[openwrt/openwrt] ipq807x: add Dynalink DL-WRX36
LEDE Commits
lede-commits at lists.infradead.org
Mon Jan 16 03:53:06 PST 2023
ansuel pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/26c095cb4d27428acedf1b738507a585f1585fe4
commit 26c095cb4d27428acedf1b738507a585f1585fe4
Author: Dirk Buchwalder <buchwalder at posteo.de>
AuthorDate: Fri Aug 5 11:38:37 2022 +0200
ipq807x: add Dynalink DL-WRX36
Dynalink DL-WRX36 is a AX WIFI router with 4 1G and 1 2.5G ports.
Specifications:
• CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz
• RAM: 1024MB of DDR3
• Storage: 256MB Nand
• Ethernet: 4x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081)
• WLAN:
2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 1174 Mbps PHY rate
5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate
• 1x USB 3.0
• 1 gpio-controlled dual color led (blue/red)
• Buttons: 1x soft reset / 1x WPS
• Power: 12V DC jack
A poulated serial header is onboard (J1004)
the connector size is a 4-pin 2.0 mm JST PH.
RX/TX is working, u-boot bootwait is active, secure boot is enabled.
Notes:
- Serial is completely deactivated in the stock firmware image.
- This commit adds only single partition support, that means
sysupgrade is upgrading the current rootfs partition.
- Installation can be done by serial connection or
SSH access on OEM firmware
Installation Instructions:
Most part of the installation is performed from an initramfs image
running OpenWrt, and there are two options to boot it.
Boot initramfs option 1: Using serial connection (3.3V)
1. Stop auto boot to get to U-boot shell
2. Transfer initramfs image to device
(openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb)
Tested using TFTP and a FAT-formatted USB flash drive.
3. Boot the initramfs image
# bootm
Boot initramfs option 2: From SSH access on OEM firmware
1. Copy the initramfs image to a FAT-formatted flash drive
(tested on single-partition drive) and connect it to device USB port.
2. Change boot command so it loads the initramfs image on next boot
Fallback to OEM firmware is provided.
# fw_setenv bootcmd 'usb start && fatload usb 0:1 0x44000000 openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb && bootm 0x44000000; bootipq'
3. Reboot the device to boot the initramfs
# reboot
Install OpenWrt from initramfs image:
1. Use SCP (or other way) to transfer OpenWrt factory image
2. Connect to device using SSH (on a LAN port)
3. Check MTD partition table.
rootfs and rootfs_1 should be mtd18 and mtd20
depending on current OEM slot.
# cat /proc/mtd
4. Do a ubiformat to both rootfs partitions:
# ubiformat /dev/mtd18 -y -f /path_to/factory_image
# ubiformat /dev/mtd20 -y -f /path_to/factory_image
5. Set U-boot env variable: mtdids
# fw_setenv mtdids 'nand0=nand0'
6. Get offset of mtd18 to determine current OEM slot
- If current OEM slot is 1, offset is 16777216 (0x1000000)
- If current OEM slot is 2, offset is 127926272 (0x7a00000)
# cat /sys/class/mtd/mtd18/offset
7. Set U-boot env variable: mtdparts
If current OEM slot is 1, run:
# fw_setenv mtdparts 'mtdparts=nand0:0x6100000 at 0x1000000(fs),0x6100000 at 0x7a00000(fs_1)'
If current OEM slot is 2, run:
# fw_setenv mtdparts 'mtdparts=nand0:0x6100000 at 0x7a00000(fs),0x6100000 at 0x1000000(fs_1)'
8. Set U-boot env variable: bootcmd
# fw_setenv bootcmd 'setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs rootfstype=squashfs rootwait; ubi part fs; ubi read 0x44000000 kernel; bootm 0x44000000#config at rt5010w-d350-rev0'
9. Reboot the device
# reboot
Note: this PR adds only single partition support, that means sysupgrade is
upgrading the current rootfs partition
Signed-off-by: Dirk Buchwalder <buchwalder at posteo.de>
---
package/boot/uboot-envtools/files/ipq807x | 5 +
package/firmware/ipq-wifi/Makefile | 2 +
.../ipq-wifi/board-dynalink_dl-wrx36.ipq8074 | Bin 0 -> 131180 bytes
.../ipq807x/base-files/etc/board.d/02_network | 3 +
.../etc/hotplug.d/firmware/11-ath11k-caldata | 1 +
.../ipq807x/base-files/lib/upgrade/platform.sh | 3 +
.../arch/arm64/boot/dts/qcom/ipq8072-dl-wrx36.dts | 243 +++++++++++++++++++++
target/linux/ipq807x/image/generic.mk | 13 ++
8 files changed, 270 insertions(+)
diff --git a/package/boot/uboot-envtools/files/ipq807x b/package/boot/uboot-envtools/files/ipq807x
index 71fa7b7b79..63fd04ec5b 100644
--- a/package/boot/uboot-envtools/files/ipq807x
+++ b/package/boot/uboot-envtools/files/ipq807x
@@ -8,6 +8,11 @@ touch /etc/config/ubootenv
board=$(board_name)
case "$board" in
+dynalink,dl-wrx36)
+ idx="$(find_mtd_index 0:appsblenv)"
+ [ -n "$idx" ] && \
+ ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x40000" "0x20000" "2"
+ ;;
edgecore,eap102)
idx="$(find_mtd_index 0:appsblenv)"
[ -n "$idx" ] && \
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile
index e662f7408a..32988910c0 100644
--- a/package/firmware/ipq-wifi/Makefile
+++ b/package/firmware/ipq-wifi/Makefile
@@ -27,6 +27,7 @@ endef
ALLWIFIBOARDS:= \
aruba_ap-365 \
devolo_magic-2-wifi-next \
+ dynalink_dl-wrx36 \
edgecore_eap102 \
edgecore_ecw5410 \
edgecore_oap100 \
@@ -124,6 +125,7 @@ endef
$(eval $(call generate-ipq-wifi-package,aruba_ap-365,Aruba AP-365))
$(eval $(call generate-ipq-wifi-package,devolo_magic-2-wifi-next,devolo Magic 2 WiFi next))
+$(eval $(call generate-ipq-wifi-package,dynalink_dl-wrx36,Dynalink DL-WRX36))
$(eval $(call generate-ipq-wifi-package,edgecore_eap102,Edgecore EAP102))
$(eval $(call generate-ipq-wifi-package,edgecore_ecw5410,Edgecore ECW5410))
$(eval $(call generate-ipq-wifi-package,edgecore_oap100,Edgecore OAP100))
diff --git a/package/firmware/ipq-wifi/board-dynalink_dl-wrx36.ipq8074 b/package/firmware/ipq-wifi/board-dynalink_dl-wrx36.ipq8074
new file mode 100644
index 0000000000..e529000c68
Binary files /dev/null and b/package/firmware/ipq-wifi/board-dynalink_dl-wrx36.ipq8074 differ
diff --git a/target/linux/ipq807x/base-files/etc/board.d/02_network b/target/linux/ipq807x/base-files/etc/board.d/02_network
index 8856daff31..e2bd46f095 100644
--- a/target/linux/ipq807x/base-files/etc/board.d/02_network
+++ b/target/linux/ipq807x/base-files/etc/board.d/02_network
@@ -11,6 +11,9 @@ ipq807x_setup_interfaces()
local board="$1"
case "$board" in
+ dynalink,dl-wrx36)
+ ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
+ ;;
edgecore,eap102)
ucidef_set_interfaces_lan_wan "lan" "wan"
;;
diff --git a/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata b/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
index a2290ac124..974e7607aa 100644
--- a/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
+++ b/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
@@ -11,6 +11,7 @@ case "$FIRMWARE" in
case "$board" in
edgecore,eap102|\
edimax,cax1800|\
+ dynalink,dl-wrx36|\
qnap,301w|\
redmi,ax6|\
xiaomi,ax3600|\
diff --git a/target/linux/ipq807x/base-files/lib/upgrade/platform.sh b/target/linux/ipq807x/base-files/lib/upgrade/platform.sh
index ab3121c44f..63f546444f 100644
--- a/target/linux/ipq807x/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq807x/base-files/lib/upgrade/platform.sh
@@ -43,6 +43,9 @@ platform_pre_upgrade() {
platform_do_upgrade() {
case "$(board_name)" in
+ dynalink,dl-wrx36)
+ nand_do_upgrade "$1"
+ ;;
edgecore,eap102)
active="$(fw_printenv -n active)"
if [ "$active" -eq "1" ]; then
diff --git a/target/linux/ipq807x/files/arch/arm64/boot/dts/qcom/ipq8072-dl-wrx36.dts b/target/linux/ipq807x/files/arch/arm64/boot/dts/qcom/ipq8072-dl-wrx36.dts
new file mode 100644
index 0000000000..5468e9e1fb
--- /dev/null
+++ b/target/linux/ipq807x/files/arch/arm64/boot/dts/qcom/ipq8072-dl-wrx36.dts
@@ -0,0 +1,243 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2022, Robert Marko <robimarko at gmail.com> */
+
+/dts-v1/;
+
+#include "ipq8074.dtsi"
+#include "ipq8074-hk-cpu.dtsi"
+#include "ipq8074-ess.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Dynalink DL-WRX36";
+ compatible = "dynalink,dl-wrx36", "qcom,ipq8074";
+
+ aliases {
+ led-boot = &led_system_red;
+ led-failsafe = &led_system_red;
+ led-running = &led_system_blue;
+ led-upgrade = &led_system_red;
+ serial0 = &blsp1_uart5;
+ /* Aliases as required by u-boot to patch MAC addresses */
+ ethernet0 = &dp6_syn;
+ ethernet1 = &dp4;
+ ethernet2 = &dp3;
+ ethernet3 = &dp2;
+ ethernet4 = &dp1;
+ label-mac-device = &dp6_syn;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs-append = " root=/dev/ubiblock0_1";
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_system_blue: system-blue {
+ label = "blue:system";
+ gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>;
+ color = <LED_COLOR_ID_BLUE>;
+ };
+
+ led_system_red: system-red {
+ label = "red:system";
+ gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>;
+ color = <LED_COLOR_ID_RED>;
+ };
+ };
+};
+
+&tlmm {
+ mdio_pins: mdio-pins {
+ mdc {
+ pins = "gpio68";
+ function = "mdc";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ mdio {
+ pins = "gpio69";
+ function = "mdio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+};
+
+&blsp1_uart5 {
+ status = "okay";
+};
+
+&prng {
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&crypto {
+ status = "okay";
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&qpic_nand {
+ status = "okay";
+
+ nand at 0 {
+ reg = <0>;
+ nand-ecc-strength = <8>;
+ nand-ecc-step-size = <512>;
+ nand-bus-width = <8>;
+
+ partitions {
+ compatible = "qcom,smem-part";
+ };
+ };
+};
+
+&qusb_phy_0 {
+ status = "okay";
+};
+
+&ssphy_0 {
+ status = "okay";
+};
+
+&usb_0 {
+ status = "okay";
+};
+
+&mdio {
+ status = "okay";
+
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>;
+
+ qca8075_0: ethernet-phy at 0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+
+ qca8075_1: ethernet-phy at 1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+
+ qca8075_2: ethernet-phy at 2 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <2>;
+ };
+
+ qca8075_3: ethernet-phy at 3 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <3>;
+ };
+
+ qca8081: ethernet-phy at 28 {
+ compatible = "ethernet-phy-id004d.d101";
+ reg = <28>;
+ reset-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&switch {
+ status = "okay";
+
+ switch_cpu_bmp = <0x1>; /* cpu port bitmap */
+ switch_lan_bmp = <0x3e>; /* lan port bitmap */
+ switch_wan_bmp = <0x40>; /* wan port bitmap */
+ switch_mac_mode = <0xb>; /* mac mode for uniphy instance0*/
+ switch_mac_mode1 = <0xff>; /* mac mode for uniphy instance1*/
+ switch_mac_mode2 = <0xc>; /* mac mode for uniphy instance2*/
+ bm_tick_mode = <0>; /* bm tick mode */
+ tm_tick_mode = <0>; /* tm tick mode */
+
+ qcom,port_phyinfo {
+ port at 0 {
+ port_id = <1>;
+ phy_address = <0>;
+ };
+ port at 1 {
+ port_id = <2>;
+ phy_address = <1>;
+ };
+ port at 2 {
+ port_id = <3>;
+ phy_address = <2>;
+ };
+ port at 3 {
+ port_id = <4>;
+ phy_address = <3>;
+ };
+ port at 5 {
+ port_id = <6>;
+ phy_address = <28>;
+ port_mac_sel = "QGMAC_PORT";
+ };
+ };
+};
+
+&edma {
+ status = "okay";
+};
+
+&dp1 {
+ status = "okay";
+ phy-handle = <&qca8075_0>;
+ label = "lan4";
+};
+
+&dp2 {
+ status = "okay";
+ phy-handle = <&qca8075_1>;
+ label = "lan3";
+};
+
+&dp3 {
+ status = "okay";
+ phy-handle = <&qca8075_2>;
+ label = "lan2";
+};
+
+&dp4 {
+ status = "okay";
+ phy-handle = <&qca8075_3>;
+ label = "lan1";
+};
+
+&dp6_syn {
+ status = "okay";
+ phy-handle = <&qca8081>;
+ label = "wan";
+};
+
+&wifi {
+ status = "okay";
+ qcom,ath11k-calibration-variant = "Dynalink-DL-WRX36";
+};
diff --git a/target/linux/ipq807x/image/generic.mk b/target/linux/ipq807x/image/generic.mk
index 23260ed1e7..811a32e942 100644
--- a/target/linux/ipq807x/image/generic.mk
+++ b/target/linux/ipq807x/image/generic.mk
@@ -17,6 +17,19 @@ define Device/UbiFit
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
+define Device/dynalink_dl-wrx36
+ $(call Device/FitImage)
+ $(call Device/UbiFit)
+ DEVICE_VENDOR := Dynalink
+ DEVICE_MODEL := DL-WRX36
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ DEVICE_DTS_CONFIG := config at rt5010w-d350-rev0
+ SOC := ipq8072
+ DEVICE_PACKAGES := ipq-wifi-dynalink_dl-wrx36
+endef
+TARGET_DEVICES += dynalink_dl-wrx36
+
define Device/edgecore_eap102
$(call Device/FitImage)
$(call Device/UbiFit)
More information about the lede-commits
mailing list