[openwrt/openwrt] ipq40xx: add support for GL.iNet GL-A1300
LEDE Commits
lede-commits at lists.infradead.org
Wed Nov 9 14:53:33 PST 2022
hauke pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/9945d05171dd5f71c1d288ed63fa4112024d0a85
commit 9945d05171dd5f71c1d288ed63fa4112024d0a85
Author: Weiping Yang <weiping.yang at gl-inet.com>
AuthorDate: Mon Sep 19 05:47:40 2022 -0400
ipq40xx: add support for GL.iNet GL-A1300
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
FLASH1: 4 MiB NOR
FLASH2: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5G 802.11n/ac W2 2x2
USB: 1 x USB 3.0 port
Button: 1 x Reset button
Switch: 1 x Mode switch
LED: 1 x Blue LED + 1 x White LED
Install via uboot tftp or uboot web failsafe.
By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-a1300-squashfs-nand-factory.ubi
(IPQ40xx) # nand erase 0 0x8000000
(IPQ40xx) # nand write 0x84000000 0 $filesize
By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Weiping Yang <weiping.yang at gl-inet.com>
---
package/boot/uboot-envtools/files/ipq40xx | 1 +
package/firmware/ipq-wifi/Makefile | 2 +
.../ipq-wifi/board-glinet_gl-a1300.qca4019 | Bin 0 -> 24308 bytes
.../ipq40xx/base-files/etc/board.d/02_network | 1 +
.../ipq40xx/base-files/lib/upgrade/platform.sh | 1 +
.../arch/arm/boot/dts/qcom-ipq4018-gl-a1300.dts | 326 +++++++++++++++++++++
target/linux/ipq40xx/image/generic.mk | 14 +
7 files changed, 345 insertions(+)
diff --git a/package/boot/uboot-envtools/files/ipq40xx b/package/boot/uboot-envtools/files/ipq40xx
index 823a33ca1b..4ee83bb057 100644
--- a/package/boot/uboot-envtools/files/ipq40xx
+++ b/package/boot/uboot-envtools/files/ipq40xx
@@ -34,6 +34,7 @@ case "$board" in
alfa-network,ap120c-ac|\
devolo,magic-2-wifi-next|\
edgecore,ecw5211|\
+glinet,gl-a1300 |\
glinet,gl-ap1300|\
glinet,gl-b1300|\
glinet,gl-b2200|\
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile
index da82e16dde..2096b5f2d6 100644
--- a/package/firmware/ipq-wifi/Makefile
+++ b/package/firmware/ipq-wifi/Makefile
@@ -30,6 +30,7 @@ ALLWIFIBOARDS:= \
edgecore_ecw5410 \
edgecore_oap100 \
extreme-networks_ws-ap3915i \
+ glinet_gl-a1300 \
glinet_gl-ap1300 \
glinet_gl-s1300 \
linksys_ea8300 \
@@ -105,6 +106,7 @@ $(eval $(call generate-ipq-wifi-package,devolo_magic-2-wifi-next,devolo Magic 2
$(eval $(call generate-ipq-wifi-package,edgecore_ecw5410,Edgecore ECW5410))
$(eval $(call generate-ipq-wifi-package,edgecore_oap100,Edgecore OAP100))
$(eval $(call generate-ipq-wifi-package,extreme-networks_ws-ap3915i,Edgecore OAP100))
+$(eval $(call generate-ipq-wifi-package,glinet_gl-a1300,GL.iNet GL-A1300))
$(eval $(call generate-ipq-wifi-package,glinet_gl-ap1300,GL.iNet GL-AP1300))
$(eval $(call generate-ipq-wifi-package,glinet_gl-s1300,GL.iNet GL-S1300))
$(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
diff --git a/package/firmware/ipq-wifi/board-glinet_gl-a1300.qca4019 b/package/firmware/ipq-wifi/board-glinet_gl-a1300.qca4019
new file mode 100644
index 0000000000..d8695c9836
Binary files /dev/null and b/package/firmware/ipq-wifi/board-glinet_gl-a1300.qca4019 differ
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 2aef8d65dd..16b0f05a5b 100644
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -58,6 +58,7 @@ ipq40xx_setup_interfaces()
compex,wpj428)
ucidef_set_interface_lan "lan1 lan2"
;;
+ glinet,gl-a1300|\
glinet,gl-b1300|\
mobipromo,cm520-79f)
ucidef_set_interfaces_lan_wan "lan1 lan2" "wan"
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index 668ae04414..6b8f62d735 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -111,6 +111,7 @@ platform_do_upgrade() {
edgecore,ecw5211 |\
edgecore,oap100 |\
engenius,eap2200 |\
+ glinet,gl-a1300 |\
glinet,gl-ap1300 |\
luma,wrtq-329acn |\
mobipromo,cm520-79f |\
diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-gl-a1300.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-gl-a1300.dts
new file mode 100644
index 0000000000..5993243dc9
--- /dev/null
+++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-gl-a1300.dts
@@ -0,0 +1,326 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "GL.iNet GL-A1300";
+ compatible = "glinet,gl-a1300", "qcom,ipq4019";
+
+ aliases {
+ led-boot = &led_run;
+ led-failsafe = &led_run;
+ led-running = &led_run;
+ led-upgrade = &led_run;
+ label-mac-device = &swport4;
+ };
+
+ chosen {
+ bootargs-append = " ubi.mtd=ubi root=/dev/ubiblock0_1";
+ };
+
+ soc {
+ tcsr at 1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr at 194b000 {
+ /* select hostmode */
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ status = "okay";
+ };
+
+ ess_tcsr at 1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr at 1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ switch {
+ label = "switch-button";
+ gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_SETUP>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_run: blue {
+ label = "blue:status";
+ gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ white {
+ label = "white:status";
+ gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio_export {
+ compatible = "gpio-export";
+
+ usb {
+ gpio-export,name = "usb_power";
+ gpio-export,output = <1>;
+ gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&prng {
+ status = "okay";
+};
+
+&mdio {
+ status = "okay";
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+&crypto {
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ status = "okay";
+
+ pinctrl-0 = <&spi0_pins>;
+ pinctrl-names = "default";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, <&tlmm 5 GPIO_ACTIVE_HIGH>;
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+
+ partition at 60000 {
+ label = "QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+
+ partition at c0000 {
+ label = "CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+
+ partition at d0000 {
+ label = "DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+
+ partition at e0000 {
+ label = "APPSBLENV"; /* uboot env*/
+ reg = <0x000e0000 0x00010000>;
+ };
+
+ partition at f0000 {
+ label = "APPSBL"; /* uboot */
+ reg = <0x000f0000 0x00080000>;
+ read-only;
+ };
+
+ partition at 170000 {
+ label = "ART";
+ reg = <0x00170000 0x00010000>;
+ read-only;
+ compatible = "nvmem-cells";
+
+ precal_art_1000: precal at 1000 {
+ reg = <0x1000 0x2f20>;
+ };
+
+ precal_art_5000: precal at 5000 {
+ reg = <0x5000 0x2f20>;
+ };
+
+ macaddr_gmac0: macaddr at 0 {
+ reg = <0x0 0x6>;
+ };
+
+ macaddr_gmac1: macaddr at 6 {
+ reg = <0x6 0x6>;
+ };
+ };
+
+ partition at 180000 {
+ label = "log";
+ reg = <0x00180000 0x00020000>;
+ };
+ };
+ };
+
+ spi-nand at 1 {
+ compatible = "spi-nand";
+ reg = <1>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "ubi";
+ reg = <0x00000000 0x08000000>;
+ };
+ };
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ i2c_0_pins: i2c_0_pinmux {
+ pinmux {
+ pins = "gpio58", "gpio59";
+ function = "blsp_i2c0";
+ bias-disable;
+ };
+ };
+
+ spi0_pins: spi0_pinmux {
+ mux_spi {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ mux_cs {
+ function = "gpio";
+ pins = "gpio54", "gpio5";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&blsp1_i2c3 {
+ status = "okay";
+ pinctrl-0 = <&i2c_0_pins>;
+ pinctrl-names = "default";
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&usb3_ss_phy {
+ status = "okay";
+};
+
+&gmac {
+ status = "okay";
+};
+
+&switch {
+ status = "okay";
+};
+
+&swport3 {
+ status = "okay";
+
+ label = "lan2";
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&macaddr_gmac0>;
+ mac-address-increment = <2>;
+};
+
+&swport4 {
+ status = "okay";
+
+ label = "lan1";
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&macaddr_gmac0>;
+};
+
+&swport5 {
+ status = "okay";
+
+ nvmem-cell-names = "mac-address";
+ nvmem-cells = <&macaddr_gmac1>;
+};
+
+&wifi0 {
+ status = "okay";
+ nvmem-cell-names = "pre-calibration";
+ nvmem-cells = <&precal_art_1000>;
+ qcom,ath10k-calibration-variant = "GL-A1300";
+};
+
+&wifi1 {
+ status = "okay";
+ nvmem-cell-names = "pre-calibration";
+ nvmem-cells = <&precal_art_5000>;
+ qcom,ath10k-calibration-variant = "GL-A1300";
+};
diff --git a/target/linux/ipq40xx/image/generic.mk b/target/linux/ipq40xx/image/generic.mk
index e8e6e29e72..b50d072bec 100644
--- a/target/linux/ipq40xx/image/generic.mk
+++ b/target/linux/ipq40xx/image/generic.mk
@@ -565,6 +565,20 @@ endef
# Missing DSA Setup
#TARGET_DEVICES += ezviz_cs-w3-wd1200g-eup
+define Device/glinet_gl-a1300
+ $(call Device/FitImage)
+ $(call Device/UbiFit)
+ DEVICE_VENDOR := GL.iNet
+ DEVICE_MODEL := GL-A1300
+ SOC := qcom-ipq4018
+ DEVICE_DTS_CONFIG := config at ap.dk01.1-c2
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ IMAGE_SIZE := 131072k
+ DEVICE_PACKAGE := ipq-wifi-glinet_gl-a1300
+endef
+TARGET_DEVICES += glinet_gl-a1300
+
define Device/glinet_gl-ap1300
$(call Device/FitImage)
$(call Device/UbiFit)
More information about the lede-commits
mailing list