[openwrt/openwrt] bmips: add support for Netgear EVG2000
LEDE Commits
lede-commits at lists.infradead.org
Sun Jun 11 00:58:27 PDT 2023
noltari pushed a commit to openwrt/openwrt.git, branch openwrt-23.05:
https://git.openwrt.org/13579e64417545dca6bc878927d9f48f3dfe4af9
commit 13579e64417545dca6bc878927d9f48f3dfe4af9
Author: Daniel González Cabanelas <dgcbueu at gmail.com>
AuthorDate: Sat Jun 10 21:05:33 2023 +0200
bmips: add support for Netgear EVG2000
The Netgear EVG2000 is a wifi gigabit router, 2.4 GHz single band with
two internal antennas integrated in the main PCB.
Hardware:
- SoC: Broadcom BCM6369
- CPU: dual core BMIPS4350 V3.1 @400Mhz
- RAM: 64 MB DDR
- Flash: 16 MB parallel NOR
- LAN switch: Broadcom BCM53115, 5x 1Gbit
- Wifi 2.4 GHz: Broadcom BCM4322 802.11bgn
- USB: 2x 2.0
- Buttons: 2x, 1 reset
- LEDs: 10x
- FXS: 2x
- UART: yes
Installation via CFE web UI:
1. Power off the router and make a temporal TX-RX shortcircuit on the
serial pins.
2. Power on the router and wait 3 or more seconds
3. Remove the TX-RX shortcircuit
4. Browse to http://192.168.1.1 or http://192.168.0.1 and upload the
firmware
5. Wait a few minutes for it to finish
Signed-off-by: Daniel González Cabanelas <dgcbueu at gmail.com>
---
.../bmips/bcm6368/base-files/etc/board.d/01_leds | 5 +
.../bcm6368/base-files/etc/board.d/02_network | 3 +-
.../bcm6368/base-files/etc/uci-defaults/09_fix_crc | 1 +
target/linux/bmips/dts/bcm6369-netgear-evg2000.dts | 237 +++++++++++++++++++++
target/linux/bmips/image/bcm6368.mk | 15 ++
5 files changed, 260 insertions(+), 1 deletion(-)
diff --git a/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds b/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds
index e68a4e947b..fb7cca17e5 100644
--- a/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds
+++ b/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds
@@ -15,6 +15,11 @@ netgear,dgnd3800b)
ucidef_set_led_usbport "usb1" "USB1" "green:usb1" "usb1-port1" "usb2-port1"
ucidef_set_led_usbport "usb2" "USB2" "green:usb2" "usb1-port2" "usb2-port2"
;;
+netgear,evg2000)
+ ucidef_set_led_netdev "lan" "LAN" "green:lan" "switch.1"
+ ucidef_set_led_netdev "wan" "WAN" "green:wan" "wan"
+ ucidef_set_led_usbdev "usb" "USB" "green:usb" "usb1-port1" "usb2-port1" "usb1-port2" "usb2-port2"
+ ;;
observa,vh4032n)
ucidef_set_led_usbport "usb1" "USB1" "blue:hspa" "usb1-port1" "usb2-port1"
ucidef_set_led_usbport "usb2" "USB2" "red:hspa" "1-2-port1" "1-2-port2"
diff --git a/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network b/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network
index f99005acd7..76145024c1 100644
--- a/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network
+++ b/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network
@@ -11,7 +11,8 @@ observa,vh4032n)
ucidef_set_interface_lan "lan1 lan2 lan3 lan4"
;;
netgear,dgnd3700-v1 |\
-netgear,dgnd3800b)
+netgear,dgnd3800b |\
+netgear,evg2000)
ucidef_set_bridge_device switch
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
;;
diff --git a/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc b/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc
index d4ff723d14..363e492594 100644
--- a/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc
+++ b/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc
@@ -4,6 +4,7 @@
case "$(board_name)" in
comtrend,vr-3025u |\
+netgear,evg2000 |\
observa,vh4032n)
mtd fixtrx firmware
;;
diff --git a/target/linux/bmips/dts/bcm6369-netgear-evg2000.dts b/target/linux/bmips/dts/bcm6369-netgear-evg2000.dts
new file mode 100644
index 0000000000..9f03c9e4dc
--- /dev/null
+++ b/target/linux/bmips/dts/bcm6369-netgear-evg2000.dts
@@ -0,0 +1,237 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "bcm6368.dtsi"
+
+/ {
+ model = "Netgear EVG2000";
+ compatible = "netgear,evg2000", "brcm,bcm6369", "brcm,bcm6368";
+
+ aliases {
+ led-boot = &led_power_green;
+ led-failsafe = &led_power_red;
+ led-running = &led_power_green;
+ led-upgrade = &led_power_green;
+ };
+
+ keys {
+ compatible = "gpio-keys-polled";
+ poll-interval = <100>;
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 25 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ debounce-interval = <60>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&gpio 26 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ debounce-interval = <60>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led at 2 {
+ label = "green:voip2";
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ };
+
+ led at 4 {
+ label = "red:internet";
+ gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+ };
+
+ led at 5 {
+ label = "green:internet";
+ gpios = <&gpio 5 GPIO_ACTIVE_LOW>;
+ };
+
+ led at 14 {
+ label = "green:voip1";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ };
+
+ led at 15 {
+ label = "green:usb";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ };
+
+ led_power_green: led at 22 {
+ label = "green:power";
+ gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ led_power_red: led at 23 {
+ label = "red:power";
+ gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
+ };
+
+ led at 24 {
+ label = "green:lan";
+ gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
+ };
+
+ led at 27 {
+ label = "green:wan";
+ gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ bcm4322-sprom {
+ compatible = "brcm,ssb-sprom";
+
+ pci-bus = <0>;
+ pci-dev = <1>;
+
+ nvmem-cells = <&macaddr_cfe_6a0>;
+ nvmem-cell-names = "mac-address";
+ mac-address-increment = <1>;
+
+ brcm,sprom = "brcm/bcm4322-sprom.bin";
+ brcm,sprom-fixups = <219 0xec08>;
+ };
+};
+
+&ehci {
+ status = "okay";
+};
+
+ðernet {
+ status = "okay";
+
+ nvmem-cells = <&macaddr_cfe_6a0>;
+ nvmem-cell-names = "mac-address";
+};
+
+&mdio_ext {
+ switch at 1e {
+ compatible = "brcm,bcm53115";
+ reg = <30>;
+
+ dsa,member = <1 0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ label = "wan";
+ };
+
+ port at 1 {
+ reg = <1>;
+ label = "lan1";
+ };
+
+ port at 2 {
+ reg = <2>;
+ label = "lan2";
+ };
+
+ port at 3 {
+ reg = <3>;
+ label = "lan3";
+ };
+
+ port at 4 {
+ reg = <4>;
+ label = "lan4";
+ };
+
+ port at 8 {
+ reg = <8>;
+
+ phy-mode = "rgmii";
+ ethernet = <&switch0port5>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+};
+
+&switch0 {
+ dsa,member = <0 0>;
+
+ ports {
+ switch0port5: port at 5 {
+ reg = <5>;
+ label = "extsw";
+
+ phy-mode = "rgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+};
+
+&pflash {
+ status = "okay";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cfe: partition at 0 {
+ label = "CFE";
+ reg = <0x000000 0x020000>;
+ read-only;
+ };
+
+ partition at 20000 {
+ label = "firmware";
+ reg = <0x020000 0xf40000>;
+ compatible = "brcm,bcm963xx-imagetag";
+ };
+
+ partition at f60000 {
+ label = "board_data";
+ reg = <0xf60000 0x080000>;
+ read-only;
+ };
+
+ partition at fe0000 {
+ label = "nvram";
+ reg = <0xfe0000 0x020000>;
+ };
+ };
+};
+
+&ohci {
+ status = "okay";
+};
+
+&pci {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&usbh {
+ status = "okay";
+};
+
+&cfe {
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_cfe_6a0: macaddr at 6a0 {
+ reg = <0x6a0 0x6>;
+ };
+};
diff --git a/target/linux/bmips/image/bcm6368.mk b/target/linux/bmips/image/bcm6368.mk
index 41bce9e938..82d7608fba 100644
--- a/target/linux/bmips/image/bcm6368.mk
+++ b/target/linux/bmips/image/bcm6368.mk
@@ -43,6 +43,21 @@ define Device/netgear_dgnd3800b
endef
TARGET_DEVICES += netgear_dgnd3800b
+define Device/netgear_evg2000
+ $(Device/bcm63xx_netgear)
+ DEVICE_MODEL := EVG2000
+ CFE_BOARD_ID := 96369PVG
+ CHIP_ID := 6368
+ SOC := bcm6369
+ BLOCKSIZE := 0x20000
+ NETGEAR_BOARD_ID := U12H154T90_NETGEAR
+ NETGEAR_REGION := 1
+ DEVICE_PACKAGES += $(USB2_PACKAGES) \
+ $(B43_PACKAGES) broadcom-4322-sprom \
+ kmod-leds-gpio
+endef
+TARGET_DEVICES += netgear_evg2000
+
define Device/observa_vh4032n
$(Device/bcm63xx-cfe)
DEVICE_VENDOR := Observa
More information about the lede-commits
mailing list