[openwrt/openwrt] ramips: add support for TP-Link MR600 V2(EU)
LEDE Commits
lede-commits at lists.infradead.org
Sat Nov 5 15:58:09 PDT 2022
hauke pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/78110c3b5fce119d13cd45dadd33ca396c8ce197
commit 78110c3b5fce119d13cd45dadd33ca396c8ce197
Author: Linos Giannopoulos <linosgian00 at gmail.com>
AuthorDate: Mon Oct 3 01:30:28 2022 +0300
ramips: add support for TP-Link MR600 V2(EU)
MR600 V2(EU) is an LTE router that also supports 4G+ band aggregation
etc. and can reportedly achieve higher bandwidth with it.
- Specifications:
* SoC: Mediatek MT7621DAT 880MHz
* RAM: 128MB DDR3
* Flash: 16MB SPI NOR flash (GD25Q128C)
* LTE Modem: Qualcomm MDM9240
* WiFi 5GHz: Mediatek MT7613BEN
* WiFi 2.4GHz: Mediatek MT7603EN
* Ethernet: MT7530, 4x 1000Base-T.
* UART: Serial console (115200 8n1), J1(GND:3)
* Buttons: Reset, WPS.
* LED: Power, WAN, LTE, WiFi 2GHz and 5GHz, LAN, Signal1, Signal2,
Signal3
- MAC Addresses:
OEM firmware configuration:
54:af:97:xx:xx:7b : 2.4G
54:af:97:xx:xx:7a : 5G
54:af:97:xx:xx:7c : LTE
54:af:97:xx:xx:7b : LAN (label)
54:af:97:xx:xx:7c : WAN
- Installation:
1. Download the OpenWrt initramfs-image.
Place it into a TFTP server root directory and rename it to openwrt.img
Configure the TFTP server to listen at 192.168.0.5/24.
3. Connect to the serial console.
Attach power and interrupt the boot procedure when prompted (type `tpl`).
Credentials are admin / 1234
4. Configure U-Boot for booting OpenWrt from ram
$ tftpboot
$ bootm
5. Transfer the OpenWrt sysupgrade image to the device.
- LTE:
In order to setup the wwan0 interface:
1. Add a `qmi` proto interface under `/etc/config/network`, e.g.:
```
config interface 'wwan0'
option device '/dev/cdc-wdm0'
option proto 'qmi'
option pincode 'XXXX'
option apn 'your_isp_apn'
```
2. Add `wwan0` interface to the `wan` firewall zone
3. `/etc/init.d/network restart`
Signed-off-by: Linos Giannopoulos <linosgian00 at gmail.com>
---
.../linux/ramips/dts/mt7621_tplink_mr600-v2-eu.dts | 207 +++++++++++++++++++++
target/linux/ramips/image/mt7621.mk | 15 ++
.../ramips/mt7621/base-files/etc/board.d/01_leds | 5 +
.../mt7621/base-files/etc/board.d/02_network | 8 +
4 files changed, 235 insertions(+)
diff --git a/target/linux/ramips/dts/mt7621_tplink_mr600-v2-eu.dts b/target/linux/ramips/dts/mt7621_tplink_mr600-v2-eu.dts
new file mode 100644
index 0000000000..b7475ec15b
--- /dev/null
+++ b/target/linux/ramips/dts/mt7621_tplink_mr600-v2-eu.dts
@@ -0,0 +1,207 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ compatible = "tplink,mr600-v2-eu", "mediatek,mt7621-soc";
+ model = "TP-Link MR600 v2 (EU)";
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ label-mac-device = &gmac0;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ wlan {
+ label = "wlan";
+ gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WLAN>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "white:power";
+ gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+ };
+ wlan {
+ label = "white:wlan";
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+ wan {
+ label = "white:wan";
+ gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+ };
+
+ signal1 {
+ label = "white:signal1";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ };
+
+ signal2 {
+ label = "white:signal2";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ };
+
+ signal3 {
+ label = "white:signal3";
+ gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
+ };
+
+ 4g {
+ label = "white:4g";
+ gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+ };
+ lan {
+ label = "white:lan";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+};
+
+&spi0 {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <80000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "uboot";
+ reg = <0x00000 0x20000>;
+ read-only;
+ };
+
+ partition at 20000 {
+ compatible = "openwrt,uimage";
+ openwrt,offset = <512>; /* account for the 512-byte long header */
+ label = "firmware";
+ reg = <0x20000 0xfa0000>;
+ };
+
+ romfile: partition at fc0000 {
+ label = "romfile";
+ reg = <0xfc0000 0x10000>;
+ read-only;
+ };
+
+ partition at fd0000 {
+ label = "config";
+ reg = <0xfd0000 0x10000>;
+ read-only;
+ };
+
+ radio: partition at fe0000 {
+ label = "radio";
+ reg = <0xfe0000 0x10000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+
+&pcie0 {
+ mt76 at 0,0 {
+ compatible = "mediatek,mt76";
+ reg = <0x0000 0 0 0 0>;
+ nvmem-cells = <&macaddr_romfile_f100>;
+ nvmem-cell-names = "mac-address";
+ mediatek,mtd-eeprom = <&radio 0x0>;
+ mtd-mac-address = <&romfile 0xf100>;
+ ieee80211-freq-limit = <2400000 2500000>;
+ };
+};
+
+&pcie1 {
+ mt76 at 0,0 {
+ compatible = "mediatek,mt76";
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&radio 0x8000>;
+ ieee80211-freq-limit = <5000000 6000000>;
+ nvmem-cells = <&macaddr_romfile_f100>;
+ nvmem-cell-names = "mac-address";
+ mac-address-increment = <(-1)>;
+ };
+};
+
+&gmac0 {
+ nvmem-cells = <&macaddr_romfile_f100>;
+ nvmem-cell-names = "mac-address";
+};
+
+&gmac1 {
+ status = "okay";
+ label = "wan";
+ phy-handle = <ðphy4>;
+
+ nvmem-cells = <&macaddr_romfile_f100>;
+ nvmem-cell-names = "mac-address";
+};
+
+&mdio {
+ ethphy4: ethernet-phy at 4 {
+ reg = <4>;
+ };
+};
+
+
+&switch0 {
+ ports {
+ port at 1 {
+ status = "okay";
+ label = "lan1";
+ };
+ port at 2 {
+ status = "okay";
+ label = "lan2";
+ };
+ port at 3 {
+ status = "okay";
+ label = "lan3";
+ };
+ };
+};
+
+&romfile {
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_romfile_f100: romfile at f100 {
+ reg = <0xf100 0x6>;
+ };
+};
diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk
index 60f927eeed..35817d0317 100644
--- a/target/linux/ramips/image/mt7621.mk
+++ b/target/linux/ramips/image/mt7621.mk
@@ -1910,6 +1910,21 @@ define Device/tplink_eap615-wall-v1
endef
TARGET_DEVICES += tplink_eap615-wall-v1
+define Device/tplink_mr600-v2-eu
+ $(Device/dsa-migration)
+ $(Device/tplink-v2)
+ DEVICE_MODEL := MR600
+ DEVICE_VARIANT := v2 (EU)
+ TPLINK_FLASHLAYOUT := 16Mltq
+ DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap \
+ kmod-usb-net-qmi-wwan uqmi kmod-usb3
+ KERNEL := $(KERNEL_DTB) | uImage lzma
+ KERNEL_INITRAMFS := $$(KERNEL) | tplink-v2-header
+ TPLINK_BOARD_ID := MR600-V2-EU
+ IMAGE_SIZE := 16384k
+endef
+TARGET_DEVICES += tplink_mr600-v2-eu
+
define Device/tplink_re350-v1
$(Device/dsa-migration)
$(Device/tplink-safeloader)
diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
index c2bc9c3774..9cf83c357c 100644
--- a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
@@ -147,6 +147,11 @@ tplink,re350-v1)
ucidef_set_led_netdev "eth_act" "LAN act" "green:eth_act" "lan" "tx rx"
ucidef_set_led_netdev "eth_link" "LAN link" "green:eth_link" "lan" "link"
;;
+tplink,mr600-v2-eu)
+ ucidef_set_led_netdev "lan" "LAN" "white:lan" "br-lan"
+ ucidef_set_led_netdev "wan" "WAN" "white:wan" "wan"
+ ucidef_set_led_netdev "4g" "4G" "white:4g" "wwan0"
+ ;;
tplink,re500-v1|\
tplink,re650-v1|\
tplink,re650-v2)
diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network
index 14250aa150..bfc654a23a 100644
--- a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network
@@ -100,6 +100,9 @@ ramips_setup_interfaces()
tplink,tl-wpa8631p-v3)
ucidef_set_interface_lan "lan1 lan2 lan3 plc0"
;;
+ tplink,mr600-v2-eu)
+ ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan"
+ ;;
ubnt,edgerouter-x)
ucidef_set_interfaces_lan_wan "eth1 eth2 eth3 eth4" "eth0"
;;
@@ -216,6 +219,11 @@ ramips_setup_macs()
wan_mac=$(mtd_get_mac_ascii Config wan_hwaddr)
label_mac=$lan_mac
;;
+ tplink,mr600-v2-eu)
+ label_mac=$(cat "/sys/class/net/eth0/address")
+ wwan_mac=$(macaddr_add $label_mac 1)
+ ucidef_set_interface "wwan0" device "/dev/cdc-wdm0" protocol "qmi" macaddr "$wwan_mac"
+ ;;
mikrotik,routerboard-750gr3|\
mikrotik,routerboard-760igs|\
mikrotik,routerboard-m11g|\
More information about the lede-commits
mailing list