[openwrt/openwrt] realtek: add support for Panasonic Switch-M8eG PN28080K
LEDE Commits
lede-commits at lists.infradead.org
Sun Mar 13 12:53:45 PDT 2022
hauke pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/e83ab243bef6e32c1fbb8ceda5301aa21f0c51cf
commit e83ab243bef6e32c1fbb8ceda5301aa21f0c51cf
Author: INAGAKI Hiroshi <musashino.open at gmail.com>
AuthorDate: Wed Mar 9 23:31:00 2022 +0900
realtek: add support for Panasonic Switch-M8eG PN28080K
Panasonic Switch-M8eG PN28080K is a 8 + 1 port gigabit switch, based on
RTL8380M.
Specification:
- SoC : Realtek RTL8380M
- RAM : DDR3 128 MiB (Winbond W631GG8KB-15)
- Flash : SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G)
- Ethernet : 10/100/1000 Mbps x8 + 1
- port 1-8 : TP, RTL8218B (SoC)
- port 9 : SFP, RTL8380M (SoC)
- LEDs/Keys : 7x / 1x
- UART : RS-232 port on the front panel (connector: RJ-45)
- 3:TX, 4:GND, 5:GND, 6:RX (pin number: RJ-45)
- 9600n8
- Power : 100-240 VAC, 50/60 Hz, 0.5 A
- Plug : IEC 60320-C13
- Stock OS : VxWorks based
Flash instruction using initramfs image:
1. Prepare the TFTP server with the IP address 192.168.1.111
2. Rename the OpenWrt initramfs image to "0101A8C0.img" and place it to
the TFTP directory
3. Download the official upgrading firmware (ex: pn28080k_v30000.rom)
and place it to the TFTP directory
4. Boot M8eG and interrupt the U-Boot with Ctrl + C keys
5. Execute the following commands and boot with the OpenWrt initramfs
image
rtk network on
tftpboot 0x81000000
bootm
6. Backup mtdblock files to the computer by scp or anything and reboot
7. Interrupt the U-Boot and execute the following commands to re-create
filesystem in the flash
ffsmount c:/
ffsfmt c:/
this step takes a long time, about ~ 4 mins
8. Execute the following commands to put the official images to the
filesystem
updatert <official image>
example:
updatert pn28080k_v30000.rom
this step takes about ~ 40 secs
9. Set the environment variables of the U-Boot by the following commands
setenv loadaddr 0xb4e00000
setenv bootcmd bootm
saveenv
10: Download the OpenWrt initramfs image and boot with it
tftpboot 0x81000000 0101A8C0.img
bootm
11: On the initramfs image, download the sysupgrade image and perform
sysupgrade with it
sysupgrade <imagename>
12: Wait ~ 120 seconds to complete flashing
Note:
- "Switch-M8eG" is a model name, and "PN28080K" is a model number.
Switch-M8eG has an another (old) model number ("PN28080"), it's not a
Realtek based hardware.
- Switch-M8eG has a "POWER" LED (Green), but it's not connected to any
GPIO pin.
- The U-Boot checks the runtime images in the flash when booting and
fails to execute anything in "bootcmd" variable if the images are not
exsisting.
- A filesystem is formed in the flash (0x100000-0x1DFFFFF) on the stock
firmware and it includes the stock images, configuration files and
checksum files. It's unknown format, can't be managed on the OpenWrt.
To get the enough space for OpenWrt, move the filesystem to the head
of "fs_reserved" partition by execution of "ffsfmt" and "updatert".
- On the other devices in the same series of Switch-M8eG PN28080K, the
INT pin on the PCA9555 is not connected to anywhere.
Back to the stock firmware:
1. Delete "loadaddr" variable and set "bootcmd" to the original value
on U-Boot:
setenv loadaddr
setenv bootcmd 'bootm 0x81000000'
on OpenWrt:
fw_setenv loadaddr
fw_setenv bootcmd 'bootm 0x81000000'
2. Perform reset or reboot
on U-Boot:
reset
on OpenWrt:
reboot
Signed-off-by: INAGAKI Hiroshi <musashino.open at gmail.com>
Reviewed-by: Sander Vanheule <sander at svanheule.net>
---
.../dts-5.10/rtl8380_panasonic_m8eg-pn28080k.dts | 133 ++++++++++++++
.../dts-5.10/rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi | 195 +++++++++++++++++++++
target/linux/realtek/image/rtl838x.mk | 10 ++
3 files changed, 338 insertions(+)
diff --git a/target/linux/realtek/dts-5.10/rtl8380_panasonic_m8eg-pn28080k.dts b/target/linux/realtek/dts-5.10/rtl8380_panasonic_m8eg-pn28080k.dts
new file mode 100644
index 0000000000..f9d58f5b66
--- /dev/null
+++ b/target/linux/realtek/dts-5.10/rtl8380_panasonic_m8eg-pn28080k.dts
@@ -0,0 +1,133 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "rtl838x.dtsi"
+#include "rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi"
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ compatible = "panasonic,m8eg-pn28080k", "realtek,rtl8380-soc";
+ model = "Panasonic Switch-M8eG PN28080K";
+
+ aliases {
+ led-boot = &led_status_eco_green;
+ led-failsafe = &led_status_eco_amber;
+ led-running = &led_status_eco_green;
+ led-upgrade = &led_status_eco_green;
+ };
+
+ sfp0: sfp-p9 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c0>;
+ tx-fault-gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+ tx-disable-gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+ los-gpio = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&leds {
+ led_status_eco_amber: led-5 {
+ label = "amber:status_eco";
+ gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_AMBER>;
+ function = LED_FUNCTION_STATUS;
+ function-enumerator = <1>;
+ };
+
+ led_status_eco_green: led-6 {
+ label = "green:status_eco";
+ gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ function-enumerator = <2>;
+ };
+};
+
+&i2c_gpio_0 {
+ scl-gpios = <&gpio0 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+};
+
+&i2c_gpio_1 {
+ scl-gpios = <&gpio0 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio0 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+};
+
+&gpio1 {
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+};
+
+&gpio2 {
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+};
+
+&i2c_switch {
+ i2c0: i2c at 0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ };
+};
+
+ðernet0 {
+ mdio-bus {
+ compatible = "realtek,rtl838x-mdio";
+ regmap = <ðernet0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ INTERNAL_PHY(8)
+ INTERNAL_PHY(9)
+ INTERNAL_PHY(10)
+ INTERNAL_PHY(11)
+ INTERNAL_PHY(12)
+ INTERNAL_PHY(13)
+ INTERNAL_PHY(14)
+ INTERNAL_PHY(15)
+
+ INTERNAL_PHY(24)
+ };
+};
+
+&switch0 {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ SWITCH_PORT(8, 1, internal)
+ SWITCH_PORT(9, 2, internal)
+ SWITCH_PORT(10, 3, internal)
+ SWITCH_PORT(11, 4, internal)
+ SWITCH_PORT(12, 5, internal)
+ SWITCH_PORT(13, 6, internal)
+ SWITCH_PORT(14, 7, internal)
+ SWITCH_PORT(15, 8, internal)
+
+ port at 24 {
+ reg = <24>;
+ label = "lan9";
+ phy-mode = "1000base-x";
+ phy-handle = <&phy24>;
+ managed = "in-band-status";
+ sfp = <&sfp0>;
+ };
+
+ port at 28 {
+ ethernet = <ðernet0>;
+ reg = <28>;
+ phy-mode = "internal";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+};
diff --git a/target/linux/realtek/dts-5.10/rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi b/target/linux/realtek/dts-5.10/rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi
new file mode 100644
index 0000000000..48aa1849d6
--- /dev/null
+++ b/target/linux/realtek/dts-5.10/rtl83xx_panasonic_mxxeg-pn28xx0k.dtsi
@@ -0,0 +1,195 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ chosen {
+ bootargs = "console=ttyS0,9600";
+ };
+
+ memory at 0 {
+ device_type = "memory";
+ reg = <0x0 0x8000000>;
+ };
+
+ leds: leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ label = "amber:any_col";
+ gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_AMBER>;
+ function = LED_FUNCTION_FAULT;
+ };
+
+ led-1 {
+ label = "green:giga";
+ gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_INDICATOR;
+ function-enumerator = <1>;
+ };
+
+ led-2 {
+ label = "green:100m";
+ gpios = <&gpio2 9 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_INDICATOR;
+ function-enumerator = <2>;
+ };
+
+ led-3 {
+ label = "green:full";
+ gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_INDICATOR;
+ function-enumerator = <3>;
+ };
+
+ led-4 {
+ label = "green:loop_history";
+ gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_INDICATOR;
+ function-enumerator = <4>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ led_mode {
+ label = "led-mode";
+ gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_0>;
+ };
+ };
+
+ gpio-restart {
+ compatible = "gpio-restart";
+ gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ i2c_gpio_0: i2c-gpio-0 {
+ compatible = "i2c-gpio";
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio1: gpio at 20 {
+ compatible = "nxp,pca9555";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpio2: gpio at 75 {
+ compatible = "nxp,pca9539";
+ reg = <0x75>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ /*
+ * GPIO14 (IO1_6): Shift Register RESET (port LED)
+ * - Switch-M8eG PN28080K: 3x 74HC164
+ * - Switch-M24eG PN28240K: 6x 74HC164
+ * - Switch-M48eG PN28480K: 12x 74HC164
+ */
+ portled_sregister_reset {
+ gpio-hog;
+ gpios = <14 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "portled-sregister-reset";
+ };
+ };
+ };
+
+ i2c_gpio_1: i2c-gpio-1 {
+ compatible = "i2c-gpio";
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c_switch: i2c-switch at 70 {
+ compatible = "nxp,pca9545";
+ reset-gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x0 0x80000>;
+ read-only;
+ };
+
+ partition at 80000 {
+ label = "u-boot-env";
+ reg = <0x80000 0x10000>;
+ };
+
+ partition at 90000 {
+ label = "u-boot-env2";
+ reg = <0x90000 0x10000>;
+ };
+
+ partition at a0000 {
+ label = "sysinfo";
+ reg = <0xa0000 0x60000>;
+ read-only;
+ };
+
+ /*
+ * Filesystem area in stock firmware
+ * (0x100000-0x1DFFFFF)
+ *
+ * stock firmware images are required to pass
+ * the checking by the U-Boot, also for OpenWrt
+ *
+ * in OpenWrt:
+ * - 0x100000-0xDFFFFF (13M): stock images
+ * - 0xE00000-0x1DFFFFF(16M): OpenWrt image
+ */
+ partition at 100000 {
+ label = "fs_reserved";
+ reg = <0x100000 0xd00000>;
+ };
+
+ partition at e00000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0xe00000 0x1000000>;
+ };
+
+ partition at 1e00000 {
+ label = "vlog_data";
+ reg = <0x1e00000 0x100000>;
+ read-only;
+ };
+
+ partition at 1f00000 {
+ label = "elog_data";
+ reg = <0x1f00000 0x100000>;
+ read-only;
+ };
+ };
+ };
+};
diff --git a/target/linux/realtek/image/rtl838x.mk b/target/linux/realtek/image/rtl838x.mk
index b9259401b2..9688dd93de 100644
--- a/target/linux/realtek/image/rtl838x.mk
+++ b/target/linux/realtek/image/rtl838x.mk
@@ -85,6 +85,16 @@ define Device/netgear_gs310tp-v1
endef
TARGET_DEVICES += netgear_gs310tp-v1
+define Device/panasonic_m8eg-pn28080k
+ SOC := rtl8380
+ IMAGE_SIZE := 16384k
+ DEVICE_VENDOR := Panasonic
+ DEVICE_MODEL := Switch-M8eG
+ DEVICE_VARIANT := PN28080K
+ DEVICE_PACKAGES := kmod-i2c-mux-pca954x
+endef
+TARGET_DEVICES += panasonic_m8eg-pn28080k
+
define Device/zyxel_gs1900
SOC := rtl8380
IMAGE_SIZE := 6976k
More information about the lede-commits
mailing list