[openwrt/openwrt] ramips: improve YunCore AX820 LEDs

[LEDE Commits]

ansuel pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/a0e1d3ab7b4ff06cf755884329e0742b1582badd

commit a0e1d3ab7b4ff06cf755884329e0742b1582badd
Author: Thibaut VARÈNE <hacks at slashdirt.org>
AuthorDate: Thu Jun 30 10:06:35 2022 +0200

    ramips: improve YunCore AX820 LEDs
    
    At least two AX820 hardware variants are known to exist, but they cannot
    be distinguished (same hardware revision, no specific markings).
    
    They appear to have the same LED hardware, but wired differently:
    
    - One has a red system LED at GPIO 15, a green wlan2g LED at GPIO 14 and
      a blue wlan5g LED at GPIO 16;
    - The other only offers a green system LED at GPIO 15, with GPIO 14 and
      16 being apparently not connected
    
    Finally, a Yuncore datasheet says the canonical wiring should be:
    - Blue wlan2g GPIO 14, green system GPIO 15, red wlan5g GPIO 16
    
    All GPIOs are tied to a single RGB LED which is exposed via lightpipe on
    the device front casing.
    
    Considering the above, this patch exposes all three LEDs, preserves the
    common system LED (GPIO 15) as the openwrt status LED, and removes the
    color information from the LEDs names since it is not consistent across
    hardware. The LED naming is made consistent with other YunCore devices.
    A note is added in DTS to ensure this information is always available
    and prevent unwanted changes in the future.
    
    Fixes: #10131 "YunCore AX820: GPIO LED not correct"
    
    Reviewed-by: Sander Vanheule <sander at svanheule.net>
    Signed-off-by: Thibaut VARÈNE <hacks at slashdirt.org>
---
 target/linux/ramips/dts/mt7621_yuncore_ax820.dts | 32 +++++++++++++++++++-----
 1 file changed, 26 insertions(+), 6 deletions(-)

diff --git a/target/linux/ramips/dts/mt7621_yuncore_ax820.dts b/target/linux/ramips/dts/mt7621_yuncore_ax820.dts
index fe0e9daf7f..9638f1f060 100644
--- a/target/linux/ramips/dts/mt7621_yuncore_ax820.dts
+++ b/target/linux/ramips/dts/mt7621_yuncore_ax820.dts
@@ -10,10 +10,10 @@
 	model = "YunCore AX820";
 
 	aliases {
-		led-boot = &led_status_green;
-		led-failsafe = &led_status_green;
-		led-running = &led_status_green;
-		led-upgrade = &led_status_green;
+		led-boot = &led_system;
+		led-failsafe = &led_system;
+		led-running = &led_system;
+		led-upgrade = &led_system;
 	};
 
 	chosen {
@@ -23,10 +23,30 @@
 	leds {
 		compatible = "gpio-leds";
 
-		led_status_green: status_green {
-			label = "green:status";
+		/* At least 2 AX820 variants are known and cannot be distinguished (same hw rev):
+		   - System LED green GPIO 15; red and blue apparently not connected
+		   - System LED red GPIO 15, WLAN2G LED green GPIO 14, WLAN5G LED blue GPIO 16
+		   The canonical values taken from a Yuncore datasheet are:
+		   - System LED green GPIO 15, WLAN2G LED blue GPIO 14, WLAN5G LED red GPIO 16
+		   All 3 colors relate to the same single RGB LED showing up on the front lightpipe.
+		   As a result, all 3 LEDs are defined even if only one may be available, and
+		   the color information is absent as it is not reliable */
+		wlan2g {
+			label = "wlan2g";
+			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0radio";
+		};
+
+		led_system: system {
+			label = "system";
 			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
 		};
+
+		wlan5g {
+			label = "wlan5g";
+			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy1radio";
+		};
 	};
 
 	watchdog {