[openwrt/openwrt] filogic: add support for ASUS TUF AX6000

LEDE Commits lede-commits at lists.infradead.org
Thu Dec 7 23:02:45 PST 2023 

rmilecki pushed a commit to openwrt/openwrt.git, branch openwrt-23.05:
https://git.openwrt.org/557a32aba0aaaae860a0abae181c42df2cf39188

commit 557a32aba0aaaae860a0abae181c42df2cf39188
Author: Patryk Kowalczyk <patryk at kowalczyk.ws>
AuthorDate: Sat Sep 16 03:02:35 2023 +0200

    filogic: add support for ASUS TUF AX6000
    
    Hardware
    ========
    SOC: MediaTek MT7986
    RAM: 512MB DDR3
    FLASH: 256MB SPI-NAND
    WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz 4T4R
    ETH: MediaTek MT7530 Switch (LAN)
    MaxLinear GPY211C 2.5 N-Base-T PHY (WAN)
    MaxLinear GPY211C 2.5 N-Base-T PHY (LAN)
    UART: 3V3 115200 8N1 (Do not connect VCC)
    USB 3.1
    
    Installation
    ============
    
    Download the OpenWrt initramfs image. Copy the image to a TFTP server
    reachable at 192.168.1.70/24. Rename the image to TUF-AX6000.bin.
    
    Connect to the serial console, interrupt the auto boot process by
    pressing '4' when prompted or press '1' and set client IP, server
    IP and name of the image.
    
    yOU don't need to open the case or even soldering anything.
    use three goldpin wires, remove their plastic cover and connect
    them to the console pinout via the case holes.
    
    You can see three holes
    From Bottom: RX, TX, Ground - partially covered
    
    Download & Boot the OpenWrt initramfs image.
    
    In case of option '4'
    $ setenv ipaddr 192.168.1.1
    $ setenv serverip 192.168.1.70
    $ tftpboot 0x46000000 TUF-AX6000.bin
    $ bootm 0x46000000
    
    In case of option '1'
    1: Load System code to SDRAM via TFTP.
    Please Input new ones /or Ctrl-C to discard
    Input device IP (192.168.1.1) ==:
    Input server IP (192.168.1.70) ==:
    Input Linux Kernel filename (TUF-AX6000.trx) ==:
    
    Wait for OpenWrt to boot. Transfer the sysupgrade
    image to the device using scp and install using sysupgrade.
    
    $ sysupgrade -n <path-to-sysupgrade.bin>
    
    Missing features
    ================
    
    2.5Gb LAN port LED is ON during boot or when the LAN cable is disconnected
    
    The cover yellow light is not supported. (only blue one)
    
    Signed-off-by: Patryk Kowalczyk <patryk at kowalczyk.ws>
    (cherry picked from commit d522ccecb28f941aadcaf7a50cd6daa861f468a7)
---
 .../linux/mediatek/dts/mt7986a-asus-tuf-ax6000.dts | 382 +++++++++++++++++++++
 .../filogic/base-files/etc/board.d/02_network      |   6 +-
 .../etc/hotplug.d/firmware/11-mt76-caldata         |   3 +-
 .../etc/hotplug.d/ieee80211/11_fix_wifi_mac        |   3 +-
 .../base-files/lib/preinit/10_fix_eth_mac.sh       |   3 +-
 .../filogic/base-files/lib/upgrade/platform.sh     |   3 +-
 target/linux/mediatek/image/filogic.mk             |  16 +
 7 files changed, 411 insertions(+), 5 deletions(-)

diff --git a/target/linux/mediatek/dts/mt7986a-asus-tuf-ax6000.dts b/target/linux/mediatek/dts/mt7986a-asus-tuf-ax6000.dts
new file mode 100644
index 0000000000..2e9114f99c
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7986a-asus-tuf-ax6000.dts
@@ -0,0 +1,382 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+#include "mt7986a.dtsi"
+
+/ {
+	model = "ASUS TUF-AX6000";
+	compatible = "asus,tuf-ax6000", "mediatek,mt7986a";
+
+	aliases {
+		serial0 = &uart0;
+		led-boot = &led_system;
+		led-failsafe = &led_system;
+		led-running = &led_system;
+		led-upgrade = &led_system;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+		bootargs-override = "ubi.mtd=UBI_DEV";
+	};
+
+	memory {
+		reg = <0 0x40000000 0 0x20000000>;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+
+		mesh {
+			label = "wps";
+			gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		wlan {
+			label = "white:wlan";
+			gpios = <&pio 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy1tpt";
+		};
+
+		led_system: system {
+			label = "white:system";
+			gpios = <&pio 11 GPIO_ACTIVE_HIGH>;
+		};
+
+		wan-red {
+			label = "red:wan";
+			gpios = <&pio 12 GPIO_ACTIVE_LOW>;
+		};
+
+		cover-blue {
+			label = "blue:cover";
+			gpios = <&pio 20 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+};
+
+&crypto {
+	status = "okay";
+};
+
+&eth {
+	status = "okay";
+
+	gmac0: mac at 0 {
+		/* LAN */
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "2500base-x";
+
+		fixed-link {
+			speed = <2500>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	gmac1: mac at 1 {
+		/* WAN */
+		compatible = "mediatek,eth-mac";
+		reg = <1>;
+		phy-mode = "2500base-x";
+		phy-handle = <&phy6>;
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
+
+&mdio {
+	reset-gpios = <&pio 6 GPIO_ACTIVE_LOW>;
+	reset-delay-us = <50000>;
+	reset-post-delay-us = <20000>;
+
+	phy5: phy at 5 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <5>;
+
+		mxl,led-config = <0x03f0 0x0 0x0 0x0>;
+	};
+
+	phy6: phy at 6 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <6>;
+
+		/* LED0: CONN (WAN white) */
+		mxl,led-config = <0x03f0 0x0 0x0 0x0>;
+	};
+
+	switch: switch at 0 {
+		compatible = "mediatek,mt7531";
+		reg = <31>;
+
+		reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
+		reset-assert-us = <10000>;
+		reset-deassert-us = <10000>;
+	};
+};
+
+&pio {
+	spi_flash_pins: spi-flash-pins-33-to-38 {
+		mux {
+			function = "spi";
+			groups = "spi0", "spi0_wp_hold";
+		};
+		conf-pu {
+			pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
+			drive-strength = <8>;
+			mediatek,pull-up-adv = <0>; /* bias-disable */
+		};
+		conf-pd {
+			pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
+			drive-strength = <8>;
+			mediatek,pull-down-adv = <0>; /* bias-disable */
+		};
+	};
+
+	wf_2g_5g_pins: wf_2g_5g-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_2g", "wf_5g";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+			       "WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+
+	wf_dbdc_pins: wf-dbdc-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_dbdc";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+				"WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+				"WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+				"WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+				"WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+				"WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+				"WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+};
+
+&pcie_phy {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_flash_pins>;
+	status = "okay";
+
+	spi_nand_flash: flash at 0 {
+		compatible = "spi-nand";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0>;
+
+		spi-max-frequency = <20000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+
+		partitions: partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition at 0 {
+				label = "bootloader";
+				reg = <0x0 0x400000>;
+				read-only;
+			};
+
+			partition at 400000 {
+				label = "UBI_DEV";
+				reg = <0x400000 0xfc00000>;
+			};
+		};
+	};
+};
+
+&switch {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port at 1 {
+			reg = <4>;
+			label = "lan1";
+		};
+
+		port at 2 {
+			reg = <3>;
+			label = "lan2";
+		};
+
+		port at 3 {
+			reg = <2>;
+			label = "lan3";
+		};
+
+		port at 4 {
+			reg = <1>;
+			label = "lan4";
+		};
+
+		port at 5 {
+			reg = <5>;
+			label = "lan5";
+			phy-mode = "2500base-x";
+			phy-handle = <&phy5>;
+
+		};
+
+		port at 6 {
+			reg = <6>;
+			label = "cpu";
+			ethernet = <&gmac0>;
+			phy-mode = "2500base-x";
+
+			fixed-link {
+				speed = <2500>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy at 1 {
+			reg = <1>;
+
+			mediatek,led-config = <
+				0x21 0x8009 /* BASIC_CTRL */
+				0x22 0x0c00 /* ON_DURATION */
+				0x23 0x1400 /* BLINK_DURATION */
+				0x24 0x8000 /* LED0_ON_CTRL */
+				0x25 0x0000 /* LED0_BLINK_CTRL */
+				0x26 0xc007 /* LED1_ON_CTRL */
+				0x27 0x003f /* LED1_BLINK_CTRL */
+			>;
+		};
+
+		phy at 2 {
+			reg = <2>;
+
+			mediatek,led-config = <
+				0x21 0x8009 /* BASIC_CTRL */
+				0x22 0x0c00 /* ON_DURATION */
+				0x23 0x1400 /* BLINK_DURATION */
+				0x24 0x8000 /* LED0_ON_CTRL */
+				0x25 0x0000 /* LED0_BLINK_CTRL */
+				0x26 0xc007 /* LED1_ON_CTRL */
+				0x27 0x003f /* LED1_BLINK_CTRL */
+			>;
+		};
+
+		phy at 3 {
+			reg = <3>;
+
+			mediatek,led-config = <
+				0x21 0x8009 /* BASIC_CTRL */
+				0x22 0x0c00 /* ON_DURATION */
+				0x23 0x1400 /* BLINK_DURATION */
+				0x24 0x8000 /* LED0_ON_CTRL */
+				0x25 0x0000 /* LED0_BLINK_CTRL */
+				0x26 0xc007 /* LED1_ON_CTRL */
+				0x27 0x003f /* LED1_BLINK_CTRL */
+			>;
+		};
+
+		phy at 4 {
+			reg = <4>;
+
+			mediatek,led-config = <
+				0x21 0x8009 /* BASIC_CTRL */
+				0x22 0x0c00 /* ON_DURATION */
+				0x23 0x1400 /* BLINK_DURATION */
+				0x24 0x8000 /* LED0_ON_CTRL */
+				0x25 0x0000 /* LED0_BLINK_CTRL */
+				0x26 0xc007 /* LED1_ON_CTRL */
+				0x27 0x003f /* LED1_BLINK_CTRL */
+			>;
+		};
+	};
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&wifi {
+	status = "okay";
+	pinctrl-names = "default", "dbdc";
+	pinctrl-0 = <&wf_2g_5g_pins>;
+	pinctrl-1 = <&wf_dbdc_pins>;
+};
+
+&trng {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&ssusb {
+	vusb33-supply = <&reg_3p3v>;
+	vbus-supply = <&reg_5v>;
+	status = "okay";
+};
+
+&usb_phy {
+	status = "okay";
+};
\ No newline at end of file
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
index d9fa477353..aad1d67ff6 100644
--- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
+++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
@@ -15,6 +15,9 @@ mediatek_setup_interfaces()
 	mediatek,mt7981-rfb)
 		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" eth1
 		;;
+	asus,tuf-ax6000)
+		ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5" eth1
+		;;
 	netgear,wax220|\
 	ubnt,unifi-6-plus|\
 	zyxel,nwa50ax-pro)
@@ -78,7 +81,8 @@ mediatek_setup_macs()
 	local label_mac=""
 
 	case $board in
-	asus,tuf-ax4200)
+	asus,tuf-ax4200|\
+	asus,tuf-ax6000)
 		CI_UBIPART="UBI_DEV"
 		addr=$(mtd_get_mac_binary_ubi "Factory" 0x4)
 		wan_mac="${addr}"
diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata
index e782637348..63c1ec31b7 100644
--- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata
+++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/firmware/11-mt76-caldata
@@ -45,7 +45,8 @@ case "$FIRMWARE" in
 	;;
 "mediatek/mt7986_eeprom_mt7976_dbdc.bin")
 	case "$board" in
-	asus,tuf-ax4200)
+	asus,tuf-ax4200|\
+	asus,tuf-ax6000)
 		CI_UBIPART="UBI_DEV"
 		caldata_extract_ubi "Factory" 0x0 0x1000
 		;;
diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
index 5de4061c94..395cc0f2dc 100644
--- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
+++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
@@ -16,7 +16,8 @@ case "$board" in
 		[ "$PHYNBR" = "1" ] && cat $key_path/6gMAC > /sys${DEVPATH}/macaddress
 		[ "$PHYNBR" = "2" ] && cat $key_path/5gMAC > /sys${DEVPATH}/macaddress
 		;;
-	asus,tuf-ax4200)
+	asus,tuf-ax4200|\
+	asus,tuf-ax6000)
 		CI_UBIPART="UBI_DEV"
 		addr=$(mtd_get_mac_binary_ubi "Factory" 0x4)
 		# Originally, phy0 is phy1 mac with LA bit set. However, this would conflict
diff --git a/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh b/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh
index 69d0ab6c60..d770b13643 100644
--- a/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh
+++ b/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh
@@ -10,7 +10,8 @@ preinit_set_mac_address() {
 		ip link set dev game address "$(cat $key_path/LANMAC)"
 		ip link set dev eth1 address "$(cat $key_path/WANMAC)"
 		;;
-	asus,tuf-ax4200)
+	asus,tuf-ax4200|\
+	asus,tuf-ax6000)
 		CI_UBIPART="UBI_DEV"
 		addr=$(mtd_get_mac_binary_ubi "Factory" 0x4)
 		ip link set dev eth0 address "$addr"
diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
index c2a9c8f3b0..1d8b6afb84 100755
--- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
+++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
@@ -56,7 +56,8 @@ platform_do_upgrade() {
 		CI_ROOTPART="rootfs"
 		emmc_do_upgrade "$1"
 		;;
-	asus,tuf-ax4200)
+	asus,tuf-ax4200|\
+	asus,tuf-ax6000)
 		CI_UBIPART="UBI_DEV"
 		CI_KERNPART="linux"
 		nand_do_upgrade "$1"
diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk
index 932bf616c3..f616f7a72d 100644
--- a/target/linux/mediatek/image/filogic.mk
+++ b/target/linux/mediatek/image/filogic.mk
@@ -121,6 +121,22 @@ define Device/asus_tuf-ax4200
 endef
 TARGET_DEVICES += asus_tuf-ax4200
 
+define Device/asus_tuf-ax6000
+  DEVICE_VENDOR := ASUS
+  DEVICE_MODEL := TUF-AX6000
+  DEVICE_DTS := mt7986a-asus-tuf-ax6000
+  DEVICE_DTS_DIR := ../dts
+  DEVICE_DTS_LOADADDR := 0x47000000
+  DEVICE_PACKAGES := kmod-usb3 kmod-mt7986-firmware mt7986-wo-firmware
+  IMAGES := sysupgrade.bin
+  KERNEL := kernel-bin | lzma | \
+	fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
+  KERNEL_INITRAMFS := kernel-bin | lzma | \
+	fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
+  IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+endef
+TARGET_DEVICES += asus_tuf-ax6000
+
 define Device/acer_predator-w6
   DEVICE_VENDOR := Acer
   DEVICE_MODEL := Predator W6

More information about the lede-commits mailing list