gate clocks */
- #define CLK_MIPS 32
diff --git a/target/linux/pistachio/patches-5.15/109-MIPS-DTS-img-marduk-switch-mmc-to-1-bit-mode.patch b/target/linux/pistachio/patches-5.15/109-MIPS-DTS-img-marduk-switch-mmc-to-1-bit-mode.patch
deleted file mode 100644
index faba23c5f1..0000000000
--- a/target/linux/pistachio/patches-5.15/109-MIPS-DTS-img-marduk-switch-mmc-to-1-bit-mode.patch
+++ /dev/null
@@ -1,47 +0,0 @@
-From 981c1d416af45eff207227aec106381ac23aac99 Mon Sep 17 00:00:00 2001
-From: Ian Pozella <Ian.Pozella at imgtec.com>
-Date: Mon, 20 Feb 2017 10:00:52 +0000
-Subject: MIPS: DTS: img: marduk: switch mmc to 1 bit mode
-
-The mmc block in Pistachio allows 1 to 8 data bits to be used.
-Marduk uses 4 bits allowing the upper 4 bits to be allocated
-to the Mikrobus ports. However these bits are still connected
-internally meaning the mmc block recieves signals on all data lines
-and seems the internal HW CRC checks get corrupted by this erroneous
-data.
-
-We cannot control what data is sent on these lines because they go
-to external ports. 1 bit mode does not exhibit the issue hence the
-safe default is to use this. If a user knows that in their use case
-they will not use the upper bits then they can set to 4 bit mode in
-order to improve performance.
-
-Also make sure that the upper 4 bits don't get allocated to the mmc
-driver (the default is to assign all 8 pins) so they can be allocated
-to other drivers. Allocating all 4 despite setting 1 bit mode as this
-matches what is there in hardware.
-
-Signed-off-by: Ian Pozella <Ian.Pozella at imgtec.com>
----
- arch/mips/boot/dts/img/pistachio_marduk.dts | 3 ++-
- 1 file changed, 2 insertions(+), 1 deletion(-)
-
---- a/arch/mips/boot/dts/img/pistachio_marduk.dts
-+++ b/arch/mips/boot/dts/img/pistachio_marduk.dts
-@@ -118,7 +118,7 @@
-
- &sdhost {
- status = "okay";
-- bus-width = <4>;
-+ bus-width = <1>;
- disable-wp;
- };
-
-@@ -128,6 +128,7 @@
-
- &pin_sdhost_data {
- drive-strength = <2>;
-+ pins = "mfio17", "mfio18", "mfio19", "mfio20";
- };
-
- &pwm {
diff --git a/target/linux/pistachio/patches-5.15/401-mtd-nor-support-mtd-name-from-device-tree.patch b/target/linux/pistachio/patches-5.15/401-mtd-nor-support-mtd-name-from-device-tree.patch
deleted file mode 100644
index 36f5331bd0..0000000000
--- a/target/linux/pistachio/patches-5.15/401-mtd-nor-support-mtd-name-from-device-tree.patch
+++ /dev/null
@@ -1,54 +0,0 @@
-From f32bc2aa01edcba2f2ed5db151cf183eac9ef919 Mon Sep 17 00:00:00 2001
-From: Abhimanyu Vishwakarma <Abhimanyu.Vishwakarma at imgtec.com>
-Date: Sat, 25 Feb 2017 16:42:50 +0000
-Subject: mtd: nor: support mtd name from device tree
-
-Signed-off-by: Abhimanyu Vishwakarma <Abhimanyu.Vishwakarma at imgtec.com>
----
- drivers/mtd/spi-nor/spi-nor.c | 8 +++++++-
- 1 file changed, 7 insertions(+), 1 deletion(-)
-
---- a/drivers/mtd/spi-nor/core.c
-+++ b/drivers/mtd/spi-nor/core.c
-@@ -3108,6 +3108,7 @@ int spi_nor_scan(struct spi_nor *nor, co
- struct device *dev = nor->dev;
- struct mtd_info *mtd = &nor->mtd;
- struct device_node *np = spi_nor_get_flash_node(nor);
-+ const char __maybe_unused *of_mtd_name = NULL;
- int ret;
- int i;
-
-@@ -3162,7 +3163,12 @@ int spi_nor_scan(struct spi_nor *nor, co
- if (ret)
- return ret;
-
-- if (!mtd->name)
-+#ifdef CONFIG_MTD_OF_PARTS
-+ of_property_read_string(np, "linux,mtd-name", &of_mtd_name);
-+#endif
-+ if (of_mtd_name)
-+ mtd->name = of_mtd_name;
-+ else if (!mtd->name)
- mtd->name = dev_name(dev);
- mtd->priv = nor;
- mtd->type = MTD_NORFLASH;
---- a/drivers/mtd/mtdcore.c
-+++ b/drivers/mtd/mtdcore.c
-@@ -870,6 +870,17 @@ out_error:
- */
- static void mtd_set_dev_defaults(struct mtd_info *mtd)
- {
-+#ifdef CONFIG_MTD_OF_PARTS
-+ const char __maybe_unused *of_mtd_name = NULL;
-+ struct device_node *np;
-+
-+ np = mtd_get_of_node(mtd);
-+ if (np && !mtd->name) {
-+ of_property_read_string(np, "linux,mtd-name", &of_mtd_name);
-+ if (of_mtd_name)
-+ mtd->name = of_mtd_name;
-+ } else
-+#endif
- if (mtd->dev.parent) {
- if (!mtd->owner && mtd->dev.parent->driver)
- mtd->owner = mtd->dev.parent->driver->owner;
diff --git a/target/linux/pistachio/patches-5.15/901-MIPS-DTS-img-marduk-Add-SPI-NAND-flash.patch b/target/linux/pistachio/patches-5.15/901-MIPS-DTS-img-marduk-Add-SPI-NAND-flash.patch
deleted file mode 100644
index 4b28f46833..0000000000
--- a/target/linux/pistachio/patches-5.15/901-MIPS-DTS-img-marduk-Add-SPI-NAND-flash.patch
+++ /dev/null
@@ -1,30 +0,0 @@
-From 0023c706f7e0f0f02bd48a63a2f3c04c839532ae Mon Sep 17 00:00:00 2001
-From: Hauke Mehrtens <hauke at hauke-m.de>
-Date: Sat, 15 Aug 2020 16:04:53 +0200
-Subject: [PATCH 901/904] MIPS: DTS: img: marduk: Add SPI NAND flash
-
-Add Gigadevice GD5F4GQ4UCYIGT SPI NAND flash to the device tree.
-
-The NAND flash chip is connected with quad SPI, but reading currently
-fails in quad SPI mode.
-
-Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
----
- arch/mips/boot/dts/img/pistachio_marduk.dts | 6 ++++++
- 1 file changed, 6 insertions(+)
-
---- a/arch/mips/boot/dts/img/pistachio_marduk.dts
-+++ b/arch/mips/boot/dts/img/pistachio_marduk.dts
-@@ -89,6 +89,12 @@
- reg = <0>;
- spi-max-frequency = <50000000>;
- };
-+
-+ flash at 1 {
-+ compatible = "spi-nand";
-+ reg = <1>;
-+ spi-max-frequency = <50000000>;
-+ };
- };
-
- &uart0 {
diff --git a/target/linux/pistachio/patches-5.15/902-MIPS-DTS-img-marduk-Add-Cascoda-CA8210-6LoWPAN.patch b/target/linux/pistachio/patches-5.15/902-MIPS-DTS-img-marduk-Add-Cascoda-CA8210-6LoWPAN.patch
deleted file mode 100644
index d4c4ccac53..0000000000
--- a/target/linux/pistachio/patches-5.15/902-MIPS-DTS-img-marduk-Add-Cascoda-CA8210-6LoWPAN.patch
+++ /dev/null
@@ -1,43 +0,0 @@
-From b7700154d75e8d7c9a2022f09c2d5430137606fa Mon Sep 17 00:00:00 2001
-From: Hauke Mehrtens <hauke at hauke-m.de>
-Date: Sat, 15 Aug 2020 16:05:25 +0200
-Subject: [PATCH 902/904] MIPS: DTS: img: marduk: Add Cascoda CA8210 6LoWPAN
-
-Add Cascoda CA8210 6LoWPAN controller to device tree.
-
-Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
----
- arch/mips/boot/dts/img/pistachio_marduk.dts | 22 +++++++++++++++++++++
- 1 file changed, 22 insertions(+)
-
---- a/arch/mips/boot/dts/img/pistachio_marduk.dts
-+++ b/arch/mips/boot/dts/img/pistachio_marduk.dts
-@@ -76,6 +76,28 @@
- VDD-supply = <&internal_dac_supply>;
- };
-
-+&spfi0 {
-+ status = "okay";
-+ pinctrl-0 = <&spim0_pins>, <&spim0_cs0_alt_pin>, <&spim0_cs2_alt_pin>, <&spim0_cs3_alt_pin>, <&spim0_cs4_alt_pin>;
-+ pinctrl-names = "default";
-+
-+ cs-gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>, <&gpio0 2 GPIO_ACTIVE_HIGH>,
-+ <&gpio1 12 GPIO_ACTIVE_HIGH>, <&gpio1 13 GPIO_ACTIVE_HIGH>;
-+
-+ ca8210: ca8210 at 0 {
-+ status = "okay";
-+ compatible = "cascoda,ca8210";
-+ reg = <0>;
-+ spi-max-frequency = <4000000>;
-+ spi-cpol;
-+ reset-gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
-+ irq-gpio = <&gpio2 12 GPIO_ACTIVE_HIGH>;
-+ extclock-enable;
-+ extclock-freq = <16000000>;
-+ extclock-gpio = <2>;
-+ };
-+};
-+
- &spfi1 {
- status = "okay";
-
diff --git a/target/linux/pistachio/patches-5.15/903-MIPS-DTS-img-marduk-Add-NXP-SC16IS752IPW.patch b/target/linux/pistachio/patches-5.15/903-MIPS-DTS-img-marduk-Add-NXP-SC16IS752IPW.patch
deleted file mode 100644
index b1070c3d30..0000000000
--- a/target/linux/pistachio/patches-5.15/903-MIPS-DTS-img-marduk-Add-NXP-SC16IS752IPW.patch
+++ /dev/null
@@ -1,81 +0,0 @@
-From ad4eba0c36ce8af6ab9ea1bc163e4c1ac7c271c3 Mon Sep 17 00:00:00 2001
-From: Hauke Mehrtens <hauke at hauke-m.de>
-Date: Sat, 15 Aug 2020 16:09:02 +0200
-Subject: [PATCH 903/904] MIPS: DTS: img: marduk: Add NXP SC16IS752IPW
-
-Add NXP SC16IS752IPW SPI-UART controller to device tree.
-
-This controller drives 2 UARTs and 7 LEDs on the board.
-
-Signed-off-by: Hauke Mehrtens <hauke at hauke-m.de>
----
- arch/mips/boot/dts/img/pistachio_marduk.dts | 51 +++++++++++++++++++++
- 1 file changed, 51 insertions(+)
-
---- a/arch/mips/boot/dts/img/pistachio_marduk.dts
-+++ b/arch/mips/boot/dts/img/pistachio_marduk.dts
-@@ -46,6 +46,46 @@
- regulator-max-microvolt = <1800000>;
- };
-
-+ /* EXT clock from ca8210 is fed to sc16is752 */
-+ ca8210_ext_clk: ca8210-ext-clk {
-+ compatible = "fixed-clock";
-+ #clock-cells = <0>;
-+ clock-frequency = <16000000>;
-+ clock-output-names = "ca8210_ext_clock";
-+ };
-+
-+ gpioleds {
-+ compatible = "gpio-leds";
-+ user1 {
-+ label = "marduk:red:user1";
-+ gpios = <&sc16is752 0 GPIO_ACTIVE_LOW>;
-+ };
-+ user2 {
-+ label = "marduk:red:user2";
-+ gpios = <&sc16is752 1 GPIO_ACTIVE_LOW>;
-+ };
-+ user3 {
-+ label = "marduk:red:user3";
-+ gpios = <&sc16is752 2 GPIO_ACTIVE_LOW>;
-+ };
-+ user4 {
-+ label = "marduk:red:user4";
-+ gpios = <&sc16is752 3 GPIO_ACTIVE_LOW>;
-+ };
-+ user5 {
-+ label = "marduk:red:user5";
-+ gpios = <&sc16is752 4 GPIO_ACTIVE_LOW>;
-+ };
-+ user6 {
-+ label = "marduk:red:user6";
-+ gpios = <&sc16is752 5 GPIO_ACTIVE_LOW>;
-+ };
-+ user7 {
-+ label = "marduk:red:user7";
-+ gpios = <&sc16is752 6 GPIO_ACTIVE_LOW>;
-+ };
-+ };
-+
- led-controller {
- compatible = "pwm-leds";
-
-@@ -96,6 +136,17 @@
- extclock-freq = <16000000>;
- extclock-gpio = <2>;
- };
-+
-+ sc16is752: sc16is752 at 1 {
-+ compatible = "nxp,sc16is752";
-+ reg = <1>;
-+ clocks = <&ca8210_ext_clk>;
-+ spi-max-frequency = <4000000>;
-+ interrupt-parent = <&gpio0>;
-+ interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
-+ gpio-controller;
-+ #gpio-cells = <2>;
-+ };
- };
-
- &spfi1 {
diff --git a/target/linux/pistachio/patches-5.15/904-MIPS-DTS-img-marduk-Add-partition-name.patch b/target/linux/pistachio/patches-5.15/904-MIPS-DTS-img-marduk-Add-partition-name.patch
deleted file mode 100644
index 490027a702..0000000000
--- a/target/linux/pistachio/patches-5.15/904-MIPS-DTS-img-marduk-Add-partition-name.patch
+++ /dev/null
@@ -1,27 +0,0 @@
-From ff0e950b605047bf50d470023e0fb2fc2003a0f0 Mon Sep 17 00:00:00 2001
-From: Ian Pozella <Ian.Pozella at imgtec.com>
-Date: Mon, 20 Feb 2017 10:38:07 +0000
-Subject: [PATCH 904/904] MIPS: DTS: img: marduk: Add partition name
-
-Signed-off-by: Ian Pozella <Ian.Pozella at imgtec.com>
----
- arch/mips/boot/dts/img/pistachio_marduk.dts | 2 ++
- 1 file changed, 2 insertions(+)
-
---- a/arch/mips/boot/dts/img/pistachio_marduk.dts
-+++ b/arch/mips/boot/dts/img/pistachio_marduk.dts
-@@ -161,12 +161,14 @@
- compatible = "spansion,s25fl016k", "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <50000000>;
-+ linux,mtd-name = "spi-nor";
- };
-
- flash at 1 {
- compatible = "spi-nand";
- reg = <1>;
- spi-max-frequency = <50000000>;
-+ linux,mtd-name = "spi-nand";
- };
- };
-
diff --git a/target/linux/pistachio/patches-5.15/905-MIPS-DTS-img-marduk-Add-led-aliases.patch b/target/linux/pistachio/patches-5.15/905-MIPS-DTS-img-marduk-Add-led-aliases.patch
deleted file mode 100644
index 8c03ddeea2..0000000000
--- a/target/linux/pistachio/patches-5.15/905-MIPS-DTS-img-marduk-Add-led-aliases.patch
+++ /dev/null
@@ -1,27 +0,0 @@
---- a/arch/mips/boot/dts/img/pistachio_marduk.dts
-+++ b/arch/mips/boot/dts/img/pistachio_marduk.dts
-@@ -19,6 +19,11 @@
- ethernet0 = &enet;
- spi0 = &spfi0;
- spi1 = &spfi1;
-+
-+ led-boot = &led_heartbeat;
-+ led-failsafe = &led_heartbeat;
-+ led-running = &led_heartbeat;
-+ led-upgrade = &led_heartbeat;
- };
-
- chosen {
-@@ -89,11 +94,10 @@
- led-controller {
- compatible = "pwm-leds";
-
-- led-1 {
-+ led_heartbeat: heartbeat {
- label = "marduk:red:heartbeat";
- pwms = <&pwm 3 300000>;
- max-brightness = <255>;
-- linux,default-trigger = "heartbeat";
- };
- };
-
More information about the lede-commits
mailing list