[openwrt/openwrt] Revert "realtek: remove support for HPE 1920 series"
LEDE Commits
lede-commits at lists.infradead.org
Thu Jul 28 07:46:26 PDT 2022
dangole pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/a49212d762fb2635564cd3365651da51d0c535d9
commit a49212d762fb2635564cd3365651da51d0c535d9
Author: Daniel Golle <daniel at makrotopia.org>
AuthorDate: Thu Jul 28 16:45:03 2022 +0200
Revert "realtek: remove support for HPE 1920 series"
This reverts commit a63aeaecf1f3387df020854c9b22a365207399ce.
Signed-off-by: Daniel Golle <daniel at makrotopia.org>
---
.../realtek/base-files/etc/board.d/02_network | 18 +++-
.../linux/realtek/dts-5.10/rtl8380_hpe_1920-8g.dts | 113 ++++++++++++++++++++
.../realtek/dts-5.10/rtl8382_hpe_1920-16g.dts | 48 +++++++++
.../realtek/dts-5.10/rtl8382_hpe_1920-24g.dts | 68 ++++++++++++
.../linux/realtek/dts-5.10/rtl8382_hpe_1920.dtsi | 117 +++++++++++++++++++++
target/linux/realtek/dts-5.10/rtl838x.dtsi | 7 ++
.../linux/realtek/dts-5.10/rtl838x_hpe_1920.dtsi | 96 +++++++++++++++++
target/linux/realtek/image/Makefile | 49 +++++++++
target/linux/realtek/image/rtl838x.mk | 24 +++++
target/linux/realtek/rtl838x/config-5.10 | 3 +
10 files changed, 540 insertions(+), 3 deletions(-)
diff --git a/target/linux/realtek/base-files/etc/board.d/02_network b/target/linux/realtek/base-files/etc/board.d/02_network
index af9db848dd..5356bcac65 100644
--- a/target/linux/realtek/base-files/etc/board.d/02_network
+++ b/target/linux/realtek/base-files/etc/board.d/02_network
@@ -22,9 +22,20 @@ ucidef_set_bridge_device switch
ucidef_set_interface_lan "$lan_list"
lan_mac=""
+lan_mac_start=""
lan_mac_end=""
label_mac=""
case $board in
+hpe,1920-8g|\
+hpe,1920-16g|\
+hpe,1920-24g)
+ label_mac=$(mtd_get_mac_binary factory 0x68)
+ lan_mac=$label_mac
+ mac_count1=$(hexdump -v -n 4 -s 0x110 -e '4 "%d"' $(find_mtd_part factory) 2>/dev/null)
+ mac_count2=$(hexdump -v -n 4 -s 0x114 -e '4 "%d"' $(find_mtd_part factory) 2>/dev/null)
+ lan_mac_start=$(macaddr_add $lan_mac 2)
+ lan_mac_end=$(macaddr_add $lan_mac $((mac_count2-mac_count1)))
+ ;;
*)
lan_mac=$(mtd_get_mac_ascii u-boot-env2 mac_start)
lan_mac_end=$(mtd_get_mac_ascii u-boot-env2 mac_end)
@@ -36,10 +47,11 @@ esac
ucidef_set_interface_macaddr "lan" $lan_mac
ucidef_set_bridge_mac "$lan_mac"
ucidef_set_network_device_mac eth0 $lan_mac
+[ -z "$lan_mac_start" ] && lan_mac_start=$lan_mac
for lan in $lan_list; do
- ucidef_set_network_device_mac $lan $lan_mac
- [ -z "$lan_mac_end" ] || [ "$lan_mac" == "$lan_mac_end" ] && lan_mac=$(macaddr_setbit_la $lan_mac)
- lan_mac=$(macaddr_add $lan_mac 1)
+ ucidef_set_network_device_mac $lan $lan_mac_start
+ [ -z "$lan_mac_end" ] || [ "$lan_mac_start" == "$lan_mac_end" ] && lan_mac_start=$(macaddr_setbit_la $lan_mac_start)
+ lan_mac_start=$(macaddr_add $lan_mac_start 1)
done
[ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac
diff --git a/target/linux/realtek/dts-5.10/rtl8380_hpe_1920-8g.dts b/target/linux/realtek/dts-5.10/rtl8380_hpe_1920-8g.dts
new file mode 100644
index 0000000000..b51c75f355
--- /dev/null
+++ b/target/linux/realtek/dts-5.10/rtl8380_hpe_1920-8g.dts
@@ -0,0 +1,113 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "rtl838x.dtsi"
+#include "rtl838x_hpe_1920.dtsi"
+
+/ {
+ compatible = "hpe,1920-8g", "realtek,rtl838x-soc";
+ model = "HPE 1920-8G (JG920A)";
+
+ gpio1: rtl8231-gpio {
+ compatible = "realtek,rtl8231-gpio";
+ #gpio-cells = <2>;
+ gpio-controller;
+ indirect-access-bus-id = <0>;
+ };
+
+ i2c0: i2c-gpio-0 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&gpio1 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio1 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ sfp0: sfp-0 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c0>;
+ los-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ // tx-fault and tx-disable unconnected
+ };
+
+ i2c1: i2c-gpio-1 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&gpio1 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio1 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ sfp1: sfp-1 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c1>;
+ los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&gpio1 21 GPIO_ACTIVE_LOW>;
+ // tx-fault and tx-disable unconnected
+ };
+};
+
+ðernet0 {
+ mdio: mdio-bus {
+ compatible = "realtek,rtl838x-mdio";
+ regmap = <ðernet0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ INTERNAL_PHY(8)
+ INTERNAL_PHY(9)
+ INTERNAL_PHY(10)
+ INTERNAL_PHY(11)
+ INTERNAL_PHY(12)
+ INTERNAL_PHY(13)
+ INTERNAL_PHY(14)
+ INTERNAL_PHY(15)
+
+ INTERNAL_PHY(24)
+ INTERNAL_PHY(26)
+ };
+};
+
+&switch0 {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ SWITCH_PORT(8, 1, internal)
+ SWITCH_PORT(9, 2, internal)
+ SWITCH_PORT(10, 3, internal)
+ SWITCH_PORT(11, 4, internal)
+ SWITCH_PORT(12, 5, internal)
+ SWITCH_PORT(13, 6, internal)
+ SWITCH_PORT(14, 7, internal)
+ SWITCH_PORT(15, 8, internal)
+
+ port at 24 {
+ reg = <24>;
+ label = "lan9";
+ phy-mode = "1000base-x";
+ managed = "in-band-status";
+ sfp = <&sfp0>;
+ };
+
+ port at 26 {
+ reg = <26>;
+ label = "lan10";
+ phy-mode = "1000base-x";
+ managed = "in-band-status";
+ sfp = <&sfp1>;
+ };
+
+ port at 28 {
+ ethernet = <ðernet0>;
+ reg = <28>;
+ phy-mode = "internal";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+};
diff --git a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-16g.dts b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-16g.dts
new file mode 100644
index 0000000000..59043b2f6f
--- /dev/null
+++ b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-16g.dts
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "rtl8382_hpe_1920.dtsi"
+
+/ {
+ compatible = "hpe,1920-16g", "realtek,rtl838x-soc";
+ model = "HPE 1920-16G (JG923A)";
+};
+
+&switch0 {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ SWITCH_PORT(8, 1, internal)
+ SWITCH_PORT(9, 2, internal)
+ SWITCH_PORT(10, 3, internal)
+ SWITCH_PORT(11, 4, internal)
+ SWITCH_PORT(12, 5, internal)
+ SWITCH_PORT(13, 6, internal)
+ SWITCH_PORT(14, 7, internal)
+ SWITCH_PORT(15, 8, internal)
+
+ SWITCH_PORT(16, 9, qsgmii)
+ SWITCH_PORT(17, 10, qsgmii)
+ SWITCH_PORT(18, 11, qsgmii)
+ SWITCH_PORT(19, 12, qsgmii)
+ SWITCH_PORT(20, 13, qsgmii)
+ SWITCH_PORT(21, 14, qsgmii)
+ SWITCH_PORT(22, 15, qsgmii)
+ SWITCH_PORT(23, 16, qsgmii)
+
+ SWITCH_PORT(24, 17, qsgmii)
+ SWITCH_PORT(25, 18, qsgmii)
+ SWITCH_PORT(26, 19, qsgmii)
+ SWITCH_PORT(27, 20, qsgmii)
+
+ port at 28 {
+ ethernet = <ðernet0>;
+ reg = <28>;
+ phy-mode = "internal";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+};
diff --git a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-24g.dts b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-24g.dts
new file mode 100644
index 0000000000..61781c708e
--- /dev/null
+++ b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-24g.dts
@@ -0,0 +1,68 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "rtl8382_hpe_1920.dtsi"
+
+/ {
+ compatible = "hpe,1920-24g", "realtek,rtl838x-soc";
+ model = "HPE 1920-24G (JG924A)";
+};
+
+&mdio {
+ EXTERNAL_PHY(0)
+ EXTERNAL_PHY(1)
+ EXTERNAL_PHY(2)
+ EXTERNAL_PHY(3)
+ EXTERNAL_PHY(4)
+ EXTERNAL_PHY(5)
+ EXTERNAL_PHY(6)
+ EXTERNAL_PHY(7)
+};
+
+&switch0 {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ SWITCH_PORT(0, 1, qsgmii)
+ SWITCH_PORT(1, 2, qsgmii)
+ SWITCH_PORT(2, 3, qsgmii)
+ SWITCH_PORT(3, 4, qsgmii)
+ SWITCH_PORT(4, 5, qsgmii)
+ SWITCH_PORT(5, 6, qsgmii)
+ SWITCH_PORT(6, 7, qsgmii)
+ SWITCH_PORT(7, 8, qsgmii)
+
+ SWITCH_PORT(8, 9, internal)
+ SWITCH_PORT(9, 10, internal)
+ SWITCH_PORT(10, 11, internal)
+ SWITCH_PORT(11, 12, internal)
+ SWITCH_PORT(12, 13, internal)
+ SWITCH_PORT(13, 14, internal)
+ SWITCH_PORT(14, 15, internal)
+ SWITCH_PORT(15, 16, internal)
+
+ SWITCH_PORT(16, 17, qsgmii)
+ SWITCH_PORT(17, 18, qsgmii)
+ SWITCH_PORT(18, 19, qsgmii)
+ SWITCH_PORT(19, 20, qsgmii)
+ SWITCH_PORT(20, 21, qsgmii)
+ SWITCH_PORT(21, 22, qsgmii)
+ SWITCH_PORT(22, 23, qsgmii)
+ SWITCH_PORT(23, 24, qsgmii)
+
+ SWITCH_PORT(24, 25, qsgmii)
+ SWITCH_PORT(25, 26, qsgmii)
+ SWITCH_PORT(26, 27, qsgmii)
+ SWITCH_PORT(27, 28, qsgmii)
+
+ port at 28 {
+ ethernet = <ðernet0>;
+ reg = <28>;
+ phy-mode = "internal";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+};
diff --git a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920.dtsi b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920.dtsi
new file mode 100644
index 0000000000..5368b41c27
--- /dev/null
+++ b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920.dtsi
@@ -0,0 +1,117 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "rtl838x.dtsi"
+#include "rtl838x_hpe_1920.dtsi"
+
+/ {
+ gpio1: rtl8231-gpio {
+ compatible = "realtek,rtl8231-gpio";
+ #gpio-cells = <2>;
+ gpio-controller;
+ indirect-access-bus-id = <0>;
+ };
+
+ i2c0: i2c-gpio-0 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&gpio1 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio1 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ sfp0: sfp-0 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c0>;
+ los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&gpio1 21 GPIO_ACTIVE_LOW>;
+ // tx-fault unconnected
+ // tx-disable connected to RTL8214FC
+ };
+
+ i2c1: i2c-gpio-1 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&gpio1 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio1 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ sfp1: sfp-1 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c1>;
+ los-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ // tx-fault unconnected
+ // tx-disable connected to RTL8214FC
+ };
+
+ i2c2: i2c-gpio-2 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&gpio1 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio1 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ sfp2: sfp-2 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c2>;
+ los-gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>;
+ // tx-fault unconnected
+ // tx-disable connected to RTL8214FC
+ };
+
+ i2c3: i2c-gpio-3 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpio1 32 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ sfp3: sfp-3 {
+ compatible = "sff,sfp";
+ i2c-bus = <&i2c3>;
+ los-gpio = <&gpio1 34 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpio = <&gpio1 33 GPIO_ACTIVE_LOW>;
+ // tx-fault unconnected
+ // tx-disable connected to RTL8214FC
+ };
+};
+
+ðernet0 {
+ mdio: mdio-bus {
+ compatible = "realtek,rtl838x-mdio";
+ regmap = <ðernet0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ INTERNAL_PHY(8)
+ INTERNAL_PHY(9)
+ INTERNAL_PHY(10)
+ INTERNAL_PHY(11)
+ INTERNAL_PHY(12)
+ INTERNAL_PHY(13)
+ INTERNAL_PHY(14)
+ INTERNAL_PHY(15)
+
+ EXTERNAL_PHY(16)
+ EXTERNAL_PHY(17)
+ EXTERNAL_PHY(18)
+ EXTERNAL_PHY(19)
+ EXTERNAL_PHY(20)
+ EXTERNAL_PHY(21)
+ EXTERNAL_PHY(22)
+ EXTERNAL_PHY(23)
+
+ EXTERNAL_SFP_PHY_FULL(24, 0)
+ EXTERNAL_SFP_PHY_FULL(25, 1)
+ EXTERNAL_SFP_PHY_FULL(26, 2)
+ EXTERNAL_SFP_PHY_FULL(27, 3)
+ };
+};
diff --git a/target/linux/realtek/dts-5.10/rtl838x.dtsi b/target/linux/realtek/dts-5.10/rtl838x.dtsi
index 11cabc3f63..41fdbdae20 100644
--- a/target/linux/realtek/dts-5.10/rtl838x.dtsi
+++ b/target/linux/realtek/dts-5.10/rtl838x.dtsi
@@ -27,6 +27,13 @@
reg = <##n>; \
};
+#define EXTERNAL_SFP_PHY_FULL(n, s) \
+ phy##n: ethernet-phy@##n { \
+ compatible = "ethernet-phy-ieee802.3-c22"; \
+ sfp = <&sfp##s>; \
+ reg = <##n>; \
+ };
+
#define SWITCH_PORT(n, s, m) \
port@##n { \
reg = <##n>; \
diff --git a/target/linux/realtek/dts-5.10/rtl838x_hpe_1920.dtsi b/target/linux/realtek/dts-5.10/rtl838x_hpe_1920.dtsi
new file mode 100644
index 0000000000..8e29af62bb
--- /dev/null
+++ b/target/linux/realtek/dts-5.10/rtl838x_hpe_1920.dtsi
@@ -0,0 +1,96 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ chosen {
+ bootargs = "console=ttyS0,38400";
+ };
+
+ memory at 0 {
+ device_type = "memory";
+ reg = <0x0 0x8000000>;
+ };
+
+ watchdog1: watchdog {
+ // PT7A7514
+ compatible = "linux,wdt-gpio";
+ gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
+ hw_algo = "toggle";
+ hw_margin_ms = <1000>;
+ always-running;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinmux_disable_sys_led>;
+ };
+};
+
+&watchdog0 {
+ status = "disabled";
+};
+
+&spi0 {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ m25p,fast-read;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "bootware_basic";
+ reg = <0x0 0x50000>;
+ read-only;
+ };
+
+ partition at 0x60000 {
+ label = "bootware_data";
+ reg = <0x60000 0x30000>;
+ read-only;
+ };
+
+ partition at 0x90000 {
+ label = "bootware_extend";
+ reg = <0x90000 0x40000>;
+ read-only;
+ };
+
+ partition at 0x100000 {
+ label = "bootware_basic_backup";
+ reg = <0x100000 0x50000>;
+ read-only;
+ };
+
+ partition at 0x160000 {
+ label = "bootware_data_backup";
+ reg = <0x160000 0x30000>;
+ read-only;
+ };
+
+ partition at 0x190000 {
+ label = "bootware_extend_backup";
+ reg = <0x190000 0x40000>;
+ read-only;
+ };
+
+ partition at 0x300000 {
+ label = "firmware";
+ compatible = "h3c,vfs-firmware";
+ reg = <0x300000 0x1cf0000>;
+ };
+
+ partition at 0x1ff0000 {
+ label = "factory";
+ reg = <0x1ff0000 0x10000>;
+ read-only;
+ };
+ };
+ };
+};
diff --git a/target/linux/realtek/image/Makefile b/target/linux/realtek/image/Makefile
index cf779002e8..6165d99bfc 100644
--- a/target/linux/realtek/image/Makefile
+++ b/target/linux/realtek/image/Makefile
@@ -8,6 +8,7 @@ KERNEL_ENTRY = 0x80000400
DEVICE_VARS += ZYXEL_VERS DLINK_KERNEL_PART_SIZE
DEVICE_VARS += CAMEO_KERNEL_PART CAMEO_ROOTFS_PART CAMEO_CUSTOMER_SIGNATURE CAMEO_BOARD_VERSION
+DEVICE_VARS += H3C_PRODUCT_ID H3C_DEVICE_ID
define Build/zyxel-vers
( echo VERS;\
@@ -41,6 +42,43 @@ define Build/dlink-headers
cat $@.kernel_part.hex $@.rootfs_part.hex > $@
endef
+define Build/7z
+ $(STAGING_DIR_HOST)/bin/7zr a $(@).new -t7z -m0=lzma $(@)
+ mv $@.new $@
+endef
+
+define Build/h3c-image
+ $(STAGING_DIR_HOST)/bin/mkh3cimg \
+ -i $(@) \
+ -o $(@).new \
+ -c 7z \
+ -p $(H3C_PRODUCT_ID) \
+ -d $(H3C_DEVICE_ID)
+ mv $@.new $@
+endef
+
+define Build/h3c-vfs
+ $(STAGING_DIR_HOST)/bin/mkh3cvfs \
+ -i $(@) \
+ -o $(@).new \
+ -f openwrt-kernel.bin
+ mv $@.new $@
+endef
+
+define Build/relocate-kernel
+ rm -rf $@.relocate
+ $(CP) ../../generic/image/relocate $@.relocate
+ $(MAKE) -j1 -C $@.relocate KERNEL_ADDR=$(KERNEL_LOADADDR) LZMA_TEXT_START=0x82000000 \
+ CROSS_COMPILE=$(TARGET_CROSS)
+ ( \
+ dd if=$@.relocate/loader.bin bs=32 conv=sync && \
+ perl -e '@s = stat("$@"); print pack("N", @s[7])' && \
+ cat "$@" \
+ ) > "$@.new"
+ mv "$@.new" "$@"
+ rm -rf $@.relocate
+endef
+
define Device/Default
PROFILES = Default
KERNEL := kernel-bin | append-dtb | gzip | uImage gzip
@@ -52,6 +90,17 @@ define Device/Default
check-size | append-metadata
endef
+define Device/hpe_1920
+ DEVICE_VENDOR := HPE
+ IMAGE_SIZE := 29632k
+ BLOCKSIZE := 64k
+ H3C_PRODUCT_ID := 0x3c010501
+ KERNEL := kernel-bin | append-dtb | relocate-kernel | 7z | h3c-image | h3c-vfs
+ KERNEL_INITRAMFS := kernel-bin | append-dtb | relocate-kernel | 7z | h3c-image
+ IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
+ pad-rootfs | check-size | append-metadata
+endef
+
# "NGE" refers to the uImage magic
define Device/netgear_nge
KERNEL := kernel-bin | append-dtb | lzma | uImage lzma
diff --git a/target/linux/realtek/image/rtl838x.mk b/target/linux/realtek/image/rtl838x.mk
index 887f82e385..60eda5359d 100644
--- a/target/linux/realtek/image/rtl838x.mk
+++ b/target/linux/realtek/image/rtl838x.mk
@@ -65,6 +65,30 @@ define Device/engenius_ews2910p
endef
TARGET_DEVICES += engenius_ews2910p
+define Device/hpe_1920-8g
+ $(Device/hpe_1920)
+ SOC := rtl8380
+ DEVICE_MODEL := 1920-8G (JG920A)
+ H3C_DEVICE_ID := 0x00010023
+endef
+TARGET_DEVICES += hpe_1920-8g
+
+define Device/hpe_1920-16g
+ $(Device/hpe_1920)
+ SOC := rtl8382
+ DEVICE_MODEL := 1920-16G (JG923A)
+ H3C_DEVICE_ID := 0x00010026
+endef
+TARGET_DEVICES += hpe_1920-16g
+
+define Device/hpe_1920-24g
+ $(Device/hpe_1920)
+ SOC := rtl8382
+ DEVICE_MODEL := 1920-24G (JG924A)
+ H3C_DEVICE_ID := 0x00010027
+endef
+TARGET_DEVICES += hpe_1920-24g
+
define Device/inaba_aml2-17gp
SOC := rtl8382
IMAGE_SIZE := 13504k
diff --git a/target/linux/realtek/rtl838x/config-5.10 b/target/linux/realtek/rtl838x/config-5.10
index c117fc489a..9075aa6d3c 100644
--- a/target/linux/realtek/rtl838x/config-5.10
+++ b/target/linux/realtek/rtl838x/config-5.10
@@ -74,6 +74,8 @@ CONFIG_GPIO_PCA953X=y
CONFIG_GPIO_PCA953X_IRQ=y
CONFIG_GPIO_REALTEK_OTTO=y
CONFIG_GPIO_RTL8231=y
+CONFIG_GPIO_WATCHDOG=y
+# CONFIG_GPIO_WATCHDOG_ARCH_INITCALL is not set
CONFIG_GRO_CELLS=y
CONFIG_HANDLE_DOMAIN_IRQ=y
CONFIG_HARDWARE_WATCHPOINTS=y
@@ -134,6 +136,7 @@ CONFIG_MTD_SPI_NOR=y
CONFIG_MTD_SPLIT_BRNIMAGE_FW=y
CONFIG_MTD_SPLIT_EVA_FW=y
CONFIG_MTD_SPLIT_FIRMWARE=y
+CONFIG_MTD_SPLIT_H3C_VFS=y
CONFIG_MTD_SPLIT_TPLINK_FW=y
CONFIG_MTD_SPLIT_UIMAGE_FW=y
CONFIG_NEED_DMA_MAP_STATE=y
More information about the lede-commits
mailing list