[openwrt/openwrt] ath79: add support for ASUS PL-AC56
LEDE Commits
lede-commits at lists.infradead.org
Wed Jun 29 15:37:01 PDT 2022
hauke pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/e1dcaeb55c939365cdd27e469b63fca295bf1a2e
commit e1dcaeb55c939365cdd27e469b63fca295bf1a2e
Author: Tamas Balogh <tamasbalogh at hotmail.com>
AuthorDate: Tue Jun 28 12:31:59 2022 +0200
ath79: add support for ASUS PL-AC56
Asus PL-AC56 Powerline Range Extender Rev.A1
(in kit with Asus PL-E56P Powerline-slave)
Hardware specifications:
Board: AP152
SoC: QCA9563 2.4G n 3x3
PLC: QCA7500
WiFi: QCA9882 5G ac 2x2
Switch: QCA8337 3x1000M
Flash: 16MB 25L12835F SPI-NOR
DRAM SoC: 64MB w9751g6kb-25
DRAM PLC: 128MB w631gg6kb-15
Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz
MAC addresses as verified by OEM firmware:
use address source
Lan/Wan/PLC *:10 art 0x1002 (label)
2G *:10 art 0x1000
5G *:14 art 0x5000
Important notes:
the PLC firmware has to be provided and copied manually onto the
device! The PLC here has no dedicated flash, thus the firmware file
has to be uploaded to the PLC controller at every system start
the PLC functionality is managed by the script /etc/init.d/plc_basic,
a very basic script based on the the one from Netadair (netadair dot de)
Installation:
Asus windows recovery tool:
have to have the latest Asus firmware flashed before continuing!
install the Asus firmware restoration utility
unplug the router, hold the reset button while powering it on
release when the power LED flashes slowly
specify a static IP on your computer:
IP address: 192.168.1.75
Subnet mask 255.255.255.0
start the Asus firmware restoration utility, specify the factory image
and press upload
do NOT power off the device after OpenWrt has booted until the LED flashing
TFTP Recovery method:
have to have the latest Asus firmware flashed before continuing!
set computer to a static ip, 192.168.1.75
connect computer to the LAN 1 port of the router
hold the reset button while powering on the router for a few seconds
send firmware image using a tftp client; i.e from linux:
$ tftp
tftp> binary
tftp> connect 192.168.1.1
tftp> put factory.bin
tftp> quit
do NOT power off the device after OpenWrt has booted until the LED flashing
Additional notes:
the pairing buttons have to have pressed for at least half a second,
it doesn't matter on which plc device (master or slave) first
it is possible to pair the devices without the button-pairing requirement
simply by pressing reset on the slave device. This will default to the
firmware settings, which is also how the plc_basic script is setting up
the master device, i.e. configuring it to firmware defaults
the PL-E56P slave PLC has its dedicated 4MByte SPI, thus it is capable
to store all firmware currently available. Note that some other
slave devices are not guarantied to have the capacity for the newer
~1MByte firmware blobs!
To have a good overlook about the slave device, here are its specs:
same QCA7500 PLC controller, same w631gg6kb-15 128MB RAM,
25L3233F 4MB SPI-NOR and an AR8035-A 1000M-Transceiver
Signed-off-by: Tamas Balogh <tamasbalogh at hotmail.com>
---
target/linux/ath79/dts/qca9563_asus_pl-ac56.dts | 156 +++++++++++++++++++++
.../ath79/generic/base-files/etc/board.d/01_leds | 5 +
.../generic/base-files/etc/board.d/02_network | 5 +
.../base-files/etc/board.d/03_gpio_switches | 3 +
.../etc/hotplug.d/firmware/10-ath9k-eeprom | 1 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 1 +
target/linux/ath79/image/generic.mk | 13 ++
7 files changed, 184 insertions(+)
diff --git a/target/linux/ath79/dts/qca9563_asus_pl-ac56.dts b/target/linux/ath79/dts/qca9563_asus_pl-ac56.dts
new file mode 100644
index 0000000000..c597b566aa
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_asus_pl-ac56.dts
@@ -0,0 +1,156 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca956x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "ASUS PL-AC56";
+ compatible = "asus,pl-ac56", "qca,qca9563";
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-upgrade = &led_power;
+ label-mac-device = ð0;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ linux,code = <BTN_0>;
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+
+ wps {
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "red:power";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ };
+
+ lan {
+ label = "green:lan";
+ gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan2g {
+ label = "green:wlan2g";
+ gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan5g {
+ label = "green:wlan5g";
+ gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&spi {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x000000 0x40000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "u-boot-env";
+ reg = <0x040000 0x10000>;
+ read-only;
+ };
+
+ art: partition at 50000 {
+ label = "art";
+ reg = <0x050000 0x10000>;
+ read-only;
+
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_art_1002: macaddr at 1002 {
+ reg = <0x1002 0x6>;
+ };
+ };
+
+ partition at 60000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x060000 0xf20000>;
+ };
+
+ partition at f80000 {
+ label = "plc";
+ reg = <0xf80000 0x80000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy-mask = <0>;
+
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ phy-mode = "sgmii";
+ qca,mib-poll-interval = <500>;
+
+ qca,ar8327-initvals = <
+ 0x04 0x80000080 /* AR8327_REG_PAD0_MODE */
+ 0x08 0x01000000 /* AR8327_REG_PAD5_MODE */
+ 0x0c 0x07500000 /* AR8327_REG_PAD6_MODE */
+ 0x10 0x602613a0 /* AR8327_REG_POWER_ON_STRAP */
+ 0x50 0xcc35cc35 /* AR8327_REG_LED_CTRL0 */
+ 0x54 0xca35ca35 /* AR8327_REG_LED_CTRL1 */
+ 0x58 0xc935c935 /* AR8327_REG_LED_CTRL2 */
+ 0x5c 0x03ffff00 /* AR8327_REG_LED_CTRL3 */
+ 0x7c 0x0000007e /* AR8327_REG_PORT_STATUS(0) */
+ 0x94 0x0000007e /* AR8327_REG_PORT_STATUS(6) */
+ >;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ phy-mode = "sgmii";
+ nvmem-cells = <&macaddr_art_1002>;
+ nvmem-cell-names = "mac-address";
+ phy-handle = <&phy0>;
+};
+
+&wmac {
+ status = "okay";
+
+ qca,no-eeprom;
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index 93438b1498..0802b8345f 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -56,6 +56,11 @@ alfa-network,tube-2hq)
ucidef_set_led_rssi "signal3" "SIGNAL3" "green:signal3" "wlan0" "50" "100"
ucidef_set_led_rssi "signal4" "SIGNAL4" "green:signal4" "wlan0" "75" "100"
;;
+asus,pl-ac56)
+ ucidef_set_led_switch "lan" "LAN" "green:lan" "switch0" "0x3e"
+ ucidef_set_led_netdev "wlan2g" "WLAN2G" "green:wlan2g" "wlan1" "link"
+ ucidef_set_led_netdev "wlan5g" "WLAN5G" "green:wlan5g" "wlan0" "link"
+ ;;
asus,rp-ac66)
ucidef_set_rssimon "wlan0" "200000" "1"
ucidef_set_rssimon "wlan1" "200000" "1"
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index 7ba39c4c49..8405c5f521 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -127,6 +127,11 @@ ath79_setup_interfaces()
ubnt,unifi-ap-outdoor-plus)
ucidef_set_interface_lan "eth0 eth1"
;;
+ asus,pl-ac56)
+ # port 6 (internal) is the power-line port
+ ucidef_add_switch "switch0" \
+ "0 at eth0" "1:lan:1" "2:lan:2" "3:lan:3" "6:lan:4"
+ ;;
atheros,db120)
ucidef_add_switch "switch0" \
"0 at eth0" "2:lan" "3:lan" "4:lan" "5:lan" "1:wan"
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/03_gpio_switches b/target/linux/ath79/generic/base-files/etc/board.d/03_gpio_switches
index ca7d8c633c..899a8ba97e 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/03_gpio_switches
+++ b/target/linux/ath79/generic/base-files/etc/board.d/03_gpio_switches
@@ -24,6 +24,9 @@ adtran,bsap1840)
ucidef_add_gpio_switch "wifi0_ext_c" "2.4GHz External Antenna C" "509" "1"
ucidef_add_gpio_switch "wifi0_int_c" "2.4GHz Internal Antenna C" "510"
;;
+asus,pl-ac56)
+ ucidef_add_gpio_switch "plc_enable" "PLC enable" "14" "1"
+ ;;
comfast,cf-e5|\
telco,t1)
ucidef_add_gpio_switch "lte_power" "LTE Power" "14" "1"
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index 8631984ee8..3e4d9a556b 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -12,6 +12,7 @@ case "$FIRMWARE" in
8dev,lima)
caldata_extract "art" 0x1000 0x800
;;
+ asus,pl-ac56|\
asus,rp-ac66)
caldata_extract "art" 0x1000 0x440
;;
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 5c42ae4fac..f522268e59 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -19,6 +19,7 @@ case "$FIRMWARE" in
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) 2)
;;
+ asus,pl-ac56|\
asus,rp-ac66|\
comfast,cf-wr650ac-v1|\
comfast,cf-wr650ac-v2|\
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 24e828956c..6fc844b4b2 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -376,6 +376,19 @@ define Device/aruba_ap-105
endef
TARGET_DEVICES += aruba_ap-105
+define Device/asus_pl-ac56
+ SOC := qca9563
+ DEVICE_VENDOR := ASUS
+ DEVICE_MODEL := PL-AC56
+ DEVICE_VARIANT := A1
+ IMAGE_SIZE := 15488k
+ IMAGES += factory.bin
+ IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
+ append-rootfs | pad-rootfs
+ DEVICE_PACKAGES := kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct
+endef
+TARGET_DEVICES += asus_pl-ac56
+
define Device/asus_rp-ac66
SOC := qca9563
DEVICE_VENDOR := ASUS
More information about the lede-commits
mailing list