[openwrt/openwrt] ath79: add support for D-Link DIR-859 A3
LEDE Commits
lede-commits at lists.infradead.org
Mon May 22 06:28:11 PDT 2023
chunkeey pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/0ffbef9317a1dc049ad259c1ec1530355efc0552
commit 0ffbef9317a1dc049ad259c1ec1530355efc0552
Author: Shiji Yang <yangshiji66 at qq.com>
AuthorDate: Fri May 5 01:50:36 2023 +0000
ath79: add support for D-Link DIR-859 A3
Specifications:
SOC: QCA9563 775 MHz + QCA9880
Switch: QCA8337N-AL3C
RAM: Winbond W9751G6KB-25 64 MiB
Flash: Winbond W25Q128FVSG 16 MiB
WLAN: Wi-Fi4 2.4 GHz 3*3 + 5 GHz 3*3
LAN: LAN ports *4
WAN: WAN port *1
Buttons: reset *1 + wps *1
LEDs: ethernet *5, power, wlan, wps
MAC Address:
use address source1 source2
label 40:9b:xx:xx:xx:3c lan && wlan u-boot,env at ethaddr
lan 40:9b:xx:xx:xx:3c devdata at 0x3f $label
wan 40:9b:xx:xx:xx:3f devdata at 0x8f $label + 3
wlan2g 40:9b:xx:xx:xx:3c devdata at 0x5b $label
wlan5g 40:9b:xx:xx:xx:3e devdata at 0x76 $label + 2
Install via Web UI:
Apply factory image in the stock firmware's Web UI.
Install via Emergency Room Mode:
DIR-859 A1 will enter recovery mode when the system fails to boot
or press reset button for about 10 seconds.
First, set computer IP to 192.168.0.5 and Gateway to 192.168.0.1.
Then we can open http://192.168.0.1 in the web browser to upload
OpenWrt factory image or stock firmware. Some modern browsers may
need to turn on compatibility mode.
Signed-off-by: Shiji Yang <yangshiji66 at qq.com>
---
package/boot/uboot-envtools/files/ath79 | 1 +
.../linux/ath79/dts/qca9563_dlink_dir-859-a3.dts | 64 ++++++++++++++++++++++
.../linux/ath79/dts/qca9563_dlink_dir-8x9-a1.dtsi | 4 +-
.../ath79/generic/base-files/etc/board.d/01_leds | 3 +
.../generic/base-files/etc/board.d/02_network | 5 ++
.../base-files/etc/uci-defaults/09_fix-checksum | 1 +
target/linux/ath79/image/generic.mk | 14 ++++-
7 files changed, 88 insertions(+), 4 deletions(-)
diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79
index 38fc663e70..7c30aa052a 100644
--- a/package/boot/uboot-envtools/files/ath79
+++ b/package/boot/uboot-envtools/files/ath79
@@ -28,6 +28,7 @@ arduino,yun|\
buffalo,bhr-4grv2|\
devolo,magic-2-wifi|\
dlink,dir-859-a1|\
+dlink,dir-859-a3|\
dlink,dir-869-a1|\
engenius,eap1200h|\
engenius,eap1750h|\
diff --git a/target/linux/ath79/dts/qca9563_dlink_dir-859-a3.dts b/target/linux/ath79/dts/qca9563_dlink_dir-859-a3.dts
new file mode 100644
index 0000000000..164e0802f9
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_dlink_dir-859-a3.dts
@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca9563_dlink_dir-8x9-a1.dtsi"
+
+#include <dt-bindings/leds/common.h>
+
+/ {
+ compatible = "dlink,dir-859-a3", "qca,qca9563";
+ model = "D-Link DIR-859 A3";
+
+ aliases {
+ label-mac-device = &wmac;
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "green:power";
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_POWER;
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ };
+
+ wan {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_WAN;
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_WLAN;
+ gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wps {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_WPS;
+ gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&ath10k {
+ nvmem-cells = <&calibration_ath10k>, <&macaddr_bdcfg_ethaddr 2>;
+ nvmem-cell-names = "calibration", "mac-address";
+};
+
+&bdcfg {
+ macaddr_bdcfg_ethaddr: ethaddr {
+ #nvmem-cell-cells = <1>;
+ };
+};
+
+&wmac {
+ nvmem-cells = <&calibration_ath9k>, <&macaddr_bdcfg_ethaddr 0>;
+ nvmem-cell-names = "calibration", "mac-address";
+};
diff --git a/target/linux/ath79/dts/qca9563_dlink_dir-8x9-a1.dtsi b/target/linux/ath79/dts/qca9563_dlink_dir-8x9-a1.dtsi
index 754fcd415d..3fd9790c4a 100644
--- a/target/linux/ath79/dts/qca9563_dlink_dir-8x9-a1.dtsi
+++ b/target/linux/ath79/dts/qca9563_dlink_dir-8x9-a1.dtsi
@@ -28,7 +28,7 @@
&pcie {
status = "okay";
- wifi at 0,0 {
+ ath10k: wifi at 0,0 {
compatible = "qcom,ath10k";
reg = <0x0000 0 0 0 0>;
@@ -56,7 +56,7 @@
read-only;
};
- partition at 40000 {
+ bdcfg: partition at 40000 {
compatible = "u-boot,env";
label = "bdcfg";
reg = <0x040000 0x010000>;
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index d3508049ba..2ee4ed2544 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -234,6 +234,9 @@ dlink,dap-1365-a1)
dlink,dir-859-a1)
ucidef_set_led_switch "internet" "WAN" "green:internet" "switch0" "0x20"
;;
+dlink,dir-859-a3)
+ ucidef_set_led_switch "wan" "WAN" "green:wan" "switch0" "0x20"
+ ;;
engenius,ens202ext-v1|\
engenius,enstationac-v1)
ucidef_set_rssimon "wlan0" "200000" "1"
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index 487467cd59..4f535f8a64 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -291,6 +291,7 @@ ath79_setup_interfaces()
dlink,dir-842-c2|\
dlink,dir-842-c3|\
dlink,dir-859-a1|\
+ dlink,dir-859-a3|\
dlink,dir-869-a1|\
engenius,epg5000|\
engenius,esr1200|\
@@ -661,6 +662,10 @@ ath79_setup_macs()
lan_mac=$(mtd_get_mac_text "devdata" 0xc9)
wan_mac=$(mtd_get_mac_text "devdata" 0x79)
;;
+ dlink,dir-859-a3)
+ lan_mac=$(get_mac_label)
+ wan_mac=$(macaddr_add "$lan_mac" 3)
+ ;;
qihoo,c301|\
wd,mynet-n600|\
wd,mynet-n750)
diff --git a/target/linux/ath79/generic/base-files/etc/uci-defaults/09_fix-checksum b/target/linux/ath79/generic/base-files/etc/uci-defaults/09_fix-checksum
index ad3db95a0c..0ea81a8dc3 100644
--- a/target/linux/ath79/generic/base-files/etc/uci-defaults/09_fix-checksum
+++ b/target/linux/ath79/generic/base-files/etc/uci-defaults/09_fix-checksum
@@ -23,6 +23,7 @@ dlink,dap-3662-a1)
;;
dlink,dir-629-a1|\
dlink,dir-859-a1|\
+dlink,dir-859-a3|\
dlink,dir-869-a1|\
qihoo,c301)
fix_seama_header
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index f8969a919c..788520120d 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -1143,18 +1143,28 @@ define Device/dlink_dir-842-c3
endef
TARGET_DEVICES += dlink_dir-842-c3
-define Device/dlink_dir-859-a1
+define Device/dlink_dir-859-ax
$(Device/seama)
SOC := qca9563
DEVICE_VENDOR := D-Link
DEVICE_MODEL := DIR-859
- DEVICE_VARIANT := A1
IMAGE_SIZE := 15872k
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
SEAMA_SIGNATURE := wrgac37_dlink.2013gui_dir859
endef
+
+define Device/dlink_dir-859-a1
+ $(Device/dlink_dir-859-ax)
+ DEVICE_VARIANT := A1
+endef
TARGET_DEVICES += dlink_dir-859-a1
+define Device/dlink_dir-859-a3
+ $(Device/dlink_dir-859-ax)
+ DEVICE_VARIANT := A3
+endef
+TARGET_DEVICES += dlink_dir-859-a3
+
define Device/dlink_dir-869-a1
$(Device/seama)
SOC := qca9563
More information about the lede-commits
mailing list