[openwrt/openwrt] uboot-mediatek: add support for Xiaomi WR30U
LEDE Commits
lede-commits at lists.infradead.org
Mon Aug 7 15:54:25 PDT 2023
dangole pushed a commit to openwrt/openwrt.git, branch openwrt-23.05:
https://git.openwrt.org/d0fc9e96be5a26869ee0d273894889e21651865c
commit d0fc9e96be5a26869ee0d273894889e21651865c
Author: Hank Moretti <mchank9999 at gmail.com>
AuthorDate: Thu Jul 20 17:42:58 2023 +0000
uboot-mediatek: add support for Xiaomi WR30U
Add a custom uboot build to support openwrt uboot layout.
Signed-off-by: Hank Moretti <mchank9999 at gmail.com>
---
package/boot/uboot-envtools/files/mediatek_filogic | 2 +
package/boot/uboot-mediatek/Makefile | 13 +
.../patches/434-add-xiaomi_mi-router-wr30u.patch | 456 +++++++++++++++++++++
3 files changed, 471 insertions(+)
diff --git a/package/boot/uboot-envtools/files/mediatek_filogic b/package/boot/uboot-envtools/files/mediatek_filogic
index 77c9d964db..81b1283690 100644
--- a/package/boot/uboot-envtools/files/mediatek_filogic
+++ b/package/boot/uboot-envtools/files/mediatek_filogic
@@ -47,6 +47,7 @@ mercusys,mr90x-v1)
netgear,wax220)
ubootenv_add_uci_config "/dev/mtd5" "0x0" "0x20000" "0x20000"
;;
+xiaomi,mi-router-wr30u-stock|\
xiaomi,redmi-router-ax6000-stock)
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x10000" "0x20000"
ubootenv_add_uci_sys_config "/dev/mtd2" "0x0" "0x10000" "0x20000"
@@ -56,6 +57,7 @@ qihoo,360t7|\
tplink,tl-xdr4288|\
tplink,tl-xdr6086|\
tplink,tl-xdr6088|\
+xiaomi,mi-router-wr30u-ubootmod|\
xiaomi,redmi-router-ax6000-ubootmod)
. /lib/upgrade/nand.sh
local envubi=$(nand_find_ubi ubi)
diff --git a/package/boot/uboot-mediatek/Makefile b/package/boot/uboot-mediatek/Makefile
index 33fd7e086e..55965e64db 100644
--- a/package/boot/uboot-mediatek/Makefile
+++ b/package/boot/uboot-mediatek/Makefile
@@ -200,6 +200,18 @@ define U-Boot/mt7981_qihoo_360t7
DEPENDS:=+trusted-firmware-a-mt7981-spim-nand-ddr3
endef
+define U-Boot/mt7981_xiaomi_mi-router-wr30u
+ NAME:=Xiaomi Router WR30U
+ BUILD_SUBTARGET:=filogic
+ BUILD_DEVICES:=xiaomi_mi-router-wr30u-ubootmod
+ UBOOT_CONFIG:=mt7981_xiaomi_mi-router-wr30u
+ UBOOT_IMAGE:=u-boot.fip
+ BL2_BOOTDEV:=spim-nand
+ BL2_SOC:=mt7981
+ BL2_DDRTYPE:=ddr3
+ DEPENDS:=+trusted-firmware-a-mt7981-spim-nand-ddr3
+endef
+
define U-Boot/mt7986_rfb
NAME:=MT7986 Reference Board
BUILD_SUBTARGET:=filogic
@@ -327,6 +339,7 @@ UBOOT_TARGETS := \
mt7629_rfb \
mt7981_h3c_magic-nx30-pro \
mt7981_qihoo_360t7 \
+ mt7981_xiaomi_mi-router-wr30u \
mt7986_bananapi_bpi-r3-emmc \
mt7986_bananapi_bpi-r3-sdmmc \
mt7986_bananapi_bpi-r3-snand \
diff --git a/package/boot/uboot-mediatek/patches/434-add-xiaomi_mi-router-wr30u.patch b/package/boot/uboot-mediatek/patches/434-add-xiaomi_mi-router-wr30u.patch
new file mode 100644
index 0000000000..6be64e5421
--- /dev/null
+++ b/package/boot/uboot-mediatek/patches/434-add-xiaomi_mi-router-wr30u.patch
@@ -0,0 +1,456 @@
+--- /dev/null
++++ b/configs/mt7981_xiaomi_mi-router-wr30u_defconfig
+@@ -0,0 +1,175 @@
++CONFIG_ARM=y
++CONFIG_POSITION_INDEPENDENT=y
++CONFIG_ARCH_MEDIATEK=y
++CONFIG_TARGET_MT7981=y
++CONFIG_TEXT_BASE=0x41e00000
++CONFIG_SYS_MALLOC_F_LEN=0x4000
++CONFIG_SYS_HAS_NONCACHED_MEMORY=y
++CONFIG_NR_DRAM_BANKS=1
++CONFIG_DEFAULT_DEVICE_TREE="mt7981_xiaomi_mi-router-wr30u"
++CONFIG_DEFAULT_ENV_FILE="xiaomi_mi-router-wr30u_env"
++CONFIG_DEFAULT_FDT_FILE="mediatek/mt7981_xiaomi_mi-router-wr30u.dtb"
++CONFIG_OF_LIBFDT_OVERLAY=y
++CONFIG_DEBUG_UART_BASE=0x11002000
++CONFIG_DEBUG_UART_CLOCK=40000000
++CONFIG_DEBUG_UART=y
++CONFIG_SYS_LOAD_ADDR=0x46000000
++CONFIG_SMBIOS_PRODUCT_NAME=""
++CONFIG_AUTOBOOT_KEYED=y
++CONFIG_BOOTDELAY=30
++CONFIG_AUTOBOOT_MENU_SHOW=y
++CONFIG_CFB_CONSOLE_ANSI=y
++CONFIG_BOARD_LATE_INIT=y
++CONFIG_BUTTON=y
++CONFIG_BUTTON_GPIO=y
++CONFIG_GPIO_HOG=y
++CONFIG_CMD_ENV_FLAGS=y
++CONFIG_FIT=y
++CONFIG_FIT_ENABLE_SHA256_SUPPORT=y
++CONFIG_LED=y
++CONFIG_LED_BLINK=y
++CONFIG_LED_GPIO=y
++CONFIG_LOGLEVEL=7
++CONFIG_LOG=y
++CONFIG_SYS_PROMPT="MT7981> "
++CONFIG_CMD_BOOTMENU=y
++CONFIG_CMD_BOOTP=y
++CONFIG_CMD_BUTTON=y
++CONFIG_CMD_CACHE=y
++CONFIG_CMD_CDP=y
++CONFIG_CMD_CPU=y
++CONFIG_CMD_DHCP=y
++CONFIG_CMD_DM=y
++CONFIG_CMD_DNS=y
++CONFIG_CMD_ECHO=y
++CONFIG_CMD_ENV_READMEM=y
++CONFIG_CMD_ERASEENV=y
++CONFIG_CMD_EXT4=y
++CONFIG_CMD_FAT=y
++CONFIG_CMD_FDT=y
++CONFIG_CMD_FS_GENERIC=y
++CONFIG_CMD_FS_UUID=y
++CONFIG_CMD_GPIO=y
++CONFIG_CMD_GPT=y
++CONFIG_CMD_HASH=y
++CONFIG_CMD_ITEST=y
++CONFIG_CMD_LED=y
++CONFIG_CMD_LICENSE=y
++CONFIG_CMD_LINK_LOCAL=y
++# CONFIG_CMD_MBR is not set
++CONFIG_CMD_PCI=y
++CONFIG_CMD_PSTORE=y
++CONFIG_CMD_PSTORE_MEM_ADDR=0x42ff0000
++CONFIG_CMD_SF_TEST=y
++CONFIG_CMD_PING=y
++CONFIG_CMD_PXE=y
++CONFIG_CMD_PWM=y
++CONFIG_CMD_SMC=y
++CONFIG_CMD_TFTPBOOT=y
++CONFIG_CMD_TFTPSRV=y
++CONFIG_CMD_UBI=y
++CONFIG_CMD_UBI_RENAME=y
++CONFIG_CMD_UBIFS=y
++CONFIG_CMD_ASKENV=y
++CONFIG_CMD_PART=y
++CONFIG_CMD_RARP=y
++CONFIG_CMD_SETEXPR=y
++CONFIG_CMD_SLEEP=y
++CONFIG_CMD_SNTP=y
++CONFIG_CMD_SOURCE=y
++CONFIG_CMD_STRINGS=y
++CONFIG_CMD_UUID=y
++CONFIG_DISPLAY_CPUINFO=y
++CONFIG_DM_MTD=y
++CONFIG_DM_REGULATOR=y
++CONFIG_DM_REGULATOR_FIXED=y
++CONFIG_DM_REGULATOR_GPIO=y
++CONFIG_DM_PWM=y
++CONFIG_PWM_MTK=y
++CONFIG_HUSH_PARSER=y
++CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
++CONFIG_SYS_RELOC_GD_ENV_ADDR=y
++CONFIG_VERSION_VARIABLE=y
++CONFIG_PARTITION_UUIDS=y
++CONFIG_NETCONSOLE=y
++CONFIG_REGMAP=y
++CONFIG_SYSCON=y
++CONFIG_CLK=y
++CONFIG_DM_GPIO=y
++CONFIG_DM_SCSI=y
++CONFIG_AHCI=y
++CONFIG_AHCI_PCI=y
++CONFIG_SCSI_AHCI=y
++CONFIG_SCSI=y
++CONFIG_CMD_SCSI=y
++CONFIG_PHY=y
++CONFIG_PHY_MTK_TPHY=y
++CONFIG_PHY_FIXED=y
++CONFIG_MTK_AHCI=y
++CONFIG_DM_ETH=y
++CONFIG_MEDIATEK_ETH=y
++CONFIG_PCI=y
++# CONFIG_MMC is not set
++# CONFIG_DM_MMC is not set
++CONFIG_MTD=y
++CONFIG_MTD_UBI_FASTMAP=y
++CONFIG_DM_PCI=y
++CONFIG_PCIE_MEDIATEK=y
++CONFIG_PINCTRL=y
++CONFIG_PINCONF=y
++CONFIG_PINCTRL_MT7622=y
++CONFIG_POWER_DOMAIN=y
++CONFIG_PRE_CONSOLE_BUFFER=y
++CONFIG_PRE_CON_BUF_ADDR=0x4007EF00
++CONFIG_MTK_POWER_DOMAIN=y
++CONFIG_RAM=y
++CONFIG_DM_SERIAL=y
++CONFIG_MTK_SERIAL=y
++CONFIG_SPI=y
++CONFIG_DM_SPI=y
++CONFIG_MTK_SPI_NAND=y
++CONFIG_MTK_SPI_NAND_MTD=y
++CONFIG_SYSRESET_WATCHDOG=y
++CONFIG_WDT_MTK=y
++CONFIG_LZO=y
++CONFIG_ZSTD=y
++CONFIG_HEXDUMP=y
++CONFIG_RANDOM_UUID=y
++CONFIG_REGEX=y
++CONFIG_OF_EMBED=y
++CONFIG_ENV_OVERWRITE=y
++CONFIG_ENV_IS_IN_UBI=y
++CONFIG_ENV_UBI_PART="ubi"
++CONFIG_ENV_SIZE=0x1f000
++CONFIG_ENV_SIZE_REDUND=0x1f000
++CONFIG_ENV_UBI_VOLUME="ubootenv"
++CONFIG_ENV_UBI_VOLUME_REDUND="ubootenv2"
++CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
++CONFIG_NET_RANDOM_ETHADDR=y
++CONFIG_REGMAP=y
++CONFIG_SYSCON=y
++CONFIG_CLK=y
++CONFIG_PHY_FIXED=y
++CONFIG_DM_ETH=y
++CONFIG_MEDIATEK_ETH=y
++CONFIG_PINCTRL=y
++CONFIG_PINCONF=y
++CONFIG_PINCTRL_MT7981=y
++CONFIG_POWER_DOMAIN=y
++CONFIG_MTK_POWER_DOMAIN=y
++CONFIG_DM_REGULATOR=y
++CONFIG_DM_REGULATOR_FIXED=y
++CONFIG_DM_SERIAL=y
++CONFIG_MTK_SERIAL=y
++CONFIG_HEXDUMP=y
++CONFIG_USE_DEFAULT_ENV_FILE=y
++CONFIG_MTD_SPI_NAND=y
++CONFIG_MTK_SPIM=y
++CONFIG_CMD_MTD=y
++CONFIG_CMD_NAND=y
++CONFIG_CMD_NAND_TRIMFFS=y
++CONFIG_LMB_MAX_REGIONS=64
++CONFIG_USE_IPADDR=y
++CONFIG_IPADDR="192.168.1.1"
++CONFIG_USE_SERVERIP=y
++CONFIG_SERVERIP="192.168.1.254"
+--- /dev/null
++++ b/arch/arm/dts/mt7981_xiaomi_mi-router-wr30u.dts
+@@ -0,0 +1,216 @@
++// SPDX-License-Identifier: GPL-2.0
++/*
++ * Copyright (c) 2022 MediaTek Inc.
++ * Author: Sam Shih <sam.shih at mediatek.com>
++ */
++
++/dts-v1/;
++#include "mt7981.dtsi"
++#include <dt-bindings/gpio/gpio.h>
++#include <dt-bindings/input/linux-event-codes.h>
++
++/ {
++ #address-cells = <1>;
++ #size-cells = <1>;
++ model = "Xiaomi Router WR30U";
++ compatible = "mediatek,mt7981", "mediatek,mt7981-rfb";
++
++ chosen {
++ stdout-path = &uart0;
++ tick-timer = &timer0;
++ };
++
++ config {
++ blink_led = "yellow:network";
++ system_led = "yellow:system";
++ };
++
++ gpio-keys {
++ compatible = "gpio-keys";
++
++ reset {
++ label = "reset";
++ gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
++ linux,code = <KEY_RESTART>;
++ };
++
++ mesh {
++ label = "mesh";
++ gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
++ linux,code = <BTN_9>;
++ linux,input-type = <EV_SW>;
++ };
++ };
++
++ leds {
++ compatible = "gpio-leds";
++
++ led_system_blue {
++ label = "blue:system";
++ gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
++ };
++
++ led_system_yellow {
++ label = "yellow:system";
++ gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
++ };
++
++ led_network_blue {
++ label = "blue:network";
++ gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
++ };
++
++ led_network_yellow {
++ label = "yellow:network";
++ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
++ };
++ };
++};
++
++&uart0 {
++ mediatek,force-highspeed;
++ status = "okay";
++};
++
++&uart1 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&uart1_pins>;
++ status = "disabled";
++};
++
++ð {
++ status = "okay";
++ mediatek,gmac-id = <0>;
++ phy-mode = "sgmii";
++ mediatek,switch = "mt7531";
++ reset-gpios = <&gpio 39 GPIO_ACTIVE_HIGH>;
++
++ fixed-link {
++ speed = <1000>;
++ full-duplex;
++ };
++};
++
++&pinctrl {
++ spi_flash_pins: spi0-pins-func-1 {
++ mux {
++ function = "flash";
++ groups = "spi0", "spi0_wp_hold";
++ };
++
++ conf-pu {
++ pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
++ drive-strength = <MTK_DRIVE_8mA>;
++ bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
++ };
++
++ conf-pd {
++ pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
++ drive-strength = <MTK_DRIVE_8mA>;
++ bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
++ };
++ };
++
++ spic_pins: spi1-pins-func-1 {
++ mux {
++ function = "spi";
++ groups = "spi1_1";
++ };
++ };
++
++ uart1_pins: spi1-pins-func-3 {
++ mux {
++ function = "uart";
++ groups = "uart1_2";
++ };
++ };
++
++ pwm_pins: pwm0-pins-func-1 {
++ mux {
++ function = "pwm";
++ groups = "pwm0_1", "pwm1_0";
++ };
++ };
++};
++
++&pwm {
++ pinctrl-names = "default";
++ pinctrl-0 = <&pwm_pins>;
++ status = "okay";
++};
++
++&spi0 {
++ #address-cells = <1>;
++ #size-cells = <0>;
++ pinctrl-names = "default";
++ pinctrl-0 = <&spi_flash_pins>;
++ status = "okay";
++ must_tx;
++ enhance_timing;
++ dma_ext;
++ ipm_design;
++ support_quad;
++ tick_dly = <2>;
++ sample_sel = <0>;
++
++ spi_nand at 0 {
++ compatible = "spi-nand";
++ reg = <0>;
++ spi-max-frequency = <52000000>;
++
++ partitions {
++ compatible = "fixed-partitions";
++ #address-cells = <1>;
++ #size-cells = <1>;
++
++ partition at 0 {
++ label = "bl2";
++ reg = <0x00 0x100000>;
++ };
++
++ partition at 100000 {
++ label = "Nvram";
++ reg = <0x100000 0x40000>;
++ };
++
++ partition at 140000 {
++ label = "Bdata";
++ reg = <0x140000 0x40000>;
++ };
++
++ partition at 180000 {
++ label = "factory";
++ reg = <0x180000 0x200000>;
++ };
++
++ partition at 380000 {
++ label = "fip";
++ reg = <0x380000 0x200000>;
++ };
++
++ partition at 580000 {
++ label = "crash";
++ reg = <0x580000 0x40000>;
++ };
++
++ partition at 5c0000 {
++ label = "crash_log";
++ reg = <0x5c0000 0x40000>;
++ };
++
++ partition at 600000 {
++ label = "ubi";
++ reg = <0x600000 0x7000000>;
++ };
++
++ partition at 7600000 {
++ label = "KF";
++ reg = <0x7600000 0x40000>;
++ };
++ };
++ };
++};
++
++&watchdog {
++ status = "disabled";
++};
+--- /dev/null
++++ b/xiaomi_mi-router-wr30u_env
+@@ -0,0 +1,56 @@
++ipaddr=192.168.1.1
++serverip=192.168.1.254
++loadaddr=0x46000000
++console=earlycon=uart8250,mmio32,0x11002000 console=ttyS0
++bootcmd=if pstore check ; then run boot_recovery ; else run boot_ubi ; fi
++bootconf=config-1
++bootdelay=0
++bootfile=openwrt-mediatek-filogic-xiaomi_mi-router-wr30u-ubootmod-initramfs-recovery.itb
++bootfile_bl2=openwrt-mediatek-filogic-xiaomi_mi-router-wr30u-ubootmod-preloader.bin
++bootfile_fip=openwrt-mediatek-filogic-xiaomi_mi-router-wr30u-ubootmod-bl31-uboot.fip
++bootfile_upg=openwrt-mediatek-filogic-xiaomi_mi-router-wr30u-ubootmod-squashfs-sysupgrade.itb
++bootled_pwr=yellow:system
++bootled_rec=yellow:network
++bootmenu_confirm_return=askenv - Press ENTER to return to menu ; bootmenu 60
++bootmenu_default=0
++bootmenu_delay=0
++bootmenu_title= [0;34m( ( ( [1;39mOpenWrt[0;34m ) ) )
++bootmenu_0=Initialize environment.=run _firstboot
++bootmenu_0d=Run default boot command.=run boot_default
++bootmenu_1=Boot system via TFTP.=run boot_tftp ; run bootmenu_confirm_return
++bootmenu_2=Boot production system from NAND.=run boot_production ; run bootmenu_confirm_return
++bootmenu_3=Boot recovery system from NAND.=run boot_recovery ; run bootmenu_confirm_return
++bootmenu_4=Load production system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_production ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
++bootmenu_5=Load recovery system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_recovery ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
++bootmenu_6=[31mLoad BL31+U-Boot FIP via TFTP then write to NAND.[0m=run boot_tftp_write_fip ; run bootmenu_confirm_return
++bootmenu_7=[31mLoad BL2 preloader via TFTP then write to NAND.[0m=run boot_tftp_write_bl2 ; run bootmenu_confirm_return
++bootmenu_8=Reboot.=reset
++bootmenu_9=Reset all settings to factory defaults.=run reset_factory ; reset
++boot_first=if button reset ; then led $bootled_rec on ; run boot_tftp_recovery ; setenv flag_recover 1 ; run boot_default ; fi ; bootmenu
++boot_default=if env exists flag_recover ; then else run bootcmd ; fi ; run boot_recovery ; setenv replacevol 1 ; run boot_tftp_forever
++boot_production=led $bootled_pwr on ; run ubi_read_production && bootm $loadaddr#$bootconf ; led $bootled_pwr off
++boot_recovery=led $bootled_rec on ; run ubi_read_recovery && bootm $loadaddr#$bootconf ; led $bootled_rec off
++boot_ubi=run boot_production ; run boot_recovery ; run boot_tftp_forever
++boot_tftp_forever=led $bootled_rec on ; while true ; do run boot_tftp_recovery ; sleep 1 ; done
++boot_tftp_production=tftpboot $loadaddr $bootfile_upg && env exists replacevol && iminfo $loadaddr && run ubi_write_production ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
++boot_tftp_recovery=tftpboot $loadaddr $bootfile && env exists replacevol && iminfo $loadaddr && run ubi_write_recovery ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
++boot_tftp=tftpboot $loadaddr $bootfile && bootm $loadaddr#$bootconf
++boot_tftp_write_fip=tftpboot $loadaddr $bootfile_fip && run mtd_write_fip && run reset_factory
++boot_tftp_write_bl2=tftpboot $loadaddr $bootfile_bl2 && run mtd_write_bl2
++part_default=production
++part_recovery=recovery
++reset_factory=ubi part ubi ; mw $loadaddr 0x0 0x800 ; ubi write $loadaddr ubootenv 0x800 ; ubi write $loadaddr ubootenv2 0x800
++mtd_write_fip=mtd erase fip && mtd write fip $loadaddr
++mtd_write_bl2=mtd erase bl2 && mtd write bl2 $loadaddr
++ubi_create_env=ubi check ubootenv || ubi create ubootenv 0x100000 dynamic 0 || run ubi_format ; ubi check ubootenv2 || ubi create ubootenv2 0x100000 dynamic 1 || run ubi_format
++ubi_format=ubi detach ; mtd erase ubi && ubi part ubi ; reset
++ubi_prepare_rootfs=if ubi check rootfs_data ; then else if env exists rootfs_data_max ; then ubi create rootfs_data $rootfs_data_max dynamic || ubi create rootfs_data - dynamic ; else ubi create rootfs_data - dynamic ; fi ; fi
++ubi_read_production=ubi read $loadaddr fit && iminfo $loadaddr && run ubi_prepare_rootfs
++ubi_read_recovery=ubi check recovery && ubi read $loadaddr recovery
++ubi_remove_rootfs=ubi check rootfs_data && ubi remove rootfs_data
++ubi_write_production=ubi check fit && ubi remove fit ; run ubi_remove_rootfs ; ubi create fit $filesize dynamic 2 && ubi write $loadaddr fit $filesize
++ubi_write_recovery=ubi check recovery && ubi remove recovery ; run ubi_remove_rootfs ; ubi create recovery $filesize dynamic 3 && ubi write $loadaddr recovery $filesize
++_init_env=setenv _init_env ; run ubi_create_env ; saveenv ; saveenv
++_firstboot=setenv _firstboot ; run _switch_to_menu ; run _init_env ; run boot_first
++_switch_to_menu=setenv _switch_to_menu ; setenv bootdelay 3 ; setenv bootmenu_delay 3 ; setenv bootmenu_0 $bootmenu_0d ; setenv bootmenu_0d ; run _bootmenu_update_title
++_bootmenu_update_title=setenv _bootmenu_update_title ; setenv bootmenu_title "$bootmenu_title [33m$ver[0m"
More information about the lede-commits
mailing list