[openwrt/openwrt] ipq40xx: add support for Teltonika RUTX50
LEDE Commits
lede-commits at lists.infradead.org
Wed Jul 26 06:40:22 PDT 2023
blocktrron pushed a commit to openwrt/openwrt.git, branch openwrt-23.05:
https://git.openwrt.org/897d55bcdf864f4d40cf50396b963ca240bbc1fc
commit 897d55bcdf864f4d40cf50396b963ca240bbc1fc
Author: David Bauer <mail at david-bauer.net>
AuthorDate: Sat May 6 16:57:18 2023 +0200
ipq40xx: add support for Teltonika RUTX50
Hardware
--------
CPU: Qualcomm IPQ4018
RAM: 256M
Flash: 16MB SPI-NOR (W25Q128)
128MB SPI-NAND (XTX)
WiFi: 2T2R (2GHz 802.11n ; 5 GHz 802.11ac)
ETH: 4x LAN ; 1x WAN (Gigabit)
CELL: Quectel RG501Q 3G/4G/5G
UART: Available on the goldfinger connector (Pinout silkscreened)
115200 8N1 3V3 - Only connect RX / TX / GND
Installation
------------
1. Enable SSH in the Teltonika UI
(System --> Administration --> Access Control)
2. Check from which partition set the device is currently running from.
$ cat /proc/boot_info/rootfs/primaryboot
In case this output reads 0, install a Software update from Teltonika
first. After upgrade completion, check this file now reads 1 before
continuing.
2. Transfer the OpenWrt factory image to the device using scp. Use the
same password (user root!) as used for the Web-UI.
$ scp -O openwrt-factory.bin root at 192.168.1.1:/tmp
3. Connect to the device using ssh as the root user.
4. Install OpenWrt by writing the factory image to flash.
$ ubiformat /dev/mtd16 -y -f /tmp/openwrt-factory.bin
5. Instruct the bootloaer to boot from the first partition set.
$ echo 0 > /proc/boot_info/rootfs/primaryboot
$ cat /proc/boot_info/getbinary_bootconfig > /tmp/bootconfig.bin
$ cat /proc/boot_info/getbinary_bootconfig1 > /tmp/bootconfig1.bin
$ mtd write /tmp/bootconfig.bin /dev/mtd2
$ mtd write /tmp/bootconfig1.bin /dev/mtd3
6. Reboot the device.
$ reboot
Signed-off-by: David Bauer <mail at david-bauer.net>
(cherry picked from commit 844bb4bfad84cc6267f9b138d1f63b07ed3b77d0)
---
.../ipq40xx/base-files/etc/board.d/02_network | 1 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 6 +-
.../ipq40xx/base-files/lib/upgrade/platform.sh | 1 +
.../arch/arm/boot/dts/qcom-ipq4018-rutx50.dts | 181 +++++++++++++++++++++
target/linux/ipq40xx/image/generic.mk | 16 ++
5 files changed, 203 insertions(+), 2 deletions(-)
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 1a74fb792c..c297566dd8 100644
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -24,6 +24,7 @@ ipq40xx_setup_interfaces()
p2w,r619ac-64m|\
p2w,r619ac-128m|\
pakedge,wr-1|\
+ teltonika,rutx50|\
zyxel,nbg6617)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
;;
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 7f41bdcfcc..c8cf297e81 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -131,7 +131,8 @@ case "$FIRMWARE" in
caldata_extract "0:ART" 0x1000 0x2f20
ath10k_patch_mac $(macaddr_add $(get_mac_label) 2)
;;
- teltonika,rutx10)
+ teltonika,rutx10|\
+ teltonika,rutx50)
caldata_extract "0:ART" 0x1000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary "0:CONFIG" 0x0) 2)
;;
@@ -227,7 +228,8 @@ case "$FIRMWARE" in
caldata_extract "0:ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(get_mac_label) 4)
;;
- teltonika,rutx10)
+ teltonika,rutx10|\
+ teltonika,rutx50)
caldata_extract "0:ART" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary "0:CONFIG" 0x0) 3)
;;
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index e6e99b9d21..8807f844e5 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -207,6 +207,7 @@ platform_do_upgrade() {
sony_emmc_do_upgrade "$1"
;;
teltonika,rutx10 |\
+ teltonika,rutx50 |\
zte,mf18a |\
zte,mf286d |\
zte,mf287plus |\
diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-rutx50.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-rutx50.dts
new file mode 100644
index 0000000000..ea2102f7d6
--- /dev/null
+++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-rutx50.dts
@@ -0,0 +1,181 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4018-rutx.dtsi"
+
+/ {
+ model = "Teltonika RUTX50";
+ compatible = "teltonika,rutx50";
+
+ aliases {
+ led-boot = &led_rssi0;
+ led-failsafe = &led_rssi0;
+ led-running = &led_rssi0;
+ led-upgrade = &led_rssi0;
+ label-mac-device = &gmac;
+ };
+
+ soc {
+ gpio-export {
+ compatible = "gpio-export";
+ #size-cells = <0>;
+
+ gpio_modem_reset {
+ gpio-export,name = "modem_reset";
+ gpio-export,output = <0>;
+ gpios = <&shift_io 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ gpio_modem_power {
+ gpio-export,name = "modem_power";
+ gpio-export,output = <0>;
+ gpios = <&shift_io 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ gpio_out_1 {
+ gpio-export,name = "sim-select";
+ /* 0 = SIM1 ; 1 = SIM2 */
+ gpio-export,output = <0>;
+ gpios = <&shift_io 10 GPIO_ACTIVE_HIGH>;
+ };
+
+ gpio_in_1 {
+ gpio-export,name = "sim-detect";
+ gpio-export,input = <0>;
+ gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ label = "green:sim1";
+ gpios = <&shift_io 14 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-1 {
+ label = "green:sim2";
+ gpios = <&shift_io 15 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-2 {
+ label = "green:eth";
+ gpios = <&shift_io 6 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-3 {
+ label = "green:wifi";
+ gpios = <&shift_io 7 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-4 {
+ label = "green:3g";
+ gpios = <&shift_io 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-5 {
+ label = "green:4g";
+ gpios = <&shift_io 4 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-6 {
+ label = "green:5g";
+ gpios = <&shift_io 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_rssi0: led-7 {
+ label = "green:rssi0";
+ gpios = <&shift_io 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-8 {
+ label = "green:rssi1";
+ gpios = <&shift_io 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-9 {
+ label = "green:rssi2";
+ gpios = <&shift_io 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-10 {
+ label = "green:wifi2g";
+ gpios = <&shift_io 12 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-11 {
+ label = "green:wifi5g";
+ gpios = <&shift_io 13 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ spi-gpio {
+ compatible = "spi-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio-sck = <&tlmm 1 GPIO_ACTIVE_HIGH>;
+ gpio-mosi = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+ cs-gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+ num-chipselects = <1>;
+
+ shift_io: shift_io at 0 {
+ compatible = "fairchild,74hc595";
+ reg = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ /* Attn: This is specific to RUTX50 in Teltonika GPL */
+ registers-number = <2>;
+ spi-max-frequency = <10000000>;
+ };
+ };
+ };
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "Teltonika-RUTX10";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "Teltonika-RUTX10";
+};
+
+&gmac {
+ status = "okay";
+};
+
+&switch {
+ status = "okay";
+};
+
+&swport1 {
+ status = "okay";
+
+ label = "lan1";
+};
+
+&swport2 {
+ status = "okay";
+
+ label = "lan2";
+};
+
+&swport3 {
+ status = "okay";
+
+ label = "lan3";
+};
+
+&swport4 {
+ status = "okay";
+
+ label = "lan4";
+};
+
+&swport5 {
+ status = "okay";
+
+ label = "wan";
+};
diff --git a/target/linux/ipq40xx/image/generic.mk b/target/linux/ipq40xx/image/generic.mk
index f15463ae8c..a9dd2aa091 100644
--- a/target/linux/ipq40xx/image/generic.mk
+++ b/target/linux/ipq40xx/image/generic.mk
@@ -1076,6 +1076,22 @@ endef
# Missing DSA Setup
#TARGET_DEVICES += teltonika_rutx10
+define Device/teltonika_rutx50
+ $(call Device/FitImage)
+ $(call Device/UbiFit)
+ DEVICE_VENDOR := Teltonika
+ DEVICE_MODEL := RUTX50
+ SOC := qcom-ipq4018
+ DEVICE_DTS_CONFIG := config at 5
+ KERNEL_INSTALL := 1
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ FILESYSTEMS := squashfs
+ IMAGE/factory.ubi := append-ubi
+ DEVICE_PACKAGES := ipq-wifi-teltonika_rutx kmod-usb-net-qmi-wwan kmod-usb-serial-option uqmi
+endef
+TARGET_DEVICES += teltonika_rutx50
+
define Device/tel_x1pro
$(call Device/FitImage)
DEVICE_VENDOR := Telco
More information about the lede-commits
mailing list