[openwrt/openwrt] bmips: add support for Sercomm AD1018
LEDE Commits
lede-commits at lists.infradead.org
Thu Jun 15 11:58:56 PDT 2023
noltari pushed a commit to openwrt/openwrt.git, branch openwrt-23.05:
https://git.openwrt.org/3d66e7f1db70c98876ea6e9aeb57622d6d30c5e8
commit 3d66e7f1db70c98876ea6e9aeb57622d6d30c5e8
Author: Álvaro Fernández Rojas <noltari at gmail.com>
AuthorDate: Mon Jun 12 19:51:22 2023 +0200
bmips: add support for Sercomm AD1018
The Sercomm AD1018 is a wifi fast ethernet router, 2.4 GHz single band with
two internal antennas.
Hardware:
- SoC: Broadcom BCM6328
- CPU: single core BMIPS4350 @ 320Mhz
- RAM: 64 MB (v1) / 128 MB (v2) DDR
- Flash: 128 MB NAND
- Ethernet LAN: 4x 100Mbit
- Wifi 2.4 GHz: miniPCI Broadcom BCM43217 802.11bgn
- USB: 1x 2.0
- Buttons: 3x (reset)
- LEDs: yes
- UART: yes
Installation via OEM web UI:
1. Use the admin credentials to login via web UI
2. Go to Managament->Update firmware and select the OpenWrt CFE firmware
3. Press "Update Firmware" button and wait some minutes until it finish
Signed-off-by: Álvaro Fernández Rojas <noltari at gmail.com>
(cherry picked from commit 38ebb2eafde604ff6d9b0021d1d21208070a2d09)
---
.../base-files/etc/board.d/{02_network => 01_leds} | 7 +-
.../bcm6328/base-files/etc/board.d/02_network | 4 +
.../bcm6328/base-files/lib/upgrade/platform.sh | 3 +
target/linux/bmips/dts/bcm6328-sercomm-ad1018.dts | 312 +++++++++++++++++++++
target/linux/bmips/image/bcm6328.mk | 18 ++
5 files changed, 340 insertions(+), 4 deletions(-)
diff --git a/target/linux/bmips/bcm6328/base-files/etc/board.d/02_network b/target/linux/bmips/bcm6328/base-files/etc/board.d/01_leds
similarity index 56%
copy from target/linux/bmips/bcm6328/base-files/etc/board.d/02_network
copy to target/linux/bmips/bcm6328/base-files/etc/board.d/01_leds
index c9c704067e..5ece1f7ba1 100644
--- a/target/linux/bmips/bcm6328/base-files/etc/board.d/02_network
+++ b/target/linux/bmips/bcm6328/base-files/etc/board.d/01_leds
@@ -1,14 +1,13 @@
# SPDX-License-Identifier: GPL-2.0-or-later
+. /lib/functions/leds.sh
. /lib/functions/uci-defaults.sh
board_config_update
case "$(board_name)" in
-comtrend,ar-5381u |\
-comtrend,ar-5387un)
- ucidef_set_bridge_device switch
- ucidef_set_interface_lan "lan1 lan2 lan3 lan4"
+sercomm,ad1018)
+ ucidef_set_led_usbport "usb" "USB" "green:usb" "usb1-port1" "usb2-port1"
;;
esac
diff --git a/target/linux/bmips/bcm6328/base-files/etc/board.d/02_network b/target/linux/bmips/bcm6328/base-files/etc/board.d/02_network
index c9c704067e..66f9282e48 100644
--- a/target/linux/bmips/bcm6328/base-files/etc/board.d/02_network
+++ b/target/linux/bmips/bcm6328/base-files/etc/board.d/02_network
@@ -10,6 +10,10 @@ comtrend,ar-5387un)
ucidef_set_bridge_device switch
ucidef_set_interface_lan "lan1 lan2 lan3 lan4"
;;
+sercomm,ad1018)
+ ucidef_set_bridge_device switch
+ ucidef_set_interface_lan "lan1 lan2 lan3 fibre"
+ ;;
esac
board_config_flush
diff --git a/target/linux/bmips/bcm6328/base-files/lib/upgrade/platform.sh b/target/linux/bmips/bcm6328/base-files/lib/upgrade/platform.sh
index 1cf95be26a..d820b20718 100644
--- a/target/linux/bmips/bcm6328/base-files/lib/upgrade/platform.sh
+++ b/target/linux/bmips/bcm6328/base-files/lib/upgrade/platform.sh
@@ -9,6 +9,9 @@ platform_check_image() {
platform_do_upgrade() {
case "$(board_name)" in
+ sercomm,ad1018)
+ nand_do_upgrade "$1"
+ ;;
*)
default_do_upgrade "$1"
;;
diff --git a/target/linux/bmips/dts/bcm6328-sercomm-ad1018.dts b/target/linux/bmips/dts/bcm6328-sercomm-ad1018.dts
new file mode 100644
index 0000000000..5d18266818
--- /dev/null
+++ b/target/linux/bmips/dts/bcm6328-sercomm-ad1018.dts
@@ -0,0 +1,312 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "bcm6328.dtsi"
+
+/ {
+ model = "Sercomm AD1018";
+ compatible = "sercomm,ad1018", "brcm,bcm6328";
+
+ aliases {
+ led-boot = &led_power_green;
+ led-failsafe = &led_power_green;
+ led-running = &led_power_green;
+ led-upgrade = &led_power_green;
+ };
+
+ keys {
+ compatible = "gpio-keys-polled";
+ poll-interval = <100>;
+
+ wps {
+ label = "wps";
+ gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ debounce-interval = <60>;
+ };
+
+ wlan {
+ label = "wlan";
+ gpios = <&gpio 25 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WLAN>;
+ debounce-interval = <60>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 31 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ debounce-interval = <60>;
+ };
+ };
+
+ bcm432217-sprom {
+ compatible = "brcm,bcma-sprom";
+
+ pci-bus = <1>;
+ pci-dev = <0>;
+
+ nvmem-cells = <&macaddr_cferom_6a0>;
+ nvmem-cell-names = "mac-address";
+ mac-address-increment = <1>;
+
+ brcm,sprom = "brcm/bcm43217-sprom.bin";
+ brcm,sprom-fixups = <6 0x1c00>,
+ <65 0x1256>,
+ <96 0x2046>,
+ <97 0xfe69>,
+ <98 0x1726>,
+ <99 0xfa5c>,
+ <112 0x2046>,
+ <113 0xfea8>,
+ <114 0x1978>,
+ <115 0xfa26>,
+ <161 0x2222>,
+ <169 0x2222>,
+ <171 0x2222>,
+ <173 0x2222>,
+ <174 0x4444>,
+ <175 0x2222>,
+ <176 0x4444>;
+ };
+};
+
+&ehci {
+ status = "okay";
+};
+
+ðernet {
+ status = "okay";
+
+ nvmem-cells = <&macaddr_cferom_6a0>;
+ nvmem-cell-names = "mac-address";
+};
+
+&leds {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds &pinctrl_serial_led
+ &pinctrl_ephy0_spd_led &pinctrl_ephy1_act_led
+ &pinctrl_ephy2_act_led &pinctrl_ephy3_act_led>;
+
+ brcm,serial-leds;
+ brcm,serial-shift-inv;
+ brcm,serial-dat-low;
+
+ led at 0 {
+ reg = <0>;
+ active-low;
+ label = "red:internet";
+ };
+
+ led at 1 {
+ reg = <1>;
+ active-low;
+ label = "green:internet";
+ };
+
+ led_power_green: led at 8 {
+ reg = <8>;
+ active-low;
+ label = "green:power";
+ default-state = "on";
+ };
+
+ led at 10 {
+ reg = <10>;
+ active-low;
+ label = "green:adsl";
+ };
+
+ led at 11 {
+ reg = <11>;
+ active-low;
+ label = "red:adsl";
+ };
+
+ led at 12 {
+ reg = <12>;
+ active-low;
+ label = "green:phone";
+ };
+
+ led at 13 {
+ reg = <13>;
+ active-low;
+ label = "green:wps";
+ };
+
+ led at 14 {
+ reg = <14>;
+ active-low;
+ label = "green:wifi";
+ };
+
+ led at 15 {
+ reg = <15>;
+ active-low;
+ label = "green:usb";
+ };
+
+ led at 17 {
+ /* EPHY0 Spd */
+ reg = <17>;
+ brcm,hardware-controlled;
+ };
+};
+
+&ohci {
+ status = "okay";
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pinctrl {
+ pinctrl_leds: leds {
+ function = "led";
+ pins = "gpio0", "gpio1";
+ };
+};
+
+&nflash {
+ status = "okay";
+
+ nandcs at 0 {
+ compatible = "brcm,nandcs";
+ reg = <0>;
+ nand-ecc-step-size = <512>;
+ nand-ecc-strength = <15>;
+ nand-on-flash-bbt;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cferom: partition at 0 {
+ label = "cferom";
+ reg = <0x0000000 0x0020000>;
+ read-only;
+ };
+
+ partition at 20000 {
+ label = "mmap";
+ reg = <0x0020000 0x00a0000>;
+ read-only;
+ };
+
+ partition at c0000 {
+ label = "cferam1";
+ reg = <0x00c0000 0x0140000>;
+ read-only;
+ };
+
+ partition at 200000 {
+ label = "cferam2";
+ reg = <0x0200000 0x0140000>;
+ read-only;
+ };
+
+ partition at 340000 {
+ label = "serial";
+ reg = <0x0340000 0x00a0000>;
+ read-only;
+ };
+
+ partition at 3e0000 {
+ label = "protect";
+ reg = <0x03e0000 0x0140000>;
+ read-only;
+ };
+
+ partition at 6920000 {
+ label = "bootflag1";
+ reg = <0x6920000 0x0140000>;
+ read-only;
+ };
+
+ partition at 6a60000 {
+ label = "bootflag2";
+ reg = <0x6a60000 0x0140000>;
+ read-only;
+ };
+
+ partition at 520000 {
+ compatible = "sercomm,wfi";
+ label = "wfi";
+ reg = <0x0520000 0x6400000>;
+ };
+
+ partition at 6ba0000 {
+ label = "xml_cfg";
+ reg = <0x6ba0000 0x0280000>;
+ read-only;
+ };
+
+ partition at 6e20000 {
+ label = "app_dat";
+ reg = <0x6e20000 0x0280000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&switch0 {
+ ports {
+ port at 0 {
+ reg = <0>;
+ label = "fibre";
+
+ phy-handle = <&phy1>;
+ phy-mode = "mii";
+ };
+
+ port at 1 {
+ reg = <1>;
+ label = "lan3";
+
+ phy-handle = <&phy2>;
+ phy-mode = "mii";
+ };
+
+ port at 2 {
+ reg = <2>;
+ label = "lan2";
+
+ phy-handle = <&phy3>;
+ phy-mode = "mii";
+ };
+
+ port at 3 {
+ reg = <3>;
+ label = "lan1";
+
+ phy-handle = <&phy4>;
+ phy-mode = "mii";
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&usbh {
+ status = "okay";
+};
+
+&cferom {
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_cferom_6a0: macaddr at 6a0 {
+ reg = <0x6a0 0x6>;
+ };
+};
diff --git a/target/linux/bmips/image/bcm6328.mk b/target/linux/bmips/image/bcm6328.mk
index dfa134df94..ef74410f1e 100644
--- a/target/linux/bmips/image/bcm6328.mk
+++ b/target/linux/bmips/image/bcm6328.mk
@@ -25,3 +25,21 @@ define Device/comtrend_ar-5387un
kmod-leds-bcm6328
endef
TARGET_DEVICES += comtrend_ar-5387un
+
+define Device/sercomm_ad1018
+ $(Device/sercomm-nand)
+ DEVICE_VENDOR := Sercomm
+ DEVICE_MODEL := AD1018
+ CHIP_ID := 6328
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ SUBPAGESIZE := 512
+ VID_HDR_OFFSET := 2048
+ DEVICE_PACKAGES += $(USB2_PACKAGES) \
+ $(B43_PACKAGES) broadcom-43217-sprom \
+ kmod-leds-bcm6328
+ SERCOMM_FSVER := 1001
+ SERCOMM_HWVER := 1415153
+ SERCOMM_SWVER := 3013
+endef
+TARGET_DEVICES += sercomm_ad1018
More information about the lede-commits
mailing list