[openwrt/openwrt] Revert "bcm27xx: bcm27xx: update defconfig"

[LEDE Commits]

chunkeey pushed a commit to openwrt/openwrt.git, branch master:
https://git.openwrt.org/83f2f1ad5840eae4bd265ffc46f1982571514123

commit 83f2f1ad5840eae4bd265ffc46f1982571514123
Author: Christian Lamparter <chunkeey at gmail.com>
AuthorDate: Thu Feb 24 17:21:42 2022 +0100

    Revert "bcm27xx: bcm27xx: update defconfig"
    
    This reverts all four commits
    dbb45421bab "bcm27xx: bcm2708: update defconfig"
    332f69583ad "bcm27xx: bcm2709: update defconfig"
    a478202d74b "bcm27xx: bcm2710: update defconfig"
    82da1dfd69a "bcm27xx: bcm2711: update defconfig"
    
    this also highlighted an unrelated kconfig failure
    that warrants investigation. But for now it is important
    for the bcm27xx target to come back again.
    
    |*
    |* Restart config...
    |*
    |*
    |* Allow override default queue discipline
    |*
    |Allow override default queue discipline (NET_SCH_DEFAULT) [Y/n/?] y
    |  Default queuing discipline
    |    1. Fair Queue (DEFAULT_FQ) (NEW)
    |    2. Controlled Delay (DEFAULT_CODEL) (NEW)
    |  > 3. Fair Queue Controlled Delay (DEFAULT_FQ_CODEL)
    |    4. Stochastic Fair Queue (DEFAULT_SFQ) (NEW)
    |    5. Priority FIFO Fast (DEFAULT_PFIFO_FAST)
    |  choice[1-5?]:
    |Error in reading or end of file.
    
    Signed-off-by: Christian Lamparter <chunkeey at gmail.com>
---
 target/linux/bcm27xx/bcm2708/config-5.10 | 3 +++
 target/linux/bcm27xx/bcm2709/config-5.10 | 3 +++
 target/linux/bcm27xx/bcm2710/config-5.10 | 5 +++++
 target/linux/bcm27xx/bcm2711/config-5.10 | 5 +++++
 4 files changed, 16 insertions(+)

diff --git a/target/linux/bcm27xx/bcm2708/config-5.10 b/target/linux/bcm27xx/bcm2708/config-5.10
index c5f71a8636..56e076ba95 100644
--- a/target/linux/bcm27xx/bcm2708/config-5.10
+++ b/target/linux/bcm27xx/bcm2708/config-5.10
@@ -299,6 +299,7 @@ CONFIG_RESET_CONTROLLER=y
 # CONFIG_RESET_RASPBERRYPI is not set
 CONFIG_RESET_SIMPLE=y
 # CONFIG_RPIVID_MEM is not set
+# CONFIG_RPI_AXIPERF is not set
 # CONFIG_RPI_POE_POWER is not set
 CONFIG_SCSI=y
 # CONFIG_SCSI_LOWLEVEL is not set
@@ -318,6 +319,8 @@ CONFIG_SERIAL_MCTRL_GPIO=y
 CONFIG_SERIAL_OF_PLATFORM=y
 CONFIG_SG_POOL=y
 CONFIG_SMSC_PHY=y
+# CONFIG_SND_SOC_AD193X_I2C is not set
+# CONFIG_SND_SOC_AD193X_SPI is not set
 CONFIG_SPARSE_IRQ=y
 CONFIG_SRCU=y
 # CONFIG_STRIP_ASM_SYMS is not set
diff --git a/target/linux/bcm27xx/bcm2709/config-5.10 b/target/linux/bcm27xx/bcm2709/config-5.10
index e4d4b9c67c..f15f6e3562 100644
--- a/target/linux/bcm27xx/bcm2709/config-5.10
+++ b/target/linux/bcm27xx/bcm2709/config-5.10
@@ -376,6 +376,7 @@ CONFIG_RESET_RASPBERRYPI=y
 CONFIG_RESET_SIMPLE=y
 CONFIG_RFS_ACCEL=y
 # CONFIG_RPIVID_MEM is not set
+# CONFIG_RPI_AXIPERF is not set
 # CONFIG_RPI_POE_POWER is not set
 CONFIG_RPS=y
 CONFIG_RWSEM_SPIN_ON_OWNER=y
@@ -399,6 +400,8 @@ CONFIG_SG_POOL=y
 CONFIG_SMP=y
 CONFIG_SMP_ON_UP=y
 CONFIG_SMSC_PHY=y
+# CONFIG_SND_SOC_AD193X_I2C is not set
+# CONFIG_SND_SOC_AD193X_SPI is not set
 CONFIG_SPARSE_IRQ=y
 CONFIG_SRCU=y
 # CONFIG_STRIP_ASM_SYMS is not set
diff --git a/target/linux/bcm27xx/bcm2710/config-5.10 b/target/linux/bcm27xx/bcm2710/config-5.10
index a0d4b9ba11..39c00762ba 100644
--- a/target/linux/bcm27xx/bcm2710/config-5.10
+++ b/target/linux/bcm27xx/bcm2710/config-5.10
@@ -37,6 +37,8 @@ CONFIG_ARM64_VA_BITS=39
 CONFIG_ARM64_VA_BITS_39=y
 CONFIG_ARM64_VHE=y
 CONFIG_ARM64_WORKAROUND_CLEAN_CACHE=y
+CONFIG_ARM64_WORKAROUND_REPEAT_TLBI=y
+CONFIG_ARM64_WORKAROUND_SPECULATIVE_AT=y
 CONFIG_ARM_AMBA=y
 CONFIG_ARM_ARCH_TIMER=y
 CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y
@@ -362,6 +364,7 @@ CONFIG_RESET_SIMPLE=y
 CONFIG_RFS_ACCEL=y
 CONFIG_RODATA_FULL_DEFAULT_ENABLED=y
 # CONFIG_RPIVID_MEM is not set
+# CONFIG_RPI_AXIPERF is not set
 # CONFIG_RPI_POE_POWER is not set
 CONFIG_RPS=y
 CONFIG_RWSEM_SPIN_ON_OWNER=y
@@ -384,6 +387,8 @@ CONFIG_SERIAL_OF_PLATFORM=y
 CONFIG_SG_POOL=y
 CONFIG_SMP=y
 CONFIG_SMSC_PHY=y
+# CONFIG_SND_SOC_AD193X_I2C is not set
+# CONFIG_SND_SOC_AD193X_SPI is not set
 CONFIG_SPARSEMEM=y
 CONFIG_SPARSEMEM_EXTREME=y
 CONFIG_SPARSEMEM_MANUAL=y
diff --git a/target/linux/bcm27xx/bcm2711/config-5.10 b/target/linux/bcm27xx/bcm2711/config-5.10
index b4798353fd..ed095231ae 100644
--- a/target/linux/bcm27xx/bcm2711/config-5.10
+++ b/target/linux/bcm27xx/bcm2711/config-5.10
@@ -37,6 +37,8 @@ CONFIG_ARM64_VA_BITS=39
 CONFIG_ARM64_VA_BITS_39=y
 CONFIG_ARM64_VHE=y
 CONFIG_ARM64_WORKAROUND_CLEAN_CACHE=y
+CONFIG_ARM64_WORKAROUND_REPEAT_TLBI=y
+CONFIG_ARM64_WORKAROUND_SPECULATIVE_AT=y
 CONFIG_ARM_AMBA=y
 CONFIG_ARM_ARCH_TIMER=y
 CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y
@@ -374,6 +376,7 @@ CONFIG_RESET_SIMPLE=y
 CONFIG_RFS_ACCEL=y
 CONFIG_RODATA_FULL_DEFAULT_ENABLED=y
 # CONFIG_RPIVID_MEM is not set
+# CONFIG_RPI_AXIPERF is not set
 # CONFIG_RPI_POE_POWER is not set
 CONFIG_RPS=y
 CONFIG_RWSEM_SPIN_ON_OWNER=y
@@ -395,6 +398,8 @@ CONFIG_SERIAL_MCTRL_GPIO=y
 CONFIG_SERIAL_OF_PLATFORM=y
 CONFIG_SG_POOL=y
 CONFIG_SMP=y
+# CONFIG_SND_SOC_AD193X_I2C is not set
+# CONFIG_SND_SOC_AD193X_SPI is not set
 CONFIG_SPARSEMEM=y
 CONFIG_SPARSEMEM_EXTREME=y
 CONFIG_SPARSEMEM_MANUAL=y