[openwrt/openwrt] ath79: Add support for OpenMesh OM5P-AC v1
LEDE Commits
lede-commits at lists.infradead.org
Sun Jan 9 12:12:35 PST 2022
hauke pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/97f561725962ddb8823b2e01563a0f37f7930477
commit 97f561725962ddb8823b2e01563a0f37f7930477
Author: Sven Eckelmann <sven at narfation.org>
AuthorDate: Mon Nov 23 13:41:34 2020 +0100
ath79: Add support for OpenMesh OM5P-AC v1
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/240 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
- eth0
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as LAN interface
- eth1
+ AR8035 ethernet PHY (SGMII)
+ 10/100/1000 Mbps Ethernet
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root at 192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven at narfation.org>
---
package/boot/uboot-envtools/files/ath79 | 1 +
.../ath79/dts/qca9558_openmesh_om5p-ac-v1.dts | 216 +++++++++++++++++++++
.../ath79/generic/base-files/etc/board.d/01_leds | 4 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 4 +
.../generic/base-files/lib/upgrade/platform.sh | 1 +
target/linux/ath79/image/generic.mk | 11 ++
6 files changed, 237 insertions(+)
diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79
index 2ad15a7a40..b01a713705 100644
--- a/package/boot/uboot-envtools/files/ath79
+++ b/package/boot/uboot-envtools/files/ath79
@@ -58,6 +58,7 @@ openmesh,mr1750-v1|\
openmesh,mr1750-v2|\
openmesh,om5p|\
openmesh,om5p-an|\
+openmesh,om5p-ac-v1|\
openmesh,om5p-ac-v2|\
samsung,wam250|\
ubnt,nanostation-m|\
diff --git a/target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v1.dts b/target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v1.dts
new file mode 100644
index 0000000000..de21f0119f
--- /dev/null
+++ b/target/linux/ath79/dts/qca9558_openmesh_om5p-ac-v1.dts
@@ -0,0 +1,216 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca955x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "openmesh,om5p-ac-v1", "qca,qca9558";
+ model = "OpenMesh OM5P-AC v1";
+
+ chosen {
+ /delete-property/ bootargs;
+ };
+
+ aliases {
+ serial0 = &uart;
+ led-boot = &led_power_blue;
+ led-failsafe = &led_power_blue;
+ led-running = &led_power_blue;
+ led-upgrade = &led_power_blue;
+ label-mac-device = ð0;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power_blue: power_blue {
+ label = "blue:power";
+ gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ wan_blue {
+ label = "blue:wan";
+ gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+ };
+
+ lan_blue {
+ label = "blue:lan";
+ gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
+ };
+
+ wifi_green {
+ label = "green:wifi";
+ gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wifi_yellow {
+ label = "yellow:wifi";
+ gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
+ };
+
+ wifi_red {
+ label = "red:wifi";
+ gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ i2c {
+ compatible = "i2c-gpio";
+ gpios = <&gpio 11 GPIO_ACTIVE_HIGH /* sda */
+ &gpio 12 GPIO_ACTIVE_HIGH /* scl */
+ >;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c-gpio,scl-open-drain;
+ i2c-gpio,sda-open-drain;
+
+ tmp423a at 4c {
+ compatible = "ti,tmp423";
+ reg = <0x4c>;
+ };
+ };
+
+ watchdog {
+ compatible = "linux,wdt-gpio";
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ hw_algo = "toggle";
+ /* hw_margin_ms is actually 300s but driver limits it to 60s */
+ hw_margin_ms = <60000>;
+ always-running;
+ };
+};
+
+&spi {
+ status = "okay";
+
+ flash at 0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+
+ /* partitions are passed via bootloader */
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition at 0 {
+ label = "u-boot";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ partition at 40000 {
+ label = "u-boot-env";
+ reg = <0x040000 0x010000>;
+ };
+
+ partition at 50000 {
+ label = "custom";
+ reg = <0x050000 0x060000>;
+ read-only;
+ };
+
+ partition at b0000 {
+ label = "inactive";
+ reg = <0x0b0000 0x7a0000>;
+ };
+
+ partition at 850000 {
+ label = "inactive2";
+ reg = <0x850000 0x7a0000>;
+ };
+
+ art: partition at ff0000 {
+ label = "ART";
+ reg = <0xff0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy-mask = <0x6>;
+
+ phy1: ethernet-phy at 1 {
+ reg = <1>;
+ eee-broken-100tx;
+ eee-broken-1000t;
+ };
+
+ phy2: ethernet-phy at 2 {
+ reg = <2>;
+ eee-broken-100tx;
+ eee-broken-1000t;
+ at803x-override-sgmii-link-check;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ pll-data = <0x82000101 0x80000101 0x80001313>;
+
+ nvmem-cells = <&macaddr_art_0>;
+ nvmem-cell-names = "mac-address";
+
+ phy-mode = "rgmii-id";
+ phy-handle = <&phy1>;
+
+ gmac-config {
+ device = <&gmac>;
+ rgmii-enabled = <1>;
+ rxd-delay = <3>;
+ rxdv-delay = <3>;
+ txd-delay = <0>;
+ txen-delay = <0>;
+ };
+};
+
+ð1 {
+ status = "okay";
+
+ pll-data = <0x03000101 0x80000101 0x80001313>;
+
+ nvmem-cells = <&macaddr_art_6>;
+ nvmem-cell-names = "mac-address";
+
+ qca955x-sgmii-fixup;
+
+ phy-handle = <&phy2>;
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+ nvmem-cells = <&macaddr_art_0>;
+ nvmem-cell-names = "mac-address";
+ mac-address-increment = <2>;
+};
+
+&pcie1 {
+ status = "okay";
+};
+
+&art {
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_art_0: macaddr at 0 {
+ reg = <0x0 0x6>;
+ };
+
+ macaddr_art_6: macaddr at 6 {
+ reg = <0x6 0x6>;
+ };
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index 14b38b4e66..652b54092e 100644
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -271,6 +271,10 @@ openmesh,om2p-hs-v4)
ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth0"
ucidef_set_led_switch "lan" "LAN" "blue:lan" "switch0" "0x02"
;;
+openmesh,om5p-ac-v1)
+ ucidef_set_led_netdev "lan" "LAN" "blue:lan" "eth0"
+ ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth1"
+ ;;
openmesh,om5p-an)
ucidef_set_led_netdev "lan" "LAN" "blue:lan" "eth0"
ucidef_set_led_switch "wan" "WAN" "blue:wan" "switch0" "0x02"
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index ef9b8dee91..c0e5078bdb 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -165,6 +165,10 @@ case "$FIRMWARE" in
;;
"ath10k/cal-pci-0000:01:00.0.bin")
case $board in
+ openmesh,om5p-ac-v1)
+ caldata_extract "ART" 0x5000 0x844
+ ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
+ ;;
sitecom,wlr-8100)
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) 1)
diff --git a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
index b7e2930129..3d953d7982 100644
--- a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh
@@ -81,6 +81,7 @@ platform_do_upgrade() {
openmesh,om2p-hs-v4|\
openmesh,om2p-lc|\
openmesh,om5p|\
+ openmesh,om5p-ac-v1|\
openmesh,om5p-an)
PART_NAME="inactive"
platform_do_upgrade_openmesh "$1"
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index e17b498d88..8e97fec402 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -1913,6 +1913,17 @@ define Device/openmesh_om5p
endef
TARGET_DEVICES += openmesh_om5p
+define Device/openmesh_om5p-ac-v1
+ $(Device/openmesh_common_64k)
+ SOC := qca9558
+ DEVICE_MODEL := OM5P-AC
+ DEVICE_VARIANT := v1
+ DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct
+ OPENMESH_CE_TYPE := OM5PAC
+ SUPPORTED_DEVICES += om5p-ac
+endef
+TARGET_DEVICES += openmesh_om5p-ac-v1
+
define Device/openmesh_om5p-ac-v2
SOC := qca9558
DEVICE_VENDOR := OpenMesh
More information about the lede-commits
mailing list