[openwrt/openwrt] mpc85xx: add support for Enterasys WS-AP3715i
LEDE Commits
lede-commits at lists.infradead.org
Sat Apr 8 05:47:25 PDT 2023
blocktrron pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/765f66810a3324cc35fa6471ee8eeee335ba8c2b
commit 765f66810a3324cc35fa6471ee8eeee335ba8c2b
Author: David Bauer <mail at david-bauer.net>
AuthorDate: Sat Mar 18 02:28:23 2023 +0100
mpc85xx: add support for Enterasys WS-AP3715i
Hardware
--------
SoC: NXP P1010 (1x e500 @ 800MHz)
RAM: 256M DDR3 (2x Samsung K4B1G1646G-BCH9)
FLASH: 32M NOR (Spansion S25FL256S)
BTN: 1x Reset
WiFi: 1x Atheros AR9590 2.4 bgn 3x3
2x Atheros AR9590 5.0 an 3x3
ETH: 2x Gigabit Ethernet (Atheros AR8033 / AR8035)
UART: 115200 8N1 (RJ-45 Cisco)
Installation
------------
1. Grab the OpenWrt initramfs, rename it to ap3715.bin. Place it in
the root directory of a TFTP server and serve it at
192.168.1.66/24.
2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot
by pressing Enter when prompted. Credentials are identical to the one
in the APs interface. By default it is admin / new2day.
3. Alter the bootcmd in U-Boot:
$ setenv ramboot_openwrt "setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66; tftpboot 0x2000000 ap3715.bin; bootm"
$ setenv boot_openwrt "sf probe 0; sf read 0x2000000 0x140000 0x1000000;
bootm 0x2000000"
$ setenv bootcmd "run boot_openwrt"
$ saveenv
4. Boot the initramfs image
$ run ramboot_openwrt
5. Transfer the OpenWrt sysupgrade image to the AP using SCP. Install
using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Signed-off-by: David Bauer <mail at david-bauer.net>
---
package/boot/uboot-envtools/files/mpc85xx | 4 +
.../linux/mpc85xx/base-files/etc/board.d/01_leds | 1 +
.../mpc85xx/base-files/etc/board.d/02_network | 3 +-
.../etc/hotplug.d/ieee80211/10-fix-wifi-mac | 4 +
.../base-files/lib/preinit/10_fix_eth_mac.sh | 1 +
target/linux/mpc85xx/config-5.15 | 1 +
.../files/arch/powerpc/boot/dts/ws-ap3715i.dts | 293 +++++++++++++++++++++
.../files/arch/powerpc/platforms/85xx/ws-ap3715i.c | 87 ++++++
target/linux/mpc85xx/image/p1010.mk | 13 +
target/linux/mpc85xx/p1010/config-default | 4 +
target/linux/mpc85xx/p1010/target.mk | 2 +-
.../109-powerpc-85xx-add-ws-ap3715i-support.patch | 50 ++++
.../109-powerpc-85xx-add-ws-ap3715i-support.patch | 50 ++++
13 files changed, 511 insertions(+), 2 deletions(-)
diff --git a/package/boot/uboot-envtools/files/mpc85xx b/package/boot/uboot-envtools/files/mpc85xx
index 6d389c5b57..a74466ab3a 100644
--- a/package/boot/uboot-envtools/files/mpc85xx
+++ b/package/boot/uboot-envtools/files/mpc85xx
@@ -8,6 +8,10 @@ touch /etc/config/ubootenv
board=$(board_name)
case "$board" in
+enterasys,ws-ap3715i)
+ ubootenv_add_uci_config "$(find_mtd_part 'cfg1')" "0x0" "0x10000" "0x10000"
+ ubootenv_add_uci_config "$(find_mtd_part 'cfg2')" "0x0" "0x10000" "0x10000"
+ ;;
extreme-networks,ws-ap3825i)
ubootenv_add_uci_config "$(find_mtd_part 'cfg1')" "0x0" "0x10000" "0x20000"
ubootenv_add_uci_config "$(find_mtd_part 'cfg2')" "0x0" "0x10000" "0x20000"
diff --git a/target/linux/mpc85xx/base-files/etc/board.d/01_leds b/target/linux/mpc85xx/base-files/etc/board.d/01_leds
index 391c909e4c..d9b4d2d79d 100644
--- a/target/linux/mpc85xx/base-files/etc/board.d/01_leds
+++ b/target/linux/mpc85xx/base-files/etc/board.d/01_leds
@@ -8,6 +8,7 @@ boardname="${board##*,}"
board_config_update
case $board in
+enterasys,ws-ap3715i|\
extreme-networks,ws-ap3825i)
ucidef_set_led_netdev "lan1" "LAN1" "green:lan1" "eth1"
ucidef_set_led_netdev "lan2" "LAN2" "green:lan2" "eth0"
diff --git a/target/linux/mpc85xx/base-files/etc/board.d/02_network b/target/linux/mpc85xx/base-files/etc/board.d/02_network
index 77e208c7fa..04c27769a9 100644
--- a/target/linux/mpc85xx/base-files/etc/board.d/02_network
+++ b/target/linux/mpc85xx/base-files/etc/board.d/02_network
@@ -9,7 +9,8 @@ board_config_update
board=$(board_name)
case "$board" in
-aerohive,hiveap-330)
+aerohive,hiveap-330|\
+enterasys,ws-ap3715i)
ucidef_set_interfaces_lan_wan "eth1" "eth0"
;;
ocedo,panda)
diff --git a/target/linux/mpc85xx/base-files/etc/hotplug.d/ieee80211/10-fix-wifi-mac b/target/linux/mpc85xx/base-files/etc/hotplug.d/ieee80211/10-fix-wifi-mac
index 8050c7bea2..20ad8eb44f 100644
--- a/target/linux/mpc85xx/base-files/etc/hotplug.d/ieee80211/10-fix-wifi-mac
+++ b/target/linux/mpc85xx/base-files/etc/hotplug.d/ieee80211/10-fix-wifi-mac
@@ -12,6 +12,10 @@ PHYNBR=${DEVPATH##*/phy}
board=$(board_name)
case "$board" in
+enterasys,ws-ap3715i)
+ [ "$PHYNBR" -eq 0 ] && mtd_get_mac_ascii cfg2 RADIOADDR1 > /sys${DEVPATH}/macaddress
+ [ "$PHYNBR" -eq 1 ] && mtd_get_mac_ascii cfg2 RADIOADDR0 > /sys${DEVPATH}/macaddress
+ ;;
enterasys,ws-ap3710i|\
extreme-networks,ws-ap3825i)
mtd_get_mac_ascii cfg2 RADIOADDR${PHYNBR} > /sys${DEVPATH}/macaddress
diff --git a/target/linux/mpc85xx/base-files/lib/preinit/10_fix_eth_mac.sh b/target/linux/mpc85xx/base-files/lib/preinit/10_fix_eth_mac.sh
index 0d9058420b..ddb9bef141 100644
--- a/target/linux/mpc85xx/base-files/lib/preinit/10_fix_eth_mac.sh
+++ b/target/linux/mpc85xx/base-files/lib/preinit/10_fix_eth_mac.sh
@@ -3,6 +3,7 @@
preinit_set_mac_address() {
case $(board_name) in
+ enterasys,ws-ap3715i|\
extreme-networks,ws-ap3825i)
ip link set dev eth0 address $(mtd_get_mac_ascii cfg1 ethaddr)
ip link set dev eth1 address $(mtd_get_mac_ascii cfg1 eth1addr)
diff --git a/target/linux/mpc85xx/config-5.15 b/target/linux/mpc85xx/config-5.15
index ab2eef94cd..42d17c1361 100644
--- a/target/linux/mpc85xx/config-5.15
+++ b/target/linux/mpc85xx/config-5.15
@@ -262,6 +262,7 @@ CONFIG_VDSO32=y
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_WATCHDOG_CORE=y
# CONFIG_WS_AP3710I is not set
+# CONFIG_WS_AP3715I is not set
# CONFIG_WS_AP3825I is not set
# CONFIG_XES_MPC85xx is not set
CONFIG_XZ_DEC_BCJ=y
diff --git a/target/linux/mpc85xx/files/arch/powerpc/boot/dts/ws-ap3715i.dts b/target/linux/mpc85xx/files/arch/powerpc/boot/dts/ws-ap3715i.dts
new file mode 100644
index 0000000000..d13952acae
--- /dev/null
+++ b/target/linux/mpc85xx/files/arch/powerpc/boot/dts/ws-ap3715i.dts
@@ -0,0 +1,293 @@
+// SPDX-License-Identifier: GPL-2.0-or-later or MIT
+
+#include <dt-bindings/gpio/gpio.h>
+
+/include/ "fsl/p1010si-pre.dtsi"
+
+/ {
+ model = "Enterasys WS-AP3715i";
+ compatible = "enterasys,ws-ap3715i";
+
+ aliases {
+ led-boot = &led_power_green;
+ led-failsafe = &led_power_red;
+ led-running = &led_power_green;
+ led-upgrade = &led_power_red;
+ label-mac-device = &enet0;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x10000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ wifi1 {
+ gpios = <&spi_gpio 3 GPIO_ACTIVE_HIGH>;
+ label = "green:radio1";
+ linux,default-trigger = "phy1tpt";
+ };
+
+ wifi2 {
+ gpios = <&spi_gpio 2 GPIO_ACTIVE_HIGH>;
+ label = "green:radio2";
+ linux,default-trigger = "phy0tpt";
+ };
+
+ led_power_green: power_green {
+ gpios = <&spi_gpio 0 GPIO_ACTIVE_HIGH>;
+ label = "green:power";
+ };
+
+ led_power_red: power_red {
+ gpios = <&spi_gpio 1 GPIO_ACTIVE_HIGH>;
+ label = "red:power";
+ };
+
+ lan1_red {
+ gpios = <&spi_gpio 6 GPIO_ACTIVE_HIGH>;
+ label = "red:lan1";
+ };
+
+ lan1_green {
+ gpios = <&spi_gpio 4 GPIO_ACTIVE_HIGH>;
+ label = "green:lan1";
+ };
+
+ lan2_red {
+ gpios = <&spi_gpio 7 GPIO_ACTIVE_HIGH>;
+ label = "red:lan2";
+ };
+
+ lan2_green {
+ gpios = <&spi_gpio 5 GPIO_ACTIVE_HIGH>;
+ label = "green:lan2";
+ };
+ };
+
+ soc: soc at ffe00000 {
+ ranges = <0x0 0x0 0xffe00000 0x100000>;
+
+ gpio0: gpio-controller at fc00 {
+ };
+
+ usb at 22000 {
+ status = "disabled";
+ };
+
+ mdio at 24000 {
+ phy0: ethernet-phy at 0 {
+ reg = <0x1>;
+ };
+
+ phy2: ethernet-phy at 2 {
+ reg = <0x2>;
+ };
+ };
+
+ mdio at 25000 {
+ tbi_phy: tbi-phy at 11 {
+ reg = <0x11>;
+ };
+ };
+
+ mdio at 26000 {
+ status = "disabled";
+ };
+
+ enet0: ethernet at b0000 {
+ phy-handle = <&phy0>;
+ phy-connection-type = "rgmii-id";
+
+ label = "lan1";
+ };
+
+ enet1: ethernet at b1000 {
+ phy-handle = <&phy2>;
+ phy-connection-type = "sgmii";
+
+ tbi-handle = <&tbi_phy>;
+
+ label = "lan2";
+ };
+
+ enet2: ethernet at b2000 {
+ status = "disabled";
+ };
+
+ sdhc at 2e000 {
+ status = "disabled";
+ };
+ };
+
+ ifc: ifc at ffe1e000 {
+ };
+
+ pci0: pcie at ffe09000 {
+ reg = <0 0xffe09000 0 0x1000>;
+ ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
+ pcie at 0 {
+ ranges = <0x2000000 0x0 0xa0000000
+ 0x2000000 0x0 0xa0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+
+ wifi at 0,0,0 {
+ compatible = "pci168c,0033";
+ reg = <0x0 0 0 0 0>;
+ ieee80211-freq-limit = <2400000 2500000>;
+ };
+ };
+ };
+
+ pci1: pcie at ffe0a000 {
+ reg = <0 0xffe0a000 0 0x1000>;
+ ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
+ pcie at 0 {
+ ranges = <0x2000000 0x0 0x80000000
+ 0x2000000 0x0 0x80000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+
+ wifi at 0,0,0 {
+ compatible = "pci168c,0033";
+ reg = <0x0 0 0 0 0>;
+ ieee80211-freq-limit = <5000000 6000000>;
+ };
+ };
+ };
+};
+
+&soc {
+ led_spi {
+ compatible = "spi-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sck-gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>;
+ mosi-gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>;
+ num-chipselects = <0>;
+
+ spi_gpio: led_gpio at 0 {
+ compatible = "fairchild,74hc595";
+ reg = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ registers-number = <1>;
+ spi-max-frequency = <100000>;
+ };
+ };
+
+ spi0: spi at 7000 {
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ reg = <0x0 0xa0000>;
+ label = "boot-bak";
+ read-only;
+ };
+
+ partition at a0000 {
+ reg = <0xa0000 0xa0000>;
+ label = "boot-pri";
+ read-only;
+ };
+
+ partition at 120000 {
+ reg = <0x120000 0x10000>;
+ label = "cfg1";
+ read-only;
+ };
+
+ partition at 130000 {
+ reg = <0x130000 0x10000>;
+ label = "cfg2";
+ read-only;
+ };
+
+ partition at 140000 {
+ compatible = "denx,uimage";
+ reg = <0x140000 0x1d80000>;
+ label = "firmware";
+ };
+
+ partition at 1ec0000 {
+ reg = <0x1ec0000 0x100000>;
+ label = "nvram";
+ read-only;
+ };
+ };
+ };
+ };
+};
+
+/include/ "fsl/p1010si-post.dtsi"
+
+/ {
+ cpus {
+ PowerPC,P1010 at 0 {
+ bus-frequency = <399999996>;
+ timebase-frequency = <50000000>;
+ clock-frequency = <799999992>;
+ d-cache-block-size = <0x20>;
+ d-cache-size = <0x8000>;
+ d-cache-sets = <0x80>;
+ i-cache-block-size = <0x20>;
+ i-cache-size = <0x8000>;
+ i-cache-sets = <0x80>;
+ };
+ };
+
+ soc at ffe00000 {
+ bus-frequency = <399999996>;
+
+ serial at 4600 {
+ clock-frequency = <399999996>;
+ status = "disabled";
+ };
+
+ serial at 4500 {
+ clock-frequency = <399999996>;
+ };
+
+ pic at 40000 {
+ clock-frequency = <399999996>;
+ };
+ };
+};
+
+/*
+ * For the OpenWrt 22.03 release, since Linux 5.10.138 now uses
+ * aliases to determine PCI domain numbers, drop aliases so as not to
+ * change the sysfs path of our wireless netdevs.
+ */
+
+/ {
+ aliases {
+ /delete-property/ pci0;
+ /delete-property/ pci1;
+ };
+};
+
diff --git a/target/linux/mpc85xx/files/arch/powerpc/platforms/85xx/ws-ap3715i.c b/target/linux/mpc85xx/files/arch/powerpc/platforms/85xx/ws-ap3715i.c
new file mode 100644
index 0000000000..aa2a366b3d
--- /dev/null
+++ b/target/linux/mpc85xx/files/arch/powerpc/platforms/85xx/ws-ap3715i.c
@@ -0,0 +1,87 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+/*
+ * Enterasys WS-AP3715i Board Setup
+ *
+ * Copyright (C) 2023 David Bauer <mail at david-bauer.net>
+ *
+ * Based on:
+ * p1010rdb.c:
+ * P1010 RDB Board Setup
+ * Copyright 2011 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/of_platform.h>
+
+#include <asm/time.h>
+#include <asm/machdep.h>
+#include <asm/pci-bridge.h>
+#include <mm/mmu_decl.h>
+#include <asm/prom.h>
+#include <asm/udbg.h>
+#include <asm/mpic.h>
+
+#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
+
+#include "mpc85xx.h"
+
+void __init wsap3715i_pic_init(void)
+{
+ struct mpic *mpic;
+
+ mpic = mpic_alloc(NULL, 0,
+ MPIC_BIG_ENDIAN | MPIC_SINGLE_DEST_CPU,
+ 0, 256, " OpenPIC ");
+
+ BUG_ON(mpic == NULL);
+ mpic_init(mpic);
+}
+
+/*
+ * Setup the architecture
+ */
+static void __init wsap3715i_setup_arch(void)
+{
+ if (ppc_md.progress)
+ ppc_md.progress("wsap3715i_setup_arch()", 0);
+
+ fsl_pci_assign_primary();
+
+ pr_info("WS-AP3715i from Enterasys\n");
+}
+
+machine_arch_initcall(wsap3715i, mpc85xx_common_publish_devices);
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+static int __init wsap3715i_probe(void)
+{
+ if (of_machine_is_compatible("enterasys,ws-ap3715i"))
+ return 1;
+ return 0;
+}
+
+define_machine(wsap3715i) {
+ .name = "P1010 RDB",
+ .probe = wsap3715i_probe,
+ .setup_arch = wsap3715i_setup_arch,
+ .init_IRQ = wsap3715i_pic_init,
+#ifdef CONFIG_PCI
+ .pcibios_fixup_bus = fsl_pcibios_fixup_bus,
+ .pcibios_fixup_phb = fsl_pcibios_fixup_phb,
+#endif
+ .get_irq = mpic_get_irq,
+ .calibrate_decr = generic_calibrate_decr,
+ .progress = udbg_progress,
+};
diff --git a/target/linux/mpc85xx/image/p1010.mk b/target/linux/mpc85xx/image/p1010.mk
index 90ef46d709..034f6abc40 100644
--- a/target/linux/mpc85xx/image/p1010.mk
+++ b/target/linux/mpc85xx/image/p1010.mk
@@ -14,6 +14,19 @@ define Build/spi-loader-okli
mv "$@.new" "$@"
endef
+define Device/enterasys_ws-ap3715i
+ DEVICE_VENDOR := Enterasys
+ DEVICE_MODEL := WS-AP3715i
+ BLOCKSIZE := 64k
+ KERNEL_NAME := simpleImage.ws-ap3715i
+ KERNEL_ENTRY := 0x1000000
+ KERNEL_LOADADDR := 0x1000000
+ KERNEL = kernel-bin | lzma | uImage lzma
+ IMAGES := sysupgrade.bin
+ IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
+endef
+TARGET_DEVICES += enterasys_ws-ap3715i
+
define Device/tplink_tl-wdr4900-v1
DEVICE_VENDOR := TP-Link
DEVICE_MODEL := TL-WDR4900
diff --git a/target/linux/mpc85xx/p1010/config-default b/target/linux/mpc85xx/p1010/config-default
index 53e077b6c2..6af6b8e097 100644
--- a/target/linux/mpc85xx/p1010/config-default
+++ b/target/linux/mpc85xx/p1010/config-default
@@ -1,9 +1,11 @@
CONFIG_AT803X_PHY=y
CONFIG_CMDLINE_OVERRIDE=y
# CONFIG_FSL_CORENET_CF is not set
+CONFIG_GPIO_74X164=y
CONFIG_MTD_NAND_FSL_IFC=y
CONFIG_MTD_SPLIT_FIRMWARE=y
CONFIG_MTD_SPLIT_TPLINK_FW=y
+CONFIG_MTD_SPLIT_UIMAGE_FW=y
CONFIG_MTD_UBI=y
CONFIG_MTD_UBI_BEB_LIMIT=20
CONFIG_MTD_UBI_BLOCK=y
@@ -18,6 +20,8 @@ CONFIG_REALTEK_PHY=y
CONFIG_RED_15W_REV1=y
CONFIG_REGMAP=y
CONFIG_REGULATOR=y
+CONFIG_SPI_GPIO=y
CONFIG_TL_WDR4900_V1=y
CONFIG_UBIFS_FS=y
+CONFIG_WS_AP3715I=y
CONFIG_FIREBOX_T10=y
\ No newline at end of file
diff --git a/target/linux/mpc85xx/p1010/target.mk b/target/linux/mpc85xx/p1010/target.mk
index 86628e32da..fa1bb7542d 100644
--- a/target/linux/mpc85xx/p1010/target.mk
+++ b/target/linux/mpc85xx/p1010/target.mk
@@ -1,5 +1,5 @@
BOARDNAME:=P1010
-KERNEL_IMAGES:=simpleImage.tl-wdr4900-v1
+KERNEL_IMAGES:=simpleImage.tl-wdr4900-v1 simpleImage.ws-ap3715i
define Target/Description
Build firmware images for P1010 based boards.
diff --git a/target/linux/mpc85xx/patches-5.10/109-powerpc-85xx-add-ws-ap3715i-support.patch b/target/linux/mpc85xx/patches-5.10/109-powerpc-85xx-add-ws-ap3715i-support.patch
new file mode 100644
index 0000000000..10ba744897
--- /dev/null
+++ b/target/linux/mpc85xx/patches-5.10/109-powerpc-85xx-add-ws-ap3715i-support.patch
@@ -0,0 +1,50 @@
+--- a/arch/powerpc/platforms/85xx/Kconfig
++++ b/arch/powerpc/platforms/85xx/Kconfig
+@@ -82,6 +82,17 @@ config WS_AP3710I
+ This board is a Concurrent Dual-Band wireless access point with a
+ Freescale P1020 SoC.
+
++config WS_AP3715I
++ bool "Enterasys WS-AP3715i"
++ select DEFAULT_UIMAGE
++ select ARCH_REQUIRE_GPIOLIB
++ select GPIO_MPC8XXX
++ help
++ This option enables support for the Enterasys WS-AP3715i board.
++
++ This board is a Concurrent Dual-Band wireless access point with a
++ Freescale P1010 SoC.
++
+ config WS_AP3825I
+ bool "Extreme Networks WS-AP3825i"
+ select DEFAULT_UIMAGE
+--- a/arch/powerpc/platforms/85xx/Makefile
++++ b/arch/powerpc/platforms/85xx/Makefile
+@@ -27,6 +27,7 @@ obj-$(CONFIG_P1023_RDB) += p1023_rdb.o
+ obj-$(CONFIG_PANDA) += panda.o
+ obj-$(CONFIG_TWR_P102x) += twr_p102x.o
+ obj-$(CONFIG_WS_AP3710I) += ws-ap3710i.o
++obj-$(CONFIG_WS_AP3715I) += ws-ap3715i.o
+ obj-$(CONFIG_WS_AP3825I) += ws-ap3825i.o
+ obj-$(CONFIG_FIREBOX_T10) += firebox_t10.o
+ obj-$(CONFIG_CORENET_GENERIC) += corenet_generic.o
+--- a/arch/powerpc/boot/Makefile
++++ b/arch/powerpc/boot/Makefile
+@@ -340,6 +340,7 @@ image-$(CONFIG_TQM8560) += cuImage.tqm
+ image-$(CONFIG_SBC8548) += cuImage.sbc8548
+ image-$(CONFIG_KSI8560) += cuImage.ksi8560
+ image-$(CONFIG_TL_WDR4900_V1) += simpleImage.tl-wdr4900-v1
++image-$(CONFIG_WS_AP3715I) += simpleImage.ws-ap3715i
+ image-$(CONFIG_WS_AP3825I) += simpleImage.ws-ap3825i
+ # Board ports in arch/powerpc/platform/86xx/Kconfig
+ image-$(CONFIG_MVME7100) += dtbImage.mvme7100
+--- a/arch/powerpc/boot/wrapper
++++ b/arch/powerpc/boot/wrapper
+@@ -324,6 +324,7 @@ adder875-redboot)
+ platformo="$object/fixed-head.o $object/redboot-8xx.o"
+ binary=y
+ ;;
++simpleboot-ws-ap3715i|\
+ simpleboot-ws-ap3825i|\
+ simpleboot-tl-wdr4900-v1)
+ platformo="$object/fixed-head.o $object/simpleboot.o"
diff --git a/target/linux/mpc85xx/patches-5.15/109-powerpc-85xx-add-ws-ap3715i-support.patch b/target/linux/mpc85xx/patches-5.15/109-powerpc-85xx-add-ws-ap3715i-support.patch
new file mode 100644
index 0000000000..8272d9dd2a
--- /dev/null
+++ b/target/linux/mpc85xx/patches-5.15/109-powerpc-85xx-add-ws-ap3715i-support.patch
@@ -0,0 +1,50 @@
+--- a/arch/powerpc/platforms/85xx/Kconfig
++++ b/arch/powerpc/platforms/85xx/Kconfig
+@@ -82,6 +82,17 @@ config WS_AP3710I
+ This board is a Concurrent Dual-Band wireless access point with a
+ Freescale P1020 SoC.
+
++config WS_AP3715I
++ bool "Enterasys WS-AP3715i"
++ select DEFAULT_UIMAGE
++ select ARCH_REQUIRE_GPIOLIB
++ select GPIO_MPC8XXX
++ help
++ This option enables support for the Enterasys WS-AP3715i board.
++
++ This board is a Concurrent Dual-Band wireless access point with a
++ Freescale P1010 SoC.
++
+ config WS_AP3825I
+ bool "Extreme Networks WS-AP3825i"
+ select DEFAULT_UIMAGE
+--- a/arch/powerpc/platforms/85xx/Makefile
++++ b/arch/powerpc/platforms/85xx/Makefile
+@@ -27,6 +27,7 @@ obj-$(CONFIG_P1023_RDB) += p1023_rdb.o
+ obj-$(CONFIG_PANDA) += panda.o
+ obj-$(CONFIG_TWR_P102x) += twr_p102x.o
+ obj-$(CONFIG_WS_AP3710I) += ws-ap3710i.o
++obj-$(CONFIG_WS_AP3715I) += ws-ap3715i.o
+ obj-$(CONFIG_WS_AP3825I) += ws-ap3825i.o
+ obj-$(CONFIG_FIREBOX_T10) += firebox_t10.o
+ obj-$(CONFIG_CORENET_GENERIC) += corenet_generic.o
+--- a/arch/powerpc/boot/Makefile
++++ b/arch/powerpc/boot/Makefile
+@@ -346,6 +346,7 @@ image-$(CONFIG_TQM8555) += cuImage.tqm
+ image-$(CONFIG_TQM8560) += cuImage.tqm8560
+ image-$(CONFIG_KSI8560) += cuImage.ksi8560
+ image-$(CONFIG_TL_WDR4900_V1) += simpleImage.tl-wdr4900-v1
++image-$(CONFIG_WS_AP3715I) += simpleImage.ws-ap3715i
+ image-$(CONFIG_WS_AP3825I) += simpleImage.ws-ap3825i
+ # Board ports in arch/powerpc/platform/86xx/Kconfig
+ image-$(CONFIG_MVME7100) += dtbImage.mvme7100
+--- a/arch/powerpc/boot/wrapper
++++ b/arch/powerpc/boot/wrapper
+@@ -326,6 +326,7 @@ adder875-redboot)
+ platformo="$object/fixed-head.o $object/redboot-8xx.o"
+ binary=y
+ ;;
++simpleboot-ws-ap3715i|\
+ simpleboot-ws-ap3825i|\
+ simpleboot-tl-wdr4900-v1)
+ platformo="$object/fixed-head.o $object/simpleboot.o"
More information about the lede-commits
mailing list