[openwrt/openwrt] ath79: add support for Teltonika RUT300
LEDE Commits
lede-commits at lists.infradead.org
Thu Nov 10 13:35:55 PST 2022
dangole pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/e586de8dbf00fac72a37177ba08f74bb1091dd86
commit e586de8dbf00fac72a37177ba08f74bb1091dd86
Author: Daniel Golle <daniel at makrotopia.org>
AuthorDate: Thu Nov 10 14:16:32 2022 +0000
ath79: add support for Teltonika RUT300
Add support for the Teltonika RUT300 rugged industrial Ethernet router
Hardware
--------
SoC: Qualcomm Atheros QCA9531
RAM: 64M DDR2 (EtronTech EM68B16CWQK-25IH)
FLASH: 16M SPI-NOR (Winbond W25Q128)
ETH: 4x 100M LAN (QCA9533 internal AR8229 switch, eth0)
1x 100M WAN (QCA9533 internal PHY, eth1)
UART: 115200 8n1, same debug port as other Teltonika devices
USB: 1 single USB 2.0 host port
BUTTON: Reset
LED: 1x green power LED (always on)
5x yellow Ethernet port LED (controlled by Linux)
WAN port LED is used as boot status and upgrade indicator as
the power LED cannot be controlled in software.
Use the *-factory.bin file to intially flash the device using the
vendor firmware's Web-UI.
Signed-off-by: Daniel Golle <daniel at makrotopia.org>
---
.../linux/ath79/dts/qca9531_teltonika_rut300.dts | 164 +++++++++++++++++++++
.../ath79/generic/base-files/etc/board.d/01_leds | 7 +
.../generic/base-files/etc/board.d/02_network | 5 +
target/linux/ath79/image/generic.mk | 47 ++++++
4 files changed, 223 insertions(+)
diff --git a/target/linux/ath79/dts/qca9531_teltonika_rut300.dts b/target/linux/ath79/dts/qca9531_teltonika_rut300.dts
new file mode 100644
index 0000000000..a4f5fb543b
--- /dev/null
+++ b/target/linux/ath79/dts/qca9531_teltonika_rut300.dts
@@ -0,0 +1,164 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "qca953x.dtsi"
+
+/ {
+ compatible = "teltonika,rut300", "teltonika,rut30x", "qca,qca9531";
+ model = "TELTONIKA RUT300";
+
+ aliases {
+ label-mac-device = ð1;
+ led-boot = &led_wan;
+ led-failsafe = &led_wan;
+ led-running = &led_wan;
+ led-upgrade = &led_wan;
+ serial0 = &uart;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmx_leds_switch>, <&jtag_disable_pins>;
+
+ led_wan: wan {
+ label = "yellow:wan";
+ gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ lan1 {
+ label = "yellow:lan1";
+ gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
+ };
+
+ lan2 {
+ label = "yellow:lan2";
+ gpios = <&gpio 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ lan3 {
+ label = "yellow:lan3";
+ gpios = <&gpio 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ lan4 {
+ label = "yellow:lan4";
+ gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&spi {
+ status = "okay";
+ num-cs = <1>;
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x000000 0x020000>;
+ read-only;
+ };
+
+ config: partition at 20000 {
+ label = "config";
+ reg = <0x020000 0x010000>;
+ read-only;
+ };
+
+ partition at 30000 {
+ label = "art";
+ reg = <0x030000 0x010000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x040000 0xf30000>;
+ };
+
+ partition at f70000 {
+ label = "event-log";
+ reg = <0xf70000 0x090000>;
+ };
+ };
+ };
+};
+
+&usb0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ hub_port0: port at 1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&uart {
+ status = "okay";
+};
+
+&config {
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_config_0: macaddr at 0 {
+ reg = <0x0 0x6>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ phy-handle = <&swphy0>;
+
+ nvmem-cells = <&macaddr_config_0>;
+ nvmem-cell-names = "mac-address";
+ mac-address-increment = <1>;
+};
+
+ð1 {
+ phy-handle = <&swphy4>;
+ nvmem-cells = <&macaddr_config_0>;
+ nvmem-cell-names = "mac-address";
+
+ gmac-config {
+ device = <&gmac>;
+ switch-phy-swap = <1>;
+ };
+};
+
+&pinmux {
+ pmx_leds_switch: leds_switch {
+ // switch port LEDs on GPIO 0~4
+ pinctrl-single,bits = <0x0 0x00000000 0xffffffff>,
+ <0x4 0x00000000 0x000000ff>;
+ };
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index 606a194f7e..7fe9343876 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -337,6 +337,13 @@ teltonika,rut230-v1)
ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth1"
ucidef_set_led_switch "lan" "LAN" "green:lan" "switch0" "0x04"
;;
+teltonika,rut300)
+ ucidef_set_led_netdev "wan" "WAN" "yellow:wan" "eth1"
+ ucidef_set_led_switch "lan1" "LAN1" "yellow:lan1" "switch0" "0x02"
+ ucidef_set_led_switch "lan2" "LAN2" "yellow:lan2" "switch0" "0x10"
+ ucidef_set_led_switch "lan3" "LAN3" "yellow:lan3" "switch0" "0x08"
+ ucidef_set_led_switch "lan4" "LAN4" "yellow:lan4" "switch0" "0x04"
+ ;;
tplink,archer-a7-v5|\
tplink,archer-c7-v4|\
tplink,archer-c7-v5)
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index e47f66c2f2..339005f051 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -193,6 +193,11 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0 at eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
;;
+ teltonika,rut300)
+ ucidef_set_interface_wan "eth1"
+ ucidef_add_switch "switch0" \
+ "0 at eth0" "1:lan:1" "2:lan:4" "3:lan:3" "4:lan:2"
+ ;;
buffalo,wzr-hp-g300nh-rb|\
buffalo,wzr-hp-g300nh-s|\
dlink,dir-825-b1|\
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 11c5669fe4..e5bc73e5a6 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -10,6 +10,7 @@ DEVICE_VARS += SEAMA_SIGNATURE SEAMA_MTDBLOCK
DEVICE_VARS += KERNEL_INITRAMFS_PREFIX DAP_SIGNATURE
DEVICE_VARS += EDIMAX_HEADER_MAGIC EDIMAX_HEADER_MODEL
DEVICE_VARS += OPENMESH_CE_TYPE ZYXEL_MODEL_STRING
+DEVICE_VARS += SUPPORTED_TELTONIKA_DEVICES
define Build/addpattern
-$(STAGING_DIR_HOST)/bin/addpattern -B $(ADDPATTERN_ID) \
@@ -139,6 +140,35 @@ define Build/teltonika-v1-header
@mv $@.new $@
endef
+metadata_json_teltonika = \
+ '{ $(if $(IMAGE_METADATA),$(IMAGE_METADATA)$(comma)) \
+ "metadata_version": "1.1", \
+ "compat_version": "$(call json_quote,$(compat_version))", \
+ "version":"$(call json_quote,$(VERSION_DIST))-$(call json_quote,$(VERSION_NUMBER))-$(call json_quote,$(REVISION))", \
+ "device_code": [".*"], \
+ "hwver": [".*"], \
+ "batch": [".*"], \
+ "serial": [".*"], \
+ $(if $(DEVICE_COMPAT_MESSAGE),"compat_message": "$(call json_quote,$(DEVICE_COMPAT_MESSAGE))"$(comma)) \
+ $(if $(filter-out 1.0,$(compat_version)),"new_supported_devices": \
+ [$(call metadata_devices,$(SUPPORTED_TELTONIKA_DEVICES))]$(comma) \
+ "supported_devices": ["$(call json_quote,$(legacy_supported_message))"]$(comma)) \
+ $(if $(filter 1.0,$(compat_version)),"supported_devices":[$(call metadata_devices,$(SUPPORTED_TELTONIKA_DEVICES))]$(comma)) \
+ "version_wrt": { \
+ "dist": "$(call json_quote,$(VERSION_DIST))", \
+ "version": "$(call json_quote,$(VERSION_NUMBER))", \
+ "revision": "$(call json_quote,$(REVISION))", \
+ "target": "$(call json_quote,$(TARGETID))", \
+ "board": "$(call json_quote,$(if $(BOARD_NAME),$(BOARD_NAME),$(DEVICE_NAME)))" \
+ }, \
+ "hw_support": {}, \
+ "hw_mods": {} \
+ }'
+
+define Build/append-metadata-teltonika
+ echo $(call metadata_json_teltonika) | fwtool -I - $@
+endef
+
define Build/wrgg-pad-rootfs
$(STAGING_DIR_HOST)/bin/padjffs2 $(IMAGE_ROOTFS) -c 64 >>$@
endef
@@ -2527,6 +2557,23 @@ define Device/teltonika_rut230-v1
endef
TARGET_DEVICES += teltonika_rut230-v1
+define Device/teltonika_rut300
+ SOC := qca9531
+ DEVICE_VENDOR := Teltonika
+ DEVICE_MODEL := RUT300
+ SUPPORTED_TELTONIKA_DEVICES := teltonika,rut30x
+ DEVICE_PACKAGES := -kmod-ath9k -uboot-envtools -wpad-basic-wolfssl kmod-usb2
+ IMAGE_SIZE := 15552k
+ IMAGES += factory.bin
+ IMAGE/factory.bin = append-kernel | pad-to $$$$(BLOCKSIZE) | \
+ append-rootfs | pad-rootfs | append-metadata-teltonika | \
+ check-size $$$$(IMAGE_SIZE)
+ IMAGE/sysupgrade.bin = append-kernel | pad-to $$$$(BLOCKSIZE) | \
+ append-rootfs | pad-rootfs | append-metadata | \
+ check-size $$$$(IMAGE_SIZE)
+endef
+TARGET_DEVICES += teltonika_rut300
+
define Device/teltonika_rut955
SOC := ar9344
DEVICE_VENDOR := Teltonika
More information about the lede-commits
mailing list