[openwrt/openwrt] ramips: Add support for D-Link DIR-3060 A1
LEDE Commits
lede-commits at lists.infradead.org
Sun Nov 13 14:31:47 PST 2022
hauke pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/6afc355b2e120ff2701cc9aca66af19c6a0aeca2
commit 6afc355b2e120ff2701cc9aca66af19c6a0aeca2
Author: Ivaylo Ivanov <iivailo at mail.bg>
AuthorDate: Thu Aug 25 09:10:13 2022 +0300
ramips: Add support for D-Link DIR-3060 A1
Hardware specification:
SoC: MediaTek MT7621AT
Flash: Winbond W29N01HVSINA 128MB
RAM: Micron MT41K128M16JT-125 256MB
Ethernet: 4x 10/100/1000 Mbps
WiFi1: MT7615DN 2.4GHz N 2x2:2
WiFi2: MT7615DN 5GHz AC 2x2:2
WiFi3: MT7615N 5GHz AC 4x4:4
Button: WPS, Reset
Flash instructions:
OpenWrt can be installed via D-Link Recovery GUI:
Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable.
Give it ~30 seconds, to boot the recovery mode GUI
Connect your client computer to LAN1 of the device
Set your client IP address manually to 192.168.0.2 / 255.255.255.0.
Call the recovery page for the device at http://192.168.0.1/
Use the provided emergency web GUI to upload and flash a new firmware to the device
Signed-off-by: Ivaylo Ivanov <iivailo at mail.bg>
---
.../linux/ramips/dts/mt7621_dlink_dir-3060-a1.dts | 241 +++++++++++++++++++++
target/linux/ramips/image/mt7621.mk | 7 +
.../ramips/mt7621/base-files/etc/board.d/01_leds | 4 +
.../mt7621/base-files/lib/upgrade/platform.sh | 1 +
4 files changed, 253 insertions(+)
diff --git a/target/linux/ramips/dts/mt7621_dlink_dir-3060-a1.dts b/target/linux/ramips/dts/mt7621_dlink_dir-3060-a1.dts
new file mode 100644
index 0000000000..675a3aa631
--- /dev/null
+++ b/target/linux/ramips/dts/mt7621_dlink_dir-3060-a1.dts
@@ -0,0 +1,241 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "dlink,dir-3060-a1", "mediatek,mt7621-soc";
+ model = "D-Link DIR-3060 A1";
+
+ aliases {
+ label-mac-device = &gmac0;
+ led-boot = &led_power_orange;
+ led-failsafe = &led_power_white;
+ led-running = &led_power_white;
+ led-upgrade = &led_net_orange;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power_orange: power_orange {
+ label = "orange:power";
+ gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+ };
+
+ led_power_white: power_white {
+ label = "white:power";
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ };
+
+ led_net_orange: net_orange {
+ label = "orange:net";
+ gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+ };
+
+ net_white {
+ label = "white:net";
+ gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+ };
+
+ usb2_white {
+ label = "white:usb2";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ trigger-sources = <&ehci_port2>;
+ linux,default-trigger = "usbport";
+ };
+
+ usb3_white {
+ label = "white:usb3";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ trigger-sources = <&xhci_ehci_port1>;
+ linux,default-trigger = "usbport";
+ };
+
+ wlan2g {
+ label = "white:wlan2g";
+ gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0radio";
+ };
+
+ wlan5glb {
+ label = "white:wlan5glb";
+ gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy1radio";
+ };
+
+ wlan5ghb {
+ label = "white:wlan5ghb";
+ gpios = <&gpio 5 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy2radio";
+ };
+ };
+};
+
+&nand {
+ status = "okay";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "Bootloader";
+ reg = <0x0 0x80000>;
+ read-only;
+ };
+
+ partition at 80000 {
+ label = "config";
+ reg = <0x80000 0x80000>;
+ read-only;
+ };
+
+ factory: partition at 100000 {
+ label = "factory";
+ reg = <0x100000 0x40000>;
+ read-only;
+ };
+
+ partition at 140000 {
+ label = "config2";
+ reg = <0x140000 0x40000>;
+ read-only;
+ };
+
+ partition at 180000 {
+ label = "firmware";
+ compatible = "openwrt,uimage", "denx,uimage";
+ openwrt,padding = <96>;
+ reg = <0x180000 0x2800000>;
+ };
+
+ partition at 2980000 {
+ label = "private";
+ reg = <0x2980000 0x2000000>;
+ read-only;
+ };
+
+ partition at 4980000 {
+ label = "firmware2";
+ reg = <0x4980000 0x2800000>;
+ read-only;
+ };
+
+ partition at 7180000 {
+ label = "mydlink";
+ reg = <0x7180000 0x600000>;
+ read-only;
+ };
+
+ partition at 7780000 {
+ label = "reserved";
+ reg = <0x7780000 0x880000>;
+ read-only;
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pcie0 {
+ wifi0: wifi at 0,0 {
+ compatible = "mediatek,mt76";
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x0>;
+ ieee80211-freq-limit = <2400000 6000000>;
+ nvmem-cells = <&macaddr_factory_e000>;
+ nvmem-cell-names = "mac-address";
+ mac-address-increment = <1>;
+ };
+};
+
+&pcie1 {
+ wifi1: wifi at 0,0 {
+ compatible = "mediatek,mt76";
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x8000>;
+ ieee80211-freq-limit = <5000000 6000000>;
+ nvmem-cells = <&macaddr_factory_e000>;
+ nvmem-cell-names = "mac-address";
+ mac-address-increment = <3>;
+ };
+};
+
+&gmac0 {
+ nvmem-cells = <&macaddr_factory_e000>;
+ nvmem-cell-names = "mac-address";
+};
+
+&switch0 {
+ ports {
+ port at 0 {
+ status = "okay";
+ label = "lan4";
+ };
+
+ port at 1 {
+ status = "okay";
+ label = "lan3";
+ };
+
+ port at 2 {
+ status = "okay";
+ label = "lan2";
+ };
+
+ port at 3 {
+ status = "okay";
+ label = "lan1";
+ };
+
+ port at 4 {
+ status = "okay";
+ label = "wan";
+ nvmem-cells = <&macaddr_factory_e006>;
+ nvmem-cell-names = "mac-address";
+ };
+ };
+};
+
+&state_default {
+ gpio {
+ groups = "i2c", "uart3", "jtag", "wdt";
+ function = "gpio";
+ };
+};
+
+&factory {
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_factory_e000: macaddr at e000 {
+ reg = <0xe000 0x6>;
+ };
+
+ macaddr_factory_e006: macaddr at e006 {
+ reg = <0xe006 0x6>;
+ };
+};
diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk
index e7b38aaacf..81ee50e0af 100644
--- a/target/linux/ramips/image/mt7621.mk
+++ b/target/linux/ramips/image/mt7621.mk
@@ -547,6 +547,13 @@ define Device/dlink_dir-2660-a1
endef
TARGET_DEVICES += dlink_dir-2660-a1
+define Device/dlink_dir-3060-a1
+ $(Device/dlink_dir-xx60-a1)
+ DEVICE_MODEL := DIR-3060
+ DEVICE_VARIANT := A1
+endef
+TARGET_DEVICES += dlink_dir-3060-a1
+
define Device/dlink_dir-853-a3
$(Device/dlink_dir-xx60-a1)
DEVICE_MODEL := DIR-853
diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
index 98db9fb9fc..9bac8228a0 100644
--- a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
@@ -55,6 +55,10 @@ dlink,dir-2640-a1|\
dlink,dir-2660-a1)
ucidef_set_led_netdev "wan" "wan" "white:net" "wan"
;;
+dlink,dir-3060-a1)
+ ucidef_set_led_netdev "net_white" "WAN Link" "white:net" "wan" "link"
+ ucidef_set_led_netdev "net_orange" "WAN Activity" "orange:net" "wan" "tx rx"
+ ;;
dlink,dir-853-a3)
ucidef_set_led_netdev "wan" "wan" "blue:net" "wan"
;;
diff --git a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh
index 95bba16194..06a35077dc 100755
--- a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh
@@ -62,6 +62,7 @@ platform_do_upgrade() {
dlink,dir-1960-a1|\
dlink,dir-2640-a1|\
dlink,dir-2660-a1|\
+ dlink,dir-3060-a1|\
dlink,dir-853-a3|\
h3c,tx1800-plus|\
h3c,tx1801-plus|\
More information about the lede-commits
mailing list