[openwrt/openwrt] mediatek: add support for ZyXEL NWA50AX Pro
LEDE Commits
lede-commits at lists.infradead.org
Sun Jul 23 11:51:19 PDT 2023
blocktrron pushed a commit to openwrt/openwrt.git, branch openwrt-23.05:
https://git.openwrt.org/476bf135fcec4c1ceb5114029e539a07131e970f
commit 476bf135fcec4c1ceb5114029e539a07131e970f
Author: David Bauer <mail at david-bauer.net>
AuthorDate: Sat Jul 15 18:10:31 2023 +0200
mediatek: add support for ZyXEL NWA50AX Pro
Hardware
--------
CPU: Mediatek MT7981
RAM: 512M DDR4
FLASH: 256M NAND
ETH: MaxLinear GPY211 (2.5GbE N Base-T)
WiFi: Mediatek MT7981 (2.4GHz 2T2R:2 5GHz 3T3R:2 802.11ax)
BTN: 1x Reset
LED: 1x Multi-Color
UART Console
------------
Available below the rubber cover next to the ethernet port.
Settings: 115200 8N1
Layout:
<12V> <LAN> GND-RX-TX-VCC
Logic-Level is 3V3. Don't connect VCC to your UART adapter!
Installation Web-UI
-------------------
Upload the Factory image using the devices Web-Interface.
As the device uses a dual-image partition layout, OpenWrt can only
installed on Slot A. This requires the current active image prior
flashing the device to be on Slot B.
In case this is not the case, OpenWrt will boot only one time, returning
to the ZyXEL firmware the second boot.
If this happens, first install a ZyXEL firmware upgrade of any version
and install OpenWrt after that.
Installation TFTP / Recovery
----------------------------
This installation routine is especially useful in case of a bricked
device.
Attach to the UART console header of the device. Interrupt the boot
procedure by pressing Enter.
The bootloader has a reduced command-set available from CLI, but more
commands can be executed by abusing the atns command.
Boot a OpenWrt initramfs image available on a TFTP server at
192.168.1.66. Rename the image to nwa50axpro-openwrt-initramfs.bin.
$ atnf nwa50axpro-openwrt-initramfs.bin
$ atna 192.168.1.88
$ atns "192.168.1.66; tftpboot; setenv fdt_high 0xffffffffffffffff;
bootm"
Upon booting, set the booted image to the correct slot:
$ zyxel-bootconfig /dev/mtd9 get-status
$ zyxel-bootconfig /dev/mtd9 set-image-status 0 valid
$ zyxel-bootconfig /dev/mtd9 set-active-image 0
Copy the OpenWrt sysupgrade image to the device using scp.
Write the sysupgrade image to NAND using sysupgrade.
$ sysupgrade -n image.bin
Signed-off-by: David Bauer <mail at david-bauer.net>
(cherry picked from commit f0445746f6fd96fc7c5394b238153bd2ff22bc5b)
---
.../zyxel-bootconfig/files/95_apply_bootconfig | 1 +
scripts/mkits-zyxel-fit-filogic.sh | 40 ++++
.../mediatek/dts/mt7981b-zyxel-nwa50ax-pro.dts | 225 +++++++++++++++++++++
.../filogic/base-files/etc/board.d/02_network | 3 +-
.../etc/hotplug.d/ieee80211/11_fix_wifi_mac | 5 +
target/linux/mediatek/image/filogic.mk | 25 +++
6 files changed, 298 insertions(+), 1 deletion(-)
diff --git a/package/utils/zyxel-bootconfig/files/95_apply_bootconfig b/package/utils/zyxel-bootconfig/files/95_apply_bootconfig
index 500b81234a..c98bc8fbe2 100644
--- a/package/utils/zyxel-bootconfig/files/95_apply_bootconfig
+++ b/package/utils/zyxel-bootconfig/files/95_apply_bootconfig
@@ -3,6 +3,7 @@ apply_bootconfig() {
case $(board_name) in
zyxel,nwa50ax|\
+ zyxel,nwa50ax-pro|\
zyxel,nwa55axe)
mtd_idx=$(find_mtd_index "bootconfig")
zyxel-bootconfig "/dev/mtd$mtd_idx" set-image-status 0 valid
diff --git a/scripts/mkits-zyxel-fit-filogic.sh b/scripts/mkits-zyxel-fit-filogic.sh
new file mode 100755
index 0000000000..319e187f5a
--- /dev/null
+++ b/scripts/mkits-zyxel-fit-filogic.sh
@@ -0,0 +1,40 @@
+#!/usr/bin/env bash
+#
+# Licensed under the terms of the GNU GPL License version 2 or later.
+# Author: David Bauer <mail at david-bauer.net>, based on mkits-zyxel-factory.sh.
+
+usage() {
+ echo "Usage: `basename $0` output file compat-models"
+ exit 1
+}
+
+# We need at least 3 arguments
+[ "$#" -lt 3 ] && usage
+
+# Target output file
+OUTPUT="$1"; shift
+FILE="$1"; shift
+MODELS="$1"; shift
+
+# Create a default, fully populated DTS file
+echo "\
+/dts-v1/;
+
+/ {
+ timestamp = <0x684090B4>;
+ description = \"Zyxel FIT (Flattened Image Tree)\";
+ compat-models = [${MODELS}];
+ fw_version = \"9.99(###.1)\";
+ #address-cells = <1>;
+
+ images {
+ ubi {
+ data = /incbin/(\"${FILE}\");
+ type = \"firmware\";
+ compression = \"none\";
+ hash {
+ algo = \"sha256\";
+ };
+ };
+ };
+};" > ${OUTPUT}
diff --git a/target/linux/mediatek/dts/mt7981b-zyxel-nwa50ax-pro.dts b/target/linux/mediatek/dts/mt7981b-zyxel-nwa50ax-pro.dts
new file mode 100644
index 0000000000..75dd84c9d7
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7981b-zyxel-nwa50ax-pro.dts
@@ -0,0 +1,225 @@
+/dts-v1/;
+
+#include "mt7981.dtsi"
+
+/ {
+ model = "ZyXEL NWA50AX Pro";
+ compatible = "zyxel,nwa50ax-pro", "mediatek,mt7981";
+
+ aliases {
+ led-boot = &led_green;
+ led-failsafe = &led_red;
+ led-running = &led_green;
+ led-upgrade = &led_red;
+ serial0 = &uart0;
+ label-mac-device = &gmac1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&pio 1 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_green: led at 0 {
+ label = "green:system";
+ gpios = <&pio 4 GPIO_ACTIVE_HIGH>;
+ };
+
+ led at 1 {
+ label = "blue:system";
+ gpios = <&pio 6 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_red: led at 2 {
+ label = "red:system";
+ gpios = <&pio 7 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+ð {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio_pins>;
+
+ status = "okay";
+
+ gmac1: mac at 1 {
+ compatible = "mediatek,eth-mac";
+ reg = <1>;
+ phy-mode = "2500base-x";
+
+ phy-handle = <&phy0>;
+
+ nvmem-cells = <&macaddr_mrd_1fff8>;
+ nvmem-cell-names = "mac-address";
+ };
+};
+
+&mdio_bus {
+ reset-gpios = <&pio 12 GPIO_ACTIVE_LOW>;
+ reset-delay-us = <1500000>;
+ reset-post-delay-us = <1000000>;
+
+ phy0: ethernet-phy at 5 {
+ reg = <5>;
+ compatible = "ethernet-phy-ieee802.3-c45";
+ };
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_flash_pins>;
+ status = "okay";
+
+ spi_nand: flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-nand";
+ reg = <0>;
+ spi-max-frequency = <52000000>;
+
+ spi-cal-enable;
+ spi-cal-mode = "read-data";
+ spi-cal-datalen = <7>;
+ spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>;
+ spi-cal-addrlen = <5>;
+ spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;
+
+ spi-tx-buswidth = <4>;
+ spi-rx-buswidth = <4>;
+ mediatek,nmbm;
+ mediatek,bmt-max-ratio = <1>;
+ mediatek,bmt-max-reserved-blocks = <64>;
+
+ mediatek,bmt-remap-range =
+ <0x0 0x580000>,
+ <0xef00000 0xef80000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "BL2";
+ reg = <0x00000 0x0100000>;
+ read-only;
+ };
+
+ partition at 100000 {
+ label = "u-boot-env";
+ reg = <0x0100000 0x0080000>;
+ };
+
+ factory: partition at 180000 {
+ label = "Factory";
+ reg = <0x180000 0x0200000>;
+ read-only;
+
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr: macaddr at a {
+ reg = <0xa 0x6>;
+ };
+ };
+
+ partition at 380000 {
+ label = "FIP";
+ reg = <0x380000 0x0200000>;
+ read-only;
+ };
+
+ partition at 580000 {
+ label = "ubi";
+ reg = <0x580000 0x3200000>;
+ };
+
+ partition at 3780000 {
+ label = "ubi_1";
+ reg = <0x3780000 0x3200000>;
+ read-only;
+ };
+
+ partition at 6980000 {
+ label = "rootfs-data";
+ reg = <0x6980000 0x3c00000>;
+ read-only;
+ };
+
+ partition at a580000 {
+ label = "logs";
+ reg = <0xa580000 0x3a80000>;
+ read-only;
+ };
+
+ partition at e000000 {
+ label = "myzyxel";
+ reg = <0xe000000 0xf00000>;
+ read-only;
+ };
+
+ partition at ef00000 {
+ label = "bootconfig";
+ reg = <0xef00000 0x80000>;
+ };
+
+ partition at ef80000 {
+ label = "mrd";
+ reg = <0xef80000 0x80000>;
+ read-only;
+
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_mrd_1fff8: macaddr at 1fff8 {
+ reg = <0x1fff8 0x6>;
+ };
+ };
+ };
+ };
+};
+
+&pio {
+ spi0_flash_pins: spi0-pins {
+ mux {
+ function = "spi";
+ groups = "spi0", "spi0_wp_hold";
+ };
+ };
+
+ pwm_pins: pwm0-pins {
+ mux {
+ function = "pwm";
+ groups = "pwm0_1";
+ };
+ };
+};
+
+&wifi {
+ status = "okay";
+
+ mediatek,mtd-eeprom = <&factory 0x0>;
+};
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
index 6abc81a0b0..3b170ddc18 100644
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
@@ -11,7 +11,8 @@ mediatek_setup_interfaces()
asus,tuf-ax4200)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" eth1
;;
- netgear,wax220)
+ netgear,wax220|\
+ zyxel,nwa50ax-pro)
ucidef_set_interface_lan "eth0"
;;
bananapi,bpi-r3)
diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
index ab23b10044..3620e3a6fb 100644
--- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
+++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
@@ -61,4 +61,9 @@ case "$board" in
addr=$(mtd_get_mac_binary "Factory" 0x4)
[ "$PHYNBR" = "1" ] && macaddr_add $addr 1 > /sys${DEVPATH}/macaddress
;;
+ zyxel,nwa50ax-pro)
+ hw_mac_addr="$(mtd_get_mac_binary mrd 0x1fff8)"
+ [ "$PHYNBR" = "0" ] && macaddr_add $hw_mac_addr 1 > /sys${DEVPATH}/macaddress
+ [ "$PHYNBR" = "1" ] && macaddr_add $hw_mac_addr 2 > /sys${DEVPATH}/macaddress
+ ;;
esac
diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk
index 8d5caad113..c41cba3a64 100644
--- a/target/linux/mediatek/image/filogic.mk
+++ b/target/linux/mediatek/image/filogic.mk
@@ -75,6 +75,13 @@ define Build/append-gl-metadata
}
endef
+define Build/zyxel-nwa-fit-filogic
+ $(TOPDIR)/scripts/mkits-zyxel-fit-filogic.sh \
+ $@.its $@ "80 e1 ff ff ff ff ff ff ff ff"
+ PATH=$(LINUX_DIR)/scripts/dtc:$(PATH) mkimage -f $@.its $@.new
+ @mv $@.new $@
+endef
+
define Device/asus_tuf-ax4200
DEVICE_VENDOR := ASUS
DEVICE_MODEL := TUF-AX4200
@@ -424,3 +431,21 @@ define Device/zyxel_ex5601-t0-stock
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd
endef
TARGET_DEVICES += zyxel_ex5601-t0-stock
+
+define Device/zyxel_nwa50ax-pro
+ DEVICE_VENDOR := ZyXEL
+ DEVICE_MODEL := NWA50AX Pro
+ DEVICE_DTS := mt7981b-zyxel-nwa50ax-pro
+ DEVICE_DTS_DIR := ../dts
+ DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware zyxel-bootconfig
+ DEVICE_DTS_LOADADDR := 0x44000000
+ UBINIZE_OPTS := -E 5
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ IMAGE_SIZE := 51200k
+ KERNEL_IN_UBI := 1
+ IMAGES += factory.bin
+ IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE) | zyxel-nwa-fit-filogic
+ IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+endef
+TARGET_DEVICES += zyxel_nwa50ax-pro
More information about the lede-commits
mailing list