[openwrt/openwrt] ipq40xx: add support for Wallystech DR40x9
LEDE Commits
lede-commits at lists.infradead.org
Tue Mar 21 08:39:48 PDT 2023
xback pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/eb564690c995b284204aa762c0f77f3064419a9c
commit eb564690c995b284204aa762c0f77f3064419a9c
Author: Robert Marko <robert.marko at sartura.hr>
AuthorDate: Tue Jun 30 18:07:50 2020 +0200
ipq40xx: add support for Wallystech DR40x9
Adds support for the Wallys DR40x9 series boards.
They come in IPQ4019 and IPQ4029 versions.
IPQ4019/4029 only differ in that that IPQ4029 is the industrial version that is rated to higher temperatures.
Specifications are:
* CPU: Qualcomm IPQ40x9 (4x ARMv7A Cortex A7) at 716 MHz
* RAM: 512 MB
* Storage: 2MB of SPI-NOR, 128 MB of parallel NAND
* USB 3.0 TypeA port for users
* MiniPCI-E with PCI-E 2.0 link
* MiniPCI-E for LTE modems with only USB2.0 link
* 2 SIM card slots that are selected via GPIO11
* MicroSD card slot
* Ethernet: 2x GBe with 24~48V passive POE
* SFP port (Does not work, I2C and GPIO's not connected on hardware)
* DC Jack
* UART header
* WLAN: In-SoC 2x2 802.11b/g/n and 2x2 802.11a/n/ac
* 4x MMCX connectors for WLAN
* Reset button
* 8x LED-s
Installation instructions:
Connect to UART, pins are like this:
-> 3.3V | TX | RX | GND
Settings are 115200 8n1
Boot initramfs from TFTP:
tftpboot 0x84000000 openwrt-ipq40xx-generic-wallys_dr40x9-initramfs-fit-uImage.itb
bootm
Then copy the sysupgrade image to the /tmp folder and execute sysupgrade -n <image_name>
The board file binary was provided from Wallystech on March 14th 2023
including full permission to use and distribute.
Signed-off-by: Robert Marko <robert.marko at sartura.hr>
Signed-off-by: Koen Vandeputte <koen.vandeputte at citymesh.com>
---
package/firmware/ipq-wifi/Makefile | 2 +
.../ipq40xx/base-files/etc/board.d/02_network | 1 +
.../base-files/etc/board.d/03_gpio_switches | 3 +
.../ipq40xx/base-files/lib/upgrade/platform.sh | 3 +-
.../arch/arm/boot/dts/qcom-ipq40x9-dr40x9.dts | 422 +++++++++++++++++++++
target/linux/ipq40xx/image/generic.mk | 13 +
6 files changed, 443 insertions(+), 1 deletion(-)
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile
index 846032c96f..f3bf1185f8 100644
--- a/package/firmware/ipq-wifi/Makefile
+++ b/package/firmware/ipq-wifi/Makefile
@@ -54,6 +54,7 @@ ALLWIFIBOARDS:= \
redmi_ax6 \
sony_ncp-hg100-cellular \
teltonika_rutx \
+ wallys_dr40x9 \
xiaomi_ax3600 \
xiaomi_ax9000 \
zte_mf18a \
@@ -158,6 +159,7 @@ $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac-c2,Qxwlan E2600AC C2))
$(eval $(call generate-ipq-wifi-package,redmi_ax6,Redmi AX6))
$(eval $(call generate-ipq-wifi-package,sony_ncp-hg100-cellular,Sony NCP-HG100/Cellular))
$(eval $(call generate-ipq-wifi-package,teltonika_rutx,Teltonika RUTX))
+$(eval $(call generate-ipq-wifi-package,wallys_dr40x9,Wallys DR40X9))
$(eval $(call generate-ipq-wifi-package,xiaomi_ax3600,Xiaomi AX3600))
$(eval $(call generate-ipq-wifi-package,xiaomi_ax9000,Xiaomi AX9000))
$(eval $(call generate-ipq-wifi-package,zte_mf18a,ZTE MF18A))
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 3625938e38..37b9ca268b 100644
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -39,6 +39,7 @@ ipq40xx_setup_interfaces()
mikrotik,cap-ac|\
netgear,wac510|\
sony,ncp-hg100-cellular|\
+ wallys,dr40x9|\
zte,mf18a|\
zte,mf289f)
ucidef_set_interfaces_lan_wan "lan" "wan"
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches b/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches
index 4918e2ccc1..f76fe9402d 100644
--- a/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches
+++ b/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches
@@ -32,6 +32,9 @@ mikrotik,hap-ac3-lte6-kit)
sony,ncp-hg100-cellular)
ucidef_add_gpio_switch "uart_dbgcon_en" "debug console enable" "427" "1"
;;
+wallys,dr40x9)
+ ucidef_add_gpio_switch "sim_card_select" "SIM card select" "423" "0"
+ ;;
zte,mf286d|\
zte,mf289f)
ucidef_add_gpio_switch "power_btn_block" "Power button blocker" "421" "0"
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index 2012213a56..988921fa8c 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -119,7 +119,8 @@ platform_do_upgrade() {
netgear,wac510 |\
p2w,r619ac-64m |\
p2w,r619ac-128m |\
- qxwlan,e2600ac-c2)
+ qxwlan,e2600ac-c2 |\
+ wallys,dr40x9)
nand_do_upgrade "$1"
;;
glinet,gl-b2200)
diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq40x9-dr40x9.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq40x9-dr40x9.dts
new file mode 100644
index 0000000000..b90b6b28c3
--- /dev/null
+++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq40x9-dr40x9.dts
@@ -0,0 +1,422 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "Wallystech DR40X9";
+ compatible = "wallys,dr40x9";
+
+ chosen {
+ bootargs-append = " ubi.mtd=ubi root=/dev/ubiblock0_1";
+ };
+
+ soc {
+ counter at 4a1000 {
+ compatible = "qcom,qca-gcnt";
+ reg = <0x4a1000 0x4>;
+ };
+
+ tcsr at 1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr at 194b000 {
+ status = "okay";
+
+ /* select hostmode */
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ };
+
+ ess_tcsr at 1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr at 1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ wlan2g {
+ label = "dr4029:green:wlan2g";
+ gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wlan5g {
+ label = "dr4029:green:wlan5g";
+ gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ wlan2g-strength {
+ label = "dr4029:green:wlan2g-strength";
+ gpios = <&tlmm 36 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan5g-strength {
+ label = "dr4029:green:wlan5g-strength";
+ gpios = <&tlmm 39 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&tlmm {
+ mdio_pins: mdio_pinmux {
+ mux_1 {
+ pins = "gpio6";
+ function = "mdio";
+ bias-pull-up;
+ };
+ mux_2 {
+ pins = "gpio7";
+ function = "mdc";
+ bias-pull-up;
+ };
+ };
+
+ serial0_pins: serial0_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ serial1_pins: serial1_pinmux {
+ mux {
+ pins = "gpio8", "gpio9";
+ function = "blsp_uart1";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pinmux {
+ function = "blsp_spi0";
+ pins = "gpio13", "gpio14", "gpio15";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pinmux_cs {
+ function = "gpio";
+ pins = "gpio12";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ nand_pins: nand_pins {
+ pullups {
+ pins = "gpio52", "gpio53", "gpio58", "gpio59";
+ function = "qpic";
+ bias-pull-up;
+ };
+
+ pulldowns {
+ pins = "gpio54", "gpio55", "gpio56", "gpio57",
+ "gpio60", "gpio62", "gpio63", "gpio64",
+ "gpio65", "gpio66", "gpio67", "gpio68",
+ "gpio69";
+ function = "qpic";
+ bias-pull-down;
+ };
+ };
+
+ sd_pins: sd_pins {
+ pinmux {
+ function = "sdio";
+ pins = "gpio23", "gpio24", "gpio25", "gpio26",
+ "gpio28", "gpio29", "gpio30", "gpio31";
+ drive-strength = <10>;
+ };
+ pinmux_sd_clk {
+ function = "sdio";
+ pins = "gpio27";
+ drive-strength = <16>;
+ };
+ pinmux_sd7 {
+ function = "sdio";
+ pins = "gpio32";
+ drive-strength = <10>;
+ bias-disable;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ status = "okay";
+
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <24000000>;
+ reg = <0>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition0 at 0 {
+ label = "0:SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+
+ partition1 at 40000 {
+ label = "0:MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+
+ partition2 at 60000 {
+ label = "0:QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+
+ partition3 at c0000 {
+ label = "0:CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+
+ partition4 at d0000 {
+ label = "0:DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+
+ partition5 at e0000 {
+ label = "0:APPSBLENV"; /* uboot env */
+ reg = <0x000e0000 0x00010000>;
+ read-only;
+ };
+
+ partition6 at f0000 {
+ label = "0:APPSBL"; /* uboot */
+ reg = <0x000f0000 0x00080000>;
+ read-only;
+ };
+
+ partition7 at 170000 {
+ label = "0:ART";
+ reg = <0x00170000 0x00010000>;
+ read-only;
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ precal_art_1000: precal at 1000 {
+ reg = <0x1000 0x2f20>;
+ };
+
+ precal_art_5000: precal at 5000 {
+ reg = <0x5000 0x2f20>;
+ };
+
+ macaddr_art_0: mac-address at 0 {
+ reg = <0x0 0x6>;
+ };
+
+ macaddr_art_6: mac-address at 6 {
+ reg = <0x6 0x6>;
+ };
+
+ macaddr_art_1006: mac-address at 1006 {
+ reg = <0x1006 0x6>;
+ };
+
+ macaddr_art_5006: mac-address at 5006 {
+ reg = <0x5006 0x6>;
+ };
+
+ };
+
+ partition8 at 180000 {
+ label = "0:CONFIG";
+ reg = <0x00180000 0x00010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&nand {
+ status = "okay";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ nand at 0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "ubi";
+ reg = <0x00000000 0x04000000>;
+ };
+ };
+ };
+};
+
+&blsp1_uart1 {
+ status = "okay";
+ pinctrl-0 = <&serial0_pins>;
+ pinctrl-names = "default";
+};
+
+&blsp1_uart2 {
+ status = "okay";
+ pinctrl-0 = <&serial1_pins>;
+ pinctrl-names = "default";
+};
+
+&crypto {
+ status = "okay";
+};
+
+&cryptobam {
+ num-channels = <4>;
+ qcom,num-ees = <2>;
+ status = "okay";
+};
+
+&mdio {
+ status = "okay";
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ reset-gpios = <&tlmm 41 GPIO_ACTIVE_LOW>;
+ reset-delay-us = <2000>;
+};
+
+&pcie0 {
+ status = "okay";
+
+ perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 40 GPIO_ACTIVE_LOW>;
+
+ /* Unpolulated slot */
+ bridge at 0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+ };
+};
+
+&vqmmc {
+ status = "okay";
+};
+
+&sdhci {
+ status = "okay";
+ pinctrl-0 = <&sd_pins>;
+ pinctrl-names = "default";
+ cd-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>;
+ vqmmc-supply = <&vqmmc>;
+};
+
+&gmac {
+ status = "okay";
+};
+
+&switch {
+ status = "okay";
+};
+
+&swport4 {
+ status = "okay";
+ label = "wan";
+ nvmem-cells = <&macaddr_art_0>;
+ nvmem-cell-names = "mac-address";
+};
+
+&swport5 {
+ status = "okay";
+ label = "lan";
+ nvmem-cells = <&macaddr_art_6>;
+ nvmem-cell-names = "mac-address";
+};
+
+&wifi0 {
+ status = "okay";
+ nvmem-cells = <&precal_art_1000>, <&macaddr_art_1006>;
+ nvmem-cell-names = "pre-calibration", "mac-address";
+ qcom,ath10k-calibration-variant = "Wallys-DR40X9";
+};
+
+&wifi1 {
+ status = "okay";
+ nvmem-cell-names = "pre-calibration", "mac-address";
+ nvmem-cells = <&precal_art_5000>, <&macaddr_art_5006>;
+ qcom,ath10k-calibration-variant = "Wallys-DR40X9";
+};
+
+&usb2 {
+ status = "okay";
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
+
+&usb3 {
+ status = "okay";
+};
+
+&usb3_ss_phy {
+ status = "okay";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&prng {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
diff --git a/target/linux/ipq40xx/image/generic.mk b/target/linux/ipq40xx/image/generic.mk
index 68a45dbf9b..48514b8841 100644
--- a/target/linux/ipq40xx/image/generic.mk
+++ b/target/linux/ipq40xx/image/generic.mk
@@ -1122,6 +1122,19 @@ endef
# Missing DSA Setup
#TARGET_DEVICES += unielec_u4019-32m
+define Device/wallys_dr40x9
+ $(call Device/FitImage)
+ $(call Device/UbiFit)
+ DEVICE_VENDOR := Wallys
+ DEVICE_MODEL := DR40X9
+ SOC := qcom-ipq40x9
+ DEVICE_DTS_CONFIG := config at ap.dk07.1-c1
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ DEVICE_PACKAGES := ipq-wifi-wallys_dr40x9
+endef
+TARGET_DEVICES += wallys_dr40x9
+
define Device/zte_mf18a
$(call Device/FitImage)
DEVICE_VENDOR := ZTE
More information about the lede-commits
mailing list