[openwrt/openwrt] mediatek: mt7622: add support for ELECOM WRC-X3200GST3
LEDE Commits
lede-commits at lists.infradead.org
Sat May 21 14:27:19 PDT 2022
dangole pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/58b3b557b629f6a2046414e0e1b39189d918133f
commit 58b3b557b629f6a2046414e0e1b39189d918133f
Author: INAGAKI Hiroshi <musashino.open at gmail.com>
AuthorDate: Fri Apr 23 18:32:11 2021 +0900
mediatek: mt7622: add support for ELECOM WRC-X3200GST3
ELECOM WRC-X3200GST3 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
MT7622B.
Specifications:
- SoC : MediaTek MT7622B
- RAM : DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
- Flash : SPI-NAND 128 MiB (Winbond W25N01GVZEIG)
- WLAN : 2.4/5 GHz 4T4R
- 2.4 GHz : MediaTek MT7622B (SoC)
- 5 GHz : MediaTek MT7915A
- Ethernet : 5x 10/100/1000 Mbps
- Switch : MediaTek MT7531
- LEDs/Keys : 6x/4x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- J19: 3.3V, GND, TX, RX from power jack side
- 115200n8
- Power : 12 VDC, 1.5 A
Flash instruction using factory image:
1. Boot WRC-X3200GST3 normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing
MAC Addresses:
LAN : 04:AB:18:xx:xx:77 (Factory, 0x7FFF4 (hex))
WAN : 04:AB:18:xx:xx:78 (Factory, 0x7FFFA (hex))
2.4 GHz: 04:AB:18:xx:xx:79 (Factory, 0x4 (hex))
5 GHz : 04:AB:18:xx:xx:7A (none)
Note:
- currently, there is no "phy1tpt" trigger for 5 GHz wlan (MT7915) in
"trigger" file of LEDs, use "phy1radio" trigger instead
Signed-off-by: INAGAKI Hiroshi <musashino.open at gmail.com>
---
.../mediatek/dts/mt7622-elecom-wrc-x3200gst3.dts | 436 +++++++++++++++++++++
target/linux/mediatek/image/mt7622.mk | 20 +
.../mt7622/base-files/etc/board.d/02_network | 1 +
.../mt7622/base-files/lib/upgrade/platform.sh | 12 +-
4 files changed, 464 insertions(+), 5 deletions(-)
diff --git a/target/linux/mediatek/dts/mt7622-elecom-wrc-x3200gst3.dts b/target/linux/mediatek/dts/mt7622-elecom-wrc-x3200gst3.dts
new file mode 100644
index 0000000000..fdbcbc18bc
--- /dev/null
+++ b/target/linux/mediatek/dts/mt7622-elecom-wrc-x3200gst3.dts
@@ -0,0 +1,436 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+#include "mt7622.dtsi"
+#include "mt6380.dtsi"
+
+/ {
+ model = "ELECOM WRC-X3200GST3";
+ compatible = "elecom,wrc-x3200gst3", "mediatek,mt7622";
+
+ aliases {
+ serial0 = &uart0;
+ led-boot = &led_power_green;
+ led-failsafe = &led_power_red;
+ led-running = &led_power_green;
+ led-upgrade = &led_power_green;
+ label-mac-device = &wan;
+ };
+
+ chosen {
+ bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n8 swiotlb=512";
+ };
+
+ memory {
+ reg = <0 0x40000000 0 0x1f000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ label = "red:wps";
+ gpios = <&pio 47 GPIO_ACTIVE_HIGH>;
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_WPS;
+ };
+
+ led_power_red: led-1 {
+ label = "red:power";
+ gpios = <&pio 48 GPIO_ACTIVE_HIGH>;
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_POWER;
+ function-enumerator = <1>;
+ };
+
+ led_power_green: led-2 {
+ label = "green:power";
+ gpios = <&pio 49 GPIO_ACTIVE_HIGH>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_POWER;
+ function-enumerator = <2>;
+ };
+
+ led-3 {
+ label = "blue:power";
+ gpios = <&pio 50 GPIO_ACTIVE_HIGH>;
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_POWER;
+ function-enumerator = <3>;
+ };
+
+ led-4 {
+ label = "white:wlan2g";
+ gpios = <&pio 85 GPIO_ACTIVE_HIGH>;
+ color = <LED_COLOR_ID_WHITE>;
+ function = LED_FUNCTION_WLAN;
+ function-enumerator = <1>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ led-5 {
+ label = "white:wlan5g";
+ gpios = <&pio 89 GPIO_ACTIVE_HIGH>;
+ color = <LED_COLOR_ID_WHITE>;
+ function = LED_FUNCTION_WLAN;
+ function-enumerator = <2>;
+ linux,default-trigger = "phy1radio";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&pio 0 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ ap {
+ label = "ap";
+ gpios = <&pio 42 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_0>;
+ linux,input-type = <EV_SW>;
+ };
+
+ router {
+ label = "router";
+ gpios = <&pio 43 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_1>;
+ linux,input-type = <EV_SW>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&pio 102 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+};
+
+&cpu0 {
+ proc-supply = <&mt6380_vcpu_reg>;
+ sram-supply = <&mt6380_vm_reg>;
+};
+
+&cpu1 {
+ proc-supply = <&mt6380_vcpu_reg>;
+ sram-supply = <&mt6380_vm_reg>;
+};
+
+&pio {
+ eth_pins: eth-pins {
+ mux {
+ function = "eth";
+ groups = "mdc_mdio", "rgmii_via_gmac2";
+ };
+ };
+
+ pcie0_pins: pcie0-pins {
+ mux {
+ function = "pcie";
+ groups = "pcie0_pad_perst",
+ "pcie0_1_waken",
+ "pcie0_1_clkreq";
+ };
+ };
+
+ pmic_bus_pins: pmic-bus-pins {
+ mux {
+ function = "pmic";
+ groups = "pmic_bus";
+ };
+ };
+
+ pwm7_pins: pwm1-2-pins {
+ mux {
+ function = "pwm";
+ groups = "pwm_ch7_2";
+ };
+ };
+
+ /* Serial NAND is shared pin with SPI-NOR */
+ serial_nand_pins: serial-nand-pins {
+ mux {
+ function = "flash";
+ groups = "snfi";
+ };
+
+ conf-cmd-data {
+ pins = "SPI_WP", "SPI_HOLD", "SPI_MOSI",
+ "SPI_MISO", "SPI_CS";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+
+ conf-clk {
+ pins = "SPI_CLK";
+ drive-strength = <16>;
+ bias-pull-down;
+ };
+ };
+
+ uart0_pins: uart0-pins {
+ mux {
+ function = "uart";
+ groups = "uart0_0_tx_rx" ;
+ };
+ };
+
+ watchdog_pins: watchdog-pins {
+ mux {
+ function = "watchdog";
+ groups = "watchdog";
+ };
+ };
+};
+
+ð {
+ pinctrl-names = "default";
+ pinctrl-0 = <ð_pins>;
+ status = "okay";
+
+ gmac0: mac at 0 {
+ compatible = "mediatek,eth-mac";
+ reg = <0>;
+
+ phy-connection-type = "2500base-x";
+
+ nvmem-cells = <&macaddr_factory_7fff4>;
+ nvmem-cell-names = "mac-address";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+
+ mdio-bus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch at 0 {
+ compatible = "mediatek,mt7531";
+ reg = <0>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ interrupt-parent = <&pio>;
+ interrupts = <53 IRQ_TYPE_LEVEL_HIGH>;
+ reset-gpios = <&pio 54 GPIO_ACTIVE_HIGH>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ wan: port at 0 {
+ reg = <0>;
+ label = "wan";
+
+ nvmem-cells = <&macaddr_factory_7fffa>;
+ nvmem-cell-names = "mac-address";
+ };
+
+ port at 1 {
+ reg = <1>;
+ label = "lan4";
+ };
+
+ port at 2 {
+ reg = <2>;
+ label = "lan3";
+ };
+
+ port at 3 {
+ reg = <3>;
+ label = "lan2";
+ };
+
+ port at 4 {
+ reg = <4>;
+ label = "lan1";
+ };
+
+ port at 6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "2500base-x";
+
+ fixed-link {
+ speed = <2500>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+ };
+ };
+};
+
+&bch {
+ status = "okay";
+};
+
+&snfi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&serial_nand_pins>;
+ status = "okay";
+
+ flash at 0 {
+ compatible = "spi-nand";
+ reg = <0>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+ nand-ecc-engine = <&snfi>;
+ mediatek,bmt-v2;
+ mediatek,bmt-table-size = <0x1000>;
+ mediatek,bmt-remap-range = <0x0 0x8c0000>,
+ <0x1bc0000 0x30c0000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "Preloader";
+ reg = <0x0 0x80000>;
+ read-only;
+ };
+
+ partition at 80000 {
+ label = "ATF";
+ reg = <0x80000 0x40000>;
+ read-only;
+ };
+
+ partition at c0000 {
+ label = "u-boot";
+ reg = <0xc0000 0x80000>;
+ read-only;
+ };
+
+ partition at 140000 {
+ label = "u-boot-env";
+ reg = <0x140000 0x80000>;
+ read-only;
+ };
+
+ factory: partition at 1c0000 {
+ label = "factory";
+ reg = <0x1c0000 0x100000>;
+ read-only;
+
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_factory_4: macaddr at 4 {
+ reg = <0x4 0x6>;
+ };
+
+ macaddr_factory_7fff4: macaddr at 7fff4 {
+ reg = <0x7fff4 0x6>;
+ };
+
+ macaddr_factory_7fffa: macaddr at 7fffa {
+ reg = <0x7fffa 0x6>;
+ };
+ };
+
+ partition at 2c0000 {
+ label = "kernel";
+ reg = <0x2c0000 0x600000>;
+ };
+
+ partition at 8c0000 {
+ label = "ubi";
+ reg = <0x8c0000 0x1300000>;
+ };
+
+ partition at 1bc0000 {
+ label = "tm_pattern";
+ reg = <0x1bc0000 0x500000>;
+ read-only;
+ };
+
+ partition at 20c0000 {
+ label = "tm_key";
+ reg = <0x20c0000 0x100000>;
+ read-only;
+ };
+
+ partition at 21c0000 {
+ label = "user_data";
+ reg = <0x21c0000 0xf00000>;
+ read-only;
+ };
+
+ partition at 30c0000 {
+ label = "reserved";
+ reg = <0x30c0000 0x4f40000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&pcie0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie0_pins>;
+ status = "okay";
+};
+
+&slot0 {
+ status = "okay";
+
+ wifi at 0,0 {
+ compatible = "mediatek,mt76";
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x5000>;
+ ieee80211-freq-limit = <5000000 6000000>;
+ nvmem-cells = <&macaddr_factory_4>;
+ nvmem-cell-names = "mac-address";
+ mac-address-increment = <1>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm7_pins>;
+ status = "okay";
+};
+
+&pwrap {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_bus_pins>;
+ status = "okay";
+};
+
+&rtc {
+ status = "disabled";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+ status = "okay";
+};
+
+&watchdog {
+ pinctrl-names = "default";
+ pinctrl-0 = <&watchdog_pins>;
+ status = "okay";
+};
+
+&wmac {
+ status = "okay";
+
+ mediatek,mtd-eeprom = <&factory 0x0>;
+};
diff --git a/target/linux/mediatek/image/mt7622.mk b/target/linux/mediatek/image/mt7622.mk
index 39bc7bc2ea..aba8bdfe0b 100644
--- a/target/linux/mediatek/image/mt7622.mk
+++ b/target/linux/mediatek/image/mt7622.mk
@@ -137,6 +137,26 @@ define Device/elecom_wrc-2533gent
endef
TARGET_DEVICES += elecom_wrc-2533gent
+define Device/elecom_wrc-x3200gst3
+ DEVICE_VENDOR := ELECOM
+ DEVICE_MODEL := WRC-X3200GST3
+ DEVICE_DTS := mt7622-elecom-wrc-x3200gst3
+ DEVICE_DTS_DIR := ../dts
+ IMAGE_SIZE := 25600k
+ KERNEL_SIZE := 6144k
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ UBINIZE_OPTS := -E 5
+ IMAGES += factory.bin
+ IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | \
+ append-ubi | check-size | \
+ elecom-wrc-gs-factory WRC-X3200GST3 0.00 -N | \
+ append-string MT7622_ELECOM_WRC-X3200GST3
+ IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+ DEVICE_PACKAGES := kmod-mt7915e
+endef
+TARGET_DEVICES += elecom_wrc-x3200gst3
+
define Device/linksys_e8450
DEVICE_VENDOR := Linksys
DEVICE_MODEL := E8450
diff --git a/target/linux/mediatek/mt7622/base-files/etc/board.d/02_network b/target/linux/mediatek/mt7622/base-files/etc/board.d/02_network
index c55fcbee2e..29f4b875f8 100644
--- a/target/linux/mediatek/mt7622/base-files/etc/board.d/02_network
+++ b/target/linux/mediatek/mt7622/base-files/etc/board.d/02_network
@@ -9,6 +9,7 @@ mediatek_setup_interfaces()
case $board in
bananapi,bpi-r64|\
+ elecom,wrc-x3200gst3|\
linksys,e8450|\
linksys,e8450-ubi|\
mediatek,mt7622-rfb1|\
diff --git a/target/linux/mediatek/mt7622/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/mt7622/base-files/lib/upgrade/platform.sh
index f54665dfa1..1036793145 100755
--- a/target/linux/mediatek/mt7622/base-files/lib/upgrade/platform.sh
+++ b/target/linux/mediatek/mt7622/base-files/lib/upgrade/platform.sh
@@ -32,6 +32,12 @@ platform_do_upgrade() {
nand_do_upgrade "$1"
fi
;;
+ elecom,wrc-x3200gst3|\
+ mediatek,mt7622-rfb1-ubi|\
+ totolink,a8000ru|\
+ xiaomi,redmi-router-ax6s)
+ nand_do_upgrade "$1"
+ ;;
linksys,e8450-ubi)
CI_KERNPART="fit"
nand_do_upgrade "$1"
@@ -44,11 +50,6 @@ platform_do_upgrade() {
fi
default_do_upgrade "$1"
;;
- mediatek,mt7622-rfb1-ubi|\
- totolink,a8000ru|\
- xiaomi,redmi-router-ax6s)
- nand_do_upgrade "$1"
- ;;
*)
default_do_upgrade "$1"
;;
@@ -67,6 +68,7 @@ platform_check_image() {
buffalo,wsr-2533dhp2)
buffalo_check_image "$board" "$magic" "$1" || return 1
;;
+ elecom,wrc-x3200gst3|\
mediatek,mt7622-rfb1-ubi|\
totolink,a8000ru|\
xiaomi,redmi-router-ax6s)
More information about the lede-commits
mailing list