[openwrt/openwrt] ipq807x: add Xiaomi AX3600
LEDE Commits
lede-commits at lists.infradead.org
Mon Jan 16 03:53:00 PST 2023
ansuel pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/8364f0816417bfe404f7bded4eaa4f4a60c6d006
commit 8364f0816417bfe404f7bded4eaa4f4a60c6d006
Author: Robert Marko <robimarko at gmail.com>
AuthorDate: Wed May 19 21:04:43 2021 +0200
ipq807x: add Xiaomi AX3600
Xiaomi AX3600 is a budget 802.11ax dual-band router/AP.
Specifications:
* CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz
* RAM: 512MB of DDR3
* Storage: 256MB of parallel NAND
* Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port
* WLAN:
* PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT
* 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: Qualcomm QCN5054 4x4 at 80MHz or 2x2 at 160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate
* LED-s:
* System (Blue and Yellow)
* IoT (Blue)
* Network (Blue and Yellow)
* Buttons: 1x Soft reset
* Power: 12V DC Jack
Installation instructions:
Obtaining SSH access is mandatory
https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access
Installation is done by the ubiformat method, through SSH:
1. Open an SSH shell to the router
2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory
3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
4. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd12 and mtd13 are the correct indexes from above!
5. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
6. Reboot the device by:
reboot
Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step
since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages.
Continue in order to pernamently flash OpenWrt:
7. SSH into OpenWrt from one of the LAN ports
8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory
9. Sysupgrade the device:
sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: Christian Marangi <ansuelsmth at gmail.com>
Signed-off-by: Robert Marko <robimarko at gmail.com>
---
package/boot/uboot-envtools/files/ipq807x | 24 ++
package/firmware/ipq-wifi/Makefile | 17 +-
.../firmware/ipq-wifi/board-xiaomi_ax3600.ipq8074 | Bin 0 -> 131176 bytes
.../firmware/ipq-wifi/board-xiaomi_ax3600.qca9889 | Bin 0 -> 2260 bytes
.../linux/ipq807x/base-files/etc/board.d/01_leds | 16 ++
.../ipq807x/base-files/etc/board.d/02_network | 28 ++
.../etc/hotplug.d/firmware/11-ath11k-caldata | 20 ++
.../ipq807x/base-files/lib/upgrade/platform.sh | 65 +++++
.../arch/arm64/boot/dts/qcom/ipq8071-ax3600.dts | 73 +++++
.../arch/arm64/boot/dts/qcom/ipq8071-ax3600.dtsi | 311 +++++++++++++++++++++
target/linux/ipq807x/image/generic.mk | 18 ++
11 files changed, 569 insertions(+), 3 deletions(-)
diff --git a/package/boot/uboot-envtools/files/ipq807x b/package/boot/uboot-envtools/files/ipq807x
new file mode 100644
index 0000000000..bf116d1fca
--- /dev/null
+++ b/package/boot/uboot-envtools/files/ipq807x
@@ -0,0 +1,24 @@
+[ -e /etc/config/ubootenv ] && exit 0
+
+touch /etc/config/ubootenv
+
+. /lib/uboot-envtools.sh
+. /lib/functions.sh
+
+board=$(board_name)
+
+case "$board" in
+xiaomi,ax3600)
+ idx="$(find_mtd_index 0:appsblenv)"
+ [ -n "$idx" ] && \
+ ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x10000" "0x20000"
+ idx2="$(find_mtd_index bdata)"
+ [ -n "$idx2" ] && \
+ ubootenv_add_uci_sys_config "/dev/mtd$idx2" "0x0" "0x10000" "0x20000"
+ ;;
+esac
+
+config_load ubootenv
+config_foreach ubootenv_add_app_config
+
+exit 0
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile
index 56c799302e..9b490e6f74 100644
--- a/package/firmware/ipq-wifi/Makefile
+++ b/package/firmware/ipq-wifi/Makefile
@@ -41,6 +41,7 @@ ALLWIFIBOARDS:= \
qxwlan_e2600ac-c2 \
sony_ncp-hg100-cellular \
teltonika_rutx \
+ xiaomi_ax3600 \
zte_mf18a \
zte_mf289f
@@ -50,7 +51,7 @@ define Package/ipq-wifi-default
SUBMENU:=ath10k Board-Specific Overrides
SECTION:=firmware
CATEGORY:=Firmware
- DEPENDS:=@(TARGET_ipq40xx||TARGET_ipq806x)
+ DEPENDS:=@(TARGET_ipq40xx||TARGET_ipq806x||TARGET_ipq807x)
TITLE:=Custom Board
endef
@@ -59,17 +60,26 @@ define ipq-wifi-install-one-to
$(INSTALL_DATA) $(1) $(2)/lib/firmware/ath10k/$(3)/board-2.bin
endef
+define ipq-wifi-install-ath11-one-to
+ $(INSTALL_DIR) $(2)/lib/firmware/ath11k/$(3)/
+ $(INSTALL_DATA) $(1) $(2)/lib/firmware/ath11k/$(3)/board-2.bin
+endef
+
define ipq-wifi-install-one
$(if $(filter $(suffix $(1)),.QCA4019 .qca4019),\
$(call ipq-wifi-install-one-to,$(1),$(2),QCA4019/hw1.0),\
$(if $(filter $(suffix $(1)),.QCA9888 .qca9888),\
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9888/hw2.0),\
+ $(if $(filter $(suffix $(1)),.QCA9889 .qca9889),\
+ $(call ipq-wifi-install-one-to,$(1),$(2),QCA9887/hw1.0),\
$(if $(filter $(suffix $(1)),.QCA9984 .qca9984),\
$(call ipq-wifi-install-one-to,$(1),$(2),QCA9984/hw1.0),\
$(if $(filter $(suffix $(1)),.QCA99X0 .qca99x0),\
$(call ipq-wifi-install-one-to,$(1),$(2),QCA99X0/hw2.0),\
+ $(if $(filter $(suffix $(1)),.IPQ8074 .ipq8074),\
+ $(call ipq-wifi-install-ath11-one-to,$(1),$(2),IPQ8074/hw2.0),\
$(error Unrecognized board-file suffix '$(suffix $(1))' for '$(1)')\
- ))))
+ ))))))
endef
# Blank line required at end of above define due to foreach context
@@ -102,7 +112,7 @@ Do not install it for any other device!
endef
# Add board name to ALLWIFIBOARDS
-# Place files in this directory as board-<devicename>.<qca4019|qca9888|qca9984|qca99x0>
+# Place files in this directory as board-<devicename>.<qca4019|qca9888|qca9889|qca9984|qca99x0|ipq8074>
# Add $(eval $(call generate-ipq-wifi-package,<devicename>,<display name>))
$(eval $(call generate-ipq-wifi-package,aruba_ap-365,Aruba AP-365))
@@ -121,6 +131,7 @@ $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac-c1,Qxwlan E2600AC C1))
$(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac-c2,Qxwlan E2600AC C2))
$(eval $(call generate-ipq-wifi-package,sony_ncp-hg100-cellular,Sony NCP-HG100/Cellular))
$(eval $(call generate-ipq-wifi-package,teltonika_rutx,Teltonika RUTX))
+$(eval $(call generate-ipq-wifi-package,xiaomi_ax3600,Xiaomi AX3600))
$(eval $(call generate-ipq-wifi-package,zte_mf18a,ZTE MF18A))
$(eval $(call generate-ipq-wifi-package,zte_mf289f,ZTE MF289F))
diff --git a/package/firmware/ipq-wifi/board-xiaomi_ax3600.ipq8074 b/package/firmware/ipq-wifi/board-xiaomi_ax3600.ipq8074
new file mode 100644
index 0000000000..fd37fe8eb1
Binary files /dev/null and b/package/firmware/ipq-wifi/board-xiaomi_ax3600.ipq8074 differ
diff --git a/package/firmware/ipq-wifi/board-xiaomi_ax3600.qca9889 b/package/firmware/ipq-wifi/board-xiaomi_ax3600.qca9889
new file mode 100644
index 0000000000..af4405cd53
Binary files /dev/null and b/package/firmware/ipq-wifi/board-xiaomi_ax3600.qca9889 differ
diff --git a/target/linux/ipq807x/base-files/etc/board.d/01_leds b/target/linux/ipq807x/base-files/etc/board.d/01_leds
new file mode 100644
index 0000000000..215ab7ca21
--- /dev/null
+++ b/target/linux/ipq807x/base-files/etc/board.d/01_leds
@@ -0,0 +1,16 @@
+
+. /lib/functions/uci-defaults.sh
+
+board_config_update
+
+board=$(board_name)
+
+case "$board" in
+xiaomi,ax3600)
+ ucidef_set_led_netdev "wan" "WAN" "blue:network" "wan"
+ ;;
+esac
+
+board_config_flush
+
+exit 0
diff --git a/target/linux/ipq807x/base-files/etc/board.d/02_network b/target/linux/ipq807x/base-files/etc/board.d/02_network
new file mode 100644
index 0000000000..4dc118ed29
--- /dev/null
+++ b/target/linux/ipq807x/base-files/etc/board.d/02_network
@@ -0,0 +1,28 @@
+#
+# Copyright (c) 2015 The Linux Foundation. All rights reserved.
+# Copyright (c) 2011-2015 OpenWrt.org
+#
+
+. /lib/functions/uci-defaults.sh
+. /lib/functions/system.sh
+
+ipq807x_setup_interfaces()
+{
+ local board="$1"
+
+ case "$board" in
+ xiaomi,ax3600)
+ ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan"
+ ;;
+ *)
+ echo "Unsupported hardware. Network interfaces not initialized"
+ ;;
+ esac
+}
+
+board_config_update
+board=$(board_name)
+ipq807x_setup_interfaces $board
+board_config_flush
+
+exit 0
diff --git a/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata b/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
new file mode 100644
index 0000000000..578ff7ad45
--- /dev/null
+++ b/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
@@ -0,0 +1,20 @@
+#!/bin/sh
+
+[ -e /lib/firmware/$FIRMWARE ] && exit 0
+
+. /lib/functions/caldata.sh
+
+board=$(board_name)
+
+case "$FIRMWARE" in
+"ath11k/IPQ8074/hw2.0/cal-ahb-c000000.wifi.bin")
+ case "$board" in
+ xiaomi,ax3600)
+ caldata_extract "0:art" 0x1000 0x20000
+ ;;
+ esac
+ ;;
+*)
+ exit 1
+ ;;
+esac
diff --git a/target/linux/ipq807x/base-files/lib/upgrade/platform.sh b/target/linux/ipq807x/base-files/lib/upgrade/platform.sh
new file mode 100644
index 0000000000..d63e71251b
--- /dev/null
+++ b/target/linux/ipq807x/base-files/lib/upgrade/platform.sh
@@ -0,0 +1,65 @@
+PART_NAME=firmware
+REQUIRE_IMAGE_METADATA=1
+
+RAMFS_COPY_BIN='fw_printenv fw_setenv'
+RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
+
+xiaomi_initramfs_prepare() {
+ # Wipe UBI if running initramfs
+ [ "$(rootfs_type)" = "tmpfs" ] || return 0
+
+ local rootfs_mtdnum="$( find_mtd_index rootfs )"
+ if [ ! "$rootfs_mtdnum" ]; then
+ echo "unable to find mtd partition rootfs"
+ return 1
+ fi
+
+ local kern_mtdnum="$( find_mtd_index ubi_kernel )"
+ if [ ! "$kern_mtdnum" ]; then
+ echo "unable to find mtd partition ubi_kernel"
+ return 1
+ fi
+
+ ubidetach -m "$rootfs_mtdnum"
+ ubiformat /dev/mtd$rootfs_mtdnum -y
+
+ ubidetach -m "$kern_mtdnum"
+ ubiformat /dev/mtd$kern_mtdnum -y
+}
+
+platform_check_image() {
+ return 0;
+}
+
+platform_pre_upgrade() {
+ case "$(board_name)" in
+ xiaomi,ax3600)
+ xiaomi_initramfs_prepare
+ ;;
+ esac
+}
+
+platform_do_upgrade() {
+ case "$(board_name)" in
+ xiaomi,ax3600)
+ # Make sure that UART is enabled
+ fw_setenv boot_wait on
+ fw_setenv uart_en 1
+
+ # Enforce single partition.
+ fw_setenv flag_boot_rootfs 0
+ fw_setenv flag_last_success 0
+ fw_setenv flag_boot_success 1
+ fw_setenv flag_try_sys1_failed 8
+ fw_setenv flag_try_sys2_failed 8
+
+ # Kernel and rootfs are placed in 2 different UBI
+ CI_KERN_UBIPART="ubi_kernel"
+ CI_ROOT_UBIPART="rootfs"
+ nand_do_upgrade "$1"
+ ;;
+ *)
+ default_do_upgrade "$1"
+ ;;
+ esac
+}
diff --git a/target/linux/ipq807x/files/arch/arm64/boot/dts/qcom/ipq8071-ax3600.dts b/target/linux/ipq807x/files/arch/arm64/boot/dts/qcom/ipq8071-ax3600.dts
new file mode 100644
index 0000000000..f3e82e2251
--- /dev/null
+++ b/target/linux/ipq807x/files/arch/arm64/boot/dts/qcom/ipq8071-ax3600.dts
@@ -0,0 +1,73 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2021, Robert Marko <robimarko at gmail.com> */
+
+/dts-v1/;
+
+#include "ipq8071-ax3600.dtsi"
+
+/ {
+ model = "Xiaomi AX3600";
+ compatible = "xiaomi,ax3600", "qcom,ipq8074";
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_system_blue: system-blue {
+ label = "blue:system";
+ gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_system_yellow: system-yellow {
+ label = "yellow:system";
+ gpios = <&tlmm 43 GPIO_ACTIVE_HIGH>;
+ };
+
+ network-yellow {
+ label = "yellow:network";
+ gpios = <&tlmm 22 GPIO_ACTIVE_HIGH>;
+ };
+
+ network-blue {
+ label = "blue:network";
+ gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
+ };
+
+ aiot {
+ label = "blue:aiot";
+ gpios = <&tlmm 51 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tpt";
+ };
+ };
+};
+
+&pcie_qmp0 {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+
+ perst-gpio = <&tlmm 52 GPIO_ACTIVE_HIGH>;
+
+ bridge at 0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi0: wifi at 1,0 {
+ status = "okay";
+
+ compatible = "qcom,ath10k";
+ reg = <0x00010000 0 0 0 0>;
+
+ qcom,ath10k-calibration-variant = "Xiaomi-AX3600";
+ nvmem-cell-names = "calibration";
+ nvmem-cells = <&caldata_qca9889>;
+ };
+ };
+};
+
+&wifi {
+ qcom,ath11k-calibration-variant = "Xiaomi-AX3600";
+};
diff --git a/target/linux/ipq807x/files/arch/arm64/boot/dts/qcom/ipq8071-ax3600.dtsi b/target/linux/ipq807x/files/arch/arm64/boot/dts/qcom/ipq8071-ax3600.dtsi
new file mode 100644
index 0000000000..c18cef52f3
--- /dev/null
+++ b/target/linux/ipq807x/files/arch/arm64/boot/dts/qcom/ipq8071-ax3600.dtsi
@@ -0,0 +1,311 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2021, Robert Marko <robimarko at gmail.com> */
+
+#include "ipq8074-512m.dtsi"
+#include "ipq8074-ac-cpu.dtsi"
+#include "ipq8074-ess.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ aliases {
+ serial0 = &blsp1_uart5;
+ led-boot = &led_system_yellow;
+ led-failsafe = &led_system_yellow;
+ led-running = &led_system_blue;
+ led-upgrade = &led_system_yellow;
+ label-mac-device = &dp2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs-append = " root=/dev/ubiblock0_0";
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+};
+
+&tlmm {
+ mdio_pins: mdio-pins {
+ mdc {
+ pins = "gpio68";
+ function = "mdc";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ mdio {
+ pins = "gpio69";
+ function = "mdio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+};
+
+&blsp1_uart5 {
+ status = "okay";
+};
+
+&prng {
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&crypto {
+ status = "okay";
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&qpic_nand {
+ status = "okay";
+
+ /*
+ * Bootloader will find the NAND DT node by the compatible and
+ * then "fixup" it by adding the partitions from the SMEM table
+ * using the legacy bindings thus making it impossible for us
+ * to change the partition table or utilize NVMEM for calibration.
+ * So add a dummy partitions node that bootloader will populate
+ * and set it as disabled so the kernel ignores it instead of
+ * printing warnings due to the broken way bootloader adds the
+ * partitions.
+ */
+ partitions {
+ status = "disabled";
+ };
+
+ nand at 0 {
+ reg = <0>;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ nand-bus-width = <8>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "0:sbl1";
+ reg = <0x0 0x100000>;
+ read-only;
+ };
+
+ partition at 100000 {
+ label = "0:mibib";
+ reg = <0x100000 0x100000>;
+ read-only;
+ };
+
+ partition at 200000 {
+ label = "0:qsee";
+ reg = <0x200000 0x300000>;
+ read-only;
+ };
+
+ partition at 500000 {
+ label = "0:devcfg";
+ reg = <0x500000 0x80000>;
+ read-only;
+ };
+
+ partition at 580000 {
+ label = "0:rpm";
+ reg = <0x580000 0x80000>;
+ read-only;
+ };
+
+ partition at 600000 {
+ label = "0:cdt";
+ reg = <0x600000 0x80000>;
+ read-only;
+ };
+
+ partition at 680000 {
+ label = "0:appsblenv";
+ reg = <0x680000 0x80000>;
+ };
+
+ partition at 700000 {
+ label = "0:appsbl";
+ reg = <0x700000 0x100000>;
+ read-only;
+ };
+
+ partition at 800000 {
+ label = "0:art";
+ reg = <0x800000 0x80000>;
+ read-only;
+
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_dp2: macaddr at 6 {
+ reg = <0x6 0x6>;
+ };
+
+ macaddr_dp3: macaddr at c {
+ reg = <0xc 0x6>;
+ };
+
+ macaddr_dp4: macaddr at 12 {
+ reg = <0x12 0x6>;
+ };
+
+ macaddr_dp5: macaddr at 18 {
+ reg = <0x18 0x6>;
+ };
+
+ caldata_qca9889: caldata at 4d000 {
+ reg = <0x33000 0x844>;
+ };
+ };
+
+ partition at 880000 {
+ label = "bdata";
+ reg = <0x880000 0x80000>;
+ };
+
+ partition at 900000 {
+ /* This is crash + crash_syslog parts combined */
+ label = "pstore";
+ reg = <0x900000 0x100000>;
+ };
+
+ /* Make the first rootfs a dedicated ubi partition for kernel */
+ partition at a00000 {
+ label = "ubi_kernel";
+ reg = <0xa00000 0x23c0000>;
+ };
+
+ /* Place the real rootfs in the original second rootfs and
+ * expand it to the end of the nand
+ */
+ rootfs: partition at 2dc0000 {
+ label = "rootfs";
+ reg = <0x2dc0000 0xd240000>;
+ };
+ };
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>;
+
+ qca8075_1: ethernet-phy at 1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+
+ qca8075_2: ethernet-phy at 2 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <2>;
+ };
+
+ qca8075_3: ethernet-phy at 3 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <3>;
+ };
+
+ qca8075_4: ethernet-phy at 4 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <4>;
+ };
+};
+
+&switch {
+ status = "okay";
+
+ switch_cpu_bmp = <0x1>; /* cpu port bitmap */
+ switch_lan_bmp = <0x1e>; /* lan port bitmap */
+ switch_wan_bmp = <0x20>; /* wan port bitmap */
+ switch_mac_mode = <0x0>; /* mac mode for uniphy instance0*/
+ switch_mac_mode1 = <0xff>; /* mac mode for uniphy instance1*/
+ switch_mac_mode2 = <0xff>; /* mac mode for uniphy instance2*/
+ bm_tick_mode = <0>; /* bm tick mode */
+ tm_tick_mode = <0>; /* tm tick mode */
+
+ qcom,port_phyinfo {
+ port at 0 {
+ port_id = <1>;
+ phy_address = <0>;
+ };
+ port at 1 {
+ port_id = <2>;
+ phy_address = <1>;
+ };
+ port at 2 {
+ port_id = <3>;
+ phy_address = <2>;
+ };
+ port at 3 {
+ port_id = <4>;
+ phy_address = <3>;
+ };
+ port at 4 {
+ port_id = <5>;
+ phy_address = <4>;
+ };
+ };
+};
+
+&edma {
+ status = "okay";
+};
+
+&dp2 {
+ status = "okay";
+ phy-handle = <&qca8075_1>;
+ label = "wan";
+ nvmem-cells = <&macaddr_dp2>;
+ nvmem-cell-names = "mac-address";
+};
+
+&dp3 {
+ status = "okay";
+ phy-handle = <&qca8075_2>;
+ label = "lan1";
+ nvmem-cells = <&macaddr_dp3>;
+ nvmem-cell-names = "mac-address";
+};
+
+&dp4 {
+ status = "okay";
+ phy-handle = <&qca8075_3>;
+ label = "lan2";
+ nvmem-cells = <&macaddr_dp4>;
+ nvmem-cell-names = "mac-address";
+};
+
+&dp5 {
+ status = "okay";
+ phy-handle = <&qca8075_4>;
+ label = "lan3";
+ nvmem-cells = <&macaddr_dp5>;
+ nvmem-cell-names = "mac-address";
+};
+
+&wifi {
+ status = "okay";
+
+ qcom,ath11k-fw-memory-mode = <1>;
+};
diff --git a/target/linux/ipq807x/image/generic.mk b/target/linux/ipq807x/image/generic.mk
index 91a3daeedf..11cca54506 100644
--- a/target/linux/ipq807x/image/generic.mk
+++ b/target/linux/ipq807x/image/generic.mk
@@ -16,3 +16,21 @@ define Device/UbiFit
IMAGE/factory.ubi := append-ubi
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
endef
+
+define Device/xiaomi_ax3600
+ $(call Device/FitImage)
+ $(call Device/UbiFit)
+ DEVICE_VENDOR := Xiaomi
+ DEVICE_MODEL := AX3600
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ DEVICE_DTS_CONFIG := config at ac04
+ SOC := ipq8071
+ KERNEL_SIZE := 36608k
+ DEVICE_PACKAGES := ipq-wifi-xiaomi_ax3600 kmod-ath10k-ct-smallbuffers ath10k-firmware-qca9887-ct
+ifneq ($(CONFIG_TARGET_ROOTFS_INITRAMFS),)
+ ARTIFACTS := initramfs-factory.ubi
+ ARTIFACT/initramfs-factory.ubi := append-image-stage initramfs-uImage.itb | ubinize-kernel
+endif
+endef
+TARGET_DEVICES += xiaomi_ax3600
More information about the lede-commits
mailing list